LG Spring 2011 Mini Split Air Conditioner Training PDF
LG Spring 2011 Mini Split Air Conditioner Training PDF
LG Spring 2011 Mini Split Air Conditioner Training PDF
Mini‐split‐ Why so different
This chart shows the amount of power, both residential and
commercial, consumed by the HVACR industry. The large
portion of power that we consume makes it essential to use the
best technology we can find to reduce our consumption. The
high efficiency rating and low amp draw, coupled with variable
speed compressor, makes inverter technology one of the best
answers to our energy consumption.
Mini‐split‐ Why so different
The constant speed compressor that we are used to working
with is either on at full power or off. The inverter compressor
will slow down as it gets closer to the set point. This gives it a
longer run time at much lower power consumption. The longer
run time also gives better temperature control and humidity
control.
The thermistors in the indoor and outdoor unit sense the
operating parameters. The board analyses this data and sets
the fan and compressor speed along with the EEV setting to
meet the demand. Therefore the machine is constantly
sampling and adjusting to the most efficient speed needed at
the time.
Mini‐split‐ Why so different
This loop will continue until the thermostat is satisfied or the
unit is turned off. If there is a problem the unit will give an
error code.
Mini‐split‐ Why so different
When the unit first starts, the board is receiving information
from the thermistors. There is a short time that the expansion
valve will appear to hunt. As the system settles the valve will
become more stable. Then depending on model, it will only
reposition every four or six minutes.
The electronic expansion valve is a four pole stepper motor. In
the following diagram you can see how each pole is energized.
The valve has about 1400 steps that it can be set to. It never
fully closes that can be precisely set to monitor the
refrigeration flow as needed.
Mini‐split‐ Why so different
By alternating before magnets you can regulate the EEV valve
as close as one cog of the wheel.
Mini‐split‐ Why so different
Mini‐split‐ Why so different
How does inverter technology actually work? We take our line
voltage AC and go through a circuit called a diode bridge. The
output of the bridge is a DC power source. This is called the
converter circuit. From here that DC is sent through another
circuit that brings it back to a chopped or square wave AC. This
circuit also makes it appear as three phase power. Each phase
of this power fires the bank of transistors. Each bank of
transistors is wired to one winding of the compressor. By firing
two banks of transistors and powering two windings at one
time and having one winding not energized a potential
difference is created and the compressor rotates. The faster
these transistors fire, the faster the compressor rotates, this is
called frequency.
Mini‐split‐ Why so different
This picture shows just the bank of transistors feeding the
windings of the motor.
The actual speed of the compressor can be calculated as above
Although BLDC motors are practically identical to permanent
magnet AC motors, the controller implementation is what
makes them DC. While AC motors feed sinusoidal current
simultaneously to each of the legs (with an equal phase
distribution), DC controllers only approximate this by feeding
full positive and negative current to two of the legs at a time.
The major advantage of this is that both the logic controllers
and battery power sources also operate on DC, such as in
computers and electric cars. In addition, the approximated sine
wave leaves one leg undriven at all times, allowing for back‐
EMF‐based sensorless feedback.
Mini‐split‐ Why so different
This is the wave out of the inverter circuit, going to the
compressor. Notice it is a square wave. As it is a wave, it will
have a frequency that can be controlled by the inverter.
The following is the compressor wave form with the signal to
the electronic expansion valve added. As was stated earlier the
two signals have to be perfectly synchronized. The only
difference you can see is a voltage difference.
Mini‐split‐ Why so different
This is shown by the difference in the heights of the signals.
Mini‐split‐ Why so different
Frequency can be read on a standard meter by going on any of
the three compressor leads and reading to ground. Most of our
meters have a frequency scale, we have not had the reason to
use it previously.
The following startup sheet can be used to record initial
information that will become the basis for your follow‐up
service. It is essential to know that the unit was properly
installed. We will talk more about this Later in the manual.
