huawei(config)#interface gau
{ frameid/slotid<S><1,15> }:0/9
Command:
interface gau 0/9
huawei(config-if-gau-0/9)#
huawei(config-if-gau-0/9)#display port opticstate
{ portid<U><0,0> }:0
Command:
display port opticstate 0
huawei(config-if-gau-0/9)#
Optics/electric module status is normal
Optics/electric module information
Identifier : SFP
Ext.Identifier : GBIC/SFP function is defined by
serial
ID only
Connector : LC
Transceiver
Infiniband compliance codes : invalid
SONET compliance codes : invalid
GE compliance codes : 1000BASE-LX
Link length : invalid
Transmitter technology : invalid
Transmission media : invalid
Speed : invalid
Encoding : 8B10B
BR,Nominal : 1200 MBits/sec
Length(9um)-km : 10 km
Length(9um) : 10.0 km
Length(50um) : 550 m
Length(62.5um) : 550 m
Length(Copper) : 0 m
Vendor name : AGILENT
Vendor OUI : 12499
Vendor PN : HFCT-5710L
Vendor rev :
Wavelength : 0 nm
Cc_base : 0xcb
Options : TX_DISABLE is implemented and
disables
the serial output
BR,max : Unspecified
BR,min : Unspecified
Vendor SN : AA0612022Y
Date code : 06 03 24
Diagnostic Monitoring Type : invalid
Enhanced Options : invalid
SFF-8472 Compliance : Not included or undefined
CC_EXT : 0x81
Vendor specific :
30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30
30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30
huawei(config-if-ipm-0/2)#display port state
{ portid<U><0,7>|all<K> }:all
Command:
display port state all
---------------------------------------------------------------------------
Port Port Native MDI Speed Duplex Flow- Active Link
Type VLAN (Mbps) Control State
---------------------------------------------------------------------------
0 GE 1 - 1000 full off active
offline
1 GE 2 - 1000 full off active
offline
2 FE 1 auto 100 full off active
offline
3 FE 1 auto 100 full off active
offline
4 FE 1 auto 100 full off active
offline
5 FE 1 auto 100 full off active
offline
6 FE 1 auto 100 full off active
offline
7 FE 1 auto 100 full off active
offline
---------------------------------------------------------------------------
To query the configuration and status of GE optical portt 0/2/0, do as follows:
huawei(config-if-ipm-0/2)#display port state
{ portid<U><0,7>|all<K> }:0
Command:
display port state 0
The port is active
Native VLAN ID is 1
Ethernet port is offline
Ethernet port is full duplex
Ethernet port rate is 1000M
Ethernet port does not support flow control
Ethernet port does not support line-selfadaptive
To query the configuration and status of GE electrical port. 0/3/0, do as follows:
UA5000(config-if-ipm-0/3)#display port state 0
Optics/electrics module status is normal
The port is active
Native VLAN ID is 1
Ethernet port is offline
Ethernet port duplex is auto-negotiation
Ethernet port rate is auto-negotiation
Ethernet port does not support flow control
Line-adaptive function of the ethernet port is auto-negotiation
To query the configuration and status of FE electrical port. 0/2/3, do as follows:
huawei(config-if-ipm-0/2)#display port state
{ portid<U><0,7>|all<K> }:3
Command:
display port state 3
The port is active
Native VLAN ID is 1
Ethernet port is offline
Ethernet port is full duplex
Ethernet port rate is 100M
Ethernet port does not support flow control
Line-adaptive function of the ethernet port is auto-negotiation
3 PSTN Normal NoLoop,NoTest
4 PSTN Normal NoLoop,NoTest
5 PSTN Normal NoLoop,NoTest
6 PSTN Normal NoLoop,NoTest
7 PSTN Normal NoLoop,NoTest
8 PSTN Normal NoLoop,NoTest
9 PSTN Normal NoLoop,NoTest
10 PSTN Normal NoLoop,NoTest
11 PSTN Normal NoLoop,NoTest
12 PSTN Normal NoLoop,NoTest
13 PSTN Normal NoLoop,NoTest
14 PSTN Normal NoLoop,NoTest
15 PSTN Normal NoLoop,NoTest
16 PSTN Normal NoLoop,NoTest
17 PSTN Normal NoLoop,NoTest
18 PSTN Normal NoLoop,NoTest
19 PSTN Normal NoLoop,NoTest
20 PSTN Normal NoLoop,NoTest
21 PSTN Normal NoLoop,NoTest
22 PSTN Normal NoLoop,NoTest
23 PSTN Normal NoLoop,NoTest
24 PSTN Normal NoLoop,NoTest
