VT600X USER MANUAL

GPS
Vehicle
Tracker

User Manual

V5.4

VT600X

1
 VT600X USER MANUAL

Preface

Thank you for purchasing our products. This deliberately edited manual is

to introduce the tracker with the complete technical data and the instructions

showing how to operate the device smoothly and correctly. Make sure to read

this manual carefully before using this product. Most problems could be solved

through the explanations and the troubleshooting tips. Once you finish reading

it, keep it handy for necessary reference. Please note that specification and

information are subject to changes without prior notice in this manual. Any

change will be integrated in the latest release. The manufacturer assumes no

responsibility for any errors or omissions in this document.

Content
Ⅰ. Preface…………………………………………... 2
Ⅱ. Attentions……………………………………….. 3
Ⅲ Hardware description…..…………………….… 3
Ⅳ. Main function……………………………….….. 3
Ⅴ. Set up………………………………………...….. 4
Ⅵ. Installation diagram………………………...….. 7
Ⅶ. Installation……………………………….….…... 7
Ⅷ.Track by 900D web based tracking software………..…8
Ⅸ. Application…………………………………….… 11
Ⅹ.Specification………………………………....……11
Command set………………………………………12

2
 VT600X USER MANUAL
Attention

1. Make sure to read this manual carefully before using this product.
2. Please insert the SIM card before installing, and make sure the SIM card has no password, otherwise the
tracker will not work normally.
3. Please make sure that all the cables of the tracker has been connected rightly, and then connect the tracker to
host power. Must not install or take down the tracker when it is power on. If you found any troubles or
omissions about the connections of cables, please cut off power first, otherwise you will easily damage the
tracker.
4. The tracker works in wireless communications, so please cut off the host power before your vehicles entering
fuel depot and dangerous material place.
5. The tracker’s work voltage is 9V-30V. Please use the tracker in the scope of work voltage.
6. The host of GPS tracker is a low-power wireless transmitter and receiver. It receives and sends radio
frequency signal when it is working.
7. To avoid electromagnetic interference or uncompatible configuration, please stop using your tracker in the
noticed place.
GPS Vehicle Tracker
◆Hardware Description
1. Host Tracker

2. Start up
Put the SIM card in place and installed the tracker in the car, the red indicator is on. About 40 seconds, the
unit will begin to work and acquire the GSM signals as well as the GPS signals, and the red indicator will keep
flashing every 2 seconds when the GSM module is no communication. When the blue indicator is light, the unit
has been located.
◆Main functions
1. Positioning and Tracking: Through the on-line Positioning Platform or the cell phone to locates at times, and
get the working status. You can choose the Positioning Platform by yourself.
2. Triggering Emergency Alarm: When there is a emergency happened on the vehicle, you can put on the button
and the installed unit will send out alarm to the authorized numbers.
3. Remote controlling oil and circuit: you can control the oil and circuit via the unit by SMS in anywhere and
anytime.
4. Remote Monitoring: In anywhere and anytime, call the phone number in the unit, when it connects, you can
monitor the sound around 5 meter.

