LTY400HM02 Samsung PDF

Global LCD Panel Exchange Center www.panelook.
com
Contents
Revision History -------------------------------------------------------------------------------------------- (3)

General Description --------------------------------------------------------------------------------------- (4)
General Information --------------------------------------------------------------------------------------- (4)
1. Absolute Maximum Ratings -------------------------------------------------------------------------- (5)
2. Optical Characteristics --------------------------------------------------------------------------------- (6)
3. Electrical Characteristics ------------------------------------------------------------------------------- (9)
3.1 TFT LCD Module
3.2 Back Light Unit
4. Block Diagram ------------------------------------------------------------------------------------------- (11)
5. Input Terminal Pin Assignment --------------------------------------------------------------------- (12)
5.1 Input Signal & Power
5.2 Inverter Input Pin Configuration
5.3 LVDS Interface
5.4 Input Signals, Basic Display Colors and Gray Scale of Each Color
6. EDID Information --------------------------------------------------------------------------------------- (18)
6.1 EEPROM Data
6.2 EEPROM Data Map
7. Interface Timing ---------------------------------------------------------------------------------------- (20)
7.1 Timing Parameters (DE only mode)
7.2 Timing Diagrams of interface Signal (DE only mode)
7.3 Power ON/OFF Sequence
8. Outline Dimension -------------------------------------------------------------------------------------- (23)
9. EMI Specification --------------------------------------------------------------------------------------- (25)
10. UL Approval
11. Reliability Test ----------------------------------------------------------------------------------------- (26)
12. Packing ------------------------------------------------------------------------------------------------ (27)
13. Marking & Others ------------------------------------------------------------------------------------- (28)
14. General Precaution ---------------------------------------------------------------------------------- (29)
14.1 Handling
14.2 Storage
14.3 Operation
14.4 Operation Condition Guide
14.5 Others
MODEL LTY[Z]400HM02 Doc. No 05-001-S-100426 Page 2 / 31
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
* Revision History
Rev.
Date Page Summary
No
Jan.
29, 000 - First Issued
2010
•LED Vendor Multiplication

- SLED ˧ SLED + SSC(2nd Vendor)
Apr. Luminance Min Typ

26, 001 4,6
SLED 380 450
2010
SSC 330 400
Model Code Added : LTY[Z]4000HM02-103
General Description
Description
LTY[Z]400HM02 is a color active matrix liquid crystal display (LCD) that uses amorphous
silicon TFT(Thin Film Transistor) as switching components. This model is composed of a
TFT LCD panel, a driver circuit and a back light unit. The resolution of a 40.0“ is 1920 x
1080 and this model can display up to 16.7million colors with wide viewing angle of 89¶ or
higher in all directions. This panel is intended to support applications to provide a excellent
performance for Flat Panel Display such as Home-alone Multimedia TFT-LCD TV, Display
terminals for AV application products, and High Definition TV (HDTV).
Features
RoHS compliance (Pb-free)
High contrast ratio, high aperture ratio, fast response time
SPVA (Super Patterned Vertical Align) mode
Wide viewing angle (·89¶)
Full HD (1920 x 1080 pixels) resolution (16:9)
Low Power consumption
WLED (White Light Emitting Diode) Backlight
LVDS (Low Voltage Differential Signaling) interface
General Information
Items Specification Unit Note

927.7(HTYP) x 545.8(VTYP) ·1.0mm
Module Size mm
25.3(DMAX)
Weight 8000(Max) g
Pixel Pitch 0.15375(H) * 3 x 0.46125(V) mm
Active Display Area 885.6(H) x 498.15(V) mm
Surface Treatment Haze 7%, Hard-coating (3H)
Display Colors 8 bit- 16.7M colors
Number of Pixels 1920 x 1080 pixel
Pixel Arrangement RGB vertical stripe
Display Mode Normally Black

Luminance of White 450 / *400 cd/m2 Typ.
Note. “*” Marked Item is Luminance of 2nd LED Vendor.
1. Absolute Maximum Ratings

If the condition exceeds maximum ratings, it can cause malfunction or unrecoverable
damage to the device.
Item Symbol Min. Max. Unit Note

