Scribd
Upload
85 views

The Design Is Adequate.: Rectangular Section Member Design Based On AISC 360-10/16 Input Data & Design Summary

This document summarizes the design of a rectangular steel member according to AISC 360-10/16. It provides the member dimensions, applied loads, and design checks for bending, compression, combined loading, and shear. All capacity checks show the member is adequate for the given loads.

Uploaded by

Sureshbabu Narayanasamy
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
85 views

The Design Is Adequate.: Rectangular Section Member Design Based On AISC 360-10/16 Input Data & Design Summary

This document summarizes the design of a rectangular steel member according to AISC 360-10/16. It provides the member dimensions, applied loads, and design checks for bending, compression, combined loading, and shear. All capacity checks show the member is adequate for the given loads.

Uploaded by

Sureshbabu Narayanasamy
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
You are on page 1/ 1

PROJECT : PAGE :

CLIENT : DESIGN BY :
JOB NO. : DATE : REVIEW BY :
Rectangular Section Member Design Based on AISC 360-10/16

INPUT DATA & DESIGN SUMMARY


STEEL YIELD STRESS Fy = 36 ksi, (248 MPa)
SECTION DIMENSIONS t = 0.375 in, (10 mm)
d = 15.5 in, (394 mm)

STRONG AXIS, x-x, UNBRACED BENDING LENGTH Lb = 1.06 ft, (0.32 m)


STRONG AXIS, x-x, UNBRACED AXIAL LENGTH Lc,x = KLx = 2.12 ft, (0.65 m)
WEAK AXIS, y-y, UNBRACED AXIAL LENGTH Lc,y = KLy = 2.12 ft, (0.65 m)

AXIAL LOAD, ASD P= 0.69 kips, (3 kN)


STRONG AXIS, x-x, BENDING LOAD, ASD Mx = 2.6 ft-kips, (4 kN-m)
WEAK AXIS, y-y, BENDING LOAD, ASD My = 0 ft-kips, (0 kN-m)
STRONG DIRECTION SHEAR LOAD, ASD V= 0.93 kips, (4 kN)

THE DESIGN IS ADEQUATE.

ANALYSIS
CHECK BENDING CAPACITY (AISC 360 F11)

 Lbd  0.08E
 M p , for
 t2 Fy
1 
    L bd  F y   0.08 E d 1.9 E 28.1 ft-kips > Mx
Mn   L b2 
 Min  C b 1.52  0.274  2   M y , M p , for 
b  b     t  E   Fy t Fy
 d 1.9 E [Satisfactory]
 Min  F cr S x , M p  , for L b2 

 t Fy

Where Mp = Min( Fy Z , 1.6 My ) = 67.6 ft-kips Cb = 1.0 , (AISC 360 F1)


Z = t d2/ 4 = 22.5 in3 Sx = t d2/ 6 = 15.0 in3
My = Fy t d2/ 6 = 45.0 ft-kips Wb = 1.67 , (AISC 360 F1)
Fcr = Min[1.9 E Cb t2 / (d Lb ) , Fy] = 36.0 ksi E= 29000 ksi

CHECK COMPRESSION CAPACITY (AISC 360-16 E7)

 KL E
  0.658 F y F e  F y , for
/  4.71 or F e  0.44 F y
P n  Ae  r Fy 13.1 kips > P
 
 c c  KL E
0.877 F e , for  4.71 and F e  0.44 F y [Satisfactory]
 r F y

Where Lc / r = 120.5 Max( Lc,x / d , Lc,y / t) = 235.0 Wc = 1.67 , (AISC 360 E1)
Fe = p2 E / (Lc / r)2 = 5.18 ksi be = 12.8 in
lr = 10.75 c1 = 0.22 c2 = 1.49 Ae = 4.8 in2
Fel = 5.40 ksi Fcr = 4.55 ksi

CHECK COMBINED COMPRESSION AND BENDING CAPACITY (AISC 360 H1)

 P r 8  M rx M ry  P r  0.2
     , for 0.12 < 1.0 [Satisfactory]
 P c 9  M cx M cy  Pc
 
 P r  M rx M ry  P r  0.2
    , for

 2 P c  M cx M cy  Pc
Where Pr = 0.7 kips Pc = Pn / W c = 13.1 kips, (AISC 360 Chapter E)
Mrx = 2.6 ft-kips Mcx = Mn / Wb = 28.1 ft-kips, (AISC 360 Chapter F)
Mry = 0.0 ft-kips < Mcy = Mn / Wb = 27.0 ft-kips, (AISC 360 Chapter F)

CHECK SHEAR CAPACITY (AISC 360 G2)


Vny / Wv = 139.8 / 1.67 = 83.7 kips > V= 0.9 kips [Satisfactory]

You might also like