3
 VT600X USER MANUAL
5. Movement Alert: Send SMS to the unit to start the movement alert function. When the vehicle is moving, the
unit will send the movement alert to all authorized numbers.
6. Overspeed Alert: Send SMS to the unit to start the movement alert function. When the vehicle is overspeed,
the unit will send the overspeed alert to all authorized numbers.
7. Geo-fence: Set up a geo-fence for the unit to restrict its movements within a district. The unit will send the
message to all authorized numbers when it breaches the district.
8. Restart the unit: send SMS to resume the default of unit.
9. Auto Track: You can set up auto track by SMS or on-line positioning platform.
10. Mileage statistics; ACC checking; cutting off power and alarm.
11. Compatible with the original anti-theft alarm: It will send SMS alarm after the original anti-theft alarm
warning.
﹡Modify the IP and Port of Communication Protocol for different on-line positioning platform
◆Set up
2. Add authorized number (Can set 5 authorized number)
Send “admin+password+space+authorized number”
Example:Send SMS “admin123456 13612345678”. "admin" is instruction, "123456" is password,
"13612345678" is authorized number. It will reply “admin ok!”. You can set 5 authorized phone number
Maximum.
3. Delete authorized number
Send “noadmin+password+space+authorized number”
Example:Send SMS “noadmin123456 13612345678”. "noadmin" is instruction, "123456" is password,
"13612345678" is authorized number. It will reply “noadmin ok!”.
Send SMS “requestdeleteadmin” deleted all authorized number.
4. Change the Password
Send SMS: “password+old password+space+new password” to change the password.
Example: Send SMS “password123456 138138”. "password" is instruction, "123456"is old password,
"138138" is new password. Password must be six digits. Tracker’s initial password is 123456.
5. Resume the initial password
If you forget your password, you can resume the initial password 123456.
Send “resumepassword” to the tracker, the tracker will resume the initial password. If there is no authorized
numbers, all numbers can resume initial password. If there is already authorized numbers, only the authorized
numbers can resume initial password.
6. Control Oil
Send SMS “stopoil+password” to control oil. For example send SMS: stopoil123456
"stopoil" as instruction, "123456"as password.
To supply the oil again, send SMS “supplyoil+password” to the unit. For example, send
4
 VT600X USER MANUAL
SMS “Supplyoil123456” to the tracker. "Supplyoil" as instruction, "123456" as the password.
7. Control Circuit
Send SMS “stopelec+password” to control circuit. For example send SMS: “stopelec123456”.
"stopoil" as instructions, "123456" as the password.
To supply the circuit again, send SMS “supplyelec+password” to the unit. For example, send
SMS “Supplyelec123456” to the tracker. "supplyelec" as instruction, "123456" as password.
8. Switch between “tracker” and “monitor”
Send SMS “tracker+password” to the unit, it will reply “tracker ok!”. For example send SMS “tracker123456”.
In this mode, you can get position SMS by call tracker. Default :tracker
Send SMS “monitor+password” to the unit, and it will reply “monitor ok!” and switch to “monitor” mode. For
example send SMS: “monitor123456”. In this mode, you can monitor tracker by call tracker card number.
9. “Monitor”
There are three modes for monitor.
1) All Monitor Mode: Send SMS “allmonitor” to the unit, the unit will return to this mode. In this mode, any
number can monitor this unit.
2) Restrict Monitor Mode: Send SMS “restrictmonitor” to the unit, the unit will return to this mode. In this
mode, authorized number can monitor this unit.
3) Close Monitor Mode: Send SMS “closemonitor” to the unit, the unit will return to this mode. In this mode, all
numbers can not monitor this unit.
10. Movement alert
Set up: The user can send SMS “move+password” to the unit, then the unit will reply “move ok!” .In case of
such a movement, it will send SMS “move+Geo-info” to the number.
For example, send SMS “move123456” to the unit. "move" as instructions, “123456”as password.
Cancel: Send SMS “nomove+password” to deactivate the movement alert.
Default radius is 200 meters, if GPS tracker moves out this radius, then it will send SMS alert.
11. Overspeed alert
Set up: Send SMS “speed+password+space+080” to the unit (support the speed is 80km/h).
Example, send SMS “speed123456 080”. "speed" as instruction, "080" as limit speed, “123456”as password.
Cancel: Send SMS “nospeed+password” to deactivate the overspeed alert.
12. Geo-fence
Set up a geo-fence for the unit to restrict its movements within a district. The unit will send the message to the
authorized numbers when it breaches the district.
Set up: The user can Send SMS “stockade+password+space+MinLatitude,MinLongitude;MaxLatitude,
MaxLongitude” to unit to set the restricted district. In case of breach, it will send SMS “stockade! + geo-info” to
the authorized numbers.
For example send SMS “stockade123456 22.548123,114.081234;22.549123,114.082234” to the unit.
Remark: The first latitude & longitude is coordinate of min of the Geo-fence, while the second latitude &
longitude is the coordinate of the max. It will alarm one time in each setting.
Cancel: Send SMS “nostockade+password” to deactivate this function.
5
 VT600X USER MANUAL
This function will be out of effect after the unit moves outside the district.
13 . Restart the tracker.
Send SMS “reboot+password” to the tracker. For example“reboot123456”.The tracker will be restarted. It will
reply “system will reboot...”.
14. Enquiry Positioning
Send SMS “position” to the unit, then the unit will send SMS with real-time longitude and latitude to the cell
phone.
If you have set authorized phone number, then GPS tracker will only send message to authorized phone number.
If you do not set authorized phone number, then it can reply to any number.
15. Modes switch between “telephone” and “web”
Set up: Send SMS “web+password” to device. For example, the password is 123456. Send SMS “web123456”
to the device, the device will reply SMS “set web ok”. After this, the tracker will report the GPS data to IP
address. Default :web
If you want to send GPS data to telephone, you can send SMS “telephone+password” to device, the device will
reply “set telephone ok”. And then, the device will send GPS data to your telephone by SMS.
Relations diagram:

