M7..dw.. en PDF

Download as pdf or txt
Download as pdf or txt
You are on page 1of 25

OPERATING MANUAL

EagleBurgmann Mechanical Seal (M.S.)

M7../dw.. HSM7N../dw..
HSM7../dw.. LASERTEC-M7N/dw..
M7N../dw.. M7S../dw..

(dw = specified shaft diameter)


Applies to all mechanical seals of the same series

These instructions are intended for the assembly, operating and supervising
personnel and should be kept at hand on site.

PLEASE READ this manual carefully and OBSERVE the information contained as to:

 Safety  Transport / Storage  Information about the product


 Installation  Operation  Servicing

If there are any unclear points please contact EagleBurgmann by all means!

en M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. / July 7, 2016 Rev. 14


Operating Manual
M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. page 2 / 25

Table of Contents

Keywords and Symbols ....................................................................................................... 3

GENERAL SAFETY NOTES............................................................................................... 4


Instructions for worker's protection ...................................................................................... 5
Notes on explosion protection ............................................................................................. 5

TRANSPORT / STORAGE .................................................................................................. 6


Transport ............................................................................................................................. 6
Storage, "mothballing" (long term storage) .......................................................................... 7

INFORMATION ABOUT THE PRODUCT ........................................................................... 9


Manufacturer and country of origin ...................................................................................... 9
Type designation ................................................................................................................. 9
M7S../dw.............................................................................................................................. 9
Materials ............................................................................................................................ 10
Designated use.................................................................................................................. 10
Operating limits.................................................................................................................. 11
Operating conditions .......................................................................................................... 11
Drawings, diagrams ........................................................................................................... 11
Description......................................................................................................................... 12
Required space, connecting dimensions ........................................................................... 12
Versions............................................................................................................................. 13
Supply of M.S. ................................................................................................................... 13
Emissions .......................................................................................................................... 13

INSTALLATION ................................................................................................................ 14
General notes dealing with assembly utilities .................................................................... 14
Preparation for assembly ................................................................................................... 15
Assembly / installation ....................................................................................................... 17
Supply connections ........................................................................................................... 20

OPERATION ..................................................................................................................... 21
Safe operation ................................................................................................................... 21
Start-up .............................................................................................................................. 21

SERVICING ....................................................................................................................... 22
Maintenance ...................................................................................................................... 22
Directives in case of failure ................................................................................................ 22
After-sales service by EagleBurgmann .............................................................................. 22
Reconditioning (repair) ...................................................................................................... 23
Disassembly / removal ...................................................................................................... 23
Spare parts ........................................................................................................................ 24
Required details for enquiries and orders .......................................................................... 24
Disposal of the mechanical seal ........................................................................................ 25
Copyright ........................................................................................................................... 25

en M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. / July 7, 2016 Rev. 14


Operating Manual
M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. page 3 / 25

Keywords and Symbols

Following symbols for particularly important information are used:

"Attention, please pay special attention to these sections of text"

DANGER! Draws attention to a direct hazard that will lead to injury or death
of persons

WARNING! Draws attention to the risk that a hazard could lead to serious
injury or death of persons

CAUTION! Draws attention to a hazard or unsafe method of working that


could lead to personal injury or damage to equipment

ATTENTION! Identifies a potentially dangerous situation. If it is not avoided the


product or something in its vicinity could be damaged

IMPORTANT! Identifies tips for use and other particularly useful information.

en M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. / July 7, 2016 Rev. 14


Operating Manual
M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. page 4 / 25

GENERAL SAFETY NOTES

Any person being involved in assembly, disassembly, start-up, operation and


maintenance of the mechanical seal must have read and understood this
operating manual and in particular the safety notes. We recommend the user
having this confirmed.

EagleBurgmann mechanical seals are manufactured to a high quality level and they
have a high working reliability. Yet, if they are not operated within their intended
purpose or handled inexpertly they may create risks.

The machine has to be set up in such a way that seal leakage can be led off and
disposed of properly and that any personal injury caused by spurting product in the
event of a seal failure is avoided.

