GRUNDFOS CR SERVICE MANUAL

CR3
Parts List & Kits

Contents

Parts List
Spare Part Kits
Accessories
Special Tools
Standard Tools
Tools for Torques
 Exploded View CR3

2
 Parts List & Kits CR3

Pos. No. B.O.M. Material Included

No. Part Description Model Stages Used Comments/Dimensions Ref. No. No. in kits ?

parts list
1 Adapter for Motor Stool For NEMA, 213/215TC, 7.5 - 10HP 96476208 No
2 Motor Stool 3/2-12 1 NEMA, 56C, 1/3 - 2HP 96436501 No
13-25 1 NEMA, 182/184TC, 3 - 5HP 96436502 No
Add Pos. 1, NEMA, 213TC, 7.5 - 10HP 96436502 No
3/2-7 1 IEC, F85, MG 71, .37 - .55kW 96436495 No
8-15 1 IEC, F100, MG 80, .75 - 1.1kW 96436496 No
17-29 1 IEC, F115, MG 90, 1.5 - 2.2kW 96436499 No
31-36 1 IEC, F130, MG 100/112, 3.0 - 4.0 kW 96436500 No
IEC, F265, MG132, 5.5 - 7.5kW 96436505 No
4 Chamber, Complete with Pos.45 & 65 3/2-36 ^^^ PTFE Pos.45 96439480 No
4a Chamber Cpl. w/Pos.45 & 65 & Bearing 3/2-36 ^^^^ Silicon Carbide Brg, PTFE Pos.45 96439475 YES
Chamber Cpl. w/Pos.45 & 65 & Brg. (option) 3/2-36 ^^^^ Bronze Bearing, PTFE Pos.45 96440612 YES
3/2-36 ^^^^ Graflon Bearing, PTFE Pos.45 96440615 YES
5a Chamber, Bottom Complete with Pos.45 & 65 3/2-36 1 PTFE Pos.45 96439484 No
Chmb. Btm. Cpl. w/Pos.45 & 65 (Low NPSH opt.) 3/2-36 1 PTFE Pos.45 96465891 No
6 Base 3/2-17 1 Oval (max 232 PSI) 96436516 No
3/2-36 1 JIS, FGJ, ANSI (Max 362 PSI) 96442012 No
7 Coupling Guard 2 IEC, F85-F100 96438136 No
2 NEMA-56C, IEC-F115,130, & 265 96438137 No
2 NEMA, 182-215TC 96438138 No
7a Screw for Coupling Guard 3/2-36 4 M4 x 8mm 96488481 No
9 Allen Screw 3/2-19 4 M6 x 20mm, Delta Seal 00ID7899 YES
21-27 4 M8 x 25mm, Delta Seal 00ID7900 YES
M10 x 25mm, Delta Seal 00ID7901 YES
10 Shaft Pin 3/2-36 1 ø5 x 26mm 310192 YES
10a Coupling Half 3/2-12 2 NEMA, 56C, 1/3 - 2HP. ø15.8 / ø12 410108 YES
13-25 2 NEMA, 182/184TC, 3-5HP. ø28.5/ø12 410109 YES
NEMA, 213TC, 7.5-10HP. ø34.9/ø12 96472175 YES
3/2-7 2 IEC, F85, MG71, .37-.55kW. ø14/ø12 410041 YES
8-15 2 IEC, F100, MG80,.75-1.1kW. ø19/ø12 410043 YES
17-29 2 IEC, F115, MG 90, 1.5-2.2kW. ø24/ø12 410045 YES
31-36 2 IEC, F130, MG100/112, 3-4 kW.ø28/ø12 410047 YES
IEC, F265, MG132, 5.5-7.5kW. ø38/ø12 410115 YES
12 Oval Flange 3/2-17 2 Painted CI, 1” -11.5 NPT (max 232 PSI) 96468333 YES
3/2-23 2 Painted CI, RP 1” BSP DIN (max 232 PSI) 400173 No
18 Priming/Vent Plug 3/2-36 * G 1/2A, NV24 with NV9 x M8 stem 405150 No
23 Plug 3/2-36 ** G 1/2A, w/1/4”port, NV24 91120659 No
Plug (option) 3/2-36 ** G 1/2A, Solid no port, NV24 370025 No
23c Pipe Plug for Pos.23 & 25 with hollow stem 3/2-36 ** 1/4” NPT,SS SQHD 00ID7216 No
25 Drain/Priming Plug Cpl. with O-rings 3/2-36 1 G 1/2A, NV24 w/NV9 x M8 stem, EPDM 96440608 No
3/2-36 1 G 1/2A, NV24 w/NV9 x M8 stem, FKM 96440609 No
3/2-36 1 G 1/2A, NV24 w/NV9 x M8 stem, FFKM 96486530 No
Dr./Pr. Plug Cpl. for gauge, w/O-rings (option) 3/2-36 1 G 1/2A, NV24 w/NV9 x M8 hollow stem, EPDM 96527046 No
3/2-36 1 G 1/2A, NV24 w/NV9 x M8 hollow stem, FKM 96527047 No
3/2-36 1 G 1/2A, NV24 w/NV9 x M8 hollow stem, FFKM 96527049 No
26 Staybolt 3/2-3 4 M12 x 79mm 404002 No
4 4 M12 x 97mm 414002 No
5 4 M12 x 115mm 404004 No
6 4 M12 x 133mm 404005 No
7 4 M12 x 151mm 414004 No
8 4 M12 x 169mm 404007 No
9 4 M12 x 187mm 404008 No
10 4 M12 x 205mm 414006 No
11 4 M12 x 223mm 404010 No
12 4 M12 x 241mm 404011 No
13 4 M12 x 259mm 414008 No
15 4 M12 x 294mm 96442754 No
17 4 M12 x 330mm 96442760 No
19 4 M12 x 367mm 414012 No
21 4 M12 x 402mm 96442762 No
23 4 M12 x 439mm 404022 No
25 4 M12 x 475mm 414016 No
27 4 M12 x 511mm (50Hz.) 404026 No
29 4 M12 x 546mm (50Hz.) 96442765 No
31 4 M12 x 583mm (50Hz.) 404030 No
33 4 M12 x 618mm (50Hz.) 96442767 No
36 4 M12 x 670mm (50Hz.) 96442768 No
Staybolt (Back-to-Back & Tandem Seal option) 3/2-3 4 M12 x 187mm 404008 No
4 4 M12 x 205mm 414006 No
5 4 M12 x 223mm 404010 No
6 4 M12 x 241mm 404011 No
7 4 M12 x 259mm 414008 No
8 4 M12 x 277mm 404013 No
Due to part changes over time, all position numbers These columns indicates which model uses the spare part. If blank, the part is used in all models.
(1-203) may not be used.