25 PSTN Normal NoLoop,NoTest
26 PSTN Normal NoLoop,NoTest
27 PSTN Normal NoLoop,NoTest
28 PSTN Normal NoLoop,NoTest
29 PSTN Normal NoLoop,NoTest
30 PSTN Normal NoLoop,NoTest
31 PSTN Normal NoLoop,NoTest
32 PSTN Normal NoLoop,NoTest
33 PSTN Normal NoLoop,NoTest
34 PSTN Normal NoLoop,NoTest
35 PSTN Normal NoLoop,NoTest
36 PSTN Normal NoLoop,NoTest
37 PSTN Normal NoLoop,NoTest
38 PSTN Normal NoLoop,NoTest
39 PSTN Normal NoLoop,NoTest
40 PSTN Normal NoLoop,NoTest
41 PSTN Normal NoLoop,NoTest
42 PSTN Normal NoLoop,NoTest
43 PSTN Normal NoLoop,NoTest
44 PSTN Normal NoLoop,NoTest
45 PSTN Normal NoLoop,NoTest
46 PSTN Normal NoLoop,NoTest
47 PSTN Normal NoLoop,NoTest
---------------------------------------------------------------------
09_M_ERT_01(config)#interface adsl 0/3
09_M_ERT_01(config-if-adsl-0/3)#activate 1
{ <cr>|profile-index<K>|profile-name<K> }:
Command:
activate 1
09_M_ERT_01(config-if-adsl-0/3)#
Send the command to activate port 1 successfully
09_M_ERT_01(config-if-adsl-0/3)#quit
09_M_ERT_01(config)#display line operation port 0/3/1
It will take several minutes, and console may be timeout, please use command
idle-timeout to set time limit
Are you sure to continue? (y/n)[n]:y
Failure: Port 1 is not activated
09_M_ERT_01(config)#telnet 172.28.9.30
{ <cr>|service-port<U><1,65535> }:
Command:
telnet 172.28.9.30
Press CTRL_] to quit telnet mode
Trying 172.28.9.30 ...
Connected to 172.28.9.30 ...
>>User name:root
>>User password:
Huawei Integrated Access Software (MA5600T).
Copyright(C) Huawei Technologies Co., Ltd. 2002-2013. All rights reserved.
-----------------------------------------------------------------------------
User last login information:
-----------------------------------------------------------------------------
Access Type : Telnet
IP-Address : 172.28.9.84
Login Time : 2016-11-23 14:11:59+01:00
Logout Time : 2016-11-23 14:16:26+01:00
-----------------------------------------------------------------------------
-----------------------------------------------------------------------------
All user fail login information:
-----------------------------------------------------------------------------
Access Type IP-Address Time Login Times
-----------------------------------------------------------------------------
Telnet 172.28.9.84 2016-11-22 12:04:05+01:00 5
Telnet 172.28.9.83 2016-11-17 09:06:47+01:00 2
-----------------------------------------------------------------------------
User root has used a default password. Change the password in time.
09_M_Orangerie_001>
09_M_Orangerie_001>
09_M_Orangerie_001>
09_M_Orangerie_001>
09_M_Orangerie_001>enable
09_M_Orangerie_001#config
09_M_Orangerie_001(config)#display line operation ?
---------------------------------------------
Command of privilege Mode:
---------------------------------------------
all Display all line operation
board Frame ID/Slot ID
port Frame ID/Slot ID/Port ID
09_M_Orangerie_001(config)#display line operation port
{ frame/slot/port<S><Length 5-15> }:
Command:
display line operation port
% Incomplete command, the error locates at '^'
09_M_Orangerie_001(config)#display board 0
-------------------------------------------------------------------------
SlotID BoardName Status SubType0 SubType1 Online/Offline
-------------------------------------------------------------------------
0
1 H80BCAME Normal
2 H80BCAME Normal
3 H80BCAME Normal
4 H80BCAME Normal
5 H80BCAME Normal
6 H80BCAME Normal
7 H80BCAME Normal
8 H80BCAME Normal
9 H802SCUN Active_normal FLBA
10 H802SCUN Standby_normal FLBA
11 H80BCAME Normal
12 H80BCAME Normal
13 H80BCAME Normal
14 H80BCAME Normal
15 H80BCAME Normal
16 H80BCAME Normal
17
18
19
20
21
22
-------------------------------------------------------------------------
09_M_Orangerie_001(config)#
09_M_Orangerie_001(config)#
09_M_Orangerie_001(config)#
09_M_Orangerie_001(config)#
09_M_Orangerie_001(config)#display line operation port ?