Any operation mode that affects the operational safety of the mechanical seal is not
permitted.

Unauthorised modifications or alterations of the mechanical seal are not permitted.

Mechanical seals must be installed, operated, maintained and removed by


authorised, trained and supervised qualified personnel only. In case the
personnel has no long years of experience in handling with and operating of
mechanical seals and their supply systems, for this purpose, EagleBurgmann offers
corresponding seminars for achieving of the required knowledge.

The responsibilities for the respective jobs to be done have to be determined


clearly and observed in order to prevent ambiguous competencies from the point of
security.

Any work to be done on the mechanical seal is generally only permitted when the
seal is neither operating nor pressurised. The machine must be protected against
accidental start-up.

WARNING! Seals that have been used with hazardous substances must be properly
cleaned so that there is no possible danger to people or to the environment.

Apart from the notes given in this manual, the general regulations for worker's
protection and those for prevention of accidents have to be observed.

en M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. / July 7, 2016 Rev. 14


Operating Manual
M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. page 5 / 25

Instructions for worker's protection

WARNING! If the medium to be sealed and/or the supply liquid is subject to the
Hazardous Substances Regulation (GefStoffV), the instructions for handling
dangerous substances (safety data sheets to Directive 91/155/EEC) and the
accident prevention regulations have be observed.

Medium to be sealed and/or supply medium may escape if the seal fails. Injury of
persons and environment may be prevented by the user providing for splash
protection and wearing of safety goggles. Care has to be taken by the user for
proper disposal of the leakage. The user has to control these measures.

The user has to check what effects a failure of the mechanical seal might have and
what safety measures have to be taken to prevent personal injury or damage to the
environment.

Notes on explosion protection

Mechanical seals are mechanical parts, which are put in circulation for general
technical purposes. They are not components within the meaning of Directive
2014/34/EU.

The respective probation as to explosion protection for the provided temperature


class must be carried out during the conformity assessment of the machine, into
which the mechanical seal is installed, by the machine manufacturer.

In case the assessment is carried out by the end user, the respective additional
operating manual has to be requested from EagleBurgmann.

en M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. / July 7, 2016 Rev. 14


Operating Manual
M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. page 6 / 25

TRANSPORT / STORAGE
Transport
If not specified differently by contract, the EagleBurgmann standard packaging is
used which is suitable for dry transport by truck, train or plane. The warning signs
and notes on the packaging must be observed.

In addition, seaworthy packaging may become necessary.

Notes for income inspection:


 Check packaging for visible damage.
 Open packaging carefully. Do not damage or lose parts supplied separately.
 Check if consignment is complete (delivery note). Inform the supplier immediately
in writing if parts are damaged or missing.

The mechanical seal has to be protected from damage during transport and storage.
The transport case in which the seal is supplied is well suited for this purpose and
should be kept for a possible return transport.

ATTENTION! If the machine as well as the mechanical seal installed into the machine
are transported together, the shaft must be protected from deflection at all times,
shocks and axial displacement by means of a suitable machine support.
Damage at the M.S. caused by insufficient protection during transport is excluded
from the warranty.

en M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. / July 7, 2016 Rev. 14


Operating Manual
M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. page 7 / 25

Storage, "mothballing" (long term storage)

The following recommendations apply to all mechanical seals which have been
supplied and stored in their undamaged original packaging, as well as to seals
which have been installed in a machine (e.g. pump, compressor, agitator, etc.) but
have not yet been put into operation.

Mechanical seals and spare parts are super finished and repeatedly tested machine
elements. For storage special conditions have to be followed.

Sliding materials and secondary sealing elements are subject to material-specific and
time-based alterations (distortion, ageing) which might reduce the full efficiency of the
mechanical seals. Hence, this may be avoided by observing the storage instructions.

For the stock keeping of elastomers, special conditions are required. For all rubber-
elastic parts the rules of DIN 7716 resp. of ISO 2230-1973 (E) are valid.

Optimum conditions for storing of mechanical seals


 dust free
 moderately ventilated
 constant temperature
 relative air humidity below 65 %,
 temperature between 15 °C and 25 °C.

