MACHINE ROOM.

sdb 25/05/2020

1.24
1.24
1.24
1.24
1.24
1.24
1.24
1.24
1.24
1.24
1.24
1.24

SAP2000 21.0.2 Frame Span Loads (Dead) (GLOBAL CSys) KN, m, C

MACHINE ROOM.sdb 25/05/2020

1.83
1.83
1.83
1.83
1.83
1.83
1.83
1.83
1.83
1.83
1.83
1.83

SAP2000 21.0.2 Frame Span Loads (Live) (GLOBAL CSys) KN, m, C

MACHINE ROOM.sdb 25/05/2020

0.1 0.1
0.1
0.1

1.65
1.65
0.1

1.65
0.1

1.65
0.1

1.65
0.1

1.65
0.1

1.65
0.1

1.65
0.1 0.1

1.65
1.65
1.65
1.65

SAP2000 21.0.2 Frame Span Loads (W) (GLOBAL CSys) KN, m, C

Roof Dead and Live loads and Sidings Dead Load

Location:
Structure:

a. Roof dead loads [NSCP Table 204-1]

roofing = 100 Pa [ Is this an arch or dome?] NO
bracing = 20 Pa [ Are these awnings without cloth cover?] NO
purlins = 80 Pa [ Is this a greenhouse, lath house or agricultural bldg?] NO
ceiling = 200 Pa Roof Type = 1
Others = 50 Pa
total = 450 Pa

b. Self-weight of truss/frame Method 2:

formula: W = (wt/100)aL(1+0.328L) kN Basic live load = 1.00 kPa
formula W = 0.86 kN dead load D = 0.450 kPa
CE Fowler W = 1.37 kN Reduction rate r = 0.08 Table 205-3
self-weight = 0.066 kPa Max reduction Rmax = 0.40 Table 205-3
adopt = 0.00 kPa Reduction R1 = 0.00 [Eqn 205-1]
Reduction R2 = 0.33 [Eqn 205-2]
c. Sidings dead loads Reduction R3 = -0.26 [Eqn 205-3]
sidings = 80 Pa Governing R = 0.33
side girts = 100 Pa Reduced live load = 0.67 kPa
other = 20 Pa
total = 200 Pa

d. Liveload [NSCP 2010 Section 205.4] Summary:

Rise = 0.56 m Roof dead load = 0.688 kN/m @ top chord
Run = 7.50 m 0.550 kN/m @ bottom chord
Span = 7.50 m 1.238 kN/m @ total dead load
Bay dist = 2.75 m
Roof angle θ = 4.25 deg Roof live load = 1.829 kN/m @ top chord
Roof slope = 0.07
Loaded area = 20.63 m2 Siding dead load = 0.550 kN/m @ column
Method 1 = 0.75 kPa
WIND = 0.6 1.65
MACHINE ROOM.sdb 25/05/2020

SAP2000 21.0.2 Axial Force Diagram (D+L) KN, m, C

MACHINE ROOM.sdb 25/05/2020

SAP2000 21.0.2 Axial Force Diagram (0.75(D+L+W)) KN, m, C

MACHINE ROOM.sdb 25/05/2020

SAP2000 21.0.2 Axial Force Diagram (0.75(D+W)) KN, m, C

Project:

Design of Intermediate Purlins Mark : P1

with 1 line of sag rods
wn
roof slope: rise = 0.50 m Trial Section : LC 100x50x15x3.0
run = 5.50 m Sx Sy Ix Iy 1
spacing s = 0.65 m mm^3 mm^3 mm^4 mm^4 2
span of purlin L = 3.50 m 18800 5900 1051000 194000 wt
mean ht of roof = 16.25 m Xc = 17.0 mm
wind zone = II F2.3.A m= 4.76 kg/m
exposure category = B S2.3.2 w, N/m Case 1 Case 2 Case 3
importance factor I = 1.00 T2.2D wn = 634.4 629.4 -276.2 3
Fy = 250 MPa wt = 57.7 43.3 16.8 4
Deadload: R2 = 126.2 94.6 36.7
roofing = 100 Pa
purlins + acc. = 80 Pa Case 1 Case 2 Case 3
others = 200 Pa A B A B A B
total deadload = 380 Pa Mn 592 971 587 964 -258 -423
liveload = 600 Pa T2.1C 1 -31.49 -51.67 -31.24 -51.26 13.71 22.50
Windload : Normal Force Method 2 -31.49 -51.67 -31.24 -51.26 13.71 22.50
stagnation pressure qs = 1500 Pa F2.3-A 3 31.49 51.67 31.24 51.26 -13.71 -22.50
exposure coefficient Ce = 0.70 T2-J 4 31.49 51.67 31.24 51.26 -13.71 -22.50
shape coefficient Cq = -0.90 0.30 T2-K Mt 12.36 22.08 9.27 16.56 3.60 6.42
design unit presssure: Pw = CeCqQsI [2-13] 1 -2.10 3.74 -1.57 2.81 -0.61 1.09
suction = -945.0 Pa 2 1.08 -1.93 0.81 -1.45 0.32 -0.56
pressure = 315.0 Pa 3 -2.10 3.74 -1.57 2.81 -0.61 1.09
Normal loads per linear meter: 4 1.08 -1.93 0.81 -1.45 0.32 -0.56
DL = 245.99 N/m F1 -33.58 -47.93 -32.81 -48.45 13.10 23.58
LL = 388.40 N/m F2 -30.40 -53.60 -30.42 -52.71 14.02 21.93
WL = -614.25 N/m F3 29.39 55.41 29.67 54.07 -14.32 -21.41
= 204.75 N/m F4 32.57 49.74 32.05 49.81 -13.39 -23.06
Tangential loads per linear meter: Fmax = 55.41 MPa OK
DL = 22.36 N/m allow y = 19.44 mm
LL = 35.31 N/m actual y = 5.90 mm OK
WL = 0.00 N/m actual wt = 71.8 Pa OK
Design of Sag Rods :
length of top chord = 5.52 m allow Fa = 150 MPa
no. of sag rods spans = 8 spans reqd d = 3.02 mm
sum R2 = 1072 N Use d = 10 mm
Structure: 0 Developed by: Engr. Ramon Gitamondoc
Owner: 0 Licensed to: Engr. Thomas John Agrabio
Address: 0 Company:

Material Specifications: NSCP 2001

Steel db, mm fy, MPa No. of Levels = 1
bar dia <= 10 233 Top level of range = 1
bar dia >= 12 276 Ca = 0.44
Concrete Level fc', MPa I= 1.00
Level <= 10 21 ρ= 1.20
Level > 10 21 f1 = 0.50

Mark: C1 Level 2 to 1
Girders North South West East Upper column: Seismic: Peq Veq Meq
offset = Lc = x-dir 6.00 5.00 10.00
Vdl = P'dl = 12.00 y-dir 6.00 5.00 10.00
Vll = P'll = 6.60
Mdl = ex' = Restraint x-dir y-dir
Mll = ey' = Factor = 1 1

Column Data: Load Case LC1 LC2 LC3 LC4 LC5 LC6
fc' = 21 MPa Pu = 19.10 13.49 20.23 20.23 18.41 18.41
fy, main = 276 MPa Mx = 0.00 0.00 0.00 13.20 0.00 13.20
fy, ties = 233 MPa My = 0.00 0.00 13.20 0.00 13.20 0.00
yc = 23.6 kN/m3 Pnx = 1466 1466 1466 42 1466 37
Lc = 3.00 m Pny = 1466 1466 42 1466 37 1466
b = 300 mm Pn = 1218 1218 42 42 37 37
h = 300 mm 0Pn = 853 853 NA NA NA NA
n1 = 3 pcs SR = 0.02 0.02 0.52 0.52 0.54 0.54
n2 = 3 pcs Rem OK OK OK OK OK OK
n3 = 1 pcs Ties = 10d (1 loop) 1@50, 6@75, rest @ 72 mm o.c. to M.H.
db = 12 mm Liveload reduction:
pc = 40 mm L= 4.00 m cy = 300 OK
tie db = 10 mm W= 4.00 m cx = 300 OK
lat ties = 1 loop R= 1.00 >= 0.8 pg = 0.0101 OK
plaster = 0 mm Lowermost column? YES

Footing: FC1 Case LC1 LC2 LC3 LC4 LC5 LC6

Type: 1 P 19.56 16.26 23.85 23.85 20.55 20.55
fc' = 21 MPa Mx 0.00 0.00 0.00 -7.14 0.00 -7.14
qe = 100 kPa My 0.00 0.00 -7.14 0.00 -7.14 0.00
a= 0.30 m qmax 21.74 15.87 98.21 98.21 93.81 93.81
b= 0.30 m CR 0.22 0.16 0.98 0.98 0.94 0.94
yc = 23.6 kN/m3 Rem OK OK OK OK OK OK
ys = 18.00 kN/m3 Force Capacity SR Rem
qa = 100 kPa Shear kN kN < 1.0
H= 0.75 m Vx 13 61 0.22 OK
B= 0.75 m Vy 13 61 0.22 OK
L= 0.75 m Vp 20 138 0.15 OK
T= 0.20 m Reqd n Spacing Adopt n Bar dia.
d' = 75 mm Flexure Loc pcs mm pcs mm Rem
cm = 1.00 BOT x-dir 2.7 106 6 12 OK
n= 1 layers y-dir 2.7 106 6 12 OK
On piles? NO TOP x-dir NA NA 6 20 OK
y-dir NA NA 6 20 OK
Footing Schedule:
Rebars
Mark B x L x T (m) LOC Remark (NO PEDESTAL)
// to x-axis // to y-axis
TOP NA NA /Bars no end hook
FC1 0.75 x 0.75 x 0.20
BOT 6 pcs - 12d 6 pcs - 12d /Bars no end hook
MACHINE ROOM.sdb 25/05/2020

0.26
1.04
0.564
0.168
0.235
0.322
0.378

0.549
0.153
0.387

0.099
0.5

0.06
0.395 0.5

0.011
0.3

0.044
0.666 41

0.119
0.0 0.2 75 33

0.15
1.04

0.613
0.26 0 .1 52 31
0.41 0.31 09
3 3
0.174 0.186 0.292 0.319 0.302 0.247 0.179 0.105

0.00 0.50 0.70 0.90 1.00

SAP2000 21.0.2 Steel P-M Interaction Ratios (AISC-ASD89) KN, m, C