Power Supply Voltage VDD GND-0.5 13 V (1)
Storage temperature TSTG -20 65 ୅ (2)

Operating Temperature TOPR 0 50 ୅ (2)
Panel surface temperature TSUR 0 65 ୅ (3)
Shock ( non - operating ) SNOP - 50 G (4)
Vibration ( non - operating ) VNOP - 1.5 G (5)
Note (1) Ta= 25 · 2 ¶C
(2) Temperature and relative humidity range are shown in the figure below.
a. 93.8 % RH Max. (Ta ˺ 40 ¶C)
b. Maximum wet-bulb temperature at 40 ¶C or less. (Ta ˺ 40 ¶C)
c. No condensation
(3) Polarizer will not be damaged in this range, even though abnormal visual problems occur
in TSUR range.
(4) 11ms, sine wave, one time for ·X, ·Y, ·Z axis
(5) 10-300 Hz, Sweep rate 10min, 30min for X,Y,Z axis
(40, 93.8)
(50, 50.4)
(65, 27.7)
Fig. Temperature and Relative humidity range
2. Optical Characteristics
The optical characteristics should be measured in a dark room or equivalent.

Measuring equipment : TOPCON BM-7,SPECTRORADIOMETER SR-3
(Ta = 25 · 2¶C, VDD=12V, fv= 60Hz, fDCLK=148.5MHz, Dim = 100%)
Item Symbol Condition Min. Typ. Max. Unit Note
Contrast Ratio (3)
C/R *2500 5000 -
(Center of screen) SR-3
Rising Tr - 12 70
Response Falling Tf - 8 18 (5)
msec
Time BM-7
G-to-G
Tg - 8 -
[AVE]
Luminance of White Normal 380 450 (6)
YL - cd/m2
(Center of screen) TL,R=0 **330 **400 SR-3
TU,D=0
Rx 0.625
Red
Ry Viewing 0.340
Angle
Gx 0.315
Green
Color Gy 0.628
TYP. TYP. (7),(8)
Chromaticity
Bx -0.03 0.155 +0.03 SR-3
(CIE 1931)
Blue
By 0.045
Wx 0.280
White
Wy 0.290
(7)
Color Gamut - - 72 - %
SR-3
Color Temperature - - 10000 - K (7)
Gamma Ƚ - 2.2 - SR-3
TL 79 89 -
Hor.
Viewing TR 79 89 - (8)
C/R˻10 Degree
Angle TU 79 89 - SR-3
Ver.
TD 79 89 -
Brightness Uniformity (4)
Buni - - 30 %
(9 Points) SR-3
* marked Items Value does not Specification above when “White stain” occurs at Center Point [Point ྜྷ of Note 2.]
**marked Items are the value of 2nd Vendor LED.
Note (1) Test Equipment Setup
The measurement should be executed in a stable, windless and dark room between
40min and 60min after lighting the back light at the given temperature for stabilization
of the back light. This should be measured in the center of screen.
Single lamp current @ Vdim = 100%

Environment condition : Ta = 25 · 2 ¶C
Photo detector
Photo detector Field
SR-3 1ദ
BM-7 2ദ Field
SR-3 : 50໅
BM-7 : 50໅
TFT - LCD Module

LCD Panel
The center of the screen
Note (2) Definition of test point
320 960 1600
Active Area
180 ྡ ྠ ྟ
Test Point
540 ྞ ྜྷ ྜ
900 ྛ ྚ ྙ
Note (3) Definition of Contrast Ratio (C/R)

: Ratio of gray max (Gmax) & gray min (Gmin) at the center point 㽶 of the panel
G max
C/R
G min
Gmax : Luminance with all pixels white
Gmin : Luminance with all pixels black
Note (4) Definition of 9 points brightness uniformity
( B max B min)
Buni 100
B max
Bmax : Maximum brightness
Bmin : Minimum brightness
Note (5) Definition of Response time : Sum of Tr, Tf
Display data Black (data off) White (data on) White (data off)
TR TF
Optical Instruments
100%
Response
90%
10%
0%
TIME
Note (6) Definition of Luminance of White : Luminance of white at center point 㽶
Note (7) Definition of Color Chromaticity (CIE 1931)