3
Parts List & Kits CR3

Pos. No. B.O.M. Material Included

No. Part Description Model Stages Used Comments/Dimensions Ref. No. No. in kits ?

parts list
26 Staybolt (Back-to-Back & Tandem Seal option) 9 4 M12 x 294mm 96442754 No
10 4 M12 x 313mm 414010 No
11 4 M12 x 330mm 96442760 No
12 4 M12 x 340mm 414011 No
13 4 M12 x 367mm 414012 No
15 4 M12 x 402mm 96442762 No
17 4 M12 x 436mm 96458181 No
19 4 M12 x 475mm 414016 No
21 4 M12 x 511mm 404026 No
23 4 M12 x 546mm 96442765 No
25 4 M12 x 583mm 404030 No
27 4 M12 x 618mm (50Hz.) 96442767 No
29 4 M12 x 655mm (50Hz.) 96458442 No
31 4 M12 x 691mm (50Hz.) 96442777 No
33 4 M12 x 724mm (50Hz.) 96442769 No
36 4 M12 x 778mm (50Hz.) 96458444 No
28 Motor Bolt 3/2-12 4 NEMA, 56C, 1/3 - 2HP. UNC 3/8” x 25mm 00ID1839 No
13-25 4 NEMA, 182/184TC, 3 - 5HP.UNC1/2” x 25mm 00ID1840 No
NEMA, 213TC, 7.5 -10HP. UNC 1/2” x 1.25” 91128631 No
3/2-7 4 IEC, F85, MG71, .37-.55kW. M6 x 20mm 00ID8022 No
8-15 4 IEC, F100, MG80,.75-1.1kW. M6 x 25mm 00ID8023 No
17-29 4 IEC, F115, MG 90, 1.5-2.2kW. M8 x 20mm 00ID8024 No
31-36 4 IEC, F130, MG100/112, 3-4 kW. M8 x 25mm 00ID8025 No
IEC, F265, MG132, 5.5-7.5kW. M12 x 45mm 00ID7914 No
35 Hexagon Head Screw for Oval Flange 3/2-17 4 M10 x 40mm, Delta Seal 00ID8027 YES
36 Staybolt Nut 3/2-36 4 19mm x M12, Delta Seal 00ID7917 No
37 Sleeve O-ring 3/2-36  EPDM, ø137.5 x 3.3mm 96438743 YES
3/2-36  FKM, ø137.5 x 3.3mm 96438744 YES
37b Sleeve O-ring (option) 3/2-36  FXM, ø137.5 x 3.3mm 96458109 YES
3/2-36  FFKM, ø136.12 x 3.53mm 96466718 YES
38 Drain Plug O-ring 3/2-36 1 EPDM, ø16.3 x 2.4mm 00ID1288 YES
3/2-36 1 FKM, ø16.3 x 2.4mm 00ID2231 YES
Drain Plug O-ring (option) 3/2-36 1 FFKM, ø16.3 x 2.4mm 96428162 YES
3/2-36 1 FXM, ø16.3 x 2.4mm 96442869 YES
39 Gasket for Oval Flange 3/2-17 2 95 x 55 x ø35 x 2mm, KLINGERSIL C4430 400189 YES
45 Neck Ring 3/2-36 # stgs ø41.3 x ø30.6 x .75mm, PTFE 400003 YES
47a Bearing Ring/Spacer 3/2-36 ^^^^ SiC 150, ø17.37 x ø13.10 x ø10.9 x 13mm 96437488 YES
Brg. Ring/Spacer (option for Graflon / Brz. 4a) 3/2-36 ^^^^ TC, ø15.92 x ø13.10 x ø10.9 x 9.7mm 400041 YES
49 Impeller 3/2-36 # stgs- ø73.6 x ø30.6 x 9.55mm (back-plate .5mm) 96433168 No
49i Impeller (Low NPSH option) 3/2-36 1 ø73.0 x ø35.0 x 13.2mm (back-plate 1.0mm) 96437414 No
50a Top Guide Vane 3-36 1 96439456 No
Top Guide Vane Plate (option for destaging) 3/2 1 96478562 No
51 Shaft, Complete 3/2-3 1 ø12 x 160.5mm 96439607 No
4 1 ø12 x 180.5mm 96440386 No
5 1 ø12 x 196.5mm 96440387 No
6 1 ø12 x 214.5mm 96440388 No
7 1 ø12 x 234.5mm 96440389 No
8 1 ø12 x 250.5mm 96440390 No
9 1 ø12 x 268.5mm 96440391 No
10 1 ø12 x 288.5mm 96440392 No
11 1 ø12 x 304.5mm 96440393 No
12 1 ø12 x 322.5mm 96440394 No
13 1 ø12 x 342.5mm 96440395 No
15 1 ø12 x 376.5mm 96440396 No
17 1 ø12 x 412.5mm 96440398 No
19 1 ø12 x 450.5mm 96440400 No
21 1 ø12 x 484.5mm 96440401 No
23 1 ø12 x 520.5mm 96440403 No
25 1 ø12 x 556.5mm 96440405 No
27 1 ø12 x 592.5mm (50 Hz.) 96440406 No
29 1 ø12 x 628.5mm (50 Hz.) 96440407 No
31 1 ø12 x 664.5mm (50 Hz.) 96440409 No
33 1 ø12 x 700.5mm (50 Hz.) 96440410 No
36 1 ø12 x 754.5mm (50 Hz.) 96440411 No
Shaft, Cpl. (Back-to-Back & Tandem Seal option) 3/2-3 1 ø12 x 265.5mm 96457560 No
4 1 ø12 x 285.5mm 96457561 No
5 1 ø12 x 301.5mm 96457562 No
6 1 ø12 x 319.5mm 96457563 No
7 1 ø12 x 339.5mm 96457564 No
8 1 ø12 x 355.5mm 96457565 No
9 1 ø12 x 373.5mm 96457566 No
10 1 ø12 x 393.5mm 96457567 No
11 1 ø12 x 409.5mm 96457568 No
Due to part changes over time, all position numbers These columns indicates which model uses the spare part. If blank, the part is used in all models.
(1-203) may not be used.

