Terlotherm® Delta series

Scraped surface heat exchanger

Why a Terlotherm® scraped surface heat exchanger?
Many prepared foods and other products prevent an even temperature distribution is ensured by a rotor
optimal heat transfer because of their consistency. and blade assembly, which continuously and gently
For example, food containing large particles, viscous, blends the product, while simultaneously removing it
sticky and crystalline products can quickly block or from the heat transfer surface.
foul certain types of heat exchangers. The Terlotherm® is a vertical scraped surface heat
Scraped surface heat exchangers incorporate special exchanger with two concentric heat exchange cylin-
design features which make them ideal for heating ders to provide optimum heat transfer. This design,
and cooling products that impair good heat transfer. together with other features, offers the following
As the product is pumped through the SSHE cylinder, advantages:
 Vertical unit, which gives a large heat exchange The Terlotherm® operates, utilizing low pressures
surface area but covers a small footprint saving and a low rpm, but still maintains the same tip
valuable production floor space area. Our largest speeds of the scraper blades as other units that
machine saves more than 7 times the surface area run at much higher rpm and pressures. This is due
than conventional equipment. to our unique design of the double wall cylinder.
This is a key advantage for very sensitive or
One mechanical seal construction. All other types complex products that can be easily damaged with
of equipment have a minimum of two seals and too much pressure or too high rpm.
require a lot of time to replace the seals. The seal
in the Terlotherm® can be changed very quickly. Due to the modular building design the heat
No special hydraulic system is required as it is with exchange capacity can be increased by exchanging
other conventional equipment. only the cylinders for larger ones instead of the
complete machine.
Simple inspection of the interior of the machine via
the top lid, which can be opened without special Efficient heat transfer is achieved by continuous
tools. There is no need to disturb the seal or pull scraping of the entire heat exchange surface.
the shaft while replacing the scrapers.
The Terlotherm® has been approved with USDA,
For maintenance purposes the equipment is easily U-Stamp, PED, ASME codes and the Chinese
accessible and simple to clean. Pressure Vessel Directive.

Both the inner and outer cylinder can be disman- High food safety with the availability of X-ray and
tled for refurbishment or replacement. metal detectable scrapers and seals.

All product contacting parts are FDA approved

material.

The heat exchange surfaces are not provided with

potentially dangerous materials such as chromium
or other materials, but are of solid high quality
stainless steel, thus avoiding the danger or con-
tamination of the product.
Products and processes
TYPICAL PRODUCTS PROCESSED BY THE TERLOTHERM®:

SAUCES & CONDIMENTS: CONFECTIONARY:

Mayonnaise Caramel
Ketchup Chocolate
Starch paste Compounds
BBQ sauce Wafer cream
Mustard Fondant
Alfredo sauce Jelly
Cranberry sauce Fudge
Marinara sauce Marshmallow
Gravies Waffle batter
Cheese sauce Icing
Tartar sauce Syrup
Salad dressing Crème patisserie
Chili
Hummus
Salsa FRUIT:
Tapenade
Olive paste Aseptic fruit
Fruit preps
Marmalade
DAIRY: Chutney
Apple sauce
Pudding Pie filling
WPC Smoothie
MPC
Yoghurt
Quark MEAT PRODUCTS:
Dairy creamer
Ice cream mix Taco filling
Cream cheese MDM
Pet food

PERSONAL CARE:
GENERAL:
Ointments
Lotions Peanut butter
Gels Potato mash
Vaseline Egg
Waxes
CONTINUOUS HTST PASTEURIZATION HEATING AND COOLING LINE

WAX, EMULSION COOLING CRYSTALLIZATION LINE

The Terlotherm® can handle particles up to 1 inch.

1 inch

Terlotherm® advantages and applications

ADVANTAGES Product outlet

Product outletProduct outlet

Scrapers can easily be replaced without tools

Can be CIP cleaned and SIP sterilized
Product area inspection without removing seal
Lid can be opened with quick clamp system
Large heat exchange area with small footprint Inlet
Inlet Inlet
(outer jacket) (outer jacket)
(outer jacket)
Tangential inlet
Acceleration and deceleration area
No damage to product
Maintenance-friendly; only one seal and one drive
Exchangeable cylinders
Outlet Outlet Outlet
Metal detectable scrapers and seals available (outer jacket) (outer jacket)
(outer jacket)

APPLICATIONS Outlet Outlet Outlet

(inner jacket) (inner jacket)
(inner jacket) Inlet
Inlet
Inlet
(inner jacket) (inner jacket)

Heating (inner jacket)

Product
Product Product
Aseptic cooling inlet
inlet
inlet

Deep-cooling
Crystallization
Sterilization
Pasteurization
Gelling
Terlotherm® modules and system integration
An increasing amount of customers are preferring the heating or cooling with local automation, up to a
Terlotherm® as a turn key module or system above complex pasteurization/holding/cooling system
using it as only as a component. With our process controlled via a central automation system in the
knowledge and manufacturing capabilities Terlet can factory. For these, and other solutions, Terlet is your
design such a turn key solution in a great variety of reliable partner.
configurations. From a simple stand alone machine for

Terlotherm® Laboratorium skid

R&D purposes
Small batch sizes
50–100 l/h
Inline heating and cooling
Optional modular product holding section for
variable time temperature combination
Data login system for storing all necessary test
parameters

Terlotherm® scrapers & seals

The scraper blades and the seals can be supplied with
a high quality X-ray and metal detectable material,
which is tasteless, non-toxic and contains no undesir-
able reinforcing material such as glass fibers, etc.
The chemical resistance is very high, were as the
water absorption is extremely low. Bacteriologically
this synthetic material is inert.
 Number of scrapers

Maximum pressure

Maximum pressure
Scraper peripheral

outer cylinder inch

outer cylinder inch

inner cylinder inch

inner cylinder inch

Product outlet NW

medium area barg

product area barg
Product inlet NW

Cooling medium
Annular product

Total height mm
surface area m2
Heat exchange

Medium outlet

Medium outlet

flow rate m3/h

Medium inlet

Medium inlet
Terlotherm®

Footprint m2

velocity m/s
space mm
model

Delta 0.3 30 925 0.5 16 0.5-3.0 25 25 ½ ½ ½ ½ 10 4 2

Lab

Delta 0.5 50 1250 1.0 8 0.5-3.0 65 65 1 1½ 1 1½ 10 6 8

50

Delta 1.0 50 1567 1.0 16 0.5-3.0 65 65 1 1½ 1 1½ 10 6 8

100

Delta 1.5 50 2057 1.0 24 0.5-3.0 65 65 1 1½ 1 1½ 10 6 12

150

Delta 2.0 50 2379 1.0 32 0.5-3.0 65 65 1 1½ 1 1½ 10 6 15

200

Delta 4.5 50 2536 1.4 48 0.5-3.0 80 80 1½ 2 1½ 2 10 6 30

450

Delta 7.0 50 3205 1.4 84 0.5-3.0 80 80 2 3 2 3 10 6 35

700

Delta 50 Delta 100 Delta 150 Delta 200 Delta 450 Delta 700

Terlet B.V.
Oostzeestraat 6
NL-7202 CM Zutphen
THE NETHERLANDS
phone +31 575 593-100
fax +31 575 593-111
[email protected]
www.terlet.com