Color coordinate of Red, Green, Blue & White at center point 㽶
Note (8) Definition of Viewing Angle

: Viewing angle range (C/R ı10)
3. Electrical Characteristics
3.1 TFT LCD Module

The connector for display data & timing signal should be connected.
Ta = 25¶C · 2 ¶C
Item Symbol Min. Typ. Max. Unit Note
Voltage of Power Supply VDD 11 12 13 V (1)
(a) Black - 580 -
Current (b) White - 850 1020
of Power IDD mA (2),(3)
Supply (c) Mosaic - 700 -
(4) Max Pattern - 930 1120
Vsync Frequency fV 47 60 62 Hz
Hsync Frequency fH 50 67.5 73 kHz
Main Frequency fDCLK 130 148.5 155 MHz
Rush Current IRUSH - - 5 A (4)
Note (1) The ripple voltage should be controlled under 10% of VDD.
(2) fV=60Hz, fDCLK = 148.5MHz, VDD = 12.0V, DC Current.
(3) Power dissipation check pattern (LCD Module only)
a) Black Pattern b) White Pattern c) Mosaic d)Max. Pattern
(4) Measurement Conditions
VDD
100%
90%
10%
GND
TRUSH=1ms
Rush Current IRUSH can be measured when TRUSH. is1ms
3.2 Back Light Unit
The back light unit contains 176 LEDs.

The characteristics of lamps are shown in the following tables.
Ta=25 · 2¶C
Item Symbol Min. Typ. Max. Unit Note

Operating Life Time Hr 30,000 - - Hour (1)
Continuous Iop - - 160 mA /String

Operating
Current Impulsive @110mA
Iop - - 190 mA
(60Hz/Duty50%) /Duty100%
44LEDs
Continuous Vop - - 155 V
Operating /110mA@Tj 25୅
Voltage Impulsive
Vop - - 168 V Tj 25୅
(60Hz/Duty50%)
Note (1) It is defined as the time to take until the brightness reduces to 50% of its original value.
[Definition of Operating Voltage : At each Strings, Iop = 110.0 mArms (typ.)]
4. Block Diagram
5. Input Terminal Pin Assignment

5.1. Input Signal & Power Connector : IS050-C51B-C38(UJU)
Compatible with FI-RE51S-HF(JAE)
PIN PIN
Signal Description Signal Description
No. No.
1 Power VDD 26 RX1_AP_I Even LVDS Signal +
2 Power VDD 27 RX1_BN_I Even LVDS Signal -
3 Power VDD 28 RX1_BP_I Even LVDS Signal +

4 Power VDD 29 RX1_CN_I Even LVDS Signal -
5 Power VDD 30 RX1_CP_I Even LVDS Signal +

6 N.C. No Connection 31 GND GND
7 GND GND 32 RX1_CLKN_I Even LVDS Clock-
8 GND GND 33 RX1_CNKP_I Even LVDS Clock+
9 GND GND 34 GND GND
10 RX0_AN_I Odd LVDS Signal - 35 RX1_DN_I Even LVDS Signal -
11 RX0_AP_I Odd LVDS Signal + 36 RX1_DP_I Even LVDS Signal +
12 RX0_BN_I Odd LVDS Signal - 37 N.C. No Connection
13 RX0_BP_I Odd LVDS Signal + 38 N.C. No Connection
14 RX0_CN_I Odd LVDS Signal - 39 GND GND
15 RX0_CP_I Odd LVDS Signal + 40 SCL_C I2C SCL
16 GND GND 41 SDA_C I2C SDA
17 RX0_CLKN_I Odd LVDS CLK - 42 VSYNC V Sync Signal
18 RX0_CLKP_I Odd LVDS CLK + 43 BUS_SW Bus Switching
19 GND GND 44 N.C. No Connection
20 RX0_DN_I Odd LVDS Signal - 45 N.C. No Connection
21 RX0_DP_I Odd LVDS Signal + 46 LUT SEL0 DCC LUT Select 0
22 N.C. No Connection 47 LUT SEL1 DCC LUT Select1
23 N.C. No Connection 48 LUT SEL2 DCC LUT Select2
24 GND GND 49 HSYNC H Sync Signal
25 RX1_AN_I Even LVDS Signal - 50 TCON_RDY T-Con Ready
51 SEL1 SEC Internal Use Only
̰ BUS_SW : I2C BUS Switching
Operation Description
sv~Vvwlu SDA/SCL LINE BECOME HI-Z
HIGH USER CAN ACCESS EEPROM
̰ DCC Look Up Table Selection