Mini‐split‐ Why so different
• CONDENSER UNIT VOLTAGE : RATED ______ APPLIED ______
• EVAPORATOR VOLTAGE A/C OR D/C RATED _______ APPLIED ______
• COMPRESSOR : ROTARY _____ INVERTER
• FLAIR NUTS TORQUED TO ________FT/LBS
• LEAK CHECK COMPLETED Y/N EVACUATED TO _______ MICRONS
• LINE SET SIZE LIQ. ____ SUCTION _____ LENGTH _____FT.
• REFRIGERANT ADJUSTMENT LENGTH ‐25 FT= ____X .22 OZ/FT= ____OZ. REF.
ADDED
• REFRIGERANT ADJUSTMENT 25FT – LENGTH = _____X.22OZ/FT= ____OZ. REF.
REMOVED
• INVERTER REFRIGERANT ADJUSTMENT SINGLE ZONE OVER 43FT X .22 OZ/FT‐‐‐‐‐‐
‐‐ ADDED
• INVERTER DUAL ZONE ADJUSTMENT OVER 74 FT. ‐‐‐‐‐‐‐‐‐‐ADDED DIPSWITCH SET
Y/N
• INVERTER TRI AND QUAD ZONE ADJUSTMENT OVER 123FT. ‐‐‐‐‐‐‐‐ADDED.
DIPSWITCH SET Y/N
• BOTH REFRIGERANT LINES INSULATED Y/N CONDENSATE INSULATED AS
NEEDED Y/N
• EVAPORATOR SECURE ON WALL Y/N LEVEL Y/N
• CEILING MOUNT ALL BOLTS TIGHT Y/N LEVEL Y/N
• CONDENSATE DRAIN FLOW GOOD Y/N CONDENSATE PUMP INSTALLED Y/N
ALL ELECTRICAL CONNECTIONS TIGHT Y/N IN CODE COMPLIANCE Y/N
• CONDENSER BOLTED DOWN AND VIBRATION PADS INSTALLED Y/N
Mini‐split‐ Why so different
• SERVICE PORTS OPEN AND LEAK CHECKED Y/N
• FAN OPERATION : JET COOL Y/N CHAOS Y/N FAN ONLY Y/N
• COOLING MODE : COMPRESSOR TIME DELAY _____MIN.
• COMPRESSOR CYCLES ± 1 DEG.FROM ROOM TEMP. Y/N
• DOES FAN GO TO LOW SPEED WHEN THE STAT IS SATISFIED Y/N
• AFTER TEN MINUTE RUN TIME: PRESSURE HI_____ LO ____
• COOLING MODE : EVAP COIL AIR IN ____ AIR OUT ____ ∆T ____
• HEAT MODE : DOES THE DOMPESSOR CYCLE ± 3 DEG. FROM ROOM TEMP. Y/N
• DOES EVAP FAN DELAY UNTIL COIL INLET REACHES 82 DEG. Y/N
• DOES FAN GO TO SET SPEED AFTER 4 MIN. Y/N LOW WHEN STAT IS SATISFIED
• HEAT MODE EVAP AIR IN ____ AIR OUT ____∆T
• CONDENSER : MODEL # ___________ SER#____________
EVAPORATOR: MODEL # ___________ SER # _________ As a companion to the startup
sheet we are supplying a service checklist. Either of these lists can be modified to fit your
company needs.
Mini‐split‐ Why so different
Mini‐split‐ Why so different
Mini‐split‐ Why so different
As was stated in the beginning of the manual these units
are thermister controlled. The first two types of
thermistors that we will discuss are air thermistors and
pipe thermistors. Air thermistors have a plastic or
neoprene looking sensing bulb. Pipe thermistors have a
metallic sensing bulb.
Mini‐split‐ Why so different
The thermister plugs have very small openings making it
very difficult to take readings with normal meter leads.
Mini‐split‐ Why so different
These thin spring wire leads will fit into the plug opening
and also make contact with the metal on the side of the
plug. Being able to clamp them on, it leaves both hands
free to adjust the meter.