4
 Parts List & Kits CR3

Pos. No. B.O.M. Material Included

No. Part Description Model Stages Used Comments/Dimensions Ref. No. No. in kits ?

parts list
51 Shaft, Cpl. (Back-to-Back & Tandem Seal option) 12 1 ø12 x 427.5mm 96457569 No
13 1 ø12 x 447.5mm 96457570 No
15 1 ø12 x 481.5mm 96457571 No
17 1 ø12 x 517.5mm 96457573 No
19 1 ø12 x 555.5mm 96457575 No
21 1 ø12 x 589.5mm 96457576 No
23 1 ø12 x 625.5mm 96457578 No
25 1 ø12 x 661.5mm 96457580 No
27 1 ø12 x 697.5mm (50 Hz.) 96457581 No
29 1 ø12 x 733.5mm (50 Hz.) 96457582 No
31 1 ø12 x 769.5mm (50 Hz.) 96457584 No
33 1 ø12 x 805.5mm (50 Hz.) 96457585 No
36 1 ø12 x 859.5mm (50 Hz.) 96457586 No
55 Outer Sleeve 3/2-3 1 ø138 x 44.6mm 96437865 No
4 1 ø138 x 62.6mm 96440010 No
5 1 ø138 x 80.6mm 96441510 No
6 1 ø138 x 98.6mm 96439999 No
7 1 ø138 x 116.6mm 96441511 No
8 1 ø138 x 134.6mm 96441513 No
9 1 ø138 x 152.6mm 96440000 No
10 1 ø138 x 170.6mm 96441514 No
11 1 ø138 x 188.6mm 96441516 No
12 1 ø138 x 206.6mm 96440001 No
13 1 ø138 x 224.6mm 96441517 No
15 1 ø138 x 260.6mm 96440002 No
17 1 ø138 x 296.6mm 96441520 No
19 1 ø138 x 332.6mm 96441521 No
21 1 ø138 x 368.6mm 96440004 No
23 1 ø138 x 404.6mm 96441524 No
25 1 ø138 x 440.6mm 96441525 No
27 1 ø138 x 476.6mm (50 Hz.) 96440006 No
29 1 ø138 x 512.6mm (50 Hz.) 96441526 No
31 1 ø138 x 548.6mm (50 Hz.) 96441527 No
33 1 ø138 x 584.6mm (50 Hz.) 96440008 No
36 1 ø138 x 638.6mm (50 Hz.) 96439652 No
60 Stack Compression Spring 3/2-36 1 ø136 x 3.5mm 96439662 No
64 Spacing Pipe 2-36 ^^^ ø15.85 x ø12.85 x 17.52mm 400035 No
64a Spacing Pipe 3/2-36 ^^^^ ø15.85 x ø12.85 x 4.5mm 96440292 YES
Spacing Pipe (option for Graflon / Brz. 4a) 3/2-36 ^^^^ Use with TC Pos.47a, ø15 x ø12.7 x 7.8mm 400016 YES
64c Clamp, Splined 3/2-36 1 ø15 x ø13.10 x ø10.9 x 13mm 96439668 YES
65 Neck Ring Retainer 3/2-36 # stgs ø43.5 x ø34.0 x 3.6mm 96438746 YES
66 Lock Washer Set for Shaft 3/2-36 1 ø13.5 x ø8.2 x 2.6mm 96417297 YES
66a Washer for Staybolt 3/2-36 4 DIN 125A, ø24 x ø13 x 2.5mm, Delta Seal 96430377 No
67 Lock Nut for Shaft 3/2-36 1 13mm x M8 00ID2061 YES
69 Spacing Pipe 3/2 1 ø15.85 x 12.85 x 18.0mm 400125 No
76 Nameplate 3/2-36 1 304SS, 60 x 45mm 96439820 No
