HackRF​ ​One

Disclaimer:

This document contains information based on research that has been gathered by employee(s) of The Senator
Patrick Leahy Center for Digital Investigation (LCDI). The data contained in this project is submitted
voluntarily and is unaudited. Every effort has been made by LCDI to assure the accuracy and reliability of the
data contained in this report. However, LCDI nor any of our employees make no representation, warranty or
guarantee in connection with this report and hereby expressly disclaims any liability or responsibility for loss
or damage resulting from use of this data. Information in this report can be downloaded and redistributed by
any person or persons. Any redistribution must maintain the LCDI logo and any references from this report
must​ ​be​ ​properly​ ​annotated.

12/01/2017 175​ ​Lakeside​ ​Ave,​ ​Room​ ​300A

http://computerforensicsblog.champlain.edu/ Phone:​ ​(802)​ ​865-5744
Fax:​ ​(802)​ ​865-6446 12/01/2017

HackRF​ ​One
Page​ ​1​ ​of​ ​34
 Contents
Introduction 3

Background 3

Purpose​ ​and​ ​Scope 3

Research​ ​Questions 3

Terminology 3

Getting​ ​Started 5

Radio​ ​Basics 5

Hardware​ ​Introduction 6

Software​ ​Introduction 9

HackRF​ ​One​ ​Basics 9

Setting​ ​up​ ​the​ ​HackRF​ ​One​ ​Device 9

Setting​ ​up​ ​the​ ​work​ ​environment 9

Installing​ ​GNU​ ​Radio​ ​Companion 10

Receiving​ ​FM​ ​Radio​ ​Signals 12

Customization​ ​of​ ​Receiving​ ​FM​ ​Radio​ ​Signals 16

Transmitting​ ​FM​ ​Radio​ ​Signals 18

Retransmitting​ ​FM​ ​Radio​ ​Signals 20

Live​ ​Broadcasting​ ​FM​ ​Radio​ ​Signals 21

Further​ ​Work 22

Appendix 23

Commonly​ ​Used​ ​Functions​ ​on​ ​GNU​ ​Radio​ ​Companion 23

FCC​ ​ID 26

References 33

HackRF​ ​One
Page​ ​2​ ​of​ ​34
 Introduction
This​ ​document​ ​will​ ​serve​ ​as​ ​a​ ​tutorial​ ​for​ ​the​ ​use​ ​of​ ​the​ ​HackRF​ ​One​ ​(HRF1)​ ​device,​ ​which​ ​is​ ​used​ ​to​ ​receive
and​ ​transmit​ ​signals​ ​between​ ​the​ ​frequencies​ ​of​ ​1​ ​MHz​ ​and​ ​6​ ​GHz​ ​(Ossmann,​ ​“HackRF​ ​One,"​ ​n.d.).​ ​The​ ​basic
functions​ ​of​ ​the​ ​HackRF​ ​One​ ​device​ ​and​ ​the​ ​GNU​ ​Radio​ ​Companion​ ​software​ ​will​ ​be​ ​explained​ ​throughout​ ​this
tutorial.

Background
The​ ​HackRF​ ​One​ ​is​ ​a​ ​Software​ ​Defined​ ​Radio​ ​(SDR)​ ​device​ ​with​ ​the​ ​ability​ ​to​ ​digitize​ ​radio​ ​signals​ ​that​ ​are
received​ ​or​ ​transmitted​ ​by​ ​the​ ​device.​ ​The​ ​HRF1​ ​works​ ​with​ ​frequencies​ ​from​ ​1MHz​ ​to​ ​6​ ​GHz,​ ​which​ ​includes
most​ ​devices​ ​operating​ ​with​ ​Bluetooth,​ ​FM​ ​radio,​ ​near-field​ ​communication​ ​(NFC),​ ​and​ ​cellular​ ​technology.
The​ ​device​ ​is​ ​operated​ ​in​ ​conjunction​ ​with​ ​a​ ​computer​ ​and​ ​software​ ​that​ ​can​ ​process​ ​SDR,​ ​such​ ​as​ ​GNU​ ​Radio
Companion​ ​(GRC)​ ​(“HackRF​ ​One,"​ ​n.d.).
The​ ​HRF1​ ​device​ ​operates​ ​in​ ​half​ ​duplex​ ​mode,​ ​meaning​ ​that​ ​it​ ​is​ ​only​ ​able​ ​to​ ​either​ ​receive​ ​transmissions​ ​or
transmit​ ​signals​ ​one​ ​at​ ​a​ ​time,​ ​rather​ ​than​ ​receiving​ ​and​ ​transmitting​ ​at​ ​the​ ​same​ ​time​ ​(Ossmann,​ ​“HackRF
One,"​ ​n.d.).

Purpose​ ​and​ ​Scope

The​ ​purpose​ ​of​ ​this​ ​tutorial​ ​is​ ​to​ ​provide​ ​a​ ​basic​ ​understanding​ ​of​ ​the​ ​HackRF​ ​One​ ​device​ ​and​ ​the​ ​GNU​ ​Radio
Companion​ ​software​ ​through​ ​written​ ​instructions,​ ​pictures,​ ​and​ ​video​ ​tutorials​ ​in​ ​order​ ​to​ ​demonstrate​ ​the
process​ ​of​ ​receiving,​ ​broadcasting,​ ​retransmitting,​ ​and​ ​live​ ​transmitting​ ​signals.

Research​ ​Questions
1. What​ ​is​ ​the​ ​HackRF​ ​One?
2. How​ ​can​ ​the​ ​HackRF​ ​One​ ​be​ ​used?

Terminology
Amplitude​ ​-​ ​The​ ​strength​ ​of​ ​the​ ​radio​ ​signal​ ​("Amplitude​ ​Modulation,"​ ​2017).
Digital​ ​Signal​ ​Processing​ ​(DSP)​ ​-​ ​Signals​ ​processed​ ​via​ ​analysis,​ ​modification,​ ​and​ ​synthesis​ ​by​ ​a​ ​sequence​ ​of
numbers​ ​that​ ​represent​ ​samples​ ​of​ ​a​ ​continuous​ ​variable​ ​in​ ​a​ ​domain​ ​such​ ​as​ ​time,​ ​space,​ ​or​ ​frequency​ ​(Rouse,
“DSP,"​ ​n.d.).

GNU​ ​Radio​ ​Companion​​ ​-​ ​A​ ​graphic​ ​user​ ​interface​ ​(GUI)​ ​software​ ​that​ ​allows​ ​users​ ​to​ ​create​ ​a​ ​flowgraph​ ​that
visualizes​ ​and​ ​processes​ ​signals​ ​(“GNU​ ​Radio​ ​Companion,"​ ​n.d.).

HackRF​ ​One
Page​ ​3​ ​of​ ​34
Filter​ ​-​ ​Helps​ ​clean​ ​up​ ​received​ ​signals​ ​in​ ​order​ ​to​ ​limit​ ​unnecessary​ ​noise​ ​and​ ​interference,​ ​and​ ​to​ ​clean​ ​up
signals​ ​when​ ​transmitting​ ​to​ ​cause​ ​less​ ​radio​ ​interference​ ​("Low-pass​ ​Filter,"​ ​2017)​.
Hertz​ ​(Hz)​ ​-​ ​Derived​ ​unit​ ​of​ ​frequency.​ ​Defined​ ​as​ ​one​ ​cycle​ ​per​ ​second.
Radio​ ​Frequency​ ​-​ ​Number​ ​of​ ​cycles​ ​per​ ​second​ ​of​ ​radio​ ​waves;​ ​measured​ ​in​ ​hertz​ ​(Hz)​ ​("Radio​ ​Frequency,"
n.d.).
Receive​​ ​-​ ​The​ ​act​ ​of​ ​obtaining​ ​and​ ​interpreting​ ​radio​ ​waves​ ​from​ ​other​ ​devices​ ​("Radio​ ​Receiver,"​ ​2017).
Functions​ ​in​ ​the​ ​form​ ​of​ ​software​ ​controlled​ ​modules​ ​while​ ​using​ ​SDR​ ​(Rouse,​ ​“SDR,"​ ​n.d.).
Sample​ ​Rate​ ​-​ ​Rate​ ​at​ ​which​ ​data​ ​is​ ​taken​ ​digitally​ ​over​ ​a​ ​period​ ​of​ ​time.​ ​Measured​ ​in​ ​Hz.​ ​(Christensson,
2015).
Software​ ​Defined​ ​Radio​ ​(SDR)​​ ​-​ ​Used​ ​to​ ​transmit​ ​radio​ ​waves​ ​via​ ​hardware.​ ​SDR​ ​emulates​ ​radio​ ​hardware
Transmit​ ​-​ ​The​ ​act​ ​of​ ​sending​ ​out​ ​a​ ​signal​ ​via​ ​a​ ​wire​ ​or​ ​radio​ ​waves​ ​("Transmit,"​ ​2014)​.

HackRF​ ​One
Page​ ​4​ ​of​ ​34
 Getting​ ​Started
Radio​ ​Basics
1. Radio​ ​Waves​ ​-​ ​Part​ ​of​ ​a​ ​larger​ ​group​ ​of​ ​waves​ ​called​ ​electromagnetic​ ​radiation​.​ ​Radio​ ​waves​ ​can​ ​be
found​ ​on​ ​the​ ​Electromagnetic​ ​Spectrum​ ​with​ ​X-rays,​ ​Infrared,​ ​Microwaves,​ ​etc.
2. Data​ ​on​ ​Radio​ ​Waves​​ ​-​ ​There​ ​are​ ​two​ ​major​ ​ways​ ​that​ ​audio​ ​data​ ​is​ ​encoded​ ​onto​ ​a​ ​radio​ ​wave,​ ​A.M.
and​ ​F.M.​ ​These​ ​two​ ​types​ ​usually​ ​have​ ​a​ ​consistent​ ​pattern​ ​throughout​ ​the​ ​entire​ ​wavelength.
(Northwestern​ ​University,​ ​“How​ ​is​ ​data​ ​put​ ​on​ ​radio​ ​waves?”)​ ​(Northwestern​ ​University,​ ​“What​ ​are
radio​ ​waves?,"​ ​n.d.)​.
a. A.M.​ ​–​ ​Amplitude​ ​Modulation
i. Information​ ​is​ ​put​ ​in​ ​a​ ​radio​ ​wave​ ​by​ ​changing​ ​the​ ​height​ ​of​ ​the​ ​wave.
b. F.M.​ ​–​ ​Frequency​ ​Modulation
i. Information​ ​is​ ​put​ ​in​ ​a​ ​radio​ ​wave​ ​by​ ​changing​ ​how​ ​close​ ​the​ ​waves​ ​are​ ​to​ ​each​ ​other.

HackRF​ ​One
Page​ ​5​ ​of​ ​34
Hardware​ ​Introduction
1. Computer​​ ​–​ ​Needed​ ​to​ ​run​ ​software​ ​to​ ​analyze​ ​what​ ​was​ ​captured.
2. Radio​ ​device​​ ​–​ ​Any​ ​device​ ​that​ ​is​ ​capable​ ​of​ ​receiving​ ​transmissions​ ​from​ ​the​ ​HackRF​ ​One.
3. HackRF​ ​One​​ ​–​ ​The​ ​device​ ​used​ ​to​ ​receive​ ​and​ ​transmit​ ​signals.​ ​The​ ​packaging​ ​includes:
a. The​ ​HackRF​ ​One​ ​device.
b. Micro-​ ​USB​ ​to​ ​USB​ ​cable​ ​used​ ​to​ ​connect​ ​the​ ​HackRF​ ​One​ ​device​ ​to​ ​a​ ​computer.
c. ANT500​ ​antenna.​ ​Note​ ​that​ ​using​ ​the​ ​HRF1​ ​without​ ​an​ ​antenna​ ​or​ ​a​ ​dummy​ ​plug​ ​could​ ​cause
damage​ ​to​ ​the​ ​device​ ​(Ossmann,​ ​2014).​ ​Additionally,​ ​the​ ​ANT500​ ​only​ ​supports​ ​frequencies
from​ ​75​ ​MHz​ ​to​ ​1​ ​GHz​ ​(“ANT500,"​ ​n.d.).