16. Modify IP address and port

The IP address and port of the tracker can be modified and transferred data to other platform. Send SMS “ ip+
ip address+port+port value” to the unit. If the platform’s IP address and port is 58.64.205.22 and 7000, send
SMS “ip58.64.205.22port7000” to the tracker. It will reply “set IP address and PORT ok.”. After this, device
will send GPS data to this IP and Port.Default ip:58.64.205.22 port:7000
17. Set APN
Case 1 (No apn user name and apn password)
In order to send GPS data to IP address, you still must set mobile network Access Point Name (APN). If you
don’t know the APN, you can consult local network service supplier. The format of set APN is “apn+password
+space+apn name”. For example you send SMS “apn123456 cmnet” to the device. The device will reply SMS
“Set APN ok.” Default APN:cmnet
Case 2 (Need apn user name and apn password)
1.Send SMS “apn+password +space+apn name”

6
 VT600X USER MANUAL
Example:apn123456 cmnet

2.Send SMS “user+space+apn user name+space+apn password”

Example: user telecom abc1234

“user” is command, “telecom” is APN user name, “abc1234” is APN password. After send SMS, tracker will
reply “Set GPRS User and Password ok . ” .

18. Set country time zone

In the default, tracker reply position SMS time is UTC time. After you can set zone time, tracker will reply the
time of your country. The format is “zone+password+space+time zone value”. For example, “zone123456 8” is
set east 8 time zone. Time zone value ranges from -12 to 12. One time zone stands for one hour. “zone123456
-8” is set west 8 time zone. After send SMS, tracker will reply “Set Time Zone OK.”.Default time zone: 0
19. Set ACC open and close send data interval
You can set the interval of send data when ACC open and close. The format of set ACC open interval is
“accon+time interval”. For example “accon 007” stand for when ACC open send data for every 7 seconds.
Default : 15 seconds
The format of set ACC close interval is “accoff+time interval”. For example “accoff 480” stand for when
ACC close send data for every 480 seconds. Default : 480 seconds.
20. Set ACC open and close send SMS notify
You can set the SMS notify of when ACC on and off. The format of set is “accnotify+1 or 0”. For example
“accnotify1” stand for when ACC on and off send SMS to authorized numbers. “accnotify0” stand for close send
SMS notify. In order to use this function, you must set authorized numbers.
21. Get GPS Info with Google Format
You can get latitude and longitude with Google website format. So you can open map directly by mobile. The
format of SMS is “google”. After you send SMS, tracker will reply GPS info with google website format.
22. Set call reply SMS format
You can set reply SMS format after you call tracker. The format of SMS is “geosms+1 or 2”.
Example:“geosms1” set reply SMS format as “position”. “geosms2” set reply SMS format as “google”.
◆Installation diagram of The Tracker