76a Rivet for Nameplate 3/2-36 2 304SS, ø3 x 5mm 96022882 No
77a Pump Head Cov. for Back-to-Back , Tandem Seal 3/2-36 1 Cast Stainless 96456293 No
100 Priming/Vent Plug O-ring 3/2-36  EPDM, ø16.3 x 2.4mm 00ID1288 YES
3/2-36  FKM, ø16.3 x 2.4mm 00ID2231 YES
100a Priming/Vent Plug O-ring (option) 3/2-36  FFKM, ø16.3 x 2.4mm 96428162 No
3/2-36  FXM, ø16.3 x 2.4mm 96442869 No
102 O-ring for Pos. 105b Back-to-Back 3/2-36 1 EPDM, ø18 x 2.5mm 00ID2041 YES
3/2-36 1 FKM, ø17.86 x 2.62mm 00ID2187 YES
O-ring for Pos. 105b Back-to-Back (option) 3/2-36 1 FFKM, ø17.86 x 2.62mm 96440281 No
3/2-36 1 FXM, ø17.86 x 2.62mm 96472584 No
103 Stationary Seal Ring for 105b Back-to-Back 3/2-36 1 TC, 12mm 980190 No
Stationary Seal Ring for 105b Back-to-Back (opt.) 3/2-36 1 SiC,12mm 980746 YES
104 Rotating Seal Ring for 105b Back-to-Back 3/2-36 1 TC, 12mm 980163 No
Rotating Seal Ring for 105b Back-to-Back (opt.) 3/2-36 1 SiC, 12mm 980733 YES
105(b) Shaft Seal HQBE 3/2-36 *** SiC, Carbon with resin-impregnated, EPDM 96441879 YES
Shaft Seal HQBV 3/2-36 *** SiC, Carbon with resin-impregnated, FKM 96441880 YES
Shaft Seal HQBK (option) 3/2-36 *** SiC, Carbon with resin-impregnated, FFKM 96489537 YES
Shaft Seal HQQE 3/2-36 *** SiC, SiC, EPDM 96441877 YES
Shaft Seal HQQV 3/2-36 *** SiC, SiC, FKM 96441878 YES
Shaft Seal HQQF (option) 3/2-36 *** SiC, SiC, FXM 96472620 YES
Shaft Seal HQQK (option) 3/2-36 *** SiC, SiC, FFKM 96464381 YES
Shaft Seal HUBE 3/2-36 *** TC, Carbon with resin-impregnated, EPDM 96441873 YES
Shaft Seal HUBV 3/2-36 *** TC, Carbon with resin-impregnated, FKM 96441874 YES
Shaft Seal HUBF (option) 3/2-36 *** TC, Carbon with resin-impregnated, FXM 96481464 YES
Shaft Seal HUBK (option) 3/2-36 *** TC, Carbon with resin-impregnated, FFKM 96481463 YES
Shaft Seal HUUE 3/2-36 *** TC, TC, EPDM 96441875 YES
Due to part changes over time, all position numbers These columns indicates which model uses the spare part. If blank, the part is used in all models.
(1-203) may not be used.

5
Parts List & Kits CR3

Pos. No. B.O.M. Material Included

No. Part Description Model Stages Used Comments/Dimensions Ref. No. No. in kits ?

