TA2092AN

TOSHIBA Bipolar Linear Integrated Circuit Silicon Monolithic

TA2092AN
Power Driver IC for CD Player

The TA2092AN is a power driver IC developed for CD players.

This IC have built-in 4 channel BTL power amplifiers which
drives focus-coil, tracking-coil for 3-beam pick-up head, disc
motor and feed motor.

Features
· 4 channel BTL linear drivers
· Fixed voltage gain: GV = 15.5dB (typ.)
· High output power
· Thermal shutdown circuit
· Input reference voltage short protection
· Operating voltage range: VCC (opr) = 4.5~10.0 V (Ta = 25°C) Weight: 1.2 g (typ.)

Block Diagram

1 2001-08-28
 TA2092AN
Terminal Explanation
Terminal
Symbol Function Equivalent Circuit
No.

Power GND
1 PW GND ● Connected to substrate.
● pin 1, 12, 13, 24 are connected inside.

2 OUT (−) 1 Inverted output for CH1

Supply terminal of output stage for CH1

3 PVCC1 ● Supply terminal of output stage are not connected to other
channel terminal.

4 OUT (+) 1 Non-inverted output for CH1

Input for CH1

5 VIN1
● Not biased inside

Input reference voltage

6 VRI ● Under condition of VRI ≤ 1.1 V, internal bias circuit is shut off.
● No signal input condition: VRI = VIN

Output reference voltage

7 VCI
● VOUT = VCI = (VCC−VF) /2

8 VIN2 Input for CH2

9 OUT (+) 2 Non-inverted output for CH2
10 PVCC2 Supply terminal of output stage for CH2 Same as channel 1

11 OUT (−) 2 Inverted output for CH2

12 PW GND Power GND
13 PW GND Power GND
14 OUT (−) 3 Inverted output for CH3
15 PVCC3 Supply terminal of output stage for CH3 Same as channel 1

16 OUT (+) 3 Non-inverted output for CH3

17 VIN3 Input for CH3
18 S GND Supply terminal of small signal GND ―
19 S VCC Small signal GND ―
20 VIN4 Input for CH4
21 OUT (+) 4 Non-inverted output for CH4
22 PVCC4 Supply terminal of output stage for CH4 Same as channel 1

23 OUT (−) 4 Inverted output for CH4

24 PW GND Power GND

2 2001-08-28
 TA2092AN
Maximum Ratings (Ta = 25°C)

Characteristics Symbol Rating Unit

Supply voltage VCC 14 V

Power dissipation PD (Note 1) (2) (Note 2) W
Operating temperature Topr −30~85 °C
Storage temperature Tstg −55~150 °C

Note 1: Mounted on 50 mm × 50 mm × 1.6 mm size board with copper area 60 % over.

Note 2: Derated above Ta = 25°C, in the proportion of 62.5 mW/°C.

Electrical Characteristics (unless otherwise specified, VCC = 8 V, RL = 5 Ω, f = 1 kHz,

VBIAS = 1.65 V, Rg = 3.3 kΩ, Ta = 25°C)
Test
Characteristics Symbol Test Condition Min Typ. Max Unit
Circuit
Operating voltage VCC ― ― 4.5 8.0 10.0 V
Quiescent current ICCQ ― Vin = 0, RL = OPEN 30 50 70 mA
Input offset current IIN ― VIN = 1.65 V ― 0 200 nA
VRI terminal offset current I10 ― VRI = 1.65 V ― 30 60 µA
Output offset voltage VOS ― Rg = 3.3 kΩ −68 ― 68 mV
Reference output voltage VOUT － ― ― 3.6 ― V
Maximum output voltage VOM ― ― 7 8 ― Vp-p
Voltage gain GV ― VIN = 100 mV 14.5 15.5 16.5 dB
Frequency response fc ― Vin = 100 mVrms ― 100 ― kHz
Total harmonic distortion THD ― Vin = 100 mVrms ― −50 ― dB
Slew rate S.R. ― Vout = 2 Vp-p ― 1.0 ― V/µs
Cross talk C.T. ― Vout = 1 Vrms ― −60 ― dB
Ripple rejection ratio R.R. ― frip = 100 Hz, Vrip = 100 mVrms ― −60 ― dB
Thermal shut down temperature TTSD ― Chip temperature ― 150 ― °C
VRI~GND short protection voltage VRI OFF ― ― 0.9 1.1 1.3 V