HackRF​ ​One
Page​ ​6​ ​of​ ​34
HackRF​ ​One
Page​ ​7​ ​of​ ​34
Button/Light Function

Reset​ ​Button Used​ ​to​ ​reboot​ ​the​ ​HackRF​ ​One,​ ​equivalent​ ​to​ ​unplugging​ ​the​ ​device
and​ ​plugging​ ​it​ ​back​ ​in​ ​(“HackRF​ ​One​ ​One,"​ ​n.d.).
3v3​ ​LED All​ ​three​ ​of​ ​these​ ​LEDs​ ​are​ ​used​ ​to​ ​indicate​ ​power​ ​and​ ​should​ ​be​ ​lit
when​ ​the​ ​HackRF​ ​One​ ​is​ ​plugged​ ​in.​ ​The​ ​various​ ​colors​ ​are​ ​used​ ​to
1V8​ ​LED distinguish​ ​between​ ​the​ ​multiple​ ​LEDs​ ​on​ ​the​ ​side​ ​of​ ​the​ ​HackRF​ ​One
(“FAQ,"​ ​n.d.).​ ​
RF​ ​LED
USB​ ​LED Indicates​ ​that​ ​the​ ​HackRF​ ​One​ ​is​ ​communicating​ ​over​ ​USB​ ​(“FAQ,"
n.d.).
DFU​ ​Button Used​ ​to​ ​install​ ​or​ ​update​ ​the​ ​firmware​ ​if​ ​it​ ​is​ ​not​ ​working​ ​properly​ ​or
has​ ​never​ ​been​ ​installed​ ​(“HackRF​ ​One,"​ ​n.d.).
RX​ ​LED An​ ​orange​ ​light​ ​that​ ​indicates​ ​that​ ​the​ ​device​ ​is​ ​receiving​ ​information
(“FAQ,"​ ​n.d.).
TX​ ​LED A​ ​red​ ​light​ ​that​ ​indicates​ ​that​ ​the​ ​device​ ​is​ ​transmitting​ ​information
(“FAQ,"​ ​n.d.).

Table​ ​1​ ​–​ ​HackRF​ ​One​ ​LED​ ​Lights

HackRF​ ​One
Page​ ​8​ ​of​ ​34
Software​ ​Introduction
The​ ​HackRF​ ​One​ ​is​ ​primarily​ ​operated​ ​using​ ​the​ ​Ubuntu​​ ​Operating​ ​System,​ ​which​ ​the​ ​GNU​ ​Radio
Companion​​ ​SDR​ ​system​ ​uses​ ​as​ ​a​ ​means​ ​to​ ​capture,​ ​analyze,​ ​and​ ​transmit​ ​radio​ ​frequencies​ ​generated​ ​from
another​ ​hardware​ ​device.

HackRF​ ​One​ ​Basics

Setting​ ​up​ ​the​ ​HackRF​ ​One​ ​Device
1. Attach​ ​the​ ​antenna​ ​to​ ​the​ ​antenna​ ​port​ ​after​ ​removing​ ​the​ ​red​ ​safety​ ​cap.​ ​Attaching​ ​the​ ​antenna​ ​first​ ​is
vital​ ​because​ ​running​ ​the​ ​HackRF​ ​One​ ​without​ ​an​ ​antenna​ ​can​ ​damage​ ​the​ ​device’s​ ​hardware.
2. Ubuntu​ ​Linux​ ​is​ ​recommended​ ​as​ ​the​ ​operating​ ​system​ ​alongside​ ​GNU​ ​Radio.​ ​Ubuntu​ ​can​ ​be
downloaded​ ​from​ ​this​ ​link:​ ​https://www.ubuntu.com/download
3. Plug​ ​the​ ​HackRF​ ​One​ ​into​ ​the​ ​computer​ ​with​ ​the​ ​Micro-USB​ ​to​ ​USB​ ​cable.​ ​Confirm​ ​that​ ​the​ ​first​ ​three
LED​ ​lights​ ​are​ ​illuminated​ ​to​ ​ensure​ ​the​ ​device​ ​is​ ​working.

Video​ ​1​ ​–​ ​Device​ ​Overview​:

Setting​ ​up​ ​the​ ​work​ ​environment

1. Before​ ​getting​ ​started,​ ​the​ ​HackRF​ ​One​ ​libraries​ ​must​ ​be​ ​installed​ ​on​ ​the​ ​computer​ ​to​ ​start​ ​using​ ​the
device.
a. The​ ​libraries​ ​can​ ​be​ ​installed​ ​with​ ​the​ ​Terminal​ ​command​ ​“sudo​ ​apt-get​ ​install​ ​hackrf”

2. After​ ​installation,​ ​type​ ​the​ ​command​ ​“hackrf_info”​ ​to​ ​verify​ ​that​ ​the​ ​HRF1​ ​device​ ​is​ ​connected.
a. After​ ​a​ ​successful​ ​installation,​ ​the​ ​terminal​ ​should​ ​respond​ ​with​ ​“Found​ ​HackRF​ ​board”​.

HackRF​ ​One
Page​ ​9​ ​of​ ​34
 b. If​ ​the​ ​terminal​ ​shows​ ​the​ ​HRF1​ ​as​ ​not​ ​connected,​ ​troubleshoot​ ​by​ ​verifying​ ​wires​ ​are​ ​plugged​ ​in
and​ ​power​ ​is​ ​being​ ​supplied​ ​to​ ​the​ ​device.

Installing​ ​GNU​ ​Radio​ ​Companion

1. In​ ​order​ ​to​ ​install​ ​the​ ​GNU​ ​Radio​ ​Companion​ ​software,​ ​open​ ​a​ ​terminal​ ​window.
2. Type​ ​in​ ​the​ ​command:​ ​“apt-get​ ​install​ ​gnuradio”​.
a. If​ ​the​ ​root​ ​user​ ​is​ ​not​ ​logged​ ​in,​ ​type​ ​“sudo”​ ​in​ ​front​ ​of​ ​this​ ​command.

3. Now,​ ​open​ ​GNU​ ​Radio​ ​Companion​ ​using​ ​the​ ​command:​ ​“gnuradio-companion”.

a. Once​ ​initialized,​ ​GNU​ ​Radio​ ​Companion​ ​displays​ ​its​ ​user​ ​interface,​ ​which​ ​automatically​ ​opens
an​ ​untitled​ ​project.​ ​This​ ​will​ ​show​ ​an​ ​empty​ ​white​ ​space​ ​at​ ​the​ ​center,​ ​which​ ​will​ ​be​ ​used​ ​to
build​ ​a​ ​flowgraph.​ ​The​ ​default​ ​options​ ​and​ ​variable​ ​blocks​ ​will​ ​already​ ​be​ ​in​ ​the​ ​flowgraph​ ​(See
Figure​ ​9​ ​below).​ ​The​ ​sidebar​ ​to​ ​the​ ​right​ ​holds​ ​other​ ​blocks​ ​to​ ​add​ ​to​ ​the​ ​flowgraph.

HackRF​ ​One
Page​ ​10​ ​of​ ​34
 b. The​ ​play​ ​button​ ​on​ ​the​ ​top​ ​toolbar​ ​is​ ​used​ ​to​ ​execute​ ​the​ ​flowgraph.​ ​The​ ​red​ ​‘X’​ ​next​ ​to​ ​it​ ​can​ ​be
used​ ​to​ ​kill​ ​the​ ​program,​ ​but​ ​it​ ​is​ ​recommended​ ​to​ ​use​ ​the​ ​red​ ​‘X’​ ​in​ ​the​ ​popup​ ​window​ ​when​ ​the
program​ ​is​ ​running.​ ​Using​ ​the​ ​kill​ ​button​ ​in​ ​the​ ​top​ ​toolbar​ ​will​ ​cause​ ​issues​ ​with​ ​file​ ​sinks.
c. The​ ​flowgraph​ ​itself​ ​is​ ​divided​ ​into​ ​4​ ​components:
i. Options​ ​(available​ ​by​ ​default​ ​upon​ ​launching​ ​GRC)​ ​-​ ​generate​ ​options​ ​should​ ​be​ ​set​ ​to
QT​ ​GUI.​ ​Given​ ​the​ ​capabilities​ ​of​ ​the​ ​current​ ​technology,​ ​it​ ​has​ ​been​ ​recommended​ ​that
QT​ ​functions​ ​are​ ​used​ ​instead​ ​of​ ​WX​ ​on​ ​all​ ​functions​,​ ​as​ ​WX​ ​may​ ​not​ ​be​ ​supported​ ​in
the​ ​near​ ​future.​ ​WX​ ​and​ ​QT​ ​are​ ​Python​ ​Frameworks.
ii. Variable​ ​(available​ ​by​ ​default​ ​upon​ ​launching​ ​GRC)​ ​-​ ​used​ ​to​ ​set​ ​the​ ​sample​ ​rate​ ​for​ ​the
HRF1.​ ​Double​ ​click​ ​this​ ​block​ ​to​ ​set​ ​the​ ​sample​ ​rate​ ​value.
1. It​ ​is​ ​recommended​ ​to​ ​use​ ​this​ ​block​ ​to​ ​change​ ​the​ ​sample​ ​rate,​ ​as​ ​it​ ​will​ ​change​ ​all
of​ ​the​ ​sample​ ​rates​ ​to​ ​match​ ​when​ ​the​ ​flowgraph​ ​is​ ​more​ ​complex,​ ​instead​ ​of
changing​ ​it​ ​individually​ ​in​ ​each​ ​block.
iii. Functions​ ​-​ ​the​ ​wide​ ​array​ ​of​ ​data​ ​blocks,​ ​which​ ​are​ ​listed​ ​in​ ​the​ ​menu​ ​to​ ​the​ ​right​ ​of​ ​the
screen,​ ​are​ ​used​ ​to​ ​build​ ​the​ ​flowgraph.​ ​The​ ​function​ ​blocks​ ​encompass​ ​the​ ​most
essential​ ​parts​ ​of​ ​the​ ​software​ ​because​ ​they​ ​provide​ ​different​ ​commands​ ​to​ ​accomplish

HackRF​ ​One
Page​ ​11​ ​of​ ​34
 specific​ ​tasks.​ ​Selecting​ ​and​ ​dragging​ ​a​ ​function​ ​block​ ​to​ ​the​ ​flowgraph​ ​provides​ ​the
ability​ ​to​ ​initialize​ ​a​ ​set​ ​of​ ​commands,​ ​and​ ​double​ ​clicking​ ​on​ ​a​ ​block​ ​inside​ ​the
flowgraph​ ​opens​ ​its​ ​properties.
iv. Arrows​ ​-​ ​connect​ ​function​ ​blocks​ ​in​ ​order​ ​to​ ​create​ ​the​ ​flowgraph.

Receiving​ ​FM​ ​Radio​ ​Signals

This​ ​section​ ​outlines​ ​how​ ​to​ ​receive​ ​FM​ ​radio​ ​signals​ ​from​ ​the​ ​HackRF​ ​One​ ​using​ ​GNU​ ​Radio​ ​Companion​ ​in
order​ ​to​ ​visualize​ ​the​ ​signal​ ​in​ ​a​ ​flowgraph.​ ​This​ ​section​ ​also​ ​contains​ ​a​ ​video​ ​tutorial.

