Flat Slab Design (SK)

Download as xls, pdf, or txt
Download as xls, pdf, or txt
You are on page 1of 5

FLAT SLAB DESIGN

Spreadsheet Limitation:
- Suitable for flat slab without Drop
- Both square and rectangular slab can be used
- Calculation based on 1 m strip
- Square RC pile provided
- fcu should always less than 40 N/mm2

1. Estimate the dimension x


Slab Thickness 150 mm fcu 25 N/mm2
DL 3.6 kN/m 2 fy 460 N/mm2
LL 7.5 kN/m2 Rc pile 200 mm Sq
Total DL + LL 11.10 kN/m2
Capacity per pile 400 kN
Proposed Öx2 6.00 m
Provide x 2.00 x 2.00 m2

2. Re-bar Design width


Dead load = 14.4 kN
Live load = 30.0 kN
Total load on a single pile = 44.4 kN ok
Ultimate load ,F = 68.2 kN
Equivalent distributed stress ,n = 17.0 kN/m2
Effective span ,L = 1.9 m

Center of first span


Max. +ve moment for column strip = +0.55(0.083FL)
(per m) = 5.81 kNm

k = 0.02
z = 0.98 d
= 0.95 d
As = 132.84 mm2/m
Suggested DA6(283)
Provide steel area 1341.00 mm2/m

Center of interior span


Max. +ve moment for column strip = +0.55(0.071FL)
(per m) = 4.97 kNm

k = 0.02
z = 0.98 d
= 0.95 d
As = 113.64 mm2/m
Suggested DA6(283)
Provide steel area 1341.00 mm2/m

First support
Max. -ve moment for column strip = +0.75(0.063FL)
(per m) = 6.01 kNm

k = 0.02
z = 0.98 d
= 0.95 d
As = 137.50 mm2/m
Suggested DA6 283
Provide steel area 1341.00

Interior support
Max. -ve moment for column strip = +0.75(0.055FL) 0
(per m) = 5.25 kNm

k = 0.02
z = 0.98 d
= 0.95 d
As = 120.04 mm2/m
Suggested DA6 283
Provide steel area 1341.00

3. Punching Shear Check


At column perimeter
Perimeter = 800.00 mm
Shear Force = F-An
= 67.48 kN
0.8 * Öfcu = 4.00 < 5 N/mm2
Shear limit = 4.00 N/mm2
Shear Stress = 1.15V/(ud)
= 0.84 N/mm2 OK

At Critical Perimeter, 1.5d


Perimeter = 2180.00 mm
Shear force = 63.10 kN
Shear stress = 0.289 N/mm2
d = 115.00 mm
As = 1341.00
400/d = 3.48
100As/bd = 1.17
Vc = 0.908 N/mm2 OK

DA7 TOP
DA6
+ + +

+ + +
2 DA6(283)

+ + +

2.00
plan typical slab section
plan
BRC mm2/m
DA10 785
DA9 636
DA8 503
DA7 385
DA6 283
DA5 196

Note : assume pile enter 25 mm into the slab


Therefore ,actual thickness that portion = h-25
However, no cover that part & thus,eff. d still h-35

BRC mm2/m
DA10 785
DA9 636
DA8 503
DA7 385
DA6 283
DA5 196

DA7 TOP
DA6

150
mm

typical slab section

You might also like