Hi-Pon 200Ht Cui: Product Description

HI-PON 200HT CUI
TECHNICAL DATA SHEET
PRODUCT DESCRIPTION Hi-Pon 200HT CUI is a two-pack, high build epoxy phenolic coating with
excellent resistance to chemicals and acts as a corrosion resistant barrier for
steel when use at elevated temperatures.
INTENDED USE Hi-Pon 200HT CUI is specially designed for use as an external coating for
protection of steelwork from corrosion under thermal insulation (CUI) when
exposed to wet/dry cycling conditions. It is also suitable to protect insulated &
uninsulated pipework and process vessels operating at temperatures up to
200°C.
GENERAL PROPERTIES Colour : White & Grey

Gloss Level : Matt
Volume Solids, % : 64 ± 2 %
Specific Gravity : 1.46 kg/l (Mixed)
Flash point : Base: 13.3°C Hardener: 35°C Mix: 13.3°C
VOC : 313 g/L (EPA Method 24)
Typical Thickness : 100 – 200 ųm dry film
: 156 – 313 ųm wet film
All surfaces should be clean and free from contamination. The surface should
SURFACE PREPARATION
be assessed and treated in accordance with ISO 8504. Oil or grease should be
removed in accordance with SSPC-SP1 solvent cleaning.
Abrasive Blast Cleaning

Abrasive blast cleaning to Sa 2½ (ISO 8501-1:2007) to achieve surface profile
50 - 75 µm. If oxidation has occurred between the blasting and application of
this product, the surface should be re-blasted to the specified visual standard.
Surface defect revealed by the blast cleaning process should be ground, filled
or treated in the appropriate manner.
Damaged Area
Damage area should be prepared with abrasive blast cleaning to Sa 2½ (ISO
8501-1:2007). When abrasive blasting in small area is not possible, mechanical
cleaning to St 3 (ISO 8501-1:2007) is acceptable. After the surface preparation,
the application of Hi-Pon 200HT CUI can be performed.
Hi-Pon 200HT CUI should be applied over a surface that is dry and free from
all contamination and must be applied within the overcoating intervals specified
(refer to application section for details).
Version002 Issue date: 30/05/18 Page 1 of 4

HI-PON 200HT CUI
Other Surfaces
The coating may be used on other substrates. Please contact your local
Nippon Paint office for more information.
CONDITION DURING Avoid paint application when the temperature is below 10°C and relative
APPLICATION humidity is over 85%. The temperature of steel surface must be a minimum
3°C above dew point of surrounding air.
APPLICATION GUIDE Mixing Ratio : Base: hardener = 6 : 1 (by volume)

Base and hardener should be mixed
thoroughly before use.
Pot Life : 25°C

4 Hrs
Theoretical Coverage : 3.2 m2/litre at 200 µm DFT
Thinner : Hi-Pon Epoxy Thinner
APPLICATION METHOD Airless spray is recommended for application. Brush is recommended for stripe
coating and small areas. Care must be taken to achieve the specified dry film
thickness.
APPLICATION DETAILS Airless Spray : Tip Size : 0.018” – 0.026”

Pressure at nozzle : 140 – 170 kg/cm2
Typical Thickness : 100 – 200 ųm dry film

: 156 – 313 ųm wet film
Drying Time : Substrate Temperature 25°C 40°C

Surface Dry 60 mins 30 mins
Through Dry 6 hrs 4 hrs
Cured 10 days 7 days
Dry to recoat (min) 6 hrs 4 hrs
Dry to recoat (max) 21 days 14 days
The given data must be considered as guidelines only. The actual drying
time/times before recoating may be shorter or longer, depending on film
thickness, ventilation, humidity, underlying paint system, requirement for early
handling and mechanical strength etc. A complete system can be described on
a system sheet, where all parameters and special conditions could be included.

HI-PON 200HT CUI
RECOMMENDED Hi-Pon 200HT CUI is self-priming and normally applied as a 2-coat system
PAINTING SYSTEM which therefore not recommended for application over other primers/topcoats.
For the choice of coating system for different application, refer to the product
brochure or contact Nippon Paint for professional recommendation.
PACKAGING Unit Base Hardener

Vol Container Size Vol Container Size
5L 4.2 L 5L 0.7 L 1L
20 L 16.8 L 20 L 2.8 L 5L
STORAGE Shelf life : Part A: 12 months (25°C)

Part B: 12 months (25°C)
Subject to re-inspection thereafter. Higher temperature during storage may

reduce the shelf life and may lead to gelling in the tin.
Store in tightly closed container in a dry, cool and well ventilated space, keep
away from sources of heat and ignition.
 This product is intended for use of professional applicators. Refer to the

SAFETY PRECAUTION
safety information display on the container and in the safety data sheet
(SDS) before using the product.
 Use this product in well-ventilated area, avoid skin contact, spillage on the
skin should immediately be removed with suitable cleanser, soap and
water.
 Eye should be well flush with water and seek for medical attention
immediately upon contact with this product.
 During the application, naked flame, welding operation and smoking is not
allowed. Adequate ventilation should be provided.
 If you have any doubt regarding the suitability of use, refer to Nippon
Paint for further advice.
DISCLAIMER The information in this data sheet is given to the best of Nippon Paint’s
knowledge and practical experience. Users may consult with Nippon
Paint on the general suitability of the product for their needs and
specific application practices though it remains each user’s
responsibility to determine the suitability of the product for the user’s
particular use. The condition of the substrate and application are not
within Nippon Paint’s control. Therefore no implied conditions,
warranties or other terms will apply to the Product. Nippon Paint does
not and cannot warrant the results which the user may obtain by using
HI-PON 200HT CUI
the product. In no event will Nippon Paint be liable to the user for any
kind of loss (whether direct or indirect) even if Nippon Paint was
previously advised of it. In line with Nippon Paint’s policy for
continuous development, Nippon Paint reserves the right to modify the
product and the information in this data sheet without prior notice. It is
the user’s responsibility to check with Nippon Paint for the latest
version of this data sheet. This data sheet has been translated into
various languages. In the event of any inconsistency, the English
version shall prevail.

Hi-Pon 200Ht Cui: Product Description

Uploaded by

Copyright:

Available Formats

Hi-Pon 200Ht Cui: Product Description

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Hi-Pon 200Ht Cui: Product Description

Uploaded by

Copyright:

Available Formats

HI-PON 200HT CUI

TECHNICAL DATA SHEET

GENERAL PROPERTIES Colour : White & Grey

Abrasive Blast Cleaning

Version002 Issue date: 30/05/18 Page 1 of 4

APPLICATION GUIDE Mixing Ratio : Base: hardener = 6 : 1 (by volume)

Pot Life : 25°C

Theoretical Coverage : 3.2 m2/litre at 200 µm DFT

Thinner : Hi-Pon Epoxy Thinner

APPLICATION DETAILS Airless Spray : Tip Size : 0.018” – 0.026”

Typical Thickness : 100 – 200 ųm dry film

Drying Time : Substrate Temperature 25°C 40°C

Version002 Issue date: 30/05/18 Page 2 of 4

PACKAGING Unit Base Hardener

STORAGE Shelf life : Part A: 12 months (25°C)

Subject to re-inspection thereafter. Higher temperature during storage may

 This product is intended for use of professional applicators. Refer to the

Version002 Issue date: 30/05/18 Page 4 of 4

You might also like