Description ( Based on DCC On)
Pin N.O. 48 47 46
LUT %(For Interpolate)
0 0 0 For 60Hz 100%
0 0 1 For 60Hz 100%X1.25
0 1 0 For 60Hz @ Low Temp. 100%X1.25
Select 0 1 1 For 60Hz @ Low Temp. (100%X1.25) X 1.25

bit 1 0 0 For 50Hz 100%
1 0 1 For 50Hz 100%X1.25
1 1 0
0%
1 1 1
̰ TCON Ready
Operation Description
Low Æ High Normal Operation
High Æ Low Error Operation
Note(1) Pin number starts from Right side
PCB
̷
Pin No. 1 Pin No. 51
#1 #51
connect name
#1 #51
Fig. Connector diagram
a. All GND pins should be connected together and also be connected to the LCD’s
metal chassis.
b. All power input pins should be connected together.
c. All NC pins should be separated from other signal or power.
5.2 Inverter Input Pin Configuration

̰ 4pin :DC Voltage Connecter : 51103-0400 (Molex)
Pin No. Pin Configuration (FUNCTION)

1 1 Channel DC Voltage
2 2 Channel DC Voltage
3 No Connection
4 No Connection
̰ 5pin :Feedback Voltage Connecter : 51103-0500 (Molex)
Pin No. Pin Configuration (FUNCTION)

1 1 Channel Feedback
2 2 Channel Feedback
3 No Connection
4 No Connection
5 No Connection
5.3 LVDS Interface
LVDS pin Odd Data Even Data

TxIN/RxOUT0 R2 R2
TxIN/RxOUT1 R3 R3
TxIN/RxOUT2 R4 R4
TxOUT/RxIN0 TxIN/RxOUT3 R5 R5
TxIN/RxOUT4 R6 R6
TxIN/RxOUT6 R7 R7
TxIN/RxOUT7 G2 G2
TxIN/RxOUT8 G3 G3
TxIN/RxOUT9 G4 G4
TxIN/RxOUT12 G5 G5
TxOUT/RxIN1 TxIN/RxOUT13 G6 G6
TxIN/RxOUT14 G7 G7
TxIN/RxOUT15 B2 B2
TxIN/RxOUT18 B3 B3
TxIN/RxOUT19 B4 B4
TxIN/RxOUT20 B5 B5
TxIN/RxOUT21 B6 B6
TxOUT/RxIN2 TxIN/RxOUT22 B7 B7
TxIN/RxOUT24 HSYNC HSYNC
TxIN/RxOUT25 VSYNC VSYNC
TxIN/RxOUT26 DEN DEN
TxIN/RxOUT28 R0 R0
TxIN/RxOUT29 R1 R1
TxIN/RxOUT30 G0 G0
TxOUT/RxIN3 TxIN/RxOUT31 G1 G1
TxIN/RxOUT32 B0 B0
TxIN/RxOUT33 B1 B1
TxIN/RxOUT34 Reserved Reserved
5.4 Input Signals, Basic Display Colors and Gray Scale of Each Color
DATA SIGNAL
GRAY
DISPLAY
COLOR RED GREEN BLUE SCALE
(8bit)
LEVEL
R0 R1 R2 R3 R4 R5 R6 R7 G0 G1 G2 G3 G4 G5 G6 G7 B0 B1 B2 B3 B4 B5 B6 B7
BLACK 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 -
BLUE 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 -
GREEN 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 -
BASIC CYAN 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -
COLOR
RED 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 -
MAGENTA 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 -
YELLOW 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 -
WHITE 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -
BLACK 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R0
1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R1
DARK 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R2
GRAY ˦
: : : : : : : : : : : : : : : : : : R3~
SCALE
OF : : : : : : : : : : : : : : : : : : R252
RED ˨
LIGHT 1 0 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R253
0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R254
RED 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R255
BLACK 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 G0
0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 G1
DARK 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 G2
GRAY ˦
SCALE : : : : : : : : : : : : : : : : : : G3~
OF : : : : : : : : : : : : : : : : : : G252
GREEN ˨
LIGHT 0 0 0 0 0 0 0 0 1 0 1 1 1 1 1 1 0 0 0 0 0 0 0 0 G253
0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 G254
GREEN 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 G255
BLACK 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 B0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 B1
DARK 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 B2
GRAY ˦
: : : : : : : : : : : : : : : : : : B3~
SCALE
OF : : : : : : : : : : : : : : : : : : B252
BLUE ˨
LIGHT 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 1 1 1 1 1 B253
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 B254
BLUE 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 B255
Note) Definition of Gray :

