Bolted Exterior Body Panels and Closures

Document ID: 1749013 Page 1 of 1
2009 Saturn VUE - AWD | VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual | Body Repair |
Bolted Exterior Body Panels and Closures | Specifications | Document ID: 1749013
Fastener Tightening Specifications

Specification
Application Metric English
Fuel Filler Door Bolts 2.5 N·m 22 lb in
Front Door Check Link Bolts 10 N·m 89 lb in
Front Door Check Link to Body 20 N·m 15 lb ft
Front Door Hinge To Body Bolts 36 N·m 27 lb ft
Front Door Hinge To Door Bolts 25 N·m 18 lb ft
Front Fender Bolts 9 N·m 80 lb in
Front Outer Door Panel Bolts 8 N·m 71 lb in
Hood Hinge Bolts 25 N·m 18 lb ft
Hood Latch Bolts 10 N·m 89 lb in
Liftgate Hinge Bolts 25 N·m 18 lb ft
Liftgate Hinge Nuts 25 N·m 18 lb ft
Liftgate Strut Anchor 25 N·m 18 lb ft
Quarter Panel Bolts 9 N·m 80 lb in
Quarter Panel Nuts 9 N·m 80 lb in
Rear Door Check Link Bolts 10 N·m 89 lb in
Rear Door Check Link to Body Bolt 20 N·m 15 lb ft
Rear Door Hinge To Body Bolts 36 N·m 27 lb ft
Rear Door Hinge To Door Bolts 25 N·m 18 lb ft
Rear Outer Door Panel Bolts 8 N·m 71 lb in
Hood Latch Release Cable Bolt 9 N·m 80 lb in
Fuel Tank Filler Door Bolt 2.5 N·m 22 lb in
Hood Latch Release Handle Screw 10 N·m 89 lb in
http://localhost:9001/si/showDoc.do?docSyskey=1749013&pubCellSyskey=9265&pubO... 11/15/2010
Bolted Exterior Body Panels and Closures | Repair Instructions | Document ID: 2166688
Hood Primary Latch Release Cable Replacement
Callout Component Name
Preliminary Procedures
1. Remove the headlamps. Refer to Headlamp Replacement.
2. Remove the hood release handle. Refer to Hood Primary Latch Release Cable Handle
Replacement.
3. Remove the front compartment front sight shield. Refer to Front Compartment Sight
Shields Replacement.
Hood Latch Release Cable Bolt (Qty: 2)
Caution: Refer to Fastener Caution in the Preface section.

1
Tighten
9 N·m (80 lb in)
Hood Latch Release Cable
2 Procedure
1. Disconnect the hood release cable from the hood latch by squeezing the hood
release cable
© retainer.
2010 General Motors Corporation. All rights reserved.
2. Attach mechanic's wire to the existing cable to ease installation of the new
cable.
3. Release the cable from the latch assembly and pull through the dash panel.
Front Side Door Adjustment

Warning: In order to prevent SIR deployment, personal injury, or unnecessary SIR system
repairs, do not strike the door or the door pillar in the area of the side impact sensor (SIS).
Turn OFF the ignition and remove the key when performing service in the area of the SIS.
1. Remove the door lock striker. Refer to Front Side Door Lock Striker Replacement.
2. For up, down, forward, or rearward adjustment, loosen the hinge to hinge pillar bolts.
3. Move the door within the door opening to achieve the best alignment and operation.
4. Tighten all of the hinge fasteners that were loosened.
Tighten
Tighten the hinge fasteners to 25 N·m (18 lb ft).
5. Install the striker to the approximate proper position.

6. Adjust the door striker. Refer to Front Side Door Lock Striker Adjustment.
7. Inspect the door weatherstrips for proper fit.
http://localhost:9001/si/showDoc.do?docSyskey=2166693&pubCellSyskey=149890&pub... 11/15/2010
Front Side Door Replacement
1. Disable the supplemental inflatable restraint (SIR) system. Refer to SIR Disabling and
Enabling.
2. Remove the front door trim panel. Refer to Front Side Door Trim Panel Replacement.
3. Remove front door check link bolt. Refer to Front Side Door Check Link Replacement.
Front Side Door Bolt (Qty: 4)

1
Tighten
25 N·m (18 lb ft)
Front Side Door
Procedure
2
1. Remove the water deflector.
2. Support the door before removing the hinge bolts.
3. Disconnect the electrical
© 2010 General connector, if equipped.
Motors Corporation. All rights reserved.
4. With the aid of an assistant, remove the door.