1. Upon​ ​starting​ ​the​ ​GNU​ ​Radio​ ​Companion​ ​software,​ ​there​ ​will​ ​be​ ​two​ ​boxes​ ​already​ ​present​ ​on​ ​the
flowgraph​ ​area:​ ​Variable​ ​and​ ​Options​.​ ​These​ ​default​ ​to​ ​a​ ​set​ ​value,​ ​which​ ​can​ ​be​ ​altered,​ ​as​ ​mentioned
above.​ ​In​ ​the​ ​Options​ ​block,​ ​the​ ​Generate​ ​Options​ ​should​ ​be​ ​set​ ​to​ ​QT​ ​GUI​.
2. In​ ​the​ ​Variable​ ​block,​ ​change​ ​the​ ​sample​ ​rate​ ​(samp_rate)​ ​to​ ​the​ ​correct​ ​value.​ ​The​ ​lowest​ ​recommended
sample​ ​rate​ ​is​ ​2e6​ ​(2​ ​million)​ ​Hz,​ ​and​ ​the​ ​highest​ ​sample​ ​rate​ ​used​ ​should​ ​be​ ​20e6​ ​(20​ ​million)​ ​Hz.​ ​It​ ​is
recommended​ ​to​ ​begin​ ​at​ ​4e6​ ​Hz,​ ​and​ ​decrease​ ​as​ ​needed.​ ​A​ ​computer​ ​with​ ​less​ ​processing​ ​speed
should​ ​not​ ​have​ ​a​ ​high​ ​sample​ ​rate​ ​frequency.
3. To​ ​begin​ ​creating​ ​the​ ​flowgraph​ ​to​ ​receive​ ​FM​ ​radio​ ​signals,​ ​add​ ​an​ ​osmocom​ ​source​ ​function​ ​via​ ​(no
module​ ​specified)​ ​>​ ​Source​ ​>​ ​osmocom​ ​Source​ ​(or​ ​search​ ​for​ ​osmocom​ ​source​ ​via​ ​the​ ​magnifying
glass,​ ​which​ ​is​ ​found​ ​on​ ​the​ ​right​ ​side​ ​of​ ​the​ ​top​ ​menu).​ ​This​ ​enables​ ​the​ ​ability​ ​to​ ​receive​ ​data​ ​captured
by​ ​the​ ​HackRF​ ​One​ ​device.
a. The​ ​sample​ ​rate​ ​should​ ​already​ ​be​ ​set​ ​to​ ​samp_rate​,​ ​which​ ​was​ ​assigned​ ​in​ ​the​ ​Variable​ ​box.
Changing​ ​the​ ​samp_rate​ ​in​ ​the​ ​Variable​ ​box​ ​will​ ​reflect​ ​throughout​ ​the​ ​rest​ ​of​ ​the​ ​flowgraph.
b. Change​ ​the​ ​Ch0​ ​Frequency​ ​(Hz)​ ​to​ ​the​ ​radio​ ​station​ ​that​ ​is​ ​strongest​ ​in​ ​your​ ​area.​ ​For​ ​example,
this​ ​should​ ​be​ ​formatted​ ​as​ ​“98.9e6”.​ ​Setting​ ​the​ ​osmocom​ ​source​ ​>​ ​Ch0​ ​frequency​ ​tells​ ​the
HackRF​ ​One​ ​device​ ​which​ ​radio​ ​channel​ ​to​ ​tune​ ​to.
c. It​ ​is​ ​recommended​ ​to​ ​turn​ ​off​ ​the​ ​RF​ ​amplifier​ ​by​ ​setting​ ​the​ ​Ch0:​ ​RF​ ​Gain​ ​(dB)​ ​value​ ​to​ ​0.​ ​The
RF​ ​Gain​ ​amplifies​ ​the​ ​frequency​ ​source​ ​at​ ​its​ ​default​ ​setting​ ​of​ ​10​ ​dB,​ ​but​ ​it​ ​is​ ​not​ ​necessary​ ​or
recommended​ ​to​ ​have​ ​this​ ​setting​ ​turned​ ​on.
4. Now,​ ​add​ ​the​ ​DC​ ​Blocker​,​ ​which​ ​filters​ ​out​ ​the​ ​direct​ ​current​ ​from​ ​the​ ​power​ ​supply​ ​to​ ​the​ ​HRF1,​ ​which
can​ ​interfere​ ​with​ ​the​ ​device.​ ​If​ ​there​ ​is​ ​no​ ​DC​ ​Blocker​ ​present​ ​in​ ​the​ ​flowgraph,​ ​there​ ​will​ ​be​ ​a​ ​peak​ ​in
the​ ​center​ ​of​ ​the​ ​flowgraph​ ​when​ ​being​ ​executed,​ ​which​ ​can​ ​be​ ​misinterpreted​ ​as​ ​a​ ​signal.

HackRF​ ​One
Page​ ​12​ ​of​ ​34
 a. Set​ ​the​ ​length​ ​value​ ​to​ ​1024.
b. Connect​ ​the​ ​osmocom​ ​Source​ ​block​ ​to​ ​the​ ​DC​ ​Blocker​ ​with​ ​an​ ​arrow.
5. In​ ​order​ ​to​ ​visualize​ ​the​ ​signals​ ​being​ ​received​ ​by​ ​the​ ​HackRF​ ​One​ ​device,​ ​the​ ​frequency​ ​sink​ ​function
needs​ ​to​ ​be​ ​added​ ​to​ ​the​ ​flowgraph.​ ​This​ ​function​ ​can​ ​be​ ​found​ ​via​ ​Instrumentation​ ​>​ ​QT​ ​>​ ​QT​ ​GUI
Sink​ ​(or​ ​by​ ​searching​ ​for​ ​QT​ ​GUI​ ​Sink​).
a. Set​ ​the​ ​Center​ ​Frequency​ ​(Hz)​ ​to​ ​the​ ​frequency​ ​from​ ​Ch0​ ​Frequency​ ​(Hz)​ ​in​ ​the​ ​osmocom
Source​ ​function.​ ​For​ ​example,​ ​98.9e6.
b. In​ ​order​ ​to​ ​visualize​ ​the​ ​whole​ ​range​ ​of​ ​FM​ ​radio​ ​signals,​ ​change​ ​the​​ ​bandwidth​ ​(Hz)​ ​to​ ​20e6.
This​ ​is​ ​normally​ ​set​ ​to​ ​your​ ​sample​ ​rate​ ​by​ ​default,​ ​but​ ​changing​ ​the​ ​value​ ​will​ ​not​ ​affect​ ​your
samp_rate​ ​in​ ​the​ ​Variable​ ​function.​ ​Also,​ ​the​ ​focus​ ​of​ ​the​ ​flowgraph​ ​will​ ​still​ ​be​ ​on​ ​the
frequency​ ​set​ ​as​ ​the​ ​Ch0​ ​Frequency​ ​while​ ​also​ ​showing​ ​the​ ​full​ ​range​ ​of​ ​radio​ ​channels​ ​in​ ​the
area.
c. The​ ​Update​ ​Rate​ ​can​ ​be​ ​changed​ ​from​ ​10​ ​to​ ​5.​ ​This​ ​indicates​ ​the​ ​amount​ ​of​ ​times​ ​per​ ​second​ ​the
graph​ ​updates.​ ​5​ ​will​ ​cause​ ​less​ ​strain​ ​on​ ​your​ ​system​ ​if​ ​you​ ​do​ ​not​ ​have​ ​a​ ​high​ ​end​ ​computer.
d. Change​ ​Show​ ​RF​ ​Frequency​ ​to​ ​“yes”.​ ​This​ ​will​ ​display​ ​the​ ​frequencies​ ​on​ ​the​ ​x-axis​ ​of​ ​the
frequency​ ​sink​ ​correctly.
e. Lastly,​ ​connect​ ​the​ ​QT​ ​GUI​ ​Sink​ ​(in)​ ​function​ ​to​ ​the​ ​osmocom​ ​Source​ ​(out)​ ​function​ ​with​ ​an
arrow.​ ​The​ ​flowgraph​ ​should​ ​look​ ​like​ ​this:

HackRF​ ​One
Page​ ​13​ ​of​ ​34
 6. Press​ ​the​ ​green​ ​play​ ​button​ ​at​ ​the​ ​top​ ​in​ ​order​ ​to​ ​run​ ​the​ ​flowgraph.​ ​Upon​ ​pressing​ ​it,​ ​a​ ​prompt​ ​to​ ​save
the​ ​flowgraph​ ​will​ ​appear​ ​in​ ​a​ ​new​ ​window.​ ​The​ ​file​ ​will​ ​autosave​ ​every​ ​time​ ​afterwards.​ ​After​ ​the​ ​file
saves,​ ​the​ ​python​ ​script​ ​will​ ​be​ ​generated​ ​in​ ​the​ ​bottom​ ​left​ ​of​ ​the​ ​screen​ ​and​ ​the​ ​visualization​ ​will​ ​show
on​ ​the​ ​main​ ​area​ ​of​ ​the​ ​screen.

a. The​ ​first​ ​tab​ ​in​ ​the​ ​Top​ ​Block​ ​window​ ​will​ ​show​ ​the​ ​Frequency​ ​Display.​ ​There​ ​should​ ​be
obvious​ ​differences​ ​between​ ​the​ ​strong​ ​signals​ ​and​ ​the​ ​rest​ ​of​ ​the​ ​frequencies.​ ​For​ ​example,
channels​ ​98.9,​ ​91.3,​ ​and​ ​102.9​ ​are​ ​the​ ​strongest​ ​in​ ​the​ ​Burlington,​ ​VT​ ​area.
7. To​ ​stop​ ​the​ ​flowgraph,​ ​click​ ​the​ ​red​ ​X​ ​in​ ​the​ ​top​ ​left​ ​of​ ​the​ ​pop​ ​up​ ​window.​ ​Sometimes,​ ​the​ ​HackRF
One​ ​may​ ​need​ ​to​ ​be​ ​reset​ ​(via​ ​the​ ​reset​ ​button​ ​on​ ​the​ ​device)​ ​because​ ​it​ ​will​ ​continue​ ​receiving​ ​signals
even​ ​after​ ​the​ ​flowgraph​ ​is​ ​closed.
8. To​ ​listen​ ​to​ ​the​ ​signals,​ ​a​ ​few​ ​things​ ​need​ ​to​ ​be​ ​done​ ​in​ ​addition​ ​to​ ​the​ ​flowgraph​ ​that​ ​has​ ​already​ ​been
built.​ ​The​ ​Low​ ​Pass​ ​Filter​ ​function​ ​(found​ ​via​ ​searching​ ​for​ ​Low​ ​Pass​ ​Filter​)​ ​will​ ​focus​ ​on​ ​the​ ​center
frequency​ ​and​ ​reduce​ ​noise​ ​from​ ​the​ ​surrounding​ ​stations.
a. The​ ​Decimation​ ​value​​ ​should​ ​be​ ​set​ ​to​ ​20,​ ​which​ ​will​ ​divide​ ​the​ ​sample​ ​rate​ ​by​ ​20.​ ​This​ ​will​ ​get
the​ ​sample​ ​rate​ ​to​ ​the​ ​same​ ​rate​ ​as​ ​the​ ​audio.

HackRF​ ​One
Page​ ​14​ ​of​ ​34
 b. The​ ​Cutoff​ ​Frequency​ ​should​ ​be​ ​75e3.​ ​This​ ​is​ ​how​ ​wide​ ​the​ ​signal​ ​is.
c. The​ ​Transition​ ​Width​ ​should​ ​be​ ​25e3.​ ​This​ ​is​ ​how​ ​sharply​ ​the​ ​unneeded​ ​signals​ ​are​ ​filtered​ ​out,
and​ ​applies​ ​a​ ​more​ ​focused​ ​center​ ​frequency.​ ​The​ ​lower​ ​the​ ​transition​ ​width,​ ​the​ ​sharper​ ​the
transition​ ​width.​ ​25e3​ ​is​ ​a​ ​good​ ​width​ ​value​ ​for​ ​FM​ ​radio.
d. Connect​ ​the​ ​Low​ ​Pass​ ​Filter​ ​function​ ​to​ ​the​ ​osmocom​ ​Source​ ​function.
9. A​ ​Rational​ ​Resampler​ ​should​ ​now​ ​be​ ​added​ ​as​ ​a​ ​way​ ​to​ ​modify​ ​the​ ​sample​ ​rate​ ​by​ ​a​ ​ratio,​ ​as​ ​GNU​ ​radio
companion​ ​will​ ​only​ ​allow​ ​the​ ​sample​ ​rate​ ​to​ ​be​ ​changed​ ​by​ ​integers.​ ​By​ ​setting​ ​this​ ​rate​ ​as​ ​12​ ​to​ ​5,​ ​this
will​ ​help​ ​move​ ​the​ ​sample​ ​rate​ ​closer​ ​to​ ​the​ ​targeted​ ​audio​ ​frequency.​ ​If​ ​the​ ​sample​ ​rate​ ​is​ ​faster​ ​than​ ​the
actual​ ​audio​ ​rate,​ ​then​ ​it​ ​will​ ​affect​ ​the​ ​speed​ ​of​ ​the​ ​audio​ ​and​ ​distort​ ​the​ ​sound,​ ​so​ ​this​ ​can​ ​fix​ ​that
problem.
a. Connect​ ​this​ ​function​ ​to​ ​the​ ​Low​ ​Pass​ ​Filter​ ​block.
10. In​ ​addition,​ ​the​ ​Wide​ ​Band​ ​Frequency​ ​function​ ​is​ ​needed.​ ​This​ ​is​ ​found​ ​by​ ​searching​ ​for​ ​WBFM
Receive​.​ ​This​ ​block​ ​will​ ​have​ ​one​ ​blue​ ​input​ ​(like​ ​the​ ​rest​ ​of​ ​the​ ​inputs/outputs​ ​on​ ​the​ ​flowgraph)​ ​and
one​ ​orange​ ​output.​ ​Blue​ ​outputs​ ​are​ ​complex​ ​numbers​ ​so​ ​there​ ​is​ ​a​ ​real​ ​and​ ​imaginary​ ​number​ ​being
received.​ ​The​ ​WBFM​ ​Receive​ ​function​ ​is​ ​combining​ ​both​ ​complex​ ​numbers​ ​and​ ​creating​ ​one​ ​output​ ​via
the​ ​orange​ ​real​ ​number​ ​output.
a. Set​ ​the​ ​Quadrature​ ​Rate​ ​to​ ​480e3,​ ​which​ ​is​ ​recommended​ ​for​ ​the​ ​FM​ ​radio​ ​audio​ ​receive​ ​task.
b. Set​ ​the​ ​Audio​ ​Decimation​ ​to​ ​10,​ ​which​ ​will​ ​reduce​ ​the​ ​audio​ ​rate​ ​to​ ​48​ ​KHz​ ​since​ ​you’re
dividing​ ​it​ ​by​ ​10.​ ​This​ ​is​ ​the​ ​rate​ ​at​ ​which​ ​the​ ​audio​ ​will​ ​be​ ​heard.
c. Connect​ ​this​ ​function​ ​to​ ​the​ ​Rational​ ​Resampler.
11. The​ ​last​ ​function​ ​needed​ ​is​ ​the​ ​Audio​ ​Sink​ ​(found​ ​via​ ​searching​ ​for​ ​Audio​ ​Sink​).​ ​This​ ​will​ ​allow​ ​you​ ​to
actually​ ​hear​ ​the​ ​audio​ ​from​ ​the​ ​radio​ ​station​ ​set​ ​as​ ​the​ ​center​ ​frequency.​ ​This​ ​block​ ​has​ ​an​ ​orange​ ​input,
which​ ​will​ ​be​ ​connected​ ​to​ ​the​ ​orange​ ​WBFM​ ​Receive​ ​output.
a. Change​ ​the​ ​sample​ ​rate​ ​to​ ​48​ ​KHz​ ​from​ ​the​ ​drop​ ​down​ ​menu.
12. Now,​ ​execute​ ​the​ ​flowgraph​ ​again​ ​by​ ​clicking​ ​the​ ​green​ ​play​ ​button​ ​in​ ​the​ ​menu.​ ​The​ ​audio​ ​should
immediately​ ​begin​ ​playing​ ​and​ ​the​ ​radio​ ​signals​ ​for​ ​the​ ​center​ ​frequency​ ​should​ ​be​ ​visualized​ ​in​ ​the
flowgraph.​ ​The​ ​audio​ ​should​ ​be​ ​clear,​ ​like​ ​listening​ ​to​ ​a​ ​normal​ ​radio,​ ​but​ ​it​ ​is​ ​dependent​ ​on​ ​the
processing​ ​speed​ ​of​ ​the​ ​computer.

