SAG - Electrical Installation and Maintenance NC II

TESDA-OP-QSO-02-F07
Rev. No. 00-03/01/17
Reference. No.
Unique Learners Identifier
- - - -
SELF ASSESSMENT GUIDE
Qualification: ELECTRICAL INSTALLATION AND MAINTENANCE NC II

Performing roughing-in activities, wiring and cabling works for
Units of single-phase distribution, power, lighting and auxiliary systems
Competency Install Electrical Protective devices for distribution, power,
covered: lighting, auxiliary, lightning protection and grounding system
Install Wiring Devices of Floor and Wall Mounted Outlet Lighting
Fixture/Switches and Auxiliary Outlets
Instruction:
 Read each of the questions in the left-hand column of the chart.
 Place a check in the appropriate box opposite each question to indicate your answer.
Can I? YES NO
Performing roughing-in activities, wiring and cabling works for single-phase
distribution, power, lighting and auxiliary systems
 Communicate and confirm instructions for the preparation
of work activity to ensure clear understanding*
 Interpret electrical plan and detailed drawing*
 Identify and check to ensure that tools, equipment and
personnel protective equipment needed to electrical system*
 Identify and check auxiliary equipment, if it works correctly and
are safe to use in accordance with established procedures*
 Use safety harness or PPE properly*
 Bend and install type of conduit and cable tray as per
job requirement.*
 Perform correct procedures for installation of electrical
auxiliary system in line with job requirements*
 Ensure work is completed in an agreed scheduled time
in accordance with the quality standard.*
 Respond to unplanned events or conditions accordingly*
 Install conduit and fittings in accordance with standard *
 Perform installation qualification (IQ) activities*
 Perform operational qualification (OQ) activities*
ELCEIM215-0917 1
Electrical Installation and Maintenance NC II
Install Electrical Protective devices for distribution, power, lighting,
auxiliary, lightning protection and grounding system
 Communicate and confirm instructions for the preparation of
work activity to ensure clear understanding*
 Interpret electrical plans and detailed drawing*
 Identify and check to ensure that tools, equipment and PPE
needed to electrical system and by auxiliary equipment
works correctly and are safe to use in accordance with
established procedures*
 Follow safety procedures and the use of safety harness*
 Perform correct procedures for the installation/mounting
configuration of electrical protective devices and
grounding system*
 Respond to unplanned events or conditions accordingly*
 Select the types of lighting fixture and auxiliary outlet for the
installation*
 Undertake ongoing checks of quality of work in accordance
with instructions and requirements*
 Terminate/Splice conductors/wires in accordance with the
existing electrical standards*
 Perform final checks to ensure that work conforms to
instructions and drawing/diagram. *
 Perform the installation economically*
 Perform commissioning activities*
Install Wiring Devices of Floor and Wall Mounted Outlet Lighting
Fixture/Switches and Auxiliary Outlets
 Read and interpret drawings in accordance with job requirements*
 Set the lay-out and dimension of electrical drawing or
wiring diagram. *
 Select and identify correct rating, quantity, sizes and type of
wiring devices, switches, lighting fixture and convenience outlet*
 Identify the specifications of materials, tools and equipment
 Fill up properly requisition forms according to list of materials,
tools and equipment
 Follow safety procedures according to enterprise and government
regulations and select the correct PPE in line with safety
requirements*
 Identify defective and/or substandard electrical materials
and report to immediate supervisor*
 Lay out, mount and install electrical components, wiring materials
such as conduit and fittings in accordance with standards*
 Install wiring protective devices and grounding system properly*
ELCEIM215-0917 2
 Install the different types of lighting fixtures/switches as per
wiring diagram*
 Follow work schedule to ensure job is completed on time
in accordance to a quality standard and minimum wastage
 Seek further instructions from immediate supervisor in case
of unplanned events or conditions occurring*
 Undertake with strict compliance ongoing checks of quality of
the work in accordance with instructions and requirements
 Perform the installation economically*
 Perform commissioning activities*
I agree to undertake assessment in the knowledge that information gathered will only be
used for professional development purposes and can only be accessed by concerned
assessment personnel and my manager/supervisor.
Date:
Candidate’s Name & Signature

yEvaluated by:
Qualified for Assessment
Not yet Qualified for Assessment
AC Manager
Date:
ELCEIM215-0917 3

SAG - Electrical Installation and Maintenance NC II

Uploaded by

Copyright:

Available Formats

SAG - Electrical Installation and Maintenance NC II

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

SAG - Electrical Installation and Maintenance NC II

Uploaded by

Copyright:

Available Formats

TESDA-OP-QSO-02-F07

Rev. No. 00-03/01/17

SELF ASSESSMENT GUIDE

Qualification: ELECTRICAL INSTALLATION AND MAINTENANCE NC II

 Install conduit and fittings in accordance with standard *

 Perform installation qualification (IQ) activities*

 Perform operational qualification (OQ) activities*

Candidate’s Name & Signature

You might also like