5. If installing new door, transfer all necessary components.
6. Verify door is properly aligned. If door adjustments are needed, refer to Front
Side Door Adjustment.
Rear Side Door Adjustment
1. Remove the door striker. Refer to Rear Side Door Lock Striker Replacement.
2. For up, down, forward, or rearward adjustment, loosen the hinge to hinge pillar bolts.
3. Move the door within the door opening to achieve the best alignment and operation.
4. Tighten all of the hinge fasteners that were loosened.
Tighten
Tighten the hinge fasteners to 25 N·m (18 lb ft).
5. Install the striker to the approximate proper position.

6. Adjust the door striker. Refer to Rear Side Door Lock Striker Adjustment.
7. Inspect the door weatherstrips for proper fit.
Rear Side Door Replacement

Warning: Refer to SIR Warning in the Preface section.
1. Disable the supplemental inflatable restraint (SIR) system. Refer to SIR Disabling and
Enabling.
2. Remove the rear door trim panel. Refer to Rear Side Door Trim Panel Replacement.
3. Remove rear side door check link. Refer to Rear Side Door Check Link Replacement.
Rear Side Door Bolt (Qty: 4)

1
Tighten
25 N·m (18 lb ft)
Rear Side Door Assembly
Procedure
1. Remove the©water deflector.
2010 General Motors Corporation. All rights reserved.
2. Support the door before removing the hinge bolts.

3. Disconnect the electrical connector, if equipped.
4. With the aid of an assistant, remove the door.
2
6. Verify door is properly aligned. If door adjustments are needed, refer to Rear
Door Adjustment.
Front Fender Replacement
1. Remove the bumper fascia. Refer to Front Bumper Fascia Replacement.
2. Remove Front Fender Wheel Opening Molding. Refer to Front Fender Wheel Opening
Molding Replacement.
3. Remove the wheelhouse liner. Refer to Front Wheelhouse Liner Replacement.
4. Remove the rocker panel molding. Refer to Rocker Panel Molding Replacement.
5. Remove the front fender center molding. Refer to Front Fender Center Molding
Replacement.
Front Fender Bolt (Qty: 9)

1
Tighten
9 N·m (80 lb in)
2 Front Fender
Liftgate Adjustment
1. Note the original position of the liftgate latch striker.

2. Remove the striker.
3. Loosen the hinge-to-roof panel bolts for forward or rearward adjustments.
4. If Adjusting hinge to roof panel Bolts. Lower Rear And Headliner if as needed.
5. Loosen the liftgate-to-hinge bolts for up and down adjustment.
6. Move the liftgate within the liftgate opening to achieve the best alignment and operation.
7. Install striker to approximately the proper position.
8. Adjust the striker to achieve the best operation and alignment of the liftgate.
9. Inspect the seals for proper engagement.
10. Tighten the bolts when the proper adjustment is achieved.
Tighten
Tighten the bolts to 25 N·m (18 lb ft).
Liftgate Replacement

Warning: When a lift gate hold open device is being removed or installed, provide alternate
support to avoid the possibility of damage to the vehicle or personal injury.
1. Disconnect the strut rods. Refer to Liftgate Strut Replacement.
2. Remove the rear door upper garnish molding. Refer to Liftgate Garnish Molding
Replacement.
Liftgate Body Side Hinge Bolt (Qty: 4)

1
Tighten
25 N·m (18 lb ft)
Liftgate
2 Procedure
1. Disconnect
© 2010the electrical
General Motors connector.
Corporation. All rights reserved.
2. Transfer part as needed.
Hood Primary Latch Release Cable Handle Replacement

Hood Latch Release Handle Screw (Qty: 2)

1
Tighten
10 N·m (89 lb in)
Hood Latch Release Handle
2
Tip
To release the handle, pull down the cable and unhook from the handle.
Front Side Door Upper Hinge and Lower Hinge

Replacement
1. Remove front fender. Refer to Front Fender Replacement.
2. Remove front door. Refer to Front Side Door Replacement.
3. Remove the insulator pad between the fender and the hinge pillar to remove bolts.
Front Side Door Hinge to Body Bolt (Qty: 4)