parts list
105(b) Shaft Seal HUUV 3/2-36 *** TC, TC, FKM 96441876 YES
Shaft Seal HUUF (option) 3/2-36 *** TC, TC, FXM 96475542 YES
Shaft Seal HUUK (option) 3/2-36 *** TC, TC, FFKM 96467885 YES
105b Shaft Seal/inboard for Back-to-Back OQQE 3/2-36 1 SiC, SiC, EPDM 985200 YES
Shaft Seal/inboard for Back-to-Back OQQV 3/2-36 1 SiC, SiC, FKM 985760 YES
Shaft Seal/inboard for Back-to-Back OUUE 3/2-36 1 TC, TC, EPDM 985189 No
Shaft Seal/inboard for Back-to-Back OUUV 3/2-36 1 TC, TC, FKM 985190 No
107 O-ring for Pos. 105b Back-to-Back 3/2-36 1 EPDM, ø11.5 x 4.3mm 00ID2040 YES
3/2-36 1 FKM, ø11.5 x 4.3mm 00ID2186 YES
O-ring for Pos. 105b Back-to-Back (option) 3/2-36 1 FFKM, ø11.5 x 4.3mm 96440282 No
3/2-36 1 FXM, ø11.5 x 3.18mm 96472618 No
108 Spring for Pos. 105b Back-to-Back 3/2-36 1 12mm 980195 YES
109(a) O-ring for Shaft Seal Pos. 105 3/2-36 1 EPDM, ø21.3 x 3.0mm 00ID1798 YES
3/2-36 1 FKM, ø21.2 x 3.0mm 00ID2339 YES
109b O-ring for Shaft Seal Pos. 105 (option) 3/2-36 1 FXM, ø22 x 2.75mm 96458111 YES
3/2-36 1 FFKM, ø23.47 x 2.62mm 96464384 YES
111 Seal Driver (small) for Pos. 105b Back-to-Back 3/2-36 1 980192 YES
112 Seal Driver (large) for Pos. 105b Back-to-Back 3/2-36 1 980191 YES
112a Seal Drv threaded for 112, Pos. 105b Back-to-Back 3/2-36 1 400203 YES
113 Set Screw for 112a, for Pos. 105b Back-to-Back 3/2-36 1 3mm x M5 x 6mm 00ID7392 YES
146 Allen Bolt for 147/148, for Pos. 105b Back-to-Back 3/2-36 1 2.5mm x M3 x 5mm 96462639 YES
147 Stationary Seal Retainer - Pos. 105b Back-to-Back 3/2-36 1 NV36, 316SS 96457354 No
148 Seal Retainer Washer - Pos. 105b Back-to-Back 3/2-36 1 316SS, ø36.0 x ø21.6 x 5.0mm 96457355 No
Due to part changes over time, all position numbers (1-203) These columns indicates which model uses the spare part. If blank, the part is used in all models.
may not be used.

Notes: Key to Symbols:

^^^ 3/2 to 9 stage= # of Stages less 2 KITS (YES) ....... Recommended spare part
10 to 19 stage= # of stages less 3 Ø ....... Diameter
21 to 27 stage = # of stages less 4 ANSI ....... American National Standards Institute
29 to 36 stage = # of stages less 5 CPL ....... Complete Assembly – these parts consist of more than one component
EPDM ....... Ethylene Propylene (also known as EPR and EPT) – an elastic
^^^^ 3/2 to 9 stage= use 1 substance similar to rubber
10 to 19 stage= use2 FFKM ....... Kalrez Elastomer made by DuPont
21 to 27 stage = use 3 FKM ....... Fluoro Elastomer (generic for Viton)
29 to 36 stage = use 4 FXM ....... Fluoraz Elastomer made by Greene Tweed
M ....... International standard thread size designation (thread diameter in mm)
* Standard use 1. Back-to-Back or Tandem pump version use 3 mm ....... Millimeter
** Standard use 1. Back-to-Back or Tandem pump version use 3 MG ....... Identifies Grundfos motor type/size
*** 1 used in Hxxx (Standard), 2 used in Pxxx (Tandem) pump version N ....... Stainless
NBR ....... Buna - N (also known as Nitrile) – an elastic substance similar to rubber
# stgs- Use the number of stages in standard models, NEMA ....... National Electrical Manufacturers Association
less one in de-staged and Low NPSH models PTFE ....... Teflon
SiC ....... Silicon Carbide
 Standard use 2. Back-to-Back or Tandem pump version use 3 TC ....... Tungsten Carbide
UNC ....... Unified National Coarse – a standard for threads on bolts
 Standard use 2. Back-to-Back or Tandem pump version use 6