7
 VT600X USER MANUAL

◆GPS Vehicle Tracker Installation

GPS tracker should be installed by technical professional of local service centre. Without permission, the user
cann’t repair and move the tracker randomly. If users do, any unfortunated damage should be compensated by
himself.
Installation steps (caution: the following installation should under no power, otherwise will be dangerous)
1.Power supply line: The red wire connects 12V“+”;Black wire connects to 12V“-”
2. Wire for cutting off oil of the tracker(Yellow Wire)
Yellow wire connects the relay pin 86; 85 pin connect to 12 V DC , 87a pin and 30 pin in series power supply
circuits. Caution: Wrong connection of yellow wire will damage the tracker.
3. Wire for cutting off circuit of the tracker(White Wire)
White wire connects relay pin 86; 85 pin to 12 V DC, 87a pin and 30 pin are in series power supply circuits.
Caution: Wrong connection of yellow wire will damage the tracker.
4. Emergency triggering (SOS) alarm (Blue Wire)
The blue wire connects the positive of the alarm button, and the black wire connects the negative of the alarm
button.
5. Vehicle door detect, high level trigger(If you need low level trigger,please tell us) (Orange Wire)
The orange wire connects with Door sensor.

8
 VT600X USER MANUAL

Power supply

Lock Controller

Orange
(Door closed)Lock Unlock (Door open)
Lock Switch

Picture a.

b. --Æ

Picture a. Use car Lock Controller Connect and state diagram.(Door closed/Open)
Picture b. Door sensor Connect and state diagram (Door closed/Open)
6.Purple Wire (User Define)

Track by 900D web based tracking software

Enable GPRS
Set APN
Send the SMS to the tracker as following format
Command Remark

Set APN: Case 1 (No apn user name and apn password)
Command format: apn+password+space+apn name default password:123456
apn : Command code
123456: password, default 123456
cmnet: APN, is gateway to connect
For example: apn123456 cmnet
internet, Each country is different, please
contact your SIM card provider for APN
name.
Set APN: Case 2 (Need apn user name and apn password)

9
 VT600X USER MANUAL
1.Command format: apn+password+space+apn name default password:123456
apn : Command code
123456: password, default 123456
cmnet: APN, is gateway to connect
For example: apn123456 cmnet
internet, Each country is different,
please contact your SIM card provider
for APN name.
user+space+apn user name+space+apn
2.Command format:
password
user: Command code
For example: user telecom abc1234 telecom: is GPRS user name
abc1234: is GPRS password

Set IP and Port

Send the SMS to the tracker as following format:
Command Remark
Command format: ip+ip address+port+port value
For example: ip58.64.205.22port7000 ip : Command code
58.64.205.22 900D Platform server IP
7000 900D Platform server software
Port

Upload data in preset time when ACC ON

Send the SMS to the tracker as following format:
Command Remark
Case 1:
Command format: accon+time interval
For example: Accon007 accon : Command code
In this example: VT600X will send
location every 7 seconds when car
moving(ACC ON).

Upload data in preset time when ACC OFF

Command Remark
Command format: accoff+time interval
For example: accoff480 accoff : Command code
In this example: VT600X will send
location every 480 seconds when car
stop(ACC OFF).

Please go to http://www1.igpstracking.net/

Enter the user name and password we provided.

10
 VT600X USER MANUAL
Enter the user name and password we provided.
After log in, please go to “Vehicle Manager-Vehicle List”

You will see the below window

Please click “Add” button, you will see the below window:

License Plate: Define by yourself; you can enter A-Z number or Numeric

Very Important Note: Terminal ID and Plate number are unique on the software, you can add once only, you
need to delete it from database before adding it again. Only admin account can delete id from database, general
user cannot. You do not need to delete and re-add if the device cannot work on software, because it's caused by
your wrong sms setting, not the software.

Terminal Type: Do not choose.

SIM card: the SIM card phone number you put in VT600X or any number.

Terminal ID: On the vehicle of VT600X, you can find the “Terminal ID”.