1
Tighten
36 N·m (26 lb ft)
Front Side Door Hinge Assembly
Procedure
2. Verify door is properly
© 2010 aligned.
General If door adjustments
Motors Corporation. are needed, refer to Front
All rights reserved.
Side Door Adjustment.
Tip
Support the door during procedure.
2
Use a soft marker to outline around the outside of hinge for install purposes.
When re-installing door, align hinge with marks made during removal procedures.
Hood Hinge Replacement
1. Remove the hood. Refer to Hood Replacement.
2. Remove the front fender. Refer to Front Fender Replacement.
Hood Hinge Bolt (Qty: 4)

1
Tighten
25 N·m (18 lb ft)
Hood Hinge
2
Tip
Adjust the hood hinge, if needed. Refer to Hood Adjustment.
Liftgate Hinge Replacement
1. Remove the liftgate. Refer to Liftgate Replacement.
2. Drop the rear of the headliner to access the bolts. Refer to headliner replacement.
Headlining Trim Panel Replacement.
3. Use a grease pencil to mark the liftgate hinge position to the body prior to removal.
Liftgate Hinge Nut (Qty: 2)

1
Tighten
25 N·m (18 lb ft)
Liftgate Hinge
Procedure
2
• Adjust the liftgate, if needed. Refer to Liftgate Adjustment.

• Inspect the hinge gasket and replace if damaged or torn.
Rear Side Door Upper Hinge and Lower Hinge

Replacement
Removal Procedure
1. Mark around the hinge location with a soft marker for installation alignment purposes.
2. Support the door.
3. With the door fully latched on the striker, remove the hinge to door bolts.
4. Remove the hinge to body bolts and remove the hinges one at a time.
Installation Procedure
1. Position the hinge to the vehicle with the marks made prior to removal.
2. Install the hinge to door bolts.
Tighten
3. Install the hinge to body bolts.
Tighten
4. Inspect the door for proper alignment. Refer to Rear Door Adjustment.
Hood Adjustment
1. Loosen the hinge-to-body bolts to adjust the hood fore and aft, and cross-vehicle. Position
the hood as needed.
2. Adjust the hood latch and hood bumpers to adjust the hood up and down at the front of the
hood.
3. Tighten the hinge and latch bolts.
Tighten
• Tighten the hinge-to-hood bolts to 25 N·m (18 lb ft).
• Tighten the hinge-to-body bolts to 25 N·m (18 lb ft).
• Tighten the hood latch fastener to 25 N·m (18 lb ft).
Hood Replacement

Warning: When a hood hold open device is being removed or installed, provide alternate
Preliminary Procedure
Disconnect the hood strut rod. Refer to Hood Strut Replacement.
Hood Hinge Bolt (Qty: 4)

1
Tighten
25 N·m (18 lb ft)
Hood
2 Tip
• Disconnect any electrical connectors before removing.
• Transfer any parts as needed.
Hood Insulator Replacement

1 Hood Insulator Plastic Retainer (Qty: 11)
2 Hood Insulator
Hood Latch Adjustment

Inspection Procedure
1. Release the primary hood latch in order to inspect the operation of the pop-up spring.
2. Attempt to raise the hood while the hood is in the pop-up position.
• The hood should raise without the hood striker binding against the latch.
• The secondary latch should engage in order to prevent the hood from being raised.
Adjustment Procedure
1. Loosen the bolts retaining the hood latch to the support bracket.
2. Move the hood latch from side to side until the striker enters the center of the latch assembly
and tighten to 10 N·m (89 lb in).
Hood Primary and Secondary Latch Replacement
Remove the front compartment sight shields. Refer to Front Compartment Sight Shields
Replacement.
Hood Latch Mounting Bolt (Qty: 3)

1
Tighten
10 N·m (89 lb in)
Hood Latch Assembly
Procedure
2
1. Disconnect the remote start electrical connector, if equipped.
2. Disconnect the release cable from the hood latch by squeezing the cable
retainer.
Front Side Door Check Link Replacement
1. Remove the front door trim panel. Refer to Front Side Door Trim Panel Replacement.
Front Side Door Check Link to Body Bolt