6
 Spare Part Kits CR3

Spare Part Kits

Since certain pump parts can be expected to exhibit wear at the same time as related pump parts, they have been grouped into the
following kits for your convenience. The numbers indicate the quantity of the part within each kit. Please order these kits using the
kit material number at the top of the columns.
CR(I, N)1S, 1, & 3 SiC Bearing STACK KITS
WEAR PARTS KIT 2-9 Kit No. 96455095 Model Material Number
WEAR PARTS KIT 10-19 Kit No. 96455092
CR(I)3-3/2 96453529
WEAR PARTS KIT 20-27 Kit No. 96455093
CR(I)3-3 96453530
WEAR PARTS KIT 28-36 Kit No. 96455094
CR(I)3-4 96453531
Pos. No. Description Material No. Qty. Included in each Kit
4a Chamber N Cpl. w/Pos.45 & 65 & SiC Bearing 96439476 1 2 3 4 CR(I)3-5 96453532
39 Gasket for Oval Flange, 95 x 55 x ø35 x 2mm 400189 2 2 2 2 CR(I)3-6 96453533
45 Neck Ring, ø41.3 x ø30.6 x .75mm, PTFE 400003 8 17 24 32 CR(I)3-7 96453534
47a Bearing Ring/Spacer, SiC 150, 13mm 96437488 1 2 3 4 CR(I)3-8 96453535
64a Spacing Pipe, ø15.85 x ø12.85 x 4.5mm 96440292 1 2 3 4 CR(I)3-9 96453536
64c Clamp, Splined, ø15 x ø13.10 x ø10.9 x 13mm 96439668 1 1 1 1 CR(I)3-10 96453537
65 Neck Ring Retainer, N, ø43.5 x ø34.0 x 3.6mm 96438746 8 17 24 32 CR(I)3-11 96453538
66 Lock Washer Set of 2, ø13.5 x ø8.2 x 2.6mm 96417297 1 1 1 1
CR(I)3-12 96453539
67 Lock Nut, 13mm x M8 00ID2061 1 1 1 1
CR(I)3-13 96453540
CR(I)3-15 96453541
CR(I, N )1S, 1, & 3 Graflon Bearing
WEAR PARTS KIT 2-9 Kit No. 96460140 CR(I)3-17 96453542
WEAR PARTS KIT 10-19 Kit No. 96455110 CR(I)3-19 96453543
WEAR PARTS KIT 20-27 Kit No. 96455111 CR(I)3-21 96453544
WEAR PARTS KIT 28-36 Kit No. 96455112 CR(I)3-23 96453545
Pos. No. Description Material No. Qty. Included in each Kit CR(I)3-25 96453546
4a Chamber N Cpl. w/Pos.45 & 65 & Graflon Bearing 96440615 1 2 3 4 CR(I)3-27 96453547
39 Gasket for Oval Flange, 95 x 55 x ø35 x 2mm 400189 2 2 2 2 *** CR(I)3-29 96453548
45 Neck Ring, ø41.3 x ø30.6 x .75mm, PTFE 400003 8 17 24 32 *** CR(I)3-31 96453549
47a Bearing Ring/Spacer, TC, 9.7mm 400041 1 2 3 4
*** CR(I)3-33 96453550
64a Spacing Pipe, ø15.85 x ø12.85 x 7.8mm 400016 1 2 3 4
*** CR(I)3-36 96453551
64c Clamp, Splined, ø15 x ø13.10 x ø10.9 x 13mm 96439668 1 1 1 1
65 Neck Ring Retainer, N, ø43.5 x ø34.0 x 3.6mm 96438746 8 17 24 32
***For 50 Hz operation only.
66 Lock Washer Set of 2, ø13.5 x ø8.2 x 2.6mm 96417297 1 1 1 1
67 Lock Nut, 13mm x M8 00ID2061 1 1 1 1

CR(I )1S, 1, & 3 Bronze Bearing

WEAR PARTS KIT 2-9 Kit No. 96455102
WEAR PARTS KIT 10-19 Kit No. 96455104
WEAR PARTS KIT 20-27 Kit No. 96455105
WEAR PARTS KIT 28-36 Kit No. 96455106
Pos. No. Description Material No. Qty. Included in each Kit
4a Chamber Cpl. w/Pos.45 & 65 & Bronze Bearing 96440612 1 2 3 4
39 Gasket for Oval Flange, 95 x 55 x ø35 x 2mm 400189 2 2 2 2
45 Neck Ring, ø41.3 x ø30.6 x .75mm, PTFE 400003 8 17 24 32
47a Bearing Ring/Spacer, TC, 9.7mm 400041 1 2 3 4
64a Spacing Pipe, ø15.85 x ø12.85 x 7.8mm 400016 1 2 3 4
64c Clamp, Splined, ø15 x ø13.10 x ø10.9 x 13mm 96439668 1 1 1 1
65 Neck Ring Retainer, N, ø43.5 x ø34.0 x 3.6mm 96438746 8 17 24 32
66 Lock Washer Set of 2, ø13.5 x ø8.2 x 2.6mm 96417297 1 1 1 1
67 Lock Nut, 13mm x M8 00ID2061 1 1 1 1

GASKET KIT (EPDM) Kit No. 96455090

GASKET KIT (FKM) Kit No. 96455091
GASKET KIT (FXM) Kit No. 96463944
GASKET KIT (FFKM) Kit No. 96533328
GASKET KIT (EPDM)-Double Seal option. Kit No. 96533362
GASKET KIT (FKM)-Double Seal option. Kit No. 96533363
GASKET KIT (FFKM)-Double Seal option. Kit No. 96533364
Pos. No. Description Material No. Qty. Included in each Kit
37 Sleeve O-ring, EPDM, ø137.5 x 3.3mm 96438743 2 3
Sleeve O-ring, FKM, ø137.5 x 3.3mm 96438744 2 3
37b Sleeve O-ring, FXM, ø137.5 x 3.3mm 96458109 2
Sleeve O-ring, FFKM, ø136.12 x 3.53mm 96466718 2 3
38, 100(a) Drain Plug O-ring, EPDM, Ø16.3 x 2.4mm 00ID1288 3 7
Drain Plug O-ring, FKM, Ø16.3 x 2.4mm 00ID2231 3 7
38, 100a Drain Plug O-ring, FXM, ø16.3 x 2.4mm 96442869 3
Drain Plug O-ring, FFKM, ø16.3 x 2.4mm 96428162 3 7
109(a) O-ring for Pos.105(b) &149, EPDM, Ø21.3 x 3.0mm 00ID1798 1 1
O-ring for Pos.105(b) &149, FKM, Ø21.2 x 3.0mm 00ID2339 1 1
109b O-ring for Pos.105(b) &149, FXM, Ø22.0 x 2.75mm 96458111 1
O-ring for Pos.105(b) &149, FFKM, Ø23.47 x 2.62mm 96464384 1 2