Video​ ​2​ ​–​ ​Receiving​ ​Signals​ ​from​ ​the​ ​Device

HackRF​ ​One
Page​ ​15​ ​of​ ​34
Customization​ ​of​ ​Receiving​ ​FM​ ​Radio​ ​Signals
This​ ​section​ ​outlines​ ​some​ ​of​ ​the​ ​additional​ ​functionality​ ​that​ ​GRC​ ​presents,​ ​like​ ​changing​ ​the​ ​FM​ ​radio​ ​station
in​ ​real​ ​time​ ​and​ ​changing​ ​volume​ ​from​ ​the​ ​flowgraph​ ​view.​ ​This​ ​section​ ​also​ ​contains​ ​a​ ​video​ ​tutorial.

1. From​ ​the​ ​GRC​ ​flowgraph​ ​already​ ​created​ ​from​ ​the​ ​first​ ​part​ ​of​ ​this​ ​tutorial,​ ​further​ ​customizable​ ​options
are​ ​available​ ​in​ ​order​ ​to​ ​listen​ ​to​ ​a​ ​wider​ ​range​ ​of​ ​frequencies​ ​and​ ​change​ ​the​ ​volume.
2. First,​ ​copy​ ​the​ ​Variable​ ​function​ ​block​ ​and​ ​paste​ ​it​ ​twice​ ​so​ ​there​ ​are​ ​three​ ​Variable​ ​blocks​ ​present​ ​in
the​ ​flowgraph.​ ​These​ ​will​ ​aid​ ​in​ ​changing​ ​the​ ​radio​ ​station​ ​being​ ​listened​ ​to,​ ​and​ ​with​ ​updating​ ​the
sample​ ​rate.​ ​The​ ​ID​ ​tags​ ​in​ ​each​ ​of​ ​the​ ​three​ ​blocks​ ​will,​ ​by​ ​default,​ ​be​ ​named​ ​samp_rate,​ ​samp_rate0,
and​ ​samp_rate1​.
a. In​ ​the​ ​second​ ​Variable​ ​block,​ ​change​ ​the​ ​ID​ ​of​ ​samp_rate0​ ​to​ ​channel_width​,​ ​with​ ​the​ ​value​ ​of
200e3.
b. These​ ​are​ ​variables​ ​and​ ​can​ ​be​ ​set​ ​in​ ​any​ ​blocks​ ​to​ ​universally​ ​change​ ​the​ ​variables​ ​in​ ​the​ ​rest​ ​of
the​ ​flowgraph.​ ​After​ ​setting​ ​the​ ​channel​ ​width​ ​to​ ​200e3,​ ​change​ ​the​ ​decimation​ ​in​ ​the​ ​Low​ ​Pass
Filter​ ​function​ ​to​ ​int(samp_rate/channel_width)​.​ ​Since​ ​radio​ ​waves​ ​are​ ​transmitted​ ​at​ ​480​ ​KHz,
this​ ​should​ ​be​ ​the​ ​final​ ​value​ ​of​ ​the​ ​flowgraph.​ ​By​ ​dividing​ ​the​ ​sample​ ​rate​ ​by​ ​the​ ​channel​ ​width
in​ ​the​ ​Low​ ​Pass​ ​filter,​ ​you​ ​will​ ​not​ ​have​ ​to​ ​change​ ​the​ ​decimation​ ​values​ ​if​ ​you​ ​change​ ​the
sample​ ​rate.
c. In​ ​the​ ​third​ ​Variable​ ​block,​ ​change​ ​the​ ​ID​ ​of​ ​samp_rate1​ ​to​ ​center_freq​,​ ​with​ ​the​ ​value​ ​of​ ​the
target​ ​radio​ ​station.​ ​For​ ​example,​ ​98.9e6​ ​in​ ​the​ ​Burlington,​ ​VT​ ​area.
3. In​ ​order​ ​to​ ​be​ ​able​ ​to​ ​change​ ​radio​ ​stations​ ​within​ ​the​ ​flowgraph​ ​without​ ​reentering​ ​values​ ​throughout
the​ ​flowgraph,​ ​add​ ​a​ ​QT​ ​GUI​ ​Range​.​ ​This​ ​block​ ​has​ ​no​ ​input​ ​or​ ​output​ ​values.
a. Change​ ​the​ ​ID​ ​of​ ​the​ ​block​ ​to​ ​channel_freq​.
b. Change​ ​the​ ​Default​ ​Value​ ​to​ ​the​ ​targeted​ ​radio​ ​station.​ ​For​ ​example,​ ​98.9e6.
c. Change​ ​the​ ​Start​ ​value​ ​to​ ​87.9e5​ ​and​ ​the​ ​Stop​ ​value​ ​to​ ​107.9e6.​ ​These​ ​values​ ​represent​ ​the​ ​entire
range​ ​at​ ​which​ ​FM​ ​radio​ ​signals​ ​broadcast.
d. Change​ ​the​ ​Step​ ​to​ ​200e3.​ ​This​ ​represents​ ​the​ ​distance​ ​between​ ​each​ ​tick​ ​on​ ​the​ ​slider​ ​being
added.​ ​Because​ ​FM​ ​radio​ ​stations​ ​are​ ​200​ ​MHz​ ​wide,​ ​set​ ​this​ ​to​ ​200e3​ ​so​ ​each​ ​tick​ ​on​ ​the​ ​slider
represents​ ​a​ ​different​ ​radio​ ​station.

HackRF​ ​One
Page​ ​16​ ​of​ ​34
 4. In​ ​order​ ​to​ ​control​ ​volume​ ​within​ ​the​ ​flowgraph​ ​via​ ​a​ ​slider,​ ​add​ ​a​ ​second​ ​QT​ ​GUI​ ​Range​ ​to​ ​the
flowgraph.​ ​This​ ​block​ ​has​ ​no​ ​input​ ​or​ ​output​ ​values.
a. Change​ ​the​ ​ID​ ​of​ ​the​ ​block​ ​to​ ​audio_gain​.
b. Change​ ​the​ ​Default​ ​Value​ ​to​ ​1.
c. Change​ ​the​ ​Start​ ​value​ ​to​ ​0​ ​and​ ​the​ ​Stop​ ​value​ ​to​ ​10.​ ​These​ ​values​ ​represent​ ​the​ ​highest​ ​and
lowest​ ​audio​ ​volume.
d. Change​ ​the​ ​Step​ ​to​ ​0.1.
5. Now​ ​that​ ​all​ ​of​ ​the​ ​values​ ​needed​ ​are​ ​within​ ​the​ ​Variable​ ​and​ ​QT​ ​GUI​ ​Range​ ​blocks,​ ​they​ ​need​ ​to​ ​be
implemented​ ​into​ ​the​ ​flowgraph.​ ​In​ ​order​ ​to​ ​change​ ​the​ ​channel​ ​frequency,​ ​start​ ​by​ ​adding​ ​a​ ​Signal
Source​ ​block.​ ​On​ ​its​ ​own,​ ​this​ ​would​ ​just​ ​generate​ ​the​ ​one​ ​targeted​ ​frequency,​ ​with​ ​a​ ​spike​ ​at​ ​the​ ​default
1000​ ​Hz​ ​frequency.​ ​The​ ​Signal​ ​Source​ ​function​ ​can​ ​aid​ ​in​ ​changing​ ​the​ ​radio​ ​station​ ​by​ ​creating​ ​the
variables​ ​in​ ​this​ ​block​ ​and​ ​multiplying​ ​those​ ​signals​ ​by​ ​the​ ​values​ ​in​ ​the​ ​osmocom​ ​Source​.
a. Change​ ​the​ ​Frequency​ ​to​ ​“​center_freq​ ​-​ ​channel_freq”​ ​to​ ​subtract​ ​the​ ​channel​ ​frequency​ ​from
the​ ​center​ ​frequency.
b. Do​ ​not​ ​connect​ ​this​ ​block​ ​to​ ​any​ ​other​ ​function​ ​yet.
6. Now,​ ​add​ ​a​ ​Multiply​ ​function.​ ​This​ ​block​ ​has​ ​two​ ​input​ ​sources​ ​and​ ​one​ ​output​ ​source.
a. Delete​ ​the​ ​arrow​ ​between​ ​osmocom​ ​Source​ ​and​ ​the​ ​Low​ ​Pass​ ​Filter​ ​blocks.​ ​Do​ ​this​ ​by​ ​clicking
on​ ​the​ ​connecting​ ​arrow​ ​and​ ​dragging​ ​away.
b. Position​ ​the​ ​Multiply​ ​function​ ​and​ ​connect​ ​its​ ​output​ ​to​ ​the​ ​Low​ ​Pass​ ​Filter​ ​input.​ ​Connect​ ​the
Signal​ ​Source​ ​output​ ​to​ ​one​ ​of​ ​the​ ​Multiply​ ​inputs.​ ​Connect​ ​the​​ ​osmocom​ ​Source​ ​output​ ​to​ ​the
Multiply​ ​function​ ​input.
i. Notice​ ​that​ ​the​ ​Signal​ ​Source​ ​block​ ​has​ ​a​ ​grey​ ​input​ ​area.​ ​This​ ​is​ ​because​ ​it​ ​is​ ​not
necessary​ ​to​ ​have​ ​an​ ​input​ ​connection​ ​with​ ​the​ ​Signal​ ​Source​ ​function.
7. After​ ​adding​ ​these​ ​functions,​ ​execute​ ​the​ ​flowgraph.​ ​The​ ​radio​ ​station​ ​can​ ​be​ ​changed​ ​by​ ​moving​ ​the
channel_freq​ ​slider.
a. If​ ​no​ ​peak​ ​shows​ ​up​ ​initially,​ ​start​ ​slowly​ ​moving​ ​the​ ​slider​ ​to​ ​search​ ​for​ ​the​ ​signal.​ ​Once​ ​found,
set​ ​the​ ​center​ ​frequency​ ​to​ ​this​ ​value​ ​so​ ​it​ ​doesn’t​ ​have​ ​to​ ​be​ ​searched​ ​for​ ​again.
8. To​ ​add​ ​an​ ​additional​ ​slider​ ​to​ ​control​ ​volume,​ ​delete​ ​the​ ​arrow​ ​connecting​ ​the​ ​WBFM​ ​Receive​ ​function
to​ ​the​ ​Audio​ ​Sink​ ​function.