Rn : Red Gray, Gn : Green Gray, Bn : Blue Gray (n = Gray level)
Input Signal : 0 = Low level voltage, 1 = High level voltage
6. EDID Information
6.1 EEPROM Data
EEPROM Data
No Item Spec Address Data Remark
Panel Product SONY Choice

1 XXXX 00 XX
Vender - Note 1
2 Screen Size XX 01 XX 16讝
3 H-Resolution XXXX 02,03 XX,XX 16讝
4 V-Resolution XXX 04,05 XX,XX 16讝
Vertical
5 XX 06 XX - Note 2
Frequency
6 Data Format XX 07 XX - Note 3
FRC Revision ASCII
7 X ED XX
Information - Note 4
XX,XX,XX,XX,XX,
XX,
XXX(X)XXXXX ASCII
8 Part Number E0~EC XX,XX,XX,XX,XX,
XX - Note 5, 6
XX
,XX,XX,XX,XX
୔ Note 1. ୔ Note 2. ୔ Note 3.

Data Panel Vender Code Data V-Frequency Data Data Format
00 HDLCD(SEC) 00 50/60Hz 00 6Bit
01 Others 01 100/120HZ 01 8Bit
02 Others 02 200/240Hz 02 10Bit
03 Others
04 Others
05 Others
୔ Note 4.
- FRC Revision Code will be Changed from “00” to “41” (A)
When FRC IC is changed. At First MP. This Code will be “00”
୔ Note 5.
- LTY[Z]XXXXXXX Only for SEC Model
୔ Note 6.
- Rest of them must be “00” (Null)
6.2 EEPROM Data Map

0 1 2 3 4 5 6 7 8 9 A B C D E F
0 XX XX XX XX XX XX XX XX 00 00 00 00 00 00 00 00
1 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
2 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
3 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
4 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
5 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
6 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
7 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
8 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
9 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
A 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
B 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
C 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
D 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
E XX XX XX XX XX XX XX XX XX XX XX XX XX XX 00 00
F 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
7. Interface Timing
7.1 Timing Parameters ( DE only mode )
SIGNAL ITEM SYMBOL MIN. TYP. MAX. Unit NOTE
Clock 1/TC 130 148.5 155 MHz -
Hsync Frequency FH 50 67.5 73 KHz -

Vsync FV 47 60 62 Hz -
Active
Display TVD - 1080 - lines -
Vertical Period
Display Term
Vertical
TVB 1100 1125 1480 Lines -
Total
Active
Display THD - 1920 - clocks -
Horizontal Period
Display Term
Horizontal
TH 2154 2200 2450 clocks -
Total
Note) This product is DE only mode. The input of Hsync & Vsync signal does
not have an effect on normal operation.
(1) Test Point : TTL control signal and CLK at LVDS Tx input terminal in system
(2) Internal VDD = 3.3V
7.2 Timing diagrams of interface signal ( DE only mode )
TV
TVD TVB
DE
TH
THD
DE
DCLK
TC
DATA
SIGNALS
TC
TCH TCL
DCLK 0.5
VCC
TDS TDH
DISPLAY 0.5
DATA
VCC
TES
DE 0.5
VCC
7.3 Power ON/OFF Sequence
To prevent a latch-up or DC operation of the LCD Module, the power on/off