7
Spare Part Kits CR3

Spare Part Kits (continued)

STANDARD SHAFT SEAL KIT, BALANCED CARTRIDGE Kit No. 96455088
(Maximum allowed working PSI is 435) Kit No. 96455089
(Tandem Seal option Pumps require 2 of each Seal Kit) Kit No. 96455086
Kit No. 96455087
Kit No. 96455082
Kit No. 96455083
Kit No. 96455084
Kit No. 96455085
Kit No.
Pos. No. Description Material No. Qty. Included in each Kit
105 HQBE 96441879 1
HQBV 96441880 1
HQQE 96441877 1
HQQV 96441878 1
HUBE 96441873 1
HUBV 96441874 1
HUUE 96441875 1
HUUV 96441876 1
N/A Grinding Device Tool for Emery Cloth 370711 1 1 1 1 1 1 1 1
N/A Emery Cloth 370712 1 1 1 1 1 1 1 1

OPTIONAL SHAFT SEAL KIT, BALANCED CARTRIDGE Kit No. 96491375

(Maximum allowed working PSI is 435) Kit No. 96533327
(Tandem Seal option Pumps require 2 of each Seal Kit) Kit No. 96533326
Kit No. 96533323
Kit No. 96533322
Kit No. 96533325
Kit No. 96533324
Pos. No. Description Material No. Qty. Included in each Kit
105 HQBK 96489537 1
HQQF 96472620 1
HQQK 96498109 1
HUBF 96481464 1
HUBK 96481463 1
HUUF 96475542 1
HUUK 96498108 1
N/A Grinding Device Tool for Emery Cloth 370711 1 1 1 1 1 1 1
N/A Emery Cloth 370712 1 1 1 1 1 1 1

INBOARD SHAFT SEAL & Gasket KIT, Back to Back OQQE Kit No. 96533360
INBOARD SHAFT SEAL & Gasket KIT, Back to Back OQQV Kit No. 96533361
(An HQQx seal kit must also be used for a seal repair)

Pos. No. Description Material No. Qty. Included in each Kit

37 Sleeve O-ring, EPDM, ø137.5 x 3.3mm 96438743 3
Sleeve O-ring, FKM, ø137.5 x 3.3mm 96438744 3
38, 100(a) Drain Plug O-ring, EPDM, Ø16.3 x 2.4mm 00ID1288 7
Drain Plug O-ring, FKM, Ø16.3 x 2.4mm 00ID2231 7
102 O-ring, EPDM, ø18 x 2.5mm 00ID2041 1
O-ring, FKM, ø17.86 x 2.62mm 00ID2187 1
103 Stationary Seal Ring, SiC,12mm 980746 1
104 Rotating Seal Ring, SiC, 12mm 980733 1 1
107 O-ring, EPDM, ø11.5 x 4.3mm 00ID2040 1
O-ring, FKM, ø11.5 x 4.3mm 00ID2186 1
108 Spring, 12mm 980195 1 1
109a O-ring, EPDM, ø21.3 x 3.0mm 00ID1798 1
O-ring, FKM, ø21.2 x 3.0mm 00ID2339 1
111 Driver for pos.104 980192 1 1
112 Driver for pos.111 980191 1 1
112a Driver for pos.112 400203 1 1
113 Set Screw for pos.112a 00ID7392 2 2
146 Allen Bolt for pos.147 & 148, 2.5mm x M3 x 5mm 96462639 3 3

IEC COUPLING KIT

ø14/ø12 Kit No. 415060
ø19/ø12 Kit No. 415061
ø24/ø12 Kit No. 415062
ø28/ø12 Kit No. 415063
ø38/ø12 Kit No. 415065
Pos. No. Description Material No. Qty. Included in each Kit
9 Allen Screw, M6 x 20mm, Delta Seal 00ID7899 4
Allen Screw, M8 x 25mm, Delta Seal 00ID7900 4 4 4
Allen Screw, M10 x 25mm, Delta Seal 00ID7901 4
10 Shaft Pin, ø5 x 26mm, Stainless 310192 1 1 1 1 1
10a Coupling Half, F85, MG71, .37-.55kW. ø14/ø12 410041 2
Coupling Half, F100, MG80,.75-1.1kW. ø19/ø12 410043 2
Coupling Half, F115, MG 90, 1.5-2.2kW. ø24/ø12 410045 2
Coupling Half, F130, MG100/112, 3-4 kW.ø28/ø12 410047 2
Coupling Half, F265, MG132, 5.5-7.5kW. ø38/ø12 410115 2

8
 Spare Part Kits • Accessories CR3

Spare Part Kits (continued)

