Scribd
Upload
93 views14 pages

Analog & Digital Electronics: Course No: PH-218 Lec-23: Operational Amplifiers

1) An operational amplifier (op-amp) is a high-gain differential amplifier with very high input impedance and low output impedance. 2) Op-amps are used to perform mathematical operations like summation, subtraction, differentiation, and integration. Common applications include voltage amplification, oscillators, filters, and instrumentation circuits. 3) Negative feedback is needed when using op-amps in linear applications to reduce voltage gain and provide stable operation as an amplifier.

Uploaded by

Ali Hasan Sifat
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
93 views14 pages

Analog & Digital Electronics: Course No: PH-218 Lec-23: Operational Amplifiers

1) An operational amplifier (op-amp) is a high-gain differential amplifier with very high input impedance and low output impedance. 2) Op-amps are used to perform mathematical operations like summation, subtraction, differentiation, and integration. Common applications include voltage amplification, oscillators, filters, and instrumentation circuits. 3) Negative feedback is needed when using op-amps in linear applications to reduce voltage gain and provide stable operation as an amplifier.

Uploaded by

Ali Hasan Sifat
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 14

Analog & Digital Electronics

Course No: PH-218

Lec-23: Operational Amplifiers

Course Instructor:

 Dr. A. P. VAJPEYI

Department of Physics,
Indian Institute of Technology Guwahati, India 1
Operational amplifier (OP-AMP)
An Op-Amp is a very high gain differential amplifier with very high
input impedance (typically a few Mega ohm) and a low output
impedance (less than 100Ω)

 If the signal applied to the input terminal, results in opposite


polarity output then input terminal is called inverting input, and
if output is of same polarity input terminal is called non-
inverting input.
2
Operational amplifier (OP-AMP)
 Earlier, op-amp were used primarily to perform mathematical
operation such as summation, subtraction, differentiation and
integration etc. so named as op-amp.

 Typical application of op-amp includes – voltage amplitude change,


oscillators, filter circuits and in instrumentation circuits.

3
Characteristics of an Ideal Operational amplifier
Ideal op-amp has following characteristics -

��Input Resistance Ri= ∞


��Output Resistance Ro= 0
��Voltage Gain A = ∞
��Bandwidth = ∞
��Perfect balance i.e vo= 0 when v1= v2
��Characteristics do not drift with temperature

4
Concept of Virtual Ground +Vout
 An Op-Amp has a very high gain +VCC
typically order of 105.
Slope: Ad
-Vi
 If power supply voltage Vcc =15V +Vin
Then maximum input voltage which +Vi
can be applied
-VCC
Vd = Vcc /Ad = 15/ 105 = 150µV

i.e. Op-Amp can work as a linear


amplifier (from +Vi to –Vi) if input
voltage is less than 150µV. Above that
Op-Amp saturates.

 if V1 is grounded then V2 can not be


more than 150 µV which is very very
small and close to ground.

 Therefore V2 can also be considered at ground if V1 is at ground.


Physically V2 is not connected to the ground yet we considered V2 at
ground that is called virtual ground. 5
Need of negative feedback in op-amp
 Any input signal slightly greater than zero drive the output to
saturation level because of very high gain.

 Thus when operated in open-loop, the output of the OPAMP is


either negative or positive saturation or switches between positive
and negative saturation levels (comparator). Therefore open loop
op-amp is not used in linear applications.

 With negative feedback, the


voltage gain (Acl) can be reduced
and controlled so that op-amp can
function as a linear amplifier.

 In addition to provide a control and stable voltage gain, negative


feedback provides control of input & output impedance and
amplifier bandwidth.
6
Op-Amp as a Comparator
 A comparator is a type of op-amp that compares two input voltage
and produces an output in either of two states indicating the greater
than or less than relationship of the input.

 When the inverting voltage is larger than the noninverting voltage


the comparator produces a low output voltage (-Vsat). When the
inverting output is less than the non-inverting input the output is
high (+Vsat).

vO = -Vsat if vi > VR
= + Vsat if v i < VR

If open loop gain of op-amp is 105 then


differential input voltage of only 0.25
mV will produce output voltage of = 25V.
However, most of op-amp have
limitation of maximum power supply
voltage of 15V hence device would be
driven to saturation.
7
Op-Amp as a Comparator
If VR = 0, then slightest input voltage (in
mV) is enough to saturate the OPAMP and
the circuit acts as zero crossing detector.
The more the open loop gain of OPAMP,
the smaller the voltage required to saturate
the output. If vd required is very small then
the characteristic is a vertical line.

Output Bounding

The output voltage of a comparator can be


limited to a value less than the saturation
voltage by connecting a zener diode with
the comparator. This process of limiting the
output voltage is called bounding.

8
Comparator: Output Bounding
Two zener diode connected back to back with a comparator limit the output
voltage to the zener voltage plus the voltage drop (0.7V) of the forward bias
zener diode, both positively and negatively.

9
Noninverting Amplifier
 The differential input to the op-amp (Vin-Vf) will be amplified by the open
loop gain and produces an output voltage.

Vo = Ad (Vin − V f )
R1
V f = βVo = Vo
R1 + R f
Vo Ad 1
= =
Vin 1 + βAd β

 Since βAd >> 1

Vo 1 R1 + R f Rf
= = Vo = (1 + )Vin
Vin β R1
R1
10
Voltage Follower
 The lowest gain that can be obtained from a non-inverting
amplifier with feedback is 1.

 When the non-inverting amplifier gives unity gain, it is called


voltage follower because the output voltage is equal to the input
voltage and in phase with the input voltage. In other words the
output voltage follows the input voltage.

Vo = Vin
 Voltage follower has very high input
impedance and very low output
impedance hence used as a buffer
amplifier for interfacing high impedance
source and low impedance load.
11
Inverting Amplifier or Scale Changer

If R1 = Rf then vO = -v1, the circuit behaves like an inverter.

If Rf / R1 = K (a constant) then the circuit is called inverting amplifier or scale


changer voltages.
12
Summing Amplifier
For an ideal OPAMP,
v1 = v2. The current drawn
by OPAMP is zero. Thus,
applying KCL at v2 node

i1 + i2 + i3 = i f
Va Vb Vc Vo
+ + =
Ra Rb Rc R f

Rf Rf Rf Rf
Vo = −( Va + Vb + Vc ) If Ra = Rb = Rc = R; then Vo = − R (Va + Vb + Vc )
Ra Rb Rc
If Rf = R then vO = -(va +vbf +vc ), the circuit behaves like a inverting summer.

If R / Rf = n where n is number of inputs then the circuit behave like a


averaging amplifier.
13
Summing Amplifier as D/A converter
A digital to analog (D/A) converter is a weighted summing circuit that
produces an output equal to the weighted sum of inputs.

The weight is same as the gain of the channel.

Rf Rf Rf
Vo = −( Va + Vb + Vc )
Ra Rb Rc

Binary Input Output


000 0 Vin
001 -0.125
010 -0.50
011 -0.625
100 -1.00
101 -1.125
110 -1.50
111 -1.625 Vout 14

You might also like