Scribd
Upload
34 views3 pages

Liquidcrystal: Int Int Int Int Int Int Int Int

This Arduino code controls the speed of a fan based on temperature readings from an LM35 temperature sensor. It uses an LCD display to show the current temperature and fan speed percentage. The fan speed is mapped to a range between two temperature thresholds, with the speed increasing linearly from 0 to 100% as the temperature rises from the minimum to maximum thresholds. An LED also turns on if the temperature exceeds the maximum threshold.

Uploaded by

Teguh Priyono
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
34 views3 pages

Liquidcrystal: Int Int Int Int Int Int Int Int

This Arduino code controls the speed of a fan based on temperature readings from an LM35 temperature sensor. It uses an LCD display to show the current temperature and fan speed percentage. The fan speed is mapped to a range between two temperature thresholds, with the speed increasing linearly from 0 to 100% as the temperature rises from the minimum to maximum thresholds. An LED also turns on if the temperature exceeds the maximum threshold.

Uploaded by

Teguh Priyono
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

#include

//source: https://www.electroschematics.com/9540/arduino-fan-speed-controlled-temperature/
LiquidCrystal lcd(7,6,5,4,3,2);
int tempPin = A1; // the output pin of LM35
int fan = 11; // the pin where fan is
int led = 8; // led pin
int temp;
int tempMin = 30; // the temperature to start the fan
int tempMax = 70; // the maximum temperature when fan is at 100%
int fanSpeed;
int fanLCD;

void setup() {
pinMode(fan, OUTPUT);
pinMode(led, OUTPUT);
pinMode(tempPin, INPUT);
lcd.begin(16,2);
}

void loop() {
temp = readTemp(); // get the temperature
if(temp < tempMin) { // if temp is lower than minimum temp
fanSpeed = 0; // fan is not spinning
digitalWrite(fan, LOW);
}
if((temp >= tempMin) && (temp <= tempMax)) { // if temperature is higher than minimum
temp
fanSpeed = map(temp, tempMin, tempMax, 32, 255); // the actual speed of fan
fanLCD = map(temp, tempMin, tempMax, 0, 100); // speed of fan to display on LCD
analogWrite(fan, fanSpeed); // spin the fan at the fanSpeed speed
}
if(temp > tempMax) { // if temp is higher than tempMax
digitalWrite(led, HIGH); // turn on led
} else { // else turn of led
digitalWrite(led, LOW);
}

lcd.print("TEMP: ");
lcd.print(temp); // display the temperature
lcd.print("C ");
lcd.setCursor(0,1); // move cursor to next line
lcd.print("FANS: ");
lcd.print(fanLCD); // display the fan speed
lcd.print("%");
delay(200);
lcd.clear();
}

int readTemp() { // get the temperature and convert it to celsius


temp = analogRead(tempPin);
return temp * 0.48828125;
}

#include

//source: https://www.electroschematics.com/9540/arduino-fan-speed-controlled-temperature/

LiquidCrystal lcd(7,6,5,4,3,2);

Int tempPin = A1; // the output pin of LM35

Int fan = 11; // the pin where fan is

Int led = 8; // led pin

Int temp;

Int tempMin = 30; // the temperature to start the fan

Int tempMax = 70; // the maximum temperature when fan is at 100%

Int fanSpeed;

Int fanLCD;

Void setup() {

pinMode(fan, OUTPUT);

pinMode(led, OUTPUT);

pinMode(tempPin, INPUT);

lcd.begin(16,2);

Void loop() {

Temp = readTemp(); // get the temperature

If(temp < tempMin) { // if temp is lower than minimum temp

fanSpeed = 0; // fan is not spinning


digitalWrite(fan, LOW);

If((temp >= tempMin) && (temp <= tempMax)) { // if temperature is higher than minimum temp

fanSpeed = map(temp, tempMin, tempMax, 32, 255); // the actual speed of fan

fanLCD = map(temp, tempMin, tempMax, 0, 100); // speed of fan to display on LCD

analogWrite(fan, fanSpeed); // spin the fan at the fanSpeed speed

If(temp > tempMax) { // if temp is higher than tempMax

digitalWrite(led, HIGH); // turn on led

} else { // else turn of led

digitalWrite(led, LOW);

Lcd.print(“TEMP: “);

Lcd.print(temp); // display the temperature

Lcd.print(“C “);

Lcd.setCursor(0,1); // move cursor to next line

Lcd.print(“FANS: “);

Lcd.print(fanLCD); // display the fan speed

Lcd.print(“%”);

Delay(200);

Lcd.clear();

int readTemp() { // get the temperature and convert it to celsius

temp = analogRead(tempPin);

return temp * 0.48828125;

You might also like