Protect the mechanical seal from


 direct exposure to heat (sun, heating)
 ultraviolet light (halogen or fluorescent lamps, sunlight, arc welding)
 presence or development of ozone (arc welding, mercury vapour lamps, high-
voltage devices, electric motors)
 risk of embrittlement of elastomeric materials

It must be recognised that a difference exists between:


 M.S. stored in the stock room
 M.S. installed in the machine, but not yet in operation.

en M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. / July 7, 2016 Rev. 14


Operating Manual
M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. page 8 / 25

 M.S. in the stock


IMPORTANT! Store the seal in the original packaging lying on a flat surface.

 Check the packaging periodically for damage.


 Sealings packed in plastic-foil with humidity indicators have to be checked every
8 weeks. The check has to be recorded.
 Packaging exceeding 50 % rel. humidity values must be sent to the manu-
facturer or the nearest EagleBurgmann service centre for inspection and new
packaging.

Unused stored mechanical seal under optimum conditions:


 For reasons of safety, after 3 years from delivery of the mechanical seal the M.S.
should be returned to EagleBurgmann resp. nearest EagleBurgmann Service
centre for
 Exchange of all secondary seals and springs
 Verification of the flatness of the faces
 Perhaps static pressure test.

 M.S. installed into the machine:


ATTENTION! "Mothballing" (long term storage) of the mechanical seals is not allowed.

In case of a "mothballing" (long term storage) of complete machines with mechanical


seals installed EagleBurgmann has to be contacted.
 Do not use corrosion protection agents.
 Risk of deposition and possibly chemical attack of the secondary seals.

Due to longer erecting times of newly designed plant the period between delivery of
the mechanical seal and its installation and start-up in the machine may exceed a
period of 2-3 years.

After 3 years at the latest and in good time before the planned start-up of the plant
the seal has to be dismantled sent to the manufacturer or the nearest
EagleBurgmann service centre where it can be checked and reconditioned, if
necessary.

EagleBurgmann does not accept any warranty for damage caused by improper
storage.

en M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. / July 7, 2016 Rev. 14


Operating Manual
M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. page 9 / 25

INFORMATION ABOUT THE PRODUCT


All technical information given is based on the results of extensive testing and on our
long term practical experience. However, in view of the great diversity of possible
applications the technical data can only be taken as being of approximate nature. We
can only guarantee the safe and efficient functioning in individual cases if we have
been comprehensively informed of the operating conditions to which they will be
subject, and if this has been confirmed in a separate written agreement.

Manufacturer and country of origin

EagleBurgmann Germany GmbH & Co. KG


Äußere Sauerlacher Str. 6-10
D - 82515 Wolfratshausen
Germany

Type designation

EagleBurgmann Mechanical Seal (M.S.)


M7../dw.. HSM7N../dw..
HSM7../dw.. LASERTEC-M7N/dw..
M7N../dw.. M7S../dw..
dw = specified shaft diameter

en M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. / July 7, 2016 Rev. 14


Operating Manual
M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. page 10 / 25

Materials

The materials of the mechanical seal depend on the application and are bound to the
customer order. They can be found on the drawing, and/or in the parts lists attached
to the documentation.

Designated use

This mechanical seal is exclusively designed for the use in the specified application.
A different utilisation or usage of the seal going beyond the specification is
considered contrary to its designated use and excludes a liability for possible
consequences by the manufacturer.

Operation of the seal under conditions lying outside the limits stated in paragraph
"Operating limits" is considered contrary to its designated use.

Should the mechanical seal be operated under different conditions or in a different


application EagleBurgmann must confirm that such a change is safe in advance of
subsequent operation.
 Changes to operating conditions have to be documented.

en M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. / July 7, 2016 Rev. 14


Operating Manual
M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. page 11 / 25

Operating limits

ATTENTION! Operating limits depending on the materials used.