HackRF​ ​One
Page​ ​17​ ​of​ ​34
 9. Add​ ​a​ ​Multiply​ ​Const​ ​block,​ ​which,​ ​instead​ ​of​ ​multiplying​ ​two​ ​values​ ​from​ ​two​ ​different​ ​blocks,​ ​it​ ​will
multiply​ ​the​ ​input​ ​value​ ​by​ ​the​ ​value​ ​set​ ​within​ ​this​ ​block.
a. Notice​ ​that​ ​the​ ​Multiply​ ​Const​ ​block​ ​has​ ​blue​ ​inputs​ ​and​ ​outputs,​ ​while​ ​the​ ​WBFM​ ​Receive​ ​block
has​ ​an​ ​orange​ ​output.​ ​The​ ​easiest​ ​way​ ​to​ ​change​ ​from​ ​Complex​ ​to​ ​Float​ ​inputs​ ​and​ ​outputs​ ​is​ ​to
click​ ​on​ ​the​ ​block​ ​and​ ​press​ ​the​ ​keyboard’s​ ​down​ ​arrow.​ ​The​ ​input​ ​will​ ​change​ ​from​ ​blue​ ​to
orange​ ​to​ ​green​ ​to​ ​yellow.​ ​Another​ ​way​ ​to​ ​change​ ​the​ ​input​ ​and​ ​output​ ​in​ ​order​ ​to​ ​match​ ​is​ ​to
alter​ ​the​ ​properties​ ​within​ ​the​ ​Multiply​ ​Const​ ​block.​ ​Double​ ​click​ ​the​ ​block​ ​and​ ​change​ ​the​ ​ID
type​ ​from​ ​Complex​ ​to​ ​Float​ ​from​ ​the​ ​drop​ ​down​ ​menu.
b. Connect​ ​the​ ​WBFM​ ​Receive​ ​output​ ​to​ ​the​ ​Multiply​ ​Const​ ​input,​ ​and​ ​the​ ​Multiply​ ​Const​ ​output​ ​to
the​ ​Audio​ ​Sink​ ​input.
c. Set​ ​the​ ​Constant​ ​in​ ​the​ ​Multiply​ ​Const​ ​block​ ​to​ ​audio_gain​.
d. Now,​ ​while​ ​executing​ ​the​ ​flowgraph,​ ​there​ ​will​ ​be​ ​a​ ​slider​ ​at​ ​the​ ​top​ ​of​ ​the​ ​screen​ ​labeled
audio_gain​ ​to​ ​control​ ​the​ ​volume,​ ​along​ ​with​ ​the​ ​channel_freq​ ​slider​ ​to​ ​change​ ​the​ ​radio​ ​station.

Video​ ​3​ ​–​ ​Adding​ ​Functionality​ ​to​ ​the​ ​Receive​ ​File

Transmitting​ ​FM​ ​Radio​ ​Signals

This​ ​section​ ​outlines​ ​how​ ​to​ ​transmit​ ​radio​ ​signals​ ​to​ ​an​ ​open​ ​radio​ ​station​ ​through​ ​the​ ​use​ ​of​ ​the​ ​HackRF​ ​One
device​ ​and​ ​the​ ​GNU​ ​Radio​ ​Companion​ ​software.​ ​This​ ​section​ ​also​ ​contains​ ​a​ ​video​ ​tutorial.
1. Upon​ ​starting​ ​the​ ​GNU​ ​Radio​ ​Companion​ ​software,​ ​there​ ​will​ ​be​ ​two​ ​boxes​ ​already​ ​present​ ​on​ ​the
flowgraph​ ​area:​ ​Variable​ ​and​ ​Options​.​ ​These​ ​default​ ​to​ ​a​ ​set​ ​rate​ ​and​ ​value,​ ​which​ ​can​ ​be​ ​altered,​ ​as
mentioned​ ​above.​ ​In​ ​the​ ​Options​ ​block,​ ​the​ ​Generate​ ​Options​ ​should​ ​be​ ​set​ ​to​ ​QT​ ​GUI​.
2. In​ ​the​ ​Variable​ ​block,​ ​change​ ​the​ ​sample​ ​rate​ ​(​samp_rate​)​ ​to​ ​the​ ​desired​ ​value.​ ​The​ ​lowest
recommended​ ​sample​ ​rate​ ​is​ ​2e6​ ​(2​ ​million),​ ​and​ ​the​ ​highest​ ​recommended​ ​sample​ ​rate​ ​is​ ​20e6​ ​(20
million).​ ​A​ ​good​ ​starting​ ​sample​ ​rate​ ​for​ ​transmitting​ ​radio​ ​signals​ ​is​ ​2e6​ ​(2​ ​million),​ ​and​ ​increase​ ​from
there.​ ​A​ ​computer​ ​with​ ​less​ ​processing​ ​speed​ ​should​ ​not​ ​have​ ​a​ ​high​ ​sample​ ​rate​ ​frequency.​ ​
3. To​ ​even​ ​begin​ ​the​ ​process​ ​of​ ​transmitting​ ​audio​ ​to​ ​an​ ​FM​ ​radio​ ​station​ ​via​ ​the​ ​HRF1​ ​device,​ ​obtain​ ​a​ ​file
source​ ​to​ ​transmit,​ ​such​ ​as​ ​any​ ​available​ ​‘.wav’​ ​audio​ ​file.​ ​Please​ ​note​ ​that​ ​every​ ​‘.wav’​ ​file​ ​may​ ​have​ ​its
own​ ​audio​ ​rate​ ​(for​ ​example,​ ​22050​ ​Hz).​ ​This​ ​can​ ​be​ ​confirmed​ ​by​ ​checking​ ​the​ ​file’s​ ​properties​ ​(by
right-clicking​ ​the​ ​file​ ​in​ ​the​ ​folder​ ​and​ ​checking​ ​its​ ​Properties​ ​>​ ​Audio​ ​>​ ​Sample​ ​rate).
4. In​ ​GRC,​ ​add​ ​the​ ​Wav​ ​File​ ​Source​ ​function​ ​and​ ​place​ ​it​ ​into​ ​the​ ​flowgraph.

HackRF​ ​One
Page​ ​18​ ​of​ ​34
 a. From​ ​the​ ​file​ ​option​ ​within​ ​the​ ​block,​ ​add​ ​the​ ​desired​ ​‘.wav’​ ​file.
5. Add​ ​a​ ​WBFM​ ​Transmit​ ​function​ ​to​ ​the​ ​flowgraph.
a. Set​ ​both​ ​the​ ​Audio​ ​Rate​ ​and​​ ​Quadrature​ ​Rate​ ​to​ ​an​ ​integer​ ​four​ ​times​ ​the​ ​file’s​ ​audio​ ​rate​ ​(for
example,​ ​88200,​ ​which​ ​needs​ ​to​ ​be​ ​an​ ​integer,​ ​not​ ​in​ ​scientific​ ​notation).​ ​This​ ​will​ ​generate​ ​a
clearer​ ​sound​ ​from​ ​the​ ​audio​ ​file​ ​transmitted​ ​from​ ​the​ ​HRF1​ ​without​ ​lowering​ ​the​ ​volume.
b. Set​ ​Tau​ ​to​ ​25e-6.​ ​This​ ​will​ ​increase​ ​volume.
c. Connect​ ​the​ ​WBFM​ ​Transmit​ ​input​ ​to​ ​the​ ​Wav​ ​File​ ​Source​ ​output​ ​with​ ​an​ ​arrow.
6. Next,​ ​add​ ​a​ ​Rational​ ​Resampler​ ​block​ ​to​ ​the​ ​flowgraph.
a. Set​ ​the​ ​Interpolation​ ​value​ ​to​ ​90​ ​in​ ​order​ ​to​ ​decimate​ ​the​ ​sample​ ​rate​ ​to​ ​the​ ​correct​ ​value.​ ​If​ ​the
audio​ ​rate​ ​of​ ​the​ ​.wav​ ​file​ ​is​ ​44100​ ​Hz,​ ​set​ ​the​ ​interpolation​ ​to​ ​45.
7. Obtain​ ​a​ ​QT​ ​GUI​ ​Range​ ​to​ ​determine​ ​the​ ​broadcasting​ ​station.
a. Rename​ ​the​ ​ID​ ​as​ ​freq​.
b. Set​ ​the​ ​Default​ ​Value​ ​and​ ​Start​ ​value​ ​inputs​ ​of​ ​the​ ​desired​ ​radio​ ​station​ ​to​ ​broadcast​ ​(for
example,​ ​87.7e6).​ ​Set​ ​the​ ​Stop​ ​frequency​ ​to​ ​107.7e6,​ ​which​ ​is​ ​the​ ​highest​ ​FM​ ​radio​ ​value.
Additionally,​ ​the​ ​Step​ ​value​ ​represents​ ​the​ ​width​ ​of​ ​each​ ​FM​ ​Radio​ ​channel​ ​in​ ​Step.​ ​Set​ ​this​ ​to
200e3.
8. Add​ ​an​ ​Osmocom​ ​Sink​ ​function,​ ​which​ ​will​ ​allow​ ​the​ ​Hack​ ​RF​ ​to​ ​transmit​ ​the​ ​signals.
a. Set​ ​the​ ​Ch0:​ ​Frequency​ ​to​ ​freq​,​ ​which​ ​will​ ​enable​ ​the​ ​utilization​ ​of​ ​a​ ​slider​ ​within​ ​the​ ​pop​ ​up
window​ ​in​ ​order​ ​to​ ​change​ ​the​ ​broadcast​ ​radio​ ​station.
9. Click​ ​the​ ​play​ ​button​ ​and​ ​save​ ​the​ ​flowgraph​ ​as​ ​a​ ​file.​ ​Upon​ ​executing​ ​the​ ​flowgraph,​ ​a​ ​new​ ​window
will​ ​appear​ ​with​ ​just​ ​the​ ​slider.​ ​The​ ​.wav​ ​file​ ​uploaded​ ​to​ ​the​ ​Wav​ ​File​ ​Source​ ​will​ ​begin​ ​playing.
Depending​ ​on​ ​the​ ​quality​ ​of​ ​the​ ​antennae​ ​used,​ ​the​ ​sound​ ​may​ ​be​ ​slightly​ ​distorted.