sequence should be as the diagram below.
[UNIT : mS]
Min Max Min Max

T1 0.47 30 T8 30 -
T2 0 100 T9 500 -
T3 0 100 T10 50 -
T4 0.1 50 T11 100 -
T5 220 350 T12 0 50

T6 0 30 T13 0 300
T7 0 30 T14 1000 -
The supply voltage of the external system for the Module input should be the same
as the definition of VDD.
Apply the lamp voltage within the LCD operation range. When the back light turns on
before the LCD operation or the LCD turns off before the back light turns off,
the display may momentarily show abnormal screen.
In case of VDD = off level,
please keep the level of input signals low or keep a high impedance.
T14 should be measured after the Module has been fully discharged between power off
and on period.
Interface signal should not be kept at high impedance when the power is on.
8. Outline dimension (Front view)
Outline dimension (Rear View)
9. EMI Specification
: -3dB at CISPR22 Class B
This EMI Recommendation is recommended to be measured as SET Condition.
10. UL Approval
11. Reliability Test

Item Test condition Quantity
Temperature
0 ௥ 50ఁ,10Cycle determination 4EA
Step Stress
HTOL 50ఁ, 1000hr (500hr determination) 8EA

LTOL 0ఁ, 1000hr (500hr determination) 4EA
RTOL 20 ఁ, continue ~ 4EA
HTS 70ఁ, 1000hr (500hr determination) 4EA
LTS -30ఁ,1000hr (500hr determination) 4EA
THB 40ఁ / 95%RH,1000hr (500hr determination) 4EA
WHTS 60ఁ / 75%RH, 1000hr (500hr determination) 4EA
T/C -20 ఁ ~ 60 ఁ, 200cycle (100cycle determination) 4EA
ESD
ᇹ10 kV,200Ꮔ/100 ᇢ,9Point,3times/Point 3EA
(non-operation)
contact : ᇹ8 kV ,150Ꮔ/330ᇢ,210Point,1 time/Point

ESD(operation) 3EA
non-contact : ᇹ15 kV,150Ꮔ/330ᇢ,100Point,1 time/Point
Input Con. ESD contact : ᇹ2kV,200Ꮔ/100,Input Con.Pin,3 times/Pin 3EA
POWER
30sec (on) / 30sec(off) : 12,000 times 4EA
ON/OFF
Vibration 10~300Hz/1.5G/10minSR, XYZ, 30min/axis 3EA

Shock Condition : 11msec, ᇹXYZ 1time/axis 50G 3EA
PALLET
1.05 Grms, 2~200Hz, Random, Z axis 1Hr 1PALLET(15EA)
Vibration
PALLET Drop 20cm, Bottom, Front, Rear 1times 1PALLET(15EA)
[ Result Evaluation Criteria]

Under the display quality test conditions with normal operation state, these shall
be no change which may affect practical display function.
HTOL/ LTOL : High/Low Temperature Operating Life,

THB : Temperature Humidity Bias
HTS/LTS : High/Low Temperature Storage
WHTS : Wet High Temperature Storage
12. PACKING
12.1 CARTON (Internal Package)

(1) Packing Form
Corrugated fiberboard box and corrugated cardboard as shock absorber
(2) Packing Method
Packing Pallet Box
Module (15EA)
Cushion Set
Direction be able to Open
Pallet
12.2 Packing Specification
Item Specification Remark
1. 120Kg/LCD(15ea)
2. 7kg/Cushion Set(2ea)
LCD Packing 15 ea / (Packing-
3. 6.7kg/Packing-Pallet Box(1ea)
Pallet Box)
4. Cushion Material : EPS
5. Packing Pallet Box Material : SW
Desiccant (Drier) 2ea/LCD 10g/ea, Cobalt-dichloride-free
Pallet 1 Box / Pallet Pallet weight : 8kg
Packing Direction Vertical -
Total Pallet Size H x V x height 1150mm x 985mm x 815mm
Pallet(8kg) + Module( 15 x 8 = 120kg) +