Mini‐split‐ Why so different
Another method that can be used or meter leads with
very fine points that can make contact with the small
metal area on the back side of the plug.
Mini‐split‐ Why so different
If you are meter does not have the clamping spring clips,
or the fine pointed meter leads, one alternative would be
to solder straight pins or sewing needles into the end of
the wire at shown below. This will give you a wire end that
you can use to obtain your readings.
Thermistors can be checked by reading ohms or DC volts. The
most common method used to check ohms. Once you have
obtained the ohm reading, you can go to the thermistor chart
and determine the temperature at the sensor of the thermistor.
Mini‐split‐ Why so different
Mini‐split‐ Why so different
As you can see by the chart there are differences in value
between air and pipe thermistors. at 32° The air thermistor
reads 33.82 Ω the pipe thermistor at 32° reads 16.76Ω. One of
the easiest ways to check a thermistor used to put the sensing
end in a glass of ice water. If you also put your temperature
sensing lead from your meter in the glass of ice water you can
check the calibration of your meter while you are checking the
thermister. Two of the easy checks on thermistors are as
follows. At 77° the air thermistor we’ll read 10KΩ. The pipe
thermistor will read 5KΩ.
By reading the pipe thermistor resistance and converting it to a
temperature we now have the temperature of the refrigerant
in that pipe. This value can be taken to a standard pressure/
temperature chart and you can read the pressure of the
refrigerant in that line. Since these units are critical charge and
have much less refrigerant in them than a standard unit it is
essential to use this method to obtain refrigerant pressures.
When we ohm out the thermistor and go to the temperature/
pressure chart to obtain our pressure readings there is
absolutely no loss of refrigerant.
All manufacturers of mini‐splits have the error codes for open
or shorted thermistors. There are no error codes for out of
tolerance thermistors. Since the Mini‐split‐or controlled
through the board using the inputs from thermistors we cannot
Mini‐split‐ Why so different
maintain proper temperature control if the thermistor is out of
tolerance. Many times control boards have been changed
simply because a thermistor was out of tolerance and no one
thought to check it because there was no error code displayed.
Mini‐split‐ Why so different
Many of our wiring diagrams simply show where to plug each
component into the main control board. Most of our
troubleshooting will be at the control board. It will consist of
removing a plug from the board and checking the component,
and on the other side checking the output of the board. If the
component does not plug directly into the board, we may go to
the plug for that component and do our check there.
At the three wire compressor plug we can check voltage to
each lead and the frequency going to the compressor.
Mini‐split‐ Why so different
With a plug open on the plug side going to the compressor we
can check the windings of the compressor. We can check
winding to winding and winding to ground. Since this is a three
phase compressor, there is no capacitor. If we were working on
a standard compressor we would be able to shut off the power
and read the capacitor at the receptacle side of this plug.
Mini‐split‐ Why so different
The outdoor fan motor uses a 6pin connector. If we open this
connector, on the board side we can check for power. If we
disconnect power we can check between the yellow and brown
wire and read our capacitor. The windings of the motor can be
checked on the receptacle side of the connector.
Mini‐split‐ Why so different
The capacitor for the outdoor fan motor is located below the
control board assembly. This is one of the reasons it is
advantageous to check components out at the plug rather than
having to dig down to where they’re located.
Mini‐split‐ Why so different
Each component that plugs into the board will either have a
unique size of plug or a different color. It is difficult to miss wire
these boards.
WARNING: WHEN DISCONNECTING POWER, THE CONTROL
BOARD REMAINS HOT UNTIL THE LED LIGHTS GO DIM. THIS
MAY TAKE AS LONG AS TWO MINUTES
Mini‐split‐ Why so different
The machine pictured here is setup for up to three indoor units.
This is shown by the three sets of brass fittings for the
refrigerant lines on the side of the machine.
There’s one reversing valve located below the control board
assembly. The coil is replaceable, and can be checked out from
the plug at the board.
Mini‐split‐ Why so different
Mini‐split‐ Why so different
Spring 2011 Mini Split AC