Shaft diameter (dw) : 14 ... 100 mm


Temperature to be sealed (t1) : -50 ... +220 °C 1) 2)
Sliding speed (vg) : 20 m/s

Material combination : Carbon graphite / SiC


Pressure to be sealed (p1) : 25 bar g

Material combination : SiC / SiC


Pressure to be sealed (p1) : 16 bar g
1)
depending on the sliding materials
2)
depending on the elastomer materials

Please observe that the given operating limits interact, and therefore not all extreme
values can be called on simultaneously.

Beyond that, the range of application of the respective product depends on the
diameter, the materials used, the operation mode and the media to be sealed.

If there are any unclear points please contact EagleBurgmann.

Operating conditions
The exact operating data for the respective application, e.g. medium to be sealed,
operating pressure, operating temperature, speed, etc., are listed in the operating
manuals and the specification sheets of the machine manufacturer and/or the end
user.

The selection of the mechanical seal (type, suitability, materials) should be done by
EagleBurgmann staff or other authorised persons. A wrong selection by
unauthorised persons is not covered by EagleBurgmann's warranty.

Drawings, diagrams

The original assembly drawing in its latest edition (latest revision) only is decisive for
both the design of M.S. as well as the utilisation of this manual.

In the following description all figures in parentheses, e.g. (2) define the respective
part item no. in fig. 1. The part item no. may vary from those stated on the
corresponding assembly drawing.

en M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. / July 7, 2016 Rev. 14


Operating Manual
M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. page 12 / 25

Description

Fig. 1

 single seal
 unbalanced
 bi-directional
 rotating seal face (1.1)
 stationary seat (2)
 The sliding faces can be equipped with thermohydrodynamic relieving grooves
("HS" grooves). During run they support the formation of a lubricating film in the
sealing gap.
The M.S. are then named as HSM7../dw...
 "Super Sinus" spring (1.5)
 axial movability
dw < 25 mm ±1.0 mm
dw  25 … 63 mm ±1.5 mm
dw > 63 … 100 mm ±2.0 mm
 connecting dimensions to EN 12756
 torque transmission to the shaft by means of set screws with cup point (1.6)
Other torque transmissions are possible by means of special drivers, e.g. parallel
keys
(e.g. design version M7S2).

Required space, connecting dimensions


The required installation space for the mechanical seal is decisive for the design of
the housing parts by the machine manufacturer. The connecting dimensions have to
be checked by the machine manufacturer by means of the EagleBurgmann drawing
before mounting the mechanical seal.

en M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. / July 7, 2016 Rev. 14


Operating Manual
M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. page 13 / 25

Versions

The seal types mentioned before are also usable as multiple mechanical seals in
tandem arrangement together with a pressureless supply (buffer) fluid system
(API, plan 52) or as dual mechanical seals (back-to-back / face-to-face) together with
a pressurised supply (barrier) fluid system (API, plan 53) (also in combination with
seal types of other series). Consultation with the EagleBurgmann company is
recommended.

Supply of M.S.

The mechanical seal has to be constantly wetted by liquid medium. The medium to
be sealed must not damage the M.S. neither chemically (e.g. corrosion,
embrittlement) nor physically (e.g. erosion, abrasion).

For a safe operation of the mechanical seal we recommend applying at inboard the
most suitable type of circulation described in API 610 / 682. This measure protects
the seal cavity from deposition of solids.

To operate multiple seals special supply systems are required. Please contact
EagleBurgmann.

Emissions

A mechanical seal is a dynamic seal that cannot be free of leakage due to physical
and technical reasons. Seal design, manufacture tolerances, operating conditions,
running quality of the machine, etc. mainly define the leakage value. In fact,
compared to other sealing systems there is few leakage.

During the running-in phase of the M.S. an increased leakage may occur.
If the leakage amount does not decrease or if there are other malfunctions the
mechanical seal has to be shut down, removed and checked for reasons of safety.

The leakage can be liquid or gaseous. Its aggressiveness corresponds to that of the
medium to be sealed.

Leakage of the M.S. at outboard side has to be drained and disposed of properly.

IMPORTANT! Components which may have contact with the leakage have to be
corrosion-resistant or have to be adequately protected.