Video​ ​4​ ​–​ ​Transmitting​ ​Signals​ ​from​ ​the​ ​Device

HackRF​ ​One
Page​ ​19​ ​of​ ​34
Retransmitting​ ​FM​ ​Radio​ ​Signals
This​ ​section​ ​outlines​ ​the​ ​procedure​ ​to​ ​record​ ​an​ ​audio​ ​sample​ ​from​ ​a​ ​radio​ ​station​ ​and​ ​retransmit​ ​it​ ​to​ ​a​ ​different
radio​ ​station.​ ​This​ ​section​ ​also​ ​contains​ ​a​ ​video​ ​tutorial.
1. First,​ ​follow​ ​the​ ​tutorials​ ​above​ ​or​ ​open​ ​the​ ​previously​ ​saved​ ​files​ ​for​ ​receiving​ ​(which​ ​will​ ​be​ ​referred
to​ ​as​ ​tutorial​ ​1.grc​)​ ​and​ ​transmitting​ ​(which​ ​will​ ​be​ ​referred​ ​to​ ​as​ ​tutorial​ ​2.grc​)​ ​FM​ ​radio​ ​signals.​ ​Open
these​ ​files​ ​in​ ​separate​ ​tabs​ ​of​ ​the​ ​same​ ​window.
2. In​ ​the​ ​tutorial​ ​1​ ​tab,​ ​add​ ​a​ ​Wav​ ​File​ ​Sink​ ​function​ ​to​ ​allow​ ​the​ ​signals​ ​received​ ​to​ ​be​ ​saved​ ​as​ ​a​ ​‘.wav’
file.
a. Change​ ​the​ ​file​ ​path​ ​in​ ​the​​ ​File​ ​prompt​ ​to​ ​somewhere​ ​on​ ​the​ ​desktop​ ​(for​ ​example,​ ​an​ ​empty
folder​ ​on​ ​the​ ​desktop).
b. Change​ ​the​ ​number​ ​of​ ​channels​ ​(​N​ ​Channels​)​ ​to​ ​2.​ ​This​ ​value​ ​needs​ ​to​ ​be​ ​2​ ​in​ ​order​ ​to​ ​double
the​ ​number​ ​of​ ​samples​ ​to​ ​successfully​ ​save​ ​the​ ​file.​ ​This​ ​will​ ​enable​ ​the​ ​Wav​ ​File​ ​Sink​ ​function
to​ ​have​ ​2​ ​inputs.
c. Set​ ​the​ ​Sample​ ​Rate​ ​to​ ​48000.
d. Connect​ ​one​ ​of​ ​the​ ​inputs​ ​of​ ​the​ ​Wav​ ​File​ ​Sink​ ​to​ ​the​​ ​Multiply​ ​Const​.
3. Obtain​ ​a​ ​Constant​ ​Source​ ​function​,​ ​and​ ​set​ ​the​ ​value​ ​to​ ​0.​ ​This​ ​will​ ​keep​ ​the​ ​values​ ​within​ ​the​ ​.wav​ ​as
real​ ​numbers.
a. Connect​ ​the​ ​second​ ​Wav​ ​File​ ​Sink​ ​input​ ​to​ ​the​ ​Constant​ ​Source​ ​output.
4. Execute​ ​the​ ​flowgraph​ ​for​ ​about​ ​10​ ​seconds.​ ​GRC​ ​will​ ​immediately​ ​begin​ ​recording​ ​the​ ​audio​ ​sample.​ ​It
is​ ​recommended​ ​to​ ​only​ ​play​ ​the​ ​flowgraph​ ​for​ ​a​ ​few​ ​seconds​ ​because​ ​.wav​ ​files​ ​can​ ​become​ ​very​ ​large,
very​ ​fast.
a. Again,​ ​a​ ​reminder​ ​to​ ​close​ ​the​ ​flowgraph​ ​via​ ​the​ ​red​ ​x​ ​in​ ​the​ ​upper​ ​left-hand​ ​corner​ ​of​ ​the
flowgraph​ ​window,​ ​not​ ​the​ ​red​ ​x​ ​by​ ​the​ ​play​ ​button.​ ​Otherwise,​ ​the​ ​.wav​ ​file​ ​will​ ​not​ ​save
properly.
5. Now,​ ​in​ ​the​ ​tab​ ​containing​​ ​tutorial​ ​2​,​ ​from​ ​the​ ​Wav​ ​File​ ​Source​ ​function,​ ​select​ ​the​ ​recorded​ ​filename
from​ ​Tutorial​ ​1​ ​as​ ​the​ ​desired​ ​file​ ​to​ ​transmit​.

HackRF​ ​One
Page​ ​20​ ​of​ ​34
 6. Change​ ​the​ ​Interpolation​ ​value​ ​in​ ​the​ ​Rational​ ​Resampler​ ​function​​ ​to​ ​45.​ ​This​ ​is​ ​half​ ​of​ ​the​ ​previous
Interpolation​ ​value​ ​of​ ​90.​ ​This​ ​will​ ​prevent​ ​the​ ​file​ ​from​ ​sounding​ ​sped​ ​up​ ​or​ ​slowed​ ​down,​ ​since​ ​the
sample​ ​rate​ ​of​ ​the​ ​recorded​ ​.wav​ ​file​ ​is​ ​different​ ​from​ ​the​ ​WBFM​ ​Transmit​ ​Audio​ ​Rate​.
7. Now,​ ​by​ ​executing​ ​the​ ​flowgraph,​ ​the​ ​received​ ​file​ ​recorded​ ​from​ ​tutorial​ ​1​ ​should​ ​play​ ​to​ ​any​ ​radio
near​ ​the​ ​HRF1​ ​antenna.​ ​That​ ​concludes​ ​the​ ​tutorial​ ​to​ ​retransmit​ ​FM​ ​radio​ ​files​ ​via​ ​the​ ​HRF1.

Video​ ​5​ ​–​ ​Retransmitting​ ​Signals​ ​from​ ​the​ ​Device

Live​ ​Broadcasting​ ​FM​ ​Radio​ ​Signals

1. In​ ​order​ ​to​ ​live​ ​broadcast,​ ​just​ ​delete​ ​the​ ​Wav​ ​File​ ​Source​ ​function.​ ​Replace​ ​it​ ​with​ ​the​ ​Audio​ ​Source
function.​ ​This​ ​enables​ ​the​ ​computer’s​ ​sound​ ​card,​ ​so​ ​instead​ ​of​ ​transmitting​ ​a​ ​recorded​ ​file,​ ​the​ ​audio
played​ ​will​ ​be​ ​any​ ​sound​ ​picked​ ​up​ ​by​ ​the​ ​computer’s​ ​microphone.
a. In​ ​the​ ​Audio​ ​Source​ ​block,​ ​change​ ​the​ ​Sample​ ​Rate​ ​to​ ​44.1​ ​KHz.​ ​This​ ​value​ ​aligns​ ​better​ ​with
the​ ​other​ ​values​ ​in​ ​the​ ​flowgraph.
b. Connect​ ​the​ ​Audio​ ​Source​ ​output​ ​to​ ​the​ ​WBFM​ ​Transmit​ ​input.
2. By​ ​changing​ ​the​ ​Audio​ ​Source​ ​>​ ​Sample​ ​Rate​,​ ​the​ ​Variable​ ​>​ ​Sample​ ​Rate​ ​should​ ​also​ ​be​ ​changed​ ​to
44100.
3. Set​ ​the​ ​osmocom​ ​Sink​ ​>​ ​Sample​ ​Rate​ ​back​ ​to​ ​2000000​ ​(2M).​ ​Doing​ ​this​ ​will​ ​unlink​ ​the​ ​default
samp_rate​ ​within​ ​the​ ​function​ ​to​ ​the​ ​Variable​ ​block.​ ​These​ ​two​ ​values​ ​need​ ​to​ ​be​ ​different​ ​because​ ​the
signal​ ​will​ ​not​ ​transmit​ ​correctly​ ​should​ ​the​ ​sample​ ​rate​ ​still​ ​be​ ​linked.
4. Execute​ ​the​ ​flowgraph​ ​and​ ​speak​ ​into​ ​the​ ​computer’s​ ​microphone.​ ​Your​ ​voice​ ​should​ ​be​ ​heard​ ​by
receiving​ ​radios​ ​near​ ​the​ ​HRF1​ ​antenna.

Video​ ​6​ ​–​ ​http://bit.ly/2jsLXTn​​ ​-​ ​Retransmitting​ ​and​ ​Broadcasting

HackRF​ ​One
Page​ ​21​ ​of​ ​34
 Further​ ​Work
After​ ​documenting​ ​its​ ​setup,​ ​use,​ ​and​ ​functionality,​ ​our​ ​team​ ​proceeded​ ​to​ ​further​ ​research​ ​practical
applications​ ​of​ ​the​ ​HackRF​ ​One.​ ​We​ ​found​ ​our​ ​research​ ​can​ ​be​ ​applied​ ​to​ ​a​ ​number​ ​of​ ​different​ ​radio​ ​spectrums
and​ ​devices.​ ​For​ ​example,​ ​we​ ​explored​ ​modern​ ​technologies​ ​and​ ​consumer​ ​products​ ​that​ ​utilize​ ​radio​ ​frequency
such​ ​as:​ ​Key​ ​Fobs​ ​from​ ​automobiles,​ ​NFC,​ ​and​ ​Bluetooth​ ​CR/LE.

In​ ​terms​ ​of​ ​Bluetooth,​ ​we​ ​learned​ ​about​ ​the​ ​processing​ ​of​ ​signals​ ​like​ ​frequency​ ​hopping.​ ​This​ ​was​ ​then​ ​studied
in​ ​conjunction​ ​with​ ​the​ ​Ubertooth​ ​One,​ ​a​ ​device​ ​which​ ​specializes​ ​in​ ​the​ ​analysis​ ​of​ ​Bluetooth​ ​signals,​ ​in​ ​order
to​ ​determine​ ​how​ ​to​ ​receive​ ​information​ ​into​ ​the​ ​Hack​ ​RF​ ​One.​ ​As​ ​a​ ​result,​ ​we​ ​were​ ​able​ ​to​ ​record​ ​and​ ​analyze
data​ ​from​ ​devices​ ​that​ ​use​ ​this​ ​wireless​ ​technology.​ ​For​ ​example,​ ​MAC​ ​Address​ ​and​ ​RSSI​ ​information​ ​can​ ​be
used​ ​to​ ​determine​ ​the​ ​distance​ ​of​ ​devices​ ​within​ ​a​ ​vicinity.​ ​These​ ​discovered​ ​devices​ ​can​ ​then​ ​be​ ​exploited​ ​by
transmitting​ ​foreign​ ​data.

With​ ​the​ ​rise​ ​of​ ​consumer​ ​products​ ​that​ ​utilize​ ​wireless​ ​technologies,​ ​the​ ​HackRF​ ​One​ ​is​ ​a​ ​handy​ ​tool​ ​that
allows​ ​the​ ​examination​ ​of​ ​communicating​ ​devices.​ ​We​ ​hope​ ​that​ ​our​ ​research​ ​will​ ​help​ ​others​ ​further​ ​the
practical​ ​application​ ​of​ ​the​ ​HackRF​ ​One​ ​in​ ​future​ ​projects.

HackRF​ ​One
Page​ ​22​ ​of​ ​34
 Appendix

Commonly​ ​Used​ ​Functions​ ​on​ ​GNU​ ​Radio​ ​Companion

1. Osmocom​ ​Source​​ ​[No​ ​module​ ​specified​ ​→​ ​Sources]​ ​–​ ​Allows​ ​the​ ​HackRF​ ​One​ ​to​ ​enter​ ​‘receive​ ​mode’
and​ ​communicate​ ​with​ ​another​ ​device.
a. Sample​ ​rate​​ ​–​ ​Sets​ ​the​ ​number​ ​of​ ​samples​ ​per​ ​second​ ​the​ ​HackRF​ ​One​ ​receives​ ​or​ ​transmits,​ ​by
default​ ​it​ ​is​ ​connected​ ​to​ ​variable​ ​samp_rate​.
b. Ch0​ ​Frequency​ ​–​ ​The​ ​center​ ​frequency​ ​that​ ​the​ ​Osmocom​ ​is​ ​taking​ ​samples​ ​of.
c. Ch0​ ​RF​ ​Gain​ ​(dB)​ ​–​ ​Amplifies​ ​the​ ​strength​ ​of​ ​the​ ​signal,​ ​usually​ ​can​ ​be​ ​set​ ​to​ ​0​ ​without​ ​any
issues.
2. Osmocom​ ​Sink​​ ​[No​ ​module​ ​specified​ ​→​ ​Sinks]​ ​–​ ​Allows​ ​the​ ​HackRF​ ​One​ ​to​ ​enter​ ​‘transmit​ ​mode’​ ​in
order​ ​to​ ​send​ ​out​ ​signals​ ​to​ ​other​ ​devices.
a. Sample​ ​rate​ ​–​ ​Connected​ ​to​ ​samp_rate​,​ ​the​ ​number​ ​of​ ​samples​ ​per​ ​second​ ​the​ ​HackRF​ ​One​ ​is
receiving​ ​or​ ​transmitting
b. Ch0​ ​Frequency​ ​–​ ​The​ ​frequency​ ​that​ ​the​ ​HackRF​ ​One​ ​is​ ​transmitting​ ​to.
3. QT​ ​GUI​ ​Sink​​ ​[Instrumentation​ ​→​ ​QT]​ ​–​ ​Visualizes​ ​the​ ​signals​ ​in​ ​four​ ​different​ ​graphs:​ ​A​ ​frequency
sink,​ ​a​ ​time​ ​sink,​ ​a​ ​waterfall​ ​sink,​ ​and​ ​a​ ​constellation​ ​sink.​ ​These​ ​can​ ​be​ ​used​ ​individually​ ​on​ ​their​ ​own.
Each​ ​sink​ ​is​ ​explained​ ​below.
a. Center​ ​Frequency​​ ​–​ ​The​ ​frequency​ ​that​ ​the​ ​flowgraph​ ​is​ ​centered​ ​at​ ​on​ ​the​ ​x-axis.
b. Refresh​ ​Rate​​ ​–​ ​How​ ​many​ ​times​ ​per​ ​second​ ​the​ ​graph​ ​updates.​ ​It​ ​can​ ​be​ ​lowered​ ​to​ ​increase
performance​ ​on​ ​slower​ ​computers.
4. QT​ ​GUI​ ​Frequency​ ​Sink​​ ​(WX​ ​FFT​ ​Sink)​ ​[Instrumentation​ ​→​ ​QT]​ ​–​ ​Visualizes​ ​signals​ ​as​ ​a​ ​waveform.
The​ ​x-axis​ ​is​ ​the​ ​frequency​ ​of​ ​the​ ​signal​ ​(measured​ ​in​ ​Hz)​ ​and​ ​the​ ​y-axis​ ​is​ ​the​ ​power​ ​of​ ​the​ ​signal
(measured​ ​in​ ​dB).
a. Center​ ​Frequency​​ ​–​ ​Sets​ ​what​ ​frequency​ ​is​ ​at​ ​the​ ​center​ ​of​ ​the​ ​graph.
b. Bandwidth​​ ​–​ ​Sets​ ​the​ ​width​ ​of​ ​the​ ​graph.​ ​For​ ​example,​ ​a​ ​bandwidth​ ​of​ ​1,000​ ​with​ ​a​ ​center
frequency​ ​of​ ​0​ ​Hz​ ​would​ ​show​ ​the​ ​range​ ​of​ ​signals​ ​from​ ​-500​ ​Hz​ ​to​ ​500​ ​Hz.