1
Tighten
20 N·m (18 lb ft)
Front Side Door Check Link Bolt (Qty: 2)
2
Tighten
7 N·m (62 lb in)
Front Side Door Check Link
3
Tip
Remove the check link from the door through the center opening.
Rear Side Door Check Link Replacement
1. Remove the Rear door trim panel. Refer to Rear Side Door Trim Panel Replacement.
Rear Side Door Check Link Body Bolt

1
Tighten
20 N·m (15 lb ft)
Rear Side Door Check Link Bolt (Qty: 2)
2
Tighten
7 N·m (62 lb in)
Rear Side Door Check Link
3
Tip
Remove the check link from the door through the center opening.
Fuel Tank Filler Door Replacement

Fuel Tank Filler Door Bolt (Qty: 2)

1
Tighten
2.5 N·m (22 lb in)
2 Fuel Tank Filler Door
Fuel Tank Filler Door Latch Replacement

Fuel Tank Filler Door Latch Bolt (Qty: 2)
1 Procedure
Disconnect the electrical connector.
Tighten
2.5 N·m (22 lb in)
2 Fuel Tank Filler Door Latch
Fuel Tank Filler Pipe Housing Replacement

Fuel Filler Door Pocket Bolt (Qty: 3)
1 Tip
Remove fuel filler cap.
Tighten
10 N·m (89 lb in)
2 Fuel Filler Door Pocket
Hood Strut Replacement

Warning: When a hood hold open device is being removed or installed, provide alternate
Hood Strut Retainer (Qty: 2)
Procedure
1
1. Release the locking tabs on the strut.
2. Ensure the clip is fully seared when rod is reinstalled. If the clip cannot be
fully seated a new rod should be installed.
2 Hood Strut
Hood Front Weatherstrip Replacement

Hood Front Weatherstrip
1 Procedure
The hood front weatherstrip is held in place with plastic retainers that are part of
the weatherstrip.
Hood Rear Weatherstrip Replacement

Hood Rear Weatherstrip
1 Tip
The hood front weatherstrip is held in place with plastic retainers that are part of
the weatherstrip.
Hood Rear Outer Seal Replacement

Hood Rear Outer Seal
Procedure
1. Clean the area where the seal will be mounted. Use a suitable solvent with a
mixture of 50 percent isopropyl alcohol and 50 percent water by volume, or
high-flash naphtha.
1 2. Warm the hood panel using J 25070 Heat Gun, to a minimum, prior to the
hood rear outer seal installation.
3. Do NOT touch the adhesive surface when tape is removed. Peel the tape liner
off and install the outer rear hood seal.
Special Tools
J 25070 Heat Gun
Front Compartment Sight Shields Replacement

1 Front Compartment Front Sight Shield Plastic Retainer (Qty: 11)
2 Front Compartment Front Sight Shield
Front Side Door Auxiliary Sealing Strip Replacement

Removal Procedure
1. Open the door.

2. Remove the door lower weather-strip from the door.
1. Install the door lower weather-strip.

2. Close door.
Rear Side Door Lower Rear Auxiliary Sealing Strip

Replacement
Removal Procedure
1. Open the door.

2. Remove the door lower weather-strip from the door.
1. Install the door lower weather-strip.

2. Close door.
Liftgate Strut Replacement

Liftgate Strut
Warning: When a lift gate hold open device is being removed or installed, provide
alternate support to avoid the possibility of damage to the vehicle or personal
injury.
Caution: Apply pressure only at the end of the liftgate/hood assist rod that you are
removing or attaching. Do NOT apply pressure to the middle of the rod because
1
damage or bending will result.
Procedure
• Release the locking tabs on the strut.

• Ensure the clip is fully seated when rod is reinstalled. If the clip cannot be
fully seated, a new rod should be installed.
Hood Latch Support Replacement
Remove hood latch. Refer to Hood Primary and Secondary Latch Replacement.
Hood Latch Support Bolt (Qty: 3)

