Technical data HS 875 HD

Hydraulic crawler crane

 Dimensions
Basic machine with undercarriage

R5
710

8300 3500
2580

4020
2110

1300

1240
1400 2600

530
5330 1000
6480 2240 4900

520
R5

14100

Operating weight Remarks

The operating weight includes the basic machine with HD under- 1. The lifting capacities stated are valid for lifting operation only
carriage, 2 main winches 250 kN with speed change gear and (corresponding with crane classification according to F.E.M.
11 m boom, consisting of A–frame, boom foot (4 m), boom head 1.001. crane group A1).
section (6.4 m), boom head (0.6 m) and 19.6 t basic counterweight +
4.5 t add. counterweight. 2. Crane standing on firm, horizontal ground.

Total weight approx. 93 t 3. The weight of the lifting device (hoisting ropes, hook block,
shackle etc.) must be deducted form the gross lifting capacity to
obtain a net lifting value.
Ground pressure 4. Additional equipment on boom (e.g. boom walkways, auxiliary jib)
2
must be deducted to get the net lifting capacity.
Ground bearing pressure 0.87 kg/cm
5. For max. wind speed please refer to lift chart in operator‘s cab
or manual.
Equipment 6. Working radii are measured from center of swing and under load.
Main boom max. length 50 m 7. The lifting capacities are valid for 360 degrees of swing.
Universal boom head with interchangeable rope pulleys.
Modular designed equipment for operation as crane, with dragline or 8. Calculation of stability under load is based on DIN 15019 / part 2 /
clamshell. chart 1 and ISO 4305 Table 1 + 2, tipping angle 4°.
For dragline operation, a rotating fairlead is fitted into the boom foot.
This minimizes the rope angle to drum, which results in lower rope 9. The structures are calculated according to F.E.M. 1.001 - 1998
wear. (EN 13001-1; EN 13001-2).

2 HS 875 HD
 Transport dimensions and weights
Basic machine and boom (No. 1313.xx)

Basic machine
with HD undercarriage, 2 x 250 kN winches with change gear box, without
3200 counterweight, boom foot and A–frame
3-web grousers 1000 mm
Width 3980 mm
Weight 63600 kg
1000 1980
530
8420 3980

1520 A–frame
Width 600 mm
5780 Weight 2195 kg

1510 Boom foot (No. 1313.xx)

Width 1470 mm
4250 Weight 2070 kg

1550
Boom section (No. 1313.xx) 3 m
Width 1430 mm
3150
Weight* 725 kg

1550
Boom section (No. 1313.xx) 6 m
6150 Width 1430 mm
Weight* 1125 kg

1550

Boom section (No. 1313.xx) 12 m

12150
Width 1430 mm
Weight* 1955 kg

1430

6530
Boom head section (No. 1313.xx) 6.4 m
Width 1430 mm
Weight* 1050 kg

1210
1820
Boom head 1) (No. 1313.xx) B A
2700 2820 Width 850 mm 850 mm
Weight* 1840 kg 1800 kg
*) Including pendant ropes 1) Steel sheaves