NEMA COUPLING KIT
ø15.8/ø12 Kit No. 415314
ø28.5/ø12 Kit No. 415315
ø34.9/ø12 Kit No. 96478700
Pos. No. Description Material No. Qty. Included in each Kit
9 Allen Screw, M6 x 20mm, Delta Seal 00ID7899 4
Allen Screw, M8 x 25mm, Delta Seal 00ID7900 4 4
Allen Screw, M10 x 25mm, Delta Seal 00ID7901
10 Shaft Pin, ø5 x 26mm, Stainless 310192 1 1 1
10a Coupling Half, 56C, 1/3 - 2HP. ø15.8 / ø12 410108 2
Coupling Half, 182/184TC, 3-5HP. ø28.5/ø12 410109 2
Coupling Half, 213TC, 7.5-10HP. ø34.9/ø12 96472175 2

OVAL FLANGE KIT FOR SMALL CR1S, 1, & 3

1" Threaded Cast Iron ( 232 PSI Max.) Kit No. 96474336
Pos. No. Description Material No. Qty. Included in each Kit
12 Flange, Cast Iron, 1" - 11.5 NPT 96468333 2
35 Hex Head Bolt, M10 x 40mm, Delta Seal 00ID8027 4
39 Gasket , 95 x 55 x ø35 x 2mm, KLINGERSIL C4430 400189 2

Accessories
Accessories
ANSI COMPANION FLANGES FOR SMALL CR
1-1/4" Threaded Cast Iron, 250 Lb. Class Kit No. 91122260
Pos. No. Description Material No. Qty. Included in each Kit
N/A Nut, HEX 5/8"-11 UNC, Grade 2 00ID1510 8
N/A Plain Bolt, 5/8" x 2-1/2", Grade 2 00ID1920 8
N/A Flange, Cast Iron, 1-1/4" 00ID3650 2
N/A Gasket Full Face Flange, 1-1/4", 300#, Cut Ring 400201 2

9
Spare Part Kits • Special Tools CR3

Special Tools
Tools not generally available from normal sources.
Mat. No. Description and Use

00SV0040 Shaft Holder for Dismantling/Assembly

Used to hold and protect the shaft during dismantling and assembly.

00SV2007 Tubular Box Spanner for Shaft Seal 36.1 mm

Used to install and remove the shaft seal.
Fits a 1/2” drive ratchet.

00SV0239 Puller for Neck Ring

Used to remove the Neck Ring from Chamber.

00SV2014 Circlip Pliers for Flange Lock Ring

Used to remove the Lock Ring for the Flange.

00SV2066 Tool for Outer Sleeve

Used to press sleeve into base. (optional)

00SV2011 Bit Holder

Used with Bits Kit, 1/4”

00SV2010 Bits Kit

NV 5 mm for M6, 1/4”
NV 6 mm for M8, 1/4”
NV 8 mm for M10, 1/4”

00SV2012 Hexagon Socket Bit

Used for Shaft Seal
NV 2.5 mm for M5, 1/4”

Standard Tools
In addition to being available from Grundfos, comparable tools can be purchased through normal sources.
Mat. No. Description and Use
Wrenches
Used to tighten various nuts.
00SV0083 NV 10 mm for M6
00SV0055 NV 13 mm for M8
00SV0056 NV 17 mm for M10
00SV0054 NV 19 mm for M12
00SV0122 NV 24 mm for M16

Torque Wrench
Used to torque various screws.
00SV0292 4-20 Nm, 9 x 12
00SV0269 20-100 Nm, 9 x 12
00SV0400 40-200 Nm, 14x18

Torque Screwdriver
Used to tighten various nuts.
00SV0438 1-6 Nm, 1/4”

Ratchet Spanner for all Adapters

00SV0295 9 mm x 12 mm, 1/2”

Socket Spanner with Inside Hex

00SV0296 NV 5 mm for M6, 1/2” x 1/2”
00SV0297 NV 6 mm for M8, 1/2” x 1/2”
00SV0298 NV 8 mm for M10, 1/2” x 1/2”

Ring Spanner
00SV0310 NV 10 mm for M6
00SV0294 NV 13 mm for M8
00SV0270 NV 17 mm for M10
00SV0271 NV 19 mm for M12
00SV0524 NV 24 mm for M16

Socket Spanner
00SV2013 NV 13 mm for M8, 9 x 12

10
L-CR-SM-026 0504
The name Grundfos, the Grundfos logo, and be think innovate are registered trademarks owned by Grundfos Holding A/S, Denmark. All rights reserved worldwide. © Copyright Grundfos Holding A/S

GRUNDFOS Pumps Corporation GRUNDFOS Canada, Inc. Bombas GRUNDFOS de Mexico S.A. de C.V.
17100 W. 118th Terrace 2941 Brighton Road Boulevard TLC No. 15
Olathe, Kansas 66062 Oakville, Ontario L6H 6C9 Canada Parque Industrial Stiva Aeropuerto
Phone: 913.227.3400 Phone: 905.829.9533 Apodaca, N.L. Mexico 66600
Fax: 913.227.3500 Fax: 905.829.9512 Phone: 52.81.8144.4000
Fax: 52.81.8144.4010
www.grundfos.us