WARNING! If the medium to be sealed and/or the supply liquid is subject to the
Hazardous Substances Regulation (GefStoffV), the instructions for handling
dangerous substances (safety data sheets to Directive 91/155/EEC) and the
accident prevention regulations have be observed.

en M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. / July 7, 2016 Rev. 14


Operating Manual
M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. page 14 / 25

INSTALLATION
General notes dealing with assembly utilities
For cleaning:
 ethyl alcohol
 cellulose-tissue (no rag, no cloth!)
For applications free from silicone:
 cotton-tissue (no rag, no cloth!)
 clean cotton gloves

For lubricating:
 suitable lubricants
 Lubricants must be compatible with all media (e.g. medium to be sealed, supply,
flushing and/or cooling medium etc.), with those they get into contact with, and
they must not corrode the secondary sealing elements.
ATTENTION! Secondary sealing elements made of EP-rubber must never come into
contact with mineral oil-based lubricants (swelling, possibly decomposition).
 suitable synthetic lubricant for dynamic elastomeric secondary sealing elements
e.g. "TURMOPOL GREASE SH 2 D" make: Lubricant Consult (LUBCON).
 suitable lubricants (conform with FDA)
e.g. "TURMSILON LMI 5000" make: Lubricant Consult (LUBCON).
 chloride-free surfactants (e.g. sodium dodecyl sulphate (SDS)) or low-surface-
tension water for elastomeric bellows seals and static elastomeric secondary
sealing elements of seats
ATTENTION! For applications free from silicone:
 Lubricants must be free of silicones, fluorinated compounds which are able to
migrate, and tensides.

For installation:
 set of hexagon keys
 set of open end or ring spanners
 torque wrench
Additional for single seals:
 o-ring lifter
 cardboard discs to cover the sliding faces during installation
 hand screw press (compulsory for shaft diameter ≥80 mm)
 press-in tool (as usual for radial rotary shaft seals)

For sealing:
 Sealing agents for threads for pipe connections, e.g. "LOCTITE® Nr. 266" make:
LOCTITE Corporation

For securing:
 for bolts, set screws etc. use liquid screw retention, e.g. "LOCTITE® Nr. 243"
make: LOCTITE Corporation

en M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. / July 7, 2016 Rev. 14


Operating Manual
M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. page 15 / 25

Preparation for assembly

ATTENTION! To prevent damage to the seal, do not remove it from its packaging
until all the work described below has been completed.

Check the parts of the machine for:


 connecting dimensions, if available
tolerances of position and shape for
the connecting parts (see drawing)
 chamfered edges
(sliding cones i.e. 2 mm / 30° or in
accordance with EN 12756)
 radiused transitions
 mating fits fine finished:
Rz 10 µm (= N7 = CLA 63)
 shaft surface in the area of the
mechanical seal: Ra = 0.8 µm (= N6
= CLA 32)
 surface in the area of the
dynamically loaded o-ring
roughness: Rmax 5 µm (= N6 =
CLA 32) (e.g. component seals)
 surfaces for:
 static secondary sealing elements
fine finished: Rz = 10 µm (= N7 =
CLA 63)
 PTFE secondary sealing elements
fine finished: Rz = 5 µm (= N6 =
CLA 32)

Version "M7S2":
 Keyway in the shaft for torque transmission of M.S.
 Shoulder or stop device for the driver of the M.S. to take up axial forces

Check on the machine:


 damage of connecting surfaces to the M.S.
 mating dimensions, rectangularity and concentricity to the shaft axis.

 Fix the machine shaft in centric and axial position.

en M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. / July 7, 2016 Rev. 14


Operating Manual
M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. page 16 / 25

Type and quality of the shaft bearing have a major influence on the well-functioning
and the service life of the M.S.
Therefore, before installation of the M.S. both the
 concentricity accuracy of the shaft
 and the run-out accuracy between shaft and machine housing
have to be checked.

The maximum permitted axial displacements have to be considered, and the


instructions of the manufacturer have to be observed.