3 2001-08-28
 TA2092AN
Test Circuit

4 2001-08-28
 TA2092AN
Precaution Use
· Input stage
· Input stages are consisted of differential circuit of PNP Tr, and have built-in base current compensation
circuit.
· Built-in driver
· Each channel driver consists of BTL configuration linear amplifier.
Voltage gain is fixed: GV = 15.5dB (typ.)
Voltage loss for output stage is 2 VBE = VCE (sat) for positive cycle, VCE (sat) for negative cycle, because of
no-bootstrap circuit. So, output DC voltage is designed as less than 1/2 VCC.
· VRI terminal
· VRI is reference voltage terminal for input signal.
If reference voltage from servo IC drop less than 1.1 V, protection circuit operates and shut off bias circuit
inside. This operation is to prevent load from moving undesireably in case of VRI drop for accident or some
reason.
· VCI terminal
· Output DC voltage is determined by circuit of this terminal inside as;
VCI = VOUT (DC) = (VCC−VF) /2
· Output signal dynamic range is depend on VCC. On the other hand, input signal dynamic range is determined
by VRI as mentioned and voltage gain is fixed inside. So, maximum output voltage does not increase as VCC
increases.
· Because of BTL configuration, Ripple Rejection Ratio does not improve not much when capacitor is connected
to VCI terminal to GND.
· GND
· Large signal GND is for output stage and small signal GND is for stages from input circuit to pre-output
stage.
· These GND pins are not connected inside.
· The heat of power dissipation is transferred to PCB, through these PW-GND Pin, because, 1, 12, 13, 24 pin
are connected each other and to substrate of Pellet to connected copper foil area as large as possible.
· Oscillation preventive capacitor
· We recommend to use the capacitor of 0.1 µF, between each output terminals. But perform the temperature
test to check the oscillation allowance, since the oscillation allowance is varied according to the causes
described below.
1) Supply voltage
2) Ambient temperature
3) Load impedance
4) Capacity value of condenser
5) Kind of condenser
6) Layout of Printed board
· We recommend to connect Pass-condenser, which is about 47 to 100 µF between VRI terminal and GND.
· VCI terminal is recommend to use “OPEN”.

5 2001-08-28
 TA2092AN
Package Dimensions

Weight: 1.2 g (typ.)

6 2001-08-28
 TA2092AN

RESTRICTIONS ON PRODUCT USE 000707EBF

· TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor
devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical
stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of
safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of
such TOSHIBA products could cause loss of human life, bodily injury or damage to property.
In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as
set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and
conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability
Handbook” etc..

· The TOSHIBA products listed in this document are intended for usage in general electronics applications
(computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances,
etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires
extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or
bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or
spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments,
medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in this
document shall be made at the customer’s own risk.

· This product generates heat during normal operation. However, substandard performance or malfunction may
cause the product and its peripherals to reach abnormally high temperatures.
The product is often the final stage (the external output stage) of a circuit. Substandard performance or
malfunction of the destination device to which the circuit supplies output may cause damage to the circuit or to the
product.

· The products described in this document are subject to the foreign exchange and foreign trade laws.
· The information contained herein is presented only as a guide for the applications of our products. No
responsibility is assumed by TOSHIBA CORPORATION for any infringements of intellectual property or other
rights of the third parties which may result from its use. No license is granted by implication or otherwise under
any intellectual property or other rights of TOSHIBA CORPORATION or others.

· The information contained herein is subject to change without notice.

7 2001-08-28
This datasheet has been download from:

www.datasheetcatalog.com

Datasheets for electronics components.