Very Important Note: Please do not omit the minus if there's a minus before the terminal ID.

Or

11
 VT600X USER MANUAL

Click "Submit", and then you add the GPS tracker VT600X successfully on the software 900D.

Wait few seconds, and you will see the GPS Tracker online icon on software

Put a check mark on the device, and right click, you will see the menu as below picture. Now you can track
online.

Attention: For 900D GPS Software, "Monitor" and "Number Plate" must be checked till the font becomes
blue, then the GPS tracker will update location automatically on map.Like below picture:

◆Application
1. Vehicle Rental/Special Tracking System
2. Finance and Insurance Business Tracking System
3. Car Commanding and Dispatching System
4. Heavy Construction Vehicles Tracking Device
5. Shipping Cargoes Tracking
◆Specs.

12
 VT600X USER MANUAL
Content Specs.
Dim. 87 * 64 * 26 (mm)
Weight 495g
Network GSM/GPRS/GPS
Band 900/1800MHz or 850/900/1800/1900MHz
GPS chip SiRF III chip
GSM/GPRS Module SIM300 or SIM340
GPS sensitivity -159dBm
GPS accuracy 5m
Reacquisition 0.1s
Cold status 45s
Time To First Fix
Warm status 35s
Hot status 1s

Work Voltage DC 9V－30V

Battery Chargeable changeable 3.7V / 1.2Ah Li-ion battery

Standby work current < 30mA

Storage Temp. -40°C to +85°C

Operation Temp. -20°C to +70°C

Humidity 5%--95% non-condensing

◆Command Set

No. Function SMS Reply

Add
2 Admin123456 13612345678 Admin ok
Number
Delete
3 Noadmin123456 13612345678 Noadmin ok
Number
Change
4 Password123456 138138 Change password ok
password
Resume
5 resumepassword Resume password ok
password
Stopoil123456 Stop oil ok
6 Control oil Supplyoil123456 Supply oil ok

Control Stopelec123456 Stop electricity ok

7 circuit Supplyelec123456 Supply electricity ok
Switch Tracker123456 Tracker ok
between
8 “tracker”
and Monitor123456 Monitor ok
“monitor”

13
 VT600X USER MANUAL
AllMonitor Set all monitor ok

monitor RestrictMonitor Set restrict monitor ok

9 mode
CloseMonitor Set close monitor ok

Movement Move123456 Move ok

10 alert Nomove123456 Cancel move ok

Overspeed Speed123456 080 Speed ok

11 alert Nospeed123456 Cancel speed ok

Geo fence Stockade123456 coordinate;coordinate Set stockade ok

12 alert Nostockade123456 Cancel stockade ok
Restart
13 Reboot123456 System will reboot
tracker
Enquiry
14 position GPS info
position

Set auto Telephone123456 Set telephone ok

15
track mode Web123456 Set web ok
Set ip and
16 ip58.64.205.22port7000 set IP address and PORT ok
port
17 Set APN Apn123456 cmnet Set apn ok
Set APN
user name Set GPRS user name and password
18 and User telecom abc1234 ok
password
Set time
19 Zone123456 8 Set time zone ok
zone
Set ACC Accon007 Set ACC ON Interval OK.
open and
20 close Accoff480 Set ACC OFF Interval OK.
interval
Set ACC Accnotify1 Set ACC Notify OK.
open and
21
close SMS Accnotify0 Set ACC Notify OK.
notify
Get Google
22 format GPS Google GPS info with Google website format
info
Set reply
23 Geosms1/Geosms2 Set Geo SMS Format OK
SMS format

14
 VT600X USER MANUAL
TP(IP Address).P(Port)DD(Tracker
ID)F(Send fail quantity)S(Send
Read All success quantity) mm dd yy(Device
24 TCP
Parameters version
date)E(English)C(Chinese)HJ(Standa
rd version)

M:(mileage)A:C(apn
Read APN
25 info name)U:AC:(Upload data in preset
info
time)G:0001

15