Concentricity accuracy of the shaft (acc. to DIN ISO 5199):


 Shaft diameters up to 50 mm: max. 0.05 mm
 Shaft diameters 50 mm - 100 mm: max. 0.08 mm
 Shaft diameters exceeding 100 mm: max. 0.10 mm

Eccentricity and run out as specified by EagleBurgmann!


Eccentricity of the inner surface of the seal
chamber to the shaft:
 max. 0.1 mm for seals with pumping screw
 max. 0.2 mm for seals without pumping screw

Run-out accuracy of the vertical contacting


surface between seal chamber and shaft axis:
 Shaft speed ≤ 750 rpm: max. 0.2 mm
 Shaft speed 1000 rpm: max. 0.15 mm
 Shaft speed 1500 rpm: max. 0.08 mm
 Shaft speed 3000 rpm: max. 0.025 mm

In case of installation into other machines the shown values apply as directive.

 Prepare the assembly place, take away any not required tool, cuttings, dirty
cleaning wool etc.

 Cover the work bench with a piece of clean, non-fibrous cardboard.

en M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. / July 7, 2016 Rev. 14


Operating Manual
M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. page 17 / 25

Assembly / installation

Mechanical seals are super-finished and repeatedly tested machine elements whose
handling during assembly requires special care during certain procedures,
particularly when dealing with sliding materials and elastomers.

For installation the assembly drawing has to be observed.

 Unpack the seal.


 If necessary, use suitable auxiliaries (e.g. crane, elevating machinery, lifting
device, eye bolts etc.).
ATTENTION! The regulations for the prevention of accidents have to be followed.

After having unpacked the mechanical seal:


 remove the protective covers from the sliding faces
 clean the sliding faces with ethyl alcohol and paper tissues
 check the parts for possible damage.
 Never place the seal faces or seats on their sliding faces without having covered
them adequately.
 Clean all parts thoroughly.

 Check before starting assembly:


 complete availability of all components by means of the drawing
 all components have to be clean and in perfect condition.

The order of assembly to install the mechanical seal into the machine depends on the
design of the machine and has to be determined by the machine manufacturer.
 If the machine manufacturer specified auxiliaries (jigs and fixtures) they have to be
used in accordance with the specifications of the manufacturer.

 The mechanical seal has to be installed under the cleanest conditions


and very carefully.
 Avoid unnecessary rotation of the shaft (damage of the sliding faces is
possible).
 Never use force during installation.
 Avoid knocking! Damage to mechanical seals has an adverse effect
on their safe operation.
 When fitting the PTFE-sealing elements in no case widen or
compress them. Otherwise, their sealing function cannot be ensured.
 Observe the notes on the current drawing if necessary please contact
EagleBurgmann.

en M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. / July 7, 2016 Rev. 14


Operating Manual
M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. page 18 / 25

 When using double-PTFE-wrapped o-rings care


has to be taken that the joint on the outer
wrapping faces against the assembly direction.
Otherwise there is a risk of the wrapping opening
and being pulled off, possibly resulting in seal
leakage.

IMPORTANT! For the assembly of o-rings made of solid PTFE considerable assembly
forces are required to compress them. Yet, these forces may result in permanent
deformations of seal components, in particular of the assembly fixtures. To
compress o-rings made of PTFE little force over an extended period of time has
to be applied (force x time = constant). If necessary, the fastening screws have to be
retightened several times.

ATTENTION! Sealing elements made of PTFE have to be used only once.

Possible installation order:

 Make sure that all sealing elements have been installed which contact the
surrounding machine parts.

If not described otherwise, the following parts have to be moistened slightly with
suitable lubricant during installation:
 o-rings in sliding contact with other parts when mounting the mechanical seal,
 shafts in the area of the mechanical seal,
 centring seats (centring diameters) for housing parts.
 Lubricants must be compatible with the medium to be sealed, and they must not
corrode the secondary sealing elements.
 Sealing elements made of EP-rubber must never come into contact with mineral
oil-based lubricants (swelling, possibly decomposition).