HS 875 HD 3
 Transport dimensions and weights
Counterweight

Basic counterweight 1x
Width 820 mm
Weight 19600 kg
875 2200

Additional counterweight 1x
3200 Width 670 mm
Weight 4500 kg

585

3200

Hooks

100 t hook block - 2 sheaves

Width 320 mm
1150
Weight* 1200 kg

1910
50 t hook block - 1 sheave
900 Width 300 mm
Weight* 750 kg
1800

25 t single hook
820 400 Width 400 mm
Weight* 400 kg

4 HS 875 HD
 Technical description

Engine Main winches

Power rating according to ISO 9249, 450 kW (603 hp) at 1900 rpm Winch options:
Engine type Liebherr D 9508 A7 Line pull (nom. load) 200 kN 250 kN 300 kN
Fuel tank 920 l capacity with continuous level Rope diameter 30 mm 34 mm 36 mm
indicator and reserve warning Drum diameter 630 mm 750 mm 820 mm
Engine complies with NRMM exhaust certification EPA/CARB Tier 3 Rope speed 0–86 m/min 0-69 m/min 0-55 m/min
and 97/68 EC Stage III. With change gear box 0-123 m/min 0-119 m/min
Option: Rope capacity 1st layer 40.5 m 38.9 m 38.6 m
Power rating according to ISO 3046 IFN, 670 kW (898 hp) at 1900 rpm The winches are outstanding in their compact design and easy
Engine type MAN D 2842 LE assembly. Clutch and braking functions on the free fall system are
Fuel tank 920 l capacity with continuous level provided by a compact designed, low wear and maintenance-free
indicator and reserve warning multi–disc brake. The drag and hoist winches use pressure controlled,
Engine complies with NRMM exhaust certification EPA / CARB Tier 2. variable flow hydraulic motors. This system features sensors that
automatically adjust oil flow to provide max. winch speed depending
on load.
Option:
Crane winch (main winch) 160 kN with multi-disc holding brake
Auxiliary winch 70 kN in boom foot
Hydraulic system Tagline winch 30 kN with free fall

The main pumps are operated by a distributor gearbox. Axial piston

displacement pumps work in closed and open circuits supplying
oil only when needed (flow control on demand). To minimize peak
pressure an automatically working pressure cut-off is integrated.
This spares pumps and saves energy. The hydraulic oil is cleaned
through electronically controlled pressure and return filters.
Possible contamination is signaled in the cabin. The use of synthetic Crawlers
environmentally friendly oils is possible. Ready made hydraulic retrofit
kits are available to customize requirements e.g. powering casing The track width of the undercarriage is changed hydraulically.
oscillators, VM–vibrators, hydraulic grabs, fixed leaders etc. Propulsion through axial piston motor, hydraulically released spring
Working pressure max. 350 bar loaded multi–disc brake, maintenance-free crawler tracks, hydraulic
Oil tank capacity 1170 l chain tensioning device.
3-web grousers 1000 mm
Drive speed 0 – 1.15 km/h
Option:
s¬  SPEED¬HYDRAULIC¬MOTOR¬FOR¬HIGHER¬TRAVEL¬SPEED

Boom winch
Line pull max. 2x 70 kN
Rope diameter 20 mm
Boom up 84 sec. from 15° to 82°

Control
The control system – developed and manufactured by Liebherr – is
designed to withstand extreme temperature changes and the rough
Swing heavy duty tasks common in the construction industry. Complete
machine operating data are shown on a high resolution display. The
Consists of rollerbearing with external teeth for lower tooth flank crane is equipped with proportional control for all movements, which
pressure, fixed axial piston hydraulic motor, spring loaded and can be carried out simultaneously.
hydraulically released multi–disc holding brake, planetary gearbox and Dragline operation: A special ”Interlock” control system is an option
pinion. Swing speed from 0 – 3.5 rpm continuously variable, selector available. It is designed for power lifting of the dragline bucket without
for 3 speed ranges to increase swing precision. using the drag winch brake.
Option: On request, Liebherr also offers special custom designed control
Second swing drive systems for free fall winches.
Operation:
Left joy stick for boom winch and swing, right two directional levers
for winch I and II. Crawler control is actuated with the two central foot
pedals. Additionally, hand levers can be attached to the pedals.
Options:
Noise emission s¬ 3PECIAL¬DEMOLITION¬CONTROL¬SYSTEM
s¬ -$%¬-ACHINE¬DATA¬RECORDING
Noise emissions correspond with 2000/14/EC directive on noise s¬ 0$%¬0ROCESS¬DATA¬RECORDING
emission by equipment used outdoors. s¬ '3-¬MODEM

HS 875 HD 5
 Equipment (main boom No. 1313.xx and 24.1 t counterweight)
Casing oscillator and slurry wall grab