Total Pallet Weight 142kg Cushion(7kg) + Pallet-BOX(6.7kg) +
Desiccant(0.02kg x 15 = 0.3kg)
13. MARKING & OTHERS
A nameplate bearing followed by is affixed to a shipped product at the specified

location on each product.
(1) Parts number : LTY[Z]400HM02-XXX
(2) Revision: One letters
(3) Lot number : X X X X XXX XX X
Cell Position No. (In the Glass)

Glass No. (In the one Lot)
Lot No. (Glass)
Month
Year (Note1)
Product code
(4) Nameplate Indication Line
Week code : 05 29
LTY[Z]400HM02
week
year
40mm
[[[[[[ [[[[[[[[[[#########{{{
Revision code
Lot number
LTY[Z]400HM02XXX
80mm
(5) Packing box attach
100mm
LTY[Z]400HM02-XXX Part number
XXXX Revision code

15
Box serial number
0703
14. General Precautions

14.1 Handling
(a) When the Module is assembled, it should be attached to the system firmly
using all mounting holes. Be careful not to twist and bend the Module.
(b) Because the inverter use high voltage, it should be disconnected from power
before it is assembled or disassembled.
(c) Refrain from strong mechanical shock and / or any force to the Module.
In addition to damage, this may cause improper operation or damage to the Module
and LED back light.
(d) Note that polarizers are very fragile and could be damage easily.
Do not press or scratch the surface harder than a HB pencil lead.
(e) Wipe off water droplets or oil immediately. If you leave the droplets for a long
time, staining or discoloration may occur.
(f) If the surface of the polarizer is dirty, clean it using absorbent cotton or soft cloth.
(g) Desirable cleaners are water, IPA(Isopropyl Alcohol) or Hexane.

Do not use Ketone type materials(ex. Acetone), Ethyl alcohol, Toluene, Ethyl acid
or Methyl chloride. It might permanent damage to the polarizer due to chemical
reaction.
(h) If the liquid crystal material leaks from the panel, it should be kept away
from the eyes or mouth . In case of contact with hands, legs or clothes, it must
be washed away with soap thoroughly.
(i) Protect the Module from static, or the CMOS Gate Array IC would be damaged.
(j) Use finger-stalls with soft gloves in order to keep display clean during the
incoming inspection and assembly process.
(k) Do not disassemble the Module.
(l) Do not pull or fold the LED FFC.
(m) Do not adjust the variable resistor located on the Module.
(n) Protection film for polarizer on the Module should be slowly peeled off just before use
so that the electrostatic charge can be minimized.
(o) Pins of I/F connector should not be touched directly with bare hands.
14.2 Storage
(a) Do not leave the Module in high temperature, and high humidity for a long time.
It is highly recommended to store the Module with temperature from 0 to 35୅
and relative humidity of less than 70%.
(b) Do not store the TFT-LCD Module in direct sunlight.
(c) The Module should be stored in a dark place. It is prohibited to apply sunlight or
fluorescent light in storing.
14.3 Operation
(a) No Connection or disconnect the Module in the "Power On" condition.
(b) Power supply should always be turned on/off by the "Power on/off sequence"
(c) Module has high frequency circuits. Sufficient suppression to the electromagnetic
interference should be done by system manufacturers. Grounding and shielding methods
may be important to minimize the interference.
(d) The cable between the back light connector and its inverter power supply should
be connected directly with a minimized length. A longer cable between
the back light and the inverter may cause lower luminance of LED and
may require higher startup voltage(Vs).
14.4 Operation Condition Guide
(a) The LCD product should be operated under normal conditions.

Normal condition is defined as below;
- Temperature : 20·15୅
- Humidity : 55·20%
- Display pattern : continually changing pattern (Not stationary)
(b) If the product will be used in extreme conditions such as high temperature,
humidity, display patterns or operation time etc.., It is strongly recommended
to contact SEC for Application engineering advice. Otherwise, its reliability and
function may not be guaranteed. Extreme conditions are commonly found at
Airports, Transit Stations, Banks, Stock market, and Controlling systems.
14.5 Others
(a) Ultra-violet ray filter is necessary for outdoor operation.
(b) Avoid condensation of water. It may result in improper operation or disconnection

of electrode.
(c) Do not exceed the absolute maximum rating value. (supply voltage variation,
input voltage variation, variation in part contents and environmental temperature,
and so on)
Otherwise the Module may be damaged.
(d) If the Module keeps displaying the same pattern for a long period of time,
the image may be "sticked" to the screen.
To avoid image sticking, it is recommended to use a screen saver.
(e) This Module has its circuitry PCB's on the rear side and should be handled
carefully in order not to be stressed.
(f) Please contact SEC in advance when you display the same pattern for a long time.