---------------------------------------------
Command of privilege Mode:
---------------------------------------------
frame/slot/port<S><Length 5-15>
Frame ID/Slot ID/Port ID
09_M_Orangerie_001(config)#display line operation port 0/3/0 ?
---------------------------------------------
Command of privilege Mode:
---------------------------------------------
<cr> Please press ENTER to execute command
09_M_Orangerie_001(config)#display line operation port 0/3/0
It will take several minutes, and console may be timeout, please use command
idle-timeout to set time limit
Are you sure to continue? (y/n)[n]:y
Failure: Port 0 is not activated
09_M_Orangerie_001(config)#display board 0/1
---------------------------------------
Board Name : H80BCAME
Board Status : Normal
---------------------------------------
------------------------------------------------------------------------------
Power Status Power-off cause Power-off Time
------------------------------------------------------------------------------
POWER-ON - -
------------------------------------------------------------------------------
-----------------------------------------------------------------------------
Port Port Type Port Status Line Profile Alarm Profile Ext Profile
-----------------------------------------------------------------------------
0 ADSL Activating 3 1 --
1 ADSL Activated 3 1 --
2 ADSL Activated 3 1 --
3 ADSL Activated 3 1 --
4 ADSL Activated 3 1 --
5 ADSL Activating 3 1 --
6 ADSL Activating 3 1 --
7 ADSL Activated 3 1 --
8 ADSL Activating 3 1 --
9 ADSL Activating 3 1 --
10 ADSL Activating 3 1 --
11 ADSL Activated 3 1 --
12 ADSL Activated 3 1 --
13 ADSL Activating 3 1 --
14 ADSL Activated 3 1 --
15 ADSL Activating 3 1 --
16 ADSL Activated 3 1 --
17 ADSL Activated 3 1 --
09_M_Orangerie_001(config)#uit
% Unknown command, the error locates at '^'
09_M_Orangerie_001(config)#display line operation port 0/1/2
It will take several minutes, and console may be timeout, please use command
idle-timeout to set time limit
Are you sure to continue? (y/n)[n]:y
------------------------------------------------------------------------------
Channel mode : Interleaved
Downstream channel bit swap : Disable
Upstream channel bit swap : Disable
Trellis mode : Enable
Result of the last full initialization : No failure
Standard in port training : G992.5-Annex A
G.998.4 retransmission used : Unused, retransmission
mode is forbidden
Downstream actual data rate(Kbps) : 2047
Downstream previous data rate(Kbps) : 2047
Downstream max. attainable rate(Kbps) : 27356
Downstream actual line rate(Kbps) : 2066
Downstream signal attenuation(dB) : 7.9
Downstream channel SNR margin(dB) : 29.7
Downstream channel delay(ms) : 13
Downstream channel attenuation(dB) : 7.9
Downstream total output power(dBm) : 0.4
Downstream actual PSD(dBm/Hz) : -49.7
Downstream net data rate in low power state(Kbps): -
Upstream actual data rate(Kbps) : 509
Upstream previous data rate(Kbps) : 509
Upstream max. attainable rate(Kbps) : 1194
Upstream actual line rate(Kbps) : 520
Upstream signal attenuation(dB) : 4.3
Upstream channel SNR margin(dB) : 19.3
Upstream channel delay(ms) :6
Upstream channel attenuation(dB) : 4.5
Upstream total output power(dBm) : 5.1
Upstream actual PSD(dBm/Hz) : -45.0
Upstream net data rate in low power state(Kbps) : -
Current power management state : Full-on state
------------------------------------------------------------------------------
Note: The 102.3 dB signal attenuation, 102.3 dB channel attenuation,
and -51.2 dB SNR margin indicate that the parameters are not within
their specified ranges.
G.992.1 : G.dmt
G.992.2 : G.lite
G.992.3 : G.dmt.bis
G.992.5 : G.dmt.bisplus
09_M_Orangerie_001(config)#
09_M_Orangerie_001(config)#quit
09_M_Orangerie_001#quit
Check whether system data has been changed. Please save data before logout.
Are you sure to log out? (y/n)[n]:y
09_M_Orangerie_001#
Configuration console exit, please retry to log on
The connection was closed by the remote host
09_M_ERT_01(config)#
09_M_ERT_01(config)#
09_M_ERT_01(config)#quit
09_M_ERT_01#quit
Check whether system data has been changed. Please save data before logout.
Are you sure to log out? (y/n)[n]:y
09_M_ERT_01#
Configuration console exit, please retry to log on