Casing oscillator* Slurry wall grab*

Winch options 2 x 250 kN 2 x 300 kN Winch options 2 x 250 kN 2 x 300 kN
Line speed 1st gear (m/min) 0-69 0-55 Line speed 1st gear (m/min) 0-69 0-55
Line speed 2nd gear (m/min) 0-123 0-119 Line speed 2nd gear (m/min) 0-123 0-119
Drilling diameter 2500 mm 2500 mm Max. chisel weight 16 t 25 t

*) Load chart for duty cycle operation see page 8

6 HS 875 HD
Equipment (main boom No. 1313.xx and 24.1 t counterweight)
Dynamic soil compaction

Capacities in metric tons for boom lengths (21 m - 33 m)

Boom length
Radius (m) 21 m 24 m 27 m 30 m 33 m
t t t t t
8 25 25 20 20 19
9 20 19 19 18 17

Max. capacities in metric tons do not exceed 75% of tipping load.

All loads given are max. values and must not be exceeded. They are
only permitted in two-rope automatic operation and are valid for work
on a surface with max. inclination of 1%. Lifting heights shall not
exceed 25 m.

HS 875 HD 7
 Load chart for duty cycle operation (main boom No. 1313.xx)
24.1 t counterweight

Capacities in metric tons for boom lengths (12 m - 33 m) - with 300 kN winches
Boom length (m)
Radius 12 15 18 21 24 27 30 33 Radius
(m) t t t t t t t t (m)
5 46.2 5
6 46.2 46.0 43.5 38.1 32.7 28.8 25.8 23.4 6
7 43.6 42.0 39.6 35.2 31.2 28.5 25.8 23.4 7
8 35.9 34.5 33.2 31.9 29.6 27.1 25.0 23.3 8
9 30.3 29.6 29.0 28.3 27.1 26.1 23.8 22.2 9
10 27.0 26.5 26.0 25.3 24.7 23.7 23.0 21.2 10
12 22.3 21.8 21.3 20.8 20.4 19.8 19.3 18.5 12
14 18.4 18.1 17.6 17.3 16.8 16.3 15.8 14
16 15.4 15.2 14.9 14.4 14.0 13.6 16
18 12.9 12.9 12.9 12.6 12.2 11.8 18
20 11.0 11.1 11.0 10.7 10.3 20
22 9.5 9.5 9.4 9.0 22
24 8.1 8.1 7.8 24
26 6.9 6.9 6.8 26
28 6.0 5.9 28
30 5.1 30
32 4.3 32
TLT 10532870 M00000 Vorab3

Maximum capacity in duty cycle operation with standard ropes 1) Lifting a load exceeding the line pull of one winch is only allowed
if it can be ensured that each individual winch is not overloaded.
Line pull kN 200 250 300 When working with a mechanical 2-rope grab the total load
to be lifted is limited by the line pull of one winch.
Rope diameter mm 30 34 36 Rigging and ropes are part of the load.
Minimum breaking load kN 846 1046 1186
2) Max. capacities in metric tons do not exceed 75% of tipping load.
Line pull - 1-rope duty cycle operation t 20 25 30 Crane standing on firm, horizontal ground.
Line pull - 2-rope duty cycle operation 1) t 30.3 37.9 46.2

Capacities in duty cycle operation are for reference only and are not programmed in the LMI system.
All loads and counterweight configurations are max. values and must not be exceeded.
Weight of additional equipment on boom (e.g. walkways, hose drums etc.) must be deducted to get the net capacity.