HackRF​ ​One
Page​ ​23​ ​of​ ​34
 5. QT​ ​Time​ ​Sink​​ ​(WX​ ​GUI​ ​Scope​ ​Sink)​ ​[Instrumentation​ ​→​ ​QT]​ ​–​ ​Visualizes​ ​signals​ ​over​ ​an​ ​x-axis​ ​of
time​ ​and​ ​a​ ​y-axis​ ​of​ ​count​ ​(from​ ​1​ ​to​ ​-1).​ ​Useful​ ​for​ ​measuring​ ​the​ ​power​ ​of​ ​signals​ ​and​ ​seeing​ ​how​ ​long
a​ ​transmission​ ​of​ ​a​ ​signal​ ​is.
6. QT​ ​Constellation​ ​Sink​​ ​[Instrumentation​ ​→​ ​QT]​ ​–​ ​Shows​ ​signals​ ​represented​ ​by​ ​points​ ​on​ ​a​ ​complex
number​ ​scale,​ ​with​ ​the​ ​real​ ​number​ ​component​ ​as​ ​the​ ​x-axis​ ​and​ ​the​ ​imaginary​ ​number​ ​component​ ​as
the​ ​y-axis.
a. Number​ ​of​ ​points​​ ​–​ ​Sets​ ​how​ ​many​ ​points​ ​are​ ​on​ ​the​ ​screen​ ​at​ ​a​ ​given​ ​time.
7. QT​ ​Waterfall​ ​Sink​​ ​[Instrumentation​ ​→​ ​QT]​ ​–​ ​Visualizes​ ​signals​ ​over​ ​a​ ​waterfall,​ ​which​ ​is​ ​a​ ​three
variable​ ​graph.​ ​The​ ​x-axis​ ​is​ ​the​ ​frequency,​ ​the​ ​y-axis​ ​is​ ​time,​ ​and​ ​the​ ​color​ ​of​ ​the​ ​waterfall​ ​is​ ​the
amplitude​ ​of​ ​the​ ​signal​ ​(white​ ​being​ ​the​ ​highest​ ​amplitude,​ ​dark​ ​blue​ ​being​ ​the​ ​lowest).
a. Center​ ​Frequency​​ ​–​ ​The​ ​frequency​ ​set​ ​to​ ​be​ ​at​ ​the​ ​center​ ​of​ ​the​ ​waterfall.
b. Bandwidth​ ​–​ ​Sets​ ​the​ ​width​ ​of​ ​the​ ​graph.​ ​For​ ​example,​ ​a​ ​bandwidth​ ​of​ ​1,000​ ​with​ ​a​ ​center
frequency​ ​of​ ​0​ ​Hz​ ​would​ ​show​ ​the​ ​range​ ​of​ ​signals​ ​from​ ​-500​ ​Hz​ ​to​ ​500​ ​Hz.
8. QT​ ​GUI​ ​Range​​ ​(WX​ ​Slider)​ ​[GUI​ ​Widgets​ ​→​ ​QT]​ ​–​ ​Provides​ ​the​ ​ability​ ​to​ ​make​ ​real​ ​time​ ​adjustments
to​ ​a​ ​variable​ ​using​ ​a​ ​slider.
a. ID​​ ​–​ ​A​ ​unique​ ​identifier​ ​for​ ​the​ ​block.​ ​Set​ ​any​ ​value​ ​in​ ​another​ ​block​ ​to​ ​this​ ​ID​ ​instead​ ​of​ ​a
number​ ​to​ ​utilize​ ​the​ ​slider.​ ​The​ ​name​ ​of​ ​the​ ​ID​ ​will​ ​also​ ​be​ ​how​ ​it​ ​appears​ ​in​ ​the​ ​GUI​ ​when​ ​the
program​ ​is​ ​running.
b. Default​ ​Value​​ ​–​ ​The​ ​value​ ​that​ ​will​ ​be​ ​used​ ​when​ ​the​ ​program​ ​is​ ​first​ ​started.
c. Start/Stop​​ ​–​ ​The​ ​minimum​ ​and​ ​maximum​ ​values,​ ​respectively,​ ​that​ ​the​ ​slider​ ​can​ ​go​ ​to.
d. Step​​ ​–​ ​The​ ​amount​ ​that​ ​the​ ​slider​ ​changes​ ​by​ ​with​ ​each​ ​tick.​ ​For​ ​example,​ ​if​ ​the​ ​step​ ​was​ ​5,​ ​then
the​ ​slider​ ​would​ ​only​ ​move​ ​in​ ​increments​ ​of​ ​5.
9. Signal​ ​Source​​ ​[Waveform​ ​Generators]​ ​–​ ​Provides​ ​a​ ​constant​ ​signal​ ​at​ ​a​ ​specified​ ​frequency.
a. Waveform​​ ​–​ ​Sets​ ​the​ ​type​ ​of​ ​signal​ ​being​ ​created.​ ​The​ ​default​ ​waveform​ ​is​ ​cosine..
b. Frequency​​ ​–​ ​Indicates​ ​what​ ​frequency​ ​the​ ​signal​ ​will​ ​be​ ​transmitting​ ​at.
c. Amplitude​​ ​–​ ​Sets​ ​the​ ​strength​ ​of​ ​the​ ​generated​ ​signal.
10. Low​ ​Pass​ ​Filter​​ ​[Filters]​ ​–​ ​Helps​ ​to​ ​clear​ ​out​ ​noise​ ​from​ ​the​ ​instrumentation​ ​sinks.​ ​It​ ​helps​ ​peaks​ ​stand
out​ ​and​ ​gets​ ​rid​ ​of​ ​noise​ ​that​ ​could​ ​interfere​ ​with​ ​signals.
a. Cutoff​ ​Frequency​​ ​–​ ​Sets​ ​how​ ​wide​ ​the​ ​non-filtered​ ​section​ ​is.​ ​A​ ​higher​ ​value​ ​means​ ​a​ ​wider
band​ ​of​ ​signals​ ​not​ ​filtered​ ​out.

HackRF​ ​One
Page​ ​24​ ​of​ ​34
 b. Transition​ ​Width​​ ​–​ ​Controls​ ​how​ ​steep​ ​the​ ​transition​ ​from​ ​filtered​ ​to​ ​not​ ​filtered​ ​signals​ ​is.​ ​A
low​ ​value​ ​means​ ​a​ ​quicker​ ​and​ ​steeper​ ​transition.
11. Quadrature​ ​Demod​​ ​[Modulators]​ ​–​ ​A​ ​complex​ ​to​ ​float​ ​converter​ ​that​ ​combines​ ​both​ ​the​ ​real​ ​and
imaginary​ ​component​ ​of​ ​a​ ​complex​ ​number​ ​into​ ​a​ ​single​ ​float.
a. Gain​​ ​–​ ​Set​ ​to​ ​1,​ ​and​ ​by​ ​default​ ​is​ ​a​ ​variable​ ​with​ ​definitions​ ​typically​ ​not​ ​present​ ​in​ ​the
flowgraph.
12. Throttle​​ ​[Misc.]​ ​–​ ​Limits​ ​the​ ​data​ ​throughput​ ​to​ ​the​ ​specified​ ​sampling​ ​rate.​ ​This​ ​prevents​ ​GNU​ ​Radio
from​ ​consuming​ ​all​ ​CPU​ ​resources.
13. Float​ ​to​ ​Complex​ ​[Type​ ​Converters]​ ​–​ ​Converts​ ​a​ ​complex​ ​number​ ​into​ ​its​ ​real​ ​and​ ​imaginary​ ​parts,
providing​ ​a​ ​separate​ ​output​ ​for​ ​each​ ​part.​ ​Only​ ​one​ ​of​ ​the​ ​outputs​ ​needs​ ​to​ ​be​ ​connected​ ​for​ ​the​ ​block
work,​ ​but​ ​both​ ​can​ ​be​ ​used.
14. DC​ ​Blocker​ ​[Filters]​ ​–​ ​Filters​ ​out​ ​the​ ​direct​ ​current​ ​voltage​ ​that​ ​is​ ​going​ ​into​ ​the​ ​HackRF​ ​One.​ ​If​ ​there
is​ ​not​ ​a​ ​DC​ ​Blocker,​ ​there​ ​will​ ​be​ ​a​ ​spike​ ​in​ ​the​ ​middle​ ​of​ ​the​ ​graph​ ​that​ ​could​ ​be​ ​confused​ ​with​ ​an
actual​ ​radio​ ​signal.​ ​Always​ ​set​ ​the​ ​value​ ​of​ ​the​ ​DC​ ​blocker​ ​to​ ​1024.
15. (WAV)​ ​File​ ​Sink​ ​[File​ ​Operators]​ ​–​ ​Saves​ ​raw​ ​digital​ ​waveform​ ​information​ ​coming​ ​from​ ​the​ ​Hack​ ​RF
(connect​ ​to​ ​Osmocom​ ​Source)​ ​into​ ​a​ ​file​ ​(specific​ ​path,​ ​set​ ​within​ ​block)​ ​without​ ​processing​ ​it​ ​further.​ ​It
can​ ​also​ ​be​ ​saved​ ​as​ ​an​ ​audio​ ​file​ ​(in​ ​.wav​ ​format).​ ​**​Caution!​ ​The​ ​size​ ​of​ ​the​ ​file​ ​can​ ​become​ ​big​ ​very
quickly,​ ​only​ ​use​ ​the​ ​HackRF​ ​One​ ​in​ ​conjunction​ ​with​ ​a​ ​file​ ​sink​ ​for​ ​a​ ​few​ ​seconds.
16. (WAV)​ ​File​ ​Source​ ​[File​ ​Operators]​ ​–​ ​Runs​ ​the​ ​file​ ​from​ ​File​ ​Sink​ ​in​ ​a​ ​new​ ​flowgraph.​ ​Specify
whether​ ​the​ ​process​ ​is​ ​repeated,​ ​over​ ​a​ ​period​ ​of​ ​time,​ ​or​ ​not.​ ​Can​ ​also​ ​be​ ​a​ ​.wav​ ​file.
17. Multiply​ ​[Math​ ​Operators]​ ​–​ ​Multiplies​ ​two​ ​signals​ ​by​ ​one​ ​another.
18. Multiply​ ​Const.​ ​[Math​ ​Operators]​ ​–​ ​Multiplies​ ​input​ ​by​ ​a​ ​constant​ ​into​ ​an​ ​output,​ ​set​ ​the​ ​constant
within​ ​the​ ​block​ ​itself.
19. WBFM​ ​Receive​ ​[Modulators]​ ​–​ ​FM​ ​demodulator,​ ​turns​ ​FM​ ​radio​ ​signals​ ​into​ ​audio​ ​signals.​ ​Note​ ​that
this​ ​is​ ​a​ ​Complex​ ​to​ ​Float​ ​converter​ ​with​ ​one​ ​output.
a. Quadrature​ ​Rate​ ​–​ ​The​ ​rate​ ​that​ ​signals​ ​are​ ​coming​ ​into​ ​the​ ​block,​ ​it​ ​should​ ​be​ ​sent​ ​to​ ​whatever
the​ ​sample​ ​rate​ ​is​ ​at​ ​the​ ​time​ ​of​ ​coming​ ​into​ ​the​ ​block.
b. Decimation​ ​–​ ​Divides​ ​the​ ​sample​ ​rate​ ​by​ ​the​ ​specified​ ​integer.
20. WBFM​ ​Transmit​​ ​[Modulators]​ ​–​ ​FM​ ​modulator,​ ​turns​ ​an​ ​audio​ ​source​ ​into​ ​an​ ​FM​ ​signal​ ​that​ ​can​ ​be
broadcasted​ ​to​ ​an​ ​FM​ ​radio​ ​station.