1
Tighten
10 N·m (89 lb in)
2 Hood Latch Support
Front Side Door Weatherstrip Replacement

Removal Procedure
1. Remove the door check link-to-body bolt.
2. Remove the door weatherstrip.
1. Install the door weatherstrip.
2. Install the door check link-to-body bolt.
Tighten
Tighten the door check link-to-body bolt 20 N·m (15 lb ft).
Front Door Opening Weatherstrip Replacement
1. Remove the center pillar lower garnish molding. Refer to Center Pillar Lower Garnish
Molding Replacement
2. Remove the windshield pillar garnish molding. Refer to Windshield Pillar Garnish
Molding Replacement
3. Remove the front door sill plate. Refer to Front Carpet Retainer Replacement .
Front Side Door Opening Weatherstrip
Procedure
1 1. Install the weatherstrip to the pinch-weld flange. Ensure that the weatherstrip
is fully seated.
2. Mark the location of the weatherstrip opening when removing from the pinch
weld.
3. Align the weatherstrip to the door opening with the bond joint positioned at
the lower center of the door opening.
Liftgate Weatherstrip Replacement

Liftgate Weatherstrip
Procedure
1
Clean the area where the seal will be mounted. Use a suitable solvent with a
mixture of 50 percent isopropyl alcohol and 50 percent water by volume, or high-
flash naphtha.
Rear Door Opening Weatherstrip Replacement
1. Remove the center pillar lower garnish molding. Refer to Center Pillar Lower Garnish
Molding Replacement
2. Remove the rear door sill plate. Refer to Rear Carpet Retainer Replacement .
Rear Side Door Opening Weatherstrip
Procedure
1 1. Install the weatherstrip to the pinch-weld flange. Ensure that the weatherstrip
is fully seated.
2. Mark the location of the weatherstrip opening when removing from the pinch
weld.
3. Align the weatherstrip to the door opening with the bond joint positioned at
the lower center of the door opening.

Bolted Exterior Body Panels and Closures

Uploaded by

Copyright:

Available Formats

Bolted Exterior Body Panels and Closures

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Bolted Exterior Body Panels and Closures

Uploaded by

Copyright:

Available Formats

Document ID: 1749013 Page 1 of 1

Fastener Tightening Specifications

Hood Primary Latch Release Cable Replacement

Callout Component Name

Caution: Refer to Fastener Caution in the Preface section.

Hood Latch Release Cable

Front Side Door Adjustment

Caution: Refer to Fastener Caution in the Preface section.

4. Tighten all of the hinge fasteners that were loosened.

5. Install the striker to the approximate proper position.

Front Side Door Replacement

Callout Component Name

Caution: Refer to Fastener Caution in the Preface section.

Front Side Door

4. With the aid of an assistant, remove the door.

Rear Side Door Adjustment

Caution: Refer to Fastener Caution in the Preface section.

4. Tighten all of the hinge fasteners that were loosened.

5. Install the striker to the approximate proper position.

Rear Side Door Replacement

Callout Component Name

Caution: Refer to Fastener Caution in the Preface section.

Rear Side Door Assembly

2. Support the door before removing the hinge bolts.

Front Fender Replacement

Callout Component Name

Caution: Refer to Fastener Caution in the Preface section.

1. Note the original position of the liftgate latch striker.

Caution: Refer to Fastener Caution in the Preface section.

10. Tighten the bolts when the proper adjustment is achieved.

Callout Component Name

Caution: Refer to Fastener Caution in the Preface section.

2. Transfer part as needed.

Hood Primary Latch Release Cable Handle Replacement

Callout Component Name

Caution: Refer to Fastener Caution in the Preface section.

Front Side Door Upper Hinge and Lower Hinge

Callout Component Name

Caution: Refer to Fastener Caution in the Preface section.

Front Side Door Hinge Assembly

Side Door Adjustment.

Hood Hinge Replacement

Callout Component Name

Caution: Refer to Fastener Caution in the Preface section.

Liftgate Hinge Replacement

Callout Component Name

Caution: Refer to Fastener Caution in the Preface section.

• Adjust the liftgate, if needed. Refer to Liftgate Adjustment.

Rear Side Door Upper Hinge and Lower Hinge

Caution: Refer to Fastener Caution in the Preface section.

2. Install the hinge to door bolts.

3. Install the hinge to body bolts.

Caution: Refer to Fastener Caution in the Preface section.

3. Tighten the hinge and latch bolts.

Callout Component Name

Caution: Refer to Fastener Caution in the Preface section.

Hood Insulator Replacement

Callout Component Name

Hood Latch Adjustment

Caution: Refer to Fastener Caution in the Preface section.