8 HS 875 HD
Dragline equipment (main boom No. 1313.xx)
24.1 t counterweight

Capacities in metric tons for boom lengths (15 m - 30 m) counterweight 24.1 t

Boom length (m)
C 15 18 21 24 27 30
alpha C J C J C J C J C J C J
(m) (m) t (m) (m) t (m) (m) t (m) (m) t (m) (m) t (m) (m) t
K 45 12.7 12.7 20.7 14.8 14.8 17.1 16.9 16.9 14.1 19.0 19.1 11.9 21.1 21.2 10.1 23.3 23.3 8.5
J 40 13.5 11.7 19.2 15.8 13.7 15.6 18.1 15.6 12.8 20.4 17.5 10.7 22.7 19.4 9.0 25.0 21.4 7.5
35 14.3 10.7 17.9 16.8 12.4 14.4 19.3 14.1 11.7 21.7 15.9 9.8 24.2 17.6 8.0 26.6 19.3 6.6
30 15.0 9.6 16.7 17.6 11.1 13.4 20.2 12.6 10.8 22.8 14.1 8.8 25.4 15.6 7.2 28.0 17.1 5.9
25 15.6 8.4 15.7 18.4 9.7 12.4 21.1 11.0 9.8 23.8 12.2 8.1 26.5 13.5 6.6 29.2 14.8 5.4
TLT 10532870 M00000 Vorab3
E D
Max. capacities in metric tons do not exceed 75% of tipping load.
Capacities in duty cycle operation are for reference only and are not programmed in the LMI system.
The size of the bucket has to be determined according to local conditions.

Digging diagram
C = Radius / dumping radius
D = Max. digging radius = approx.
C + 1/3 to 1/2 J - K
E = Digging depth = approx.
40 - 50% of C
J = Height to centre rope pulley
boom head
K = Length of dragline bucket
(according to manufacturer‘s
specification)

Clamshell equipment (main boom No. 1313.xx)

24.1 t counterweight

Capacities in metric tons for boom lengths (15 m - 30 m) counterweight 24.1 t

C Boom length (m)
15 18 21 24 27 30
alpha C J C J C J C J C J C J
1500
(m) (m) t (m) (m) t (m) (m) t (m) (m) t (m) (m) t (m) (m) t
K 65 8.4 15.7 30.9 9.7 18.4 26.0 10.9 21.1 22.0 12.2 23.8 18.9 13.5 26.6 16.4 14.7 29.3 14.3
60 9.5 15.1 26.6 11.0 17.7 21.8 12.5 20.3 18.2 14.0 22.9 15.5 15.5 25.5 13.4 17.0 28.1 11.7
55 10.7 14.4 22.9 12.4 16.8 18.7 14.1 19.3 15.5 15.8 21.8 13.2 17.5 24.2 11.3 19.3 26.7 9.8
J 50 11.7 13.6 20.2 13.6 15.9 16.4 15.5 18.2 13.6 17.5 20.5 11.5 19.4 22.8 9.8 21.3 25.1 8.4
45 12.7 12.7 18.1 14.8 14.8 14.6 16.9 16.9 12.1 19.0 19.1 10.2 21.1 21.2 8.6 23.3 23.3 7.3
40 13.5 11.7 16.5 15.8 13.7 13.3 18.1 15.6 10.9 20.4 17.5 9.2 22.7 19.4 7.7 25.0 21.4 6.5
35 14.3 10.7 15.2 16.8 12.4 12.3 19.3 14.1 10.0 21.7 15.9 8.4 24.2 17.6 7.0 26.6 19.3 5.9
30 15.0 9.6 14.3 17.6 11.1 11.4 20.2 12.6 9.3 22.8 14.1 7.8 25.4 15.6 6.5 28.0 17.1 5.4
25 15.6 8.4 13.5 18.4 9.7 10.8 21.1 11.0 8.8 23.8 12.2 7.3 26.5 13.5 6.0 29.2 14.8 5.0
TLT 10538307 M00000 Vorab4

Max. capacities in metric tons do not exceed 66.7% of tipping load.