HackRF​ ​One
Page​ ​25​ ​of​ ​34
 a. Audio​ ​Rate​​ ​-​ ​The​ ​rate​ ​that​ ​samples​ ​are​ ​sent​ ​to​ ​the​ ​sound​ ​card​ ​in​ ​the​ ​computer.
b. Quadrature​ ​Rate​​ ​–​ ​The​ ​rate​ ​that​ ​samples​ ​are​ ​coming​ ​into​ ​the​ ​block.​ ​In​ ​a​ ​WBFM​ ​Transmit
block​ ​it​ ​must​ ​have​ ​a​ ​number​ ​that​ ​is​ ​equal​ ​to​ ​the​ ​Audio​ ​Rate​ ​divided​ ​by​ ​an​ ​integer.
21. Audio​ ​Sink​​ ​[Audio]​ ​–​ ​Allows​ ​user​ ​to​ ​listen​ ​to​ ​signals​ ​within​ ​GRC.​ ​The​ ​sample​ ​rate​ ​should​ ​be​ ​set​ ​to​ ​the
audio​ ​rate​ ​of​ ​the​ ​source​ ​that​ ​is​ ​being​ ​listened​ ​to.
22. Rational​ ​Resampler​ ​[Resamplers]​ ​–​ ​Changes​ ​the​ ​sample​ ​rate​ ​by​ ​a​ ​ratio.​ ​The​ ​sample​ ​rate​ ​is​ ​multiplied
by​ ​the​ ​interpolation​ ​and​ ​then​ ​divided​ ​by​ ​the​ ​decimation​ ​in​ ​the​ ​same​ ​block.​ ​This​ ​is​ ​helpful​ ​because​ ​GRC
only​ ​allows​ ​for​ ​interpolating/decimating​ ​the​ ​sample​ ​rate​ ​by​ ​integers.

FCC​ ​ID
Although​ ​the​ ​above​ ​demonstrated​ ​the​ ​use​ ​of​ ​the​ ​HRF1​ ​device​ ​with​ ​FM​ ​Radio​ ​Signals,​ ​there​ ​are​ ​also
capabilities​ ​to​ ​receive​ ​and​ ​transmit​ ​along​ ​other​ ​signals.​ ​It​ ​is​ ​important​ ​to​ ​note​ ​that​ ​other​ ​devices,​ ​other​ ​than​ ​the
FM​ ​Radio​ ​Tuner,​ ​will​ ​more​ ​than​ ​likely​ ​operate​ ​along​ ​these​ ​other​ ​signals​ ​of​ ​varying​ ​frequencies.
The​ ​FCC​ ​ID​​ ​of​ ​the​ ​other​ ​device​ ​will​ ​be​ ​needed​ ​to​ ​obtain​ ​information​ ​about​ ​the​ ​device​ ​such​ ​as​ ​its​ ​radio
frequencies​ ​and​ ​documents​ ​available​ ​to​ ​the​ ​public​ ​about​ ​the​ ​operation​ ​of​ ​the​ ​device.​​ ​Most​ ​devices​ ​have​ ​been
reviewed​ ​and​ ​tested​ ​by​ ​the​ ​Federal​ ​Communications​ ​Commission,​ ​and​ ​this​ ​information​ ​will​ ​be​ ​available​ ​via
“fcc.gov”.​ ​Assuming​ ​that​ ​the​ ​chosen​ ​device​ ​has​ ​been​ ​reviewed​ ​and​ ​tested​ ​by​ ​the​ ​Federal​ ​Communications
Commission,​ ​the​ ​FCC​ ​ID​ ​will​ ​give​ ​information​ ​on​ ​the​ ​frequency​ ​that​ ​the​ ​device​ ​operates​ ​on,​ ​pictures​ ​of​ ​the
interior​ ​of​ ​the​ ​device,​ ​and​ ​more​ ​useful​ ​information.
1. A​ ​good​ ​test​ ​device​ ​is​ ​something​ ​simple​ ​that​ ​has​ ​a​ ​clear​ ​on​ ​and​ ​off​ ​key​ ​that​ ​transmits​ ​signals.​ ​For
example,​ ​car​ ​keys,​ ​a​ ​garage​ ​door​ ​opener,​ ​a​ ​TV​ ​remote,​ ​etc.
2. Proceed​ ​through​ ​the​ ​following​ ​options:
a. Assuming​ ​that​ ​the​ ​chosen​ ​device​ ​has​ ​been​ ​reviewed​ ​and​ ​tested​ ​by​ ​the​ ​Federal​ ​Communications
Commission​,​ ​enter​ ​‘fcc.gov’​​ ​into​ ​the​ ​URL​ ​bar​ ​of​ ​the​ ​browser​ ​to​ ​access​ ​the​ ​database.
i. Proceed​ ​through​ ​the​ ​following​ ​options:​ ​Licensing​ ​and​ ​Databases​​ ​→​ ​Databases​ ​→
Equipment​ ​Authorization​ ​Search

HackRF​ ​One
Page​ ​26​ ​of​ ​34
 Figure​ ​12:​ ​(Equip.​ ​Auth.​ ​Search)

HackRF​ ​One
Page​ ​27​ ​of​ ​34
 b. Input​ ​the​ ​FCC​ ​ID​ ​into​ ​the​ ​search​ ​box.
i. Depending​ ​on​ ​the​ ​manufacturer,​ ​this​ ​will​ ​differ​ ​on​ ​location,​ ​but​ ​will​ ​generally​ ​be​ ​clearly
defined​ ​and​ ​found​ ​on​ ​the​ ​outer​ ​layer​ ​of​ ​the​ ​physical​ ​device.

HackRF​ ​One
Page​ ​28​ ​of​ ​34
 ii. Enter​ ​the​ ​Grantee​ ​Code​​ ​and​ ​Product​ ​Code,​​ ​click​ ​on​ ​‘Start​ ​Search’,​ ​and​ ​proceed​ ​to​ ​the
product's​ ​‘detail​ ​summary’​ ​and​ ​view​ ​the​ ​‘User​ ​Manual’.
1. If​ ​there​ ​is​ ​more​ ​than​ ​one​ ​option​ ​for​ ​the​ ​device,​ ​check​ ​the​ ​external​ ​photographs​ ​to
see​ ​which​ ​one​ ​matches​ ​the​ ​physical​ ​device.​ ​The​ ​operating​ ​frequencies​ ​will​ ​be
listed​ ​to​ ​the​ ​right​ ​of​ ​each​ ​device​ ​listing.

HackRF​ ​One
Page​ ​29​ ​of​ ​34
HackRF​ ​One
Page​ ​30​ ​of​ ​34
 c. If​ ​the​ ​FCC​ ​ID​ ​cannot​ ​be​ ​found​ ​on​ ​the​ ​device,​ ​it​ ​can​ ​be​ ​searched​ ​by​ ​the​ ​manufacturer.​ ​Underneath
Equipment​ ​Authorization​ ​Search,​ ​there​ ​is​ ​Equipment​ ​Authorization​ ​System​ ​Grantee​ ​Search.
i. Click​ ​on​ ​detail.​ ​There​ ​should​ ​be​ ​a​ ​list​ ​of​ ​documents​ ​relating​ ​to​ ​that​ ​device.​ ​The​ ​user
manual​ ​is​ ​the​ ​document​ ​most​ ​likely​ ​to​ ​list​ ​the​ ​frequencies​ ​which​ ​the​ ​device​ ​functions​ ​on.

HackRF​ ​One
Page​ ​31​ ​of​ ​34
HackRF​ ​One
Page​ ​32​ ​of​ ​34
 References
Amplitude​ ​modulation.​ ​(2017,​ ​November​ ​05).​ ​Retrieved​ ​from
https://en.wikipedia.org/wiki/Amplitude_modulation
ANT500.​ ​(n.d.)​ ​Retrieved​ ​from
https://greatscottgadgets.com/ant500/
Christensson,​ ​P.​ ​(2015,​ ​August​ ​22).​ ​Sample​ ​Rate.​ ​Retrieved​ ​from
https://techterms.com/definition/sample_rate
FAQ.​ ​(n.d.)​ ​Retrieved​ ​from​ ​the​ ​HackRF​ ​Wiki:
https://github.com/mossmann/hackrf/wiki/FAQ
GNU​ ​Radio​ ​Companion.​ ​(n.d.).​ ​Retrieved​ ​from​ ​the​ ​GNU​ ​Radio​ ​Wiki:
https://wiki.gnuradio.org/index.php/GNURadioCompanion
Georgia​ ​State​ ​University.​ ​(n.d.).​ ​[AM/FM​ ​Radio​ ​Waves​ ​Visual].​ ​Retrieved​ ​from
http://springfield.gsu.edu/omeka/files/fullsize/6f4be87348f12211687c2529d8be5387.jpg
Getting​ ​Started​ ​with​ ​the​ ​HackRF​ ​and​ ​GNU​ ​Radio.​ ​(n.d.).​ ​Retrieved​ ​from​ ​the​ ​HackRF​ ​Wiki:
https://github.com/mossmann/hackrf/wiki/Getting-Started-with-HackRF-and-GNU-Radio
Guided​ ​Tutorial​ ​GRC.​ ​(n.d.).​ ​Retrieved​ ​from​ ​the​ ​GNU​ ​Radio​ ​Wiki:
https://wiki.gnuradio.org/index.php/Guided_Tutorial_GRC
Guided​ ​Tutorial​ ​Introduction.​ ​(n.d.).​ ​Retrieved​ ​from​ ​the​ ​GNU​ ​Radio​ ​Wiki:
https://wiki.gnuradio.org/index.php/Guided_Tutorial_Introduction
HackRF​ ​One.​ ​(n.d.).​ ​Retrieved​ ​from​ ​the​ ​HackRF​ ​Wiki:
https://github.com/mossmann/hackrf/wiki/HackRF-One
Low-pass​ ​filter.​ ​(2017,​ ​November​ ​07).​ ​Retrieved​ ​from​ ​https://en.wikipedia.org/wiki/Low-pass_filter
Northwestern​ ​University.​ ​(n.d.).​ ​How​ ​is​ ​data​ ​put​ ​on​ ​radio​ ​waves?​ ​Retrieved​ ​from
http://www.qrg.northwestern.edu/projects/vss/docs/communications/1-how-is-data-put-on-radio-waves.
html
Northwestern​ ​University.​ ​(n.d.).​ ​What​ ​are​ ​radio​ ​waves?​ ​Retrieved​ ​from
http://www.qrg.northwestern.edu/projects/vss/docs/communications/1-what-are-radio-waves.html
Ossmann,​ ​M.​ ​(2014).​ ​Software​ ​Defined​ ​Radio​ ​with​ ​HackRF​ ​Lessons​ ​1-11​ ​[Videos].​ ​Retrieved​ ​from
https://greatscottgadgets.com/sdr/

HackRF​ ​One
Page​ ​33​ ​of​ ​34
Ossmann,​ ​M.​ ​(n.d.).​ ​HackRF​ ​One​.​ ​Retrieved​ ​from
https://greatscottgadgets.com/hackrf/
Radio​ ​frequency.​ ​(n.d.).​ ​In​ ​Merriam-Webster​.​ ​Retrieved​ ​from
https://www.merriam-webster.com/dictionary/radio%20frequency
Radio​ ​receiver.​ ​(2017,​ ​November​ ​09).​ ​Retrieved​ ​from​ ​https://en.wikipedia.org/wiki/Radio_receiver
Rouse,​ ​M.​ ​(n.d.).​ ​What​ ​is​ ​digital​ ​signal​ ​processing​ ​(DSP)?​ ​-​ ​Definition​ ​from​ ​WhatIs.com.​ ​Retrieved​ ​from
http://whatis.techtarget.com/definition/digital-signal-processing-DSP
Rouse,​ ​M.​ ​(n.d.).​ ​What​ ​is​ ​software-defined​ ​radio​ ​(SDR)?​ ​-​ ​Definition​ ​from​ ​WhatIs.com.​ ​Retrieved​ ​from
http://searchnetworking.techtarget.com/definition/software-defined-radio
Transmit.​ ​(2014).​ ​In​ ​Collins​ ​English​ ​Dictionary​ ​–​ ​Complete​ ​and​ ​Unabridged,​ ​12th​ ​Edition​ ​2014​.​ ​Retrieved
from​ ​https://www.thefreedictionary.com/transmit

HackRF​ ​One
Page​ ​34​ ​of​ ​34