LTY400HM02 Samsung PDF

Uploaded by

Copyright:

Available Formats

LTY400HM02 Samsung PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

LTY400HM02 Samsung PDF

Uploaded by

Copyright:

Available Formats

Global LCD Panel Exchange Center www.panelook.

Revision History -------------------------------------------------------------------------------------------- (3)

MODEL LTY[Z]400HM02 Doc. No 05-001-S-100426 Page 2 / 31

•LED Vendor Multiplication

Apr. Luminance Min Typ

Model Code Added : LTY[Z]4000HM02-103

MODEL LTY[Z]400HM02 Doc. No 05-001-S-100426 Page 3 / 31

Items Specification Unit Note

Display Colors 8 bit- 16.7M colors

Number of Pixels 1920 x 1080 pixel

Pixel Arrangement RGB vertical stripe

Display Mode Normally Black

Note. “*” Marked Item is Luminance of 2nd LED Vendor.

MODEL LTY[Z]400HM02 Doc. No 05-001-S-100426 Page 4 / 31

1. Absolute Maximum Ratings

Item Symbol Min. Max. Unit Note

Storage temperature TSTG -20 65 ୅ (2)

Fig. Temperature and Relative humidity range

MODEL LTY[Z]400HM02 Doc. No 05-001-S-100426 Page 5 / 31

The optical characteristics should be measured in a dark room or equivalent.

Single lamp current @ Vdim = 100%

MODEL LTY[Z]400HM02 Doc. No 05-001-S-100426 Page 6 / 31

TFT - LCD Module

The center of the screen

Note (2) Definition of test point

320 960 1600

Note (3) Definition of Contrast Ratio (C/R)

MODEL LTY[Z]400HM02 Doc. No 05-001-S-100426 Page 7 / 31

Note (4) Definition of 9 points brightness uniformity

Note (5) Definition of Response time : Sum of Tr, Tf

Note (6) Definition of Luminance of White : Luminance of white at center point 㽶

Note (7) Definition of Color Chromaticity (CIE 1931)

Note (8) Definition of Viewing Angle

MODEL LTY[Z]400HM02 Doc. No 05-001-S-100426 Page 8 / 31

3.1 TFT LCD Module

(4) Measurement Conditions

MODEL LTY[Z]400HM02 Doc. No 05-001-S-100426 Page 9 / 31

3.2 Back Light Unit

The back light unit contains 176 LEDs.

Item Symbol Min. Typ. Max. Unit Note

Continuous Iop - - 160 mA /String

MODEL LTY[Z]400HM02 Doc. No 05-001-S-100426 Page 10 / 31

MODEL LTY[Z]400HM02 Doc. No 05-001-S-100426 Page 11 / 31

5. Input Terminal Pin Assignment

2 Power VDD 27 RX1_BN_I Even LVDS Signal -

3 Power VDD 28 RX1_BP_I Even LVDS Signal +

5 Power VDD 30 RX1_CP_I Even LVDS Signal +

25 RX1_AN_I Even LVDS Signal - 50 TCON_RDY T-Con Ready

51 SEL1 SEC Internal Use Only

MODEL LTY[Z]400HM02 Doc. No 05-001-S-100426 Page 12 / 31

̰ BUS_SW : I2C BUS Switching

̰ DCC Look Up Table Selection

0 1 0 For 60Hz @ Low Temp. 100%X1.25

Select 0 1 1 For 60Hz @ Low Temp. (100%X1.25) X 1.25

1 0 1 For 50Hz 100%X1.25

MODEL LTY[Z]400HM02 Doc. No 05-001-S-100426 Page 13 / 31

Note(1) Pin number starts from Right side

Pin No. 1 Pin No. 51

Fig. Connector diagram