Working diagram Capacities in duty cycle operation are for reference only and are not programmed in the LMI system.
C = Radius / dumping radius
J = Height of boom head sheave centre
above ground level
K = Length of clamshell (depending on
type and capacity of bucket)

HS 875 HD 9
 Working range - main boom 82° – 15°
24.1 t counterweight

Auxiliary jib 25 t

2000

The maximum capacity

of the auxiliary jib is 25 t.
The corresponding load
chart is programmed in
the LMI system.

Main boom configuration (No. 1313.xx)

Configuration for boom lengths (11 m - 50 m)
Length Amount of boom extensions
Boom foot 4.0 m 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Boom section 3.0 m 1 1 1 1 1 1 1
Boom section 6.0 m 1 1 1 1 1 1
Boom section 12.0 m 1 1 1 1 2 2 2 2 3 3
Boom head section 6.4 m 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Boom head 0.6 m 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Boom length (m) 11 14 17 20 23 26 29 32 35 38 41 44 47 50

10 HS 875 HD
 Load chart for lift crane operation (No. 1313.xx)
24.1 t counterweight

Capacities in metric tons for boom lengths (11 m - 50 m) - with 300 kN winches
Boom length (m)
Radius 11 14 17 20 23 26 29 32 35 38 41 44 47 50 Radius
(m) t t t t t t t t t t t t t t (m)
3.8 100.0 3.8
4 100.0 4
5 89.0 88.0 85.7 5
6 65.7 65.8 65.8 64.3 62.8 61.3 6
7 51.8 51.8 51.9 51.8 51.0 49.9 48.9 47.8 7
8 42.5 42.6 42.6 42.5 42.5 42.0 41.1 40.2 39.3 38.4 37.2 8
9 35.9 36.0 36.0 35.9 35.8 35.7 35.3 34.6 33.8 33.1 32.3 31.5 29.2 9
10 30.9 31.0 31.0 30.9 30.9 30.7 30.6 30.2 29.6 28.9 28.2 27.5 26.8 25.5 10
12 23.8 24.0 24.1 24.0 23.9 23.8 23.7 23.5 23.4 23.0 22.5 21.9 21.3 20.7 12
14 19.5 19.6 19.5 19.4 19.3 19.2 19.0 18.9 18.7 18.3 17.8 17.3 16.8 14
16 16.2 16.1 16.1 16.0 15.8 15.7 15.5 15.4 15.2 14.8 14.4 13.9 16
18 13.6 13.6 13.6 13.5 13.3 13.2 13.0 12.8 12.7 12.5 12.1 11.7 18
20 11.6 11.6 11.5 11.4 11.2 11.1 10.9 10.7 10.5 10.3 9.9 20
22 10.0 9.9 9.8 9.6 9.5 9.3 9.2 9.0 8.8 8.5 22
24 8.7 8.6 8.5 8.3 8.2 8.0 7.9 7.7 7.5 7.3 24
26 7.5 7.4 7.3 7.2 7.0 6.8 6.6 6.4 6.2 26
28 6.5 6.3 6.2 6.1 5.9 5.7 5.5 5.3 28
30 5.7 5.6 5.5 5.3 5.1 4.9 4.7 4.5 30
32 4.8 4.8 4.6 4.4 4.2 4.1 3.9 32
34 4.2 4.0 3.8 3.6 3.5 3.3 34
36 3.4 3.3 3.1 2.9 2.7 36
38 3.0 2.8 2.6 2.5 2.3 38
40 2.2 2.2 2.0 1.8 40
42 1.8 1.7 1.5 42
44 1.4 1.3 1.1 44
TLT 984261614 M 00000

Above load chart is for reference only. For actual lift duty please refer to load chart in operator’s cab or manual.

HS 875 HD 11
 HS 875 HD – 10223485 – 03/2010 Subject to change without notice.

Liebherr-Werk Nenzing GmbH

P.O. Box 10, A-6710 Nenzing/Austria
Tel.: +43 50809 41–473
Fax: +43 50809 41–499
[email protected]
www.liebherr.com