 Feed the degreased o-ring onto the seat.


If available:
 Mark the position of the rear slot at the seat, namely at the front side beside the
sliding face.
 Align the seat with the torque transmission pin.
 Cover the sliding face of the seat with a cardboard washer.
 Press the seat slowly and without interruption into its position.
 Use plenty of water or alcohol as lubricant.
 Use a mounting sleeve, if necessary.
 Remove the cardboard washer from the sliding face.
 Check the rectangular position of the seat.

en M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. / July 7, 2016 Rev. 14


Operating Manual
M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. page 19 / 25

 Feed the rotating unit with the lubricated sealing rings onto the shaft.
 Stick to the dimensions on the assembly drawing!
 Insert the degreased set screws with 1 drop each of liquid screw retention (e.g.
Loctite® 243)
 Fix the driver by tightening the set screws.
ATTENTION! Set screws with cup point must be used only once. Repeated fastening
endangers the safety of force transmission.

 Check the specified tightening torque with a torque wrench.

Version "M7S2":
 Insert the parallel key into the groove provided.
 Feed the rotating unit with the lubricated sealing rings onto the shaft.
 The parallel key in the shaft has to engage into the groove in the drive collar.

 Clean the sliding faces thoroughly with ethyl alcohol and paper tissues (no cloth,
no rags!).
 In case of material "BUKO" (carbon graphite) wipe it until the paper tissues stay
clean.
 Do not touch the sliding faces any longer with bare fingers.
 Do not lubricate the sliding faces but mount them in a clean and dry state.

 Mount the seal cover with the seat installed before.


 The fitting dimension shown on the drawing must be observed by all means.

 Any further assembly of the machine must be in accordance with the instructions
of the machine manufacturer.

en M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. / July 7, 2016 Rev. 14


Operating Manual
M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. page 20 / 25

Supply connections

ATTENTION! Sealing agents for threads (PTFE-tape, etc.) endanger the safe function of
the mechanical seal if they enter the seal chamber. When screwed connections are
opened take care by all means that sealing agents cannot enter the mechanical seal.

Supply piping:
 Use pipes of stainless steel or resistant material with a sufficient cross-section.
 Supply piping for liquids: min. 18x1.5 mm
 Supply piping for gases: min. 12x1.5 mm
 Impulse piping: min. 12x1.5 mm
 Clean the piping thoroughly.
 Fasten all pipe connections pressure-sealed.
 Install the pipes continuously rising, as short and as convenient as possible for
the flow to ensure self-venting.
 Avoid air inclusions and provide for venting connections, if necessary.
 For turns use pipe bends
 Fasten the pipes with appropriate pipe clips.
ATTENTION! If shutoffs in the piping to the seal are required, ball valves with torsion
lock have to be used.
ATTENTION! The operating manual of the supply system must be observed.

en M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. / July 7, 2016 Rev. 14


Operating Manual
M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. page 21 / 25

OPERATION
Safe operation

ATTENTION! If during an interruption of operation values deviating from the operating


conditions / operating limits the mechanical seal must be removed and checked
either at the manufacturer's or at the nearest service centre.

For a single mechanical seal the pressure in the seal chamber (stuffing box
pressure) has to be higher than the ambient pressure at the machine at any time.
Otherwise the machine will suck in air via the sliding faces, which will result in dry-
running and consequent failure of the mechanical seal.

During every state of operation the mechanical seal has to be constantly wetted by
the medium to be sealed in its liquid form, in particular when the machine is
started or stopped. The machine design has to be such to take this necessity into
consideration.

Damage due to dry-running is excluded from the warranty.

If the operation limit values and the instructions given in this manual are followed a
trouble-free operation of the mechanical seal can be expected.

Start-up
Safety checks before start-up
 Torque transmission between mechanical seal and shaft duly installed
 Supply connections tightened and pressure-sealed
 Disposal connections installed environmentally safe

For a safe operation of the mechanical seal we recommend applying at inboard the
most suitable type of circulation described in API 610 / 682. This measure protects
the seal cavity from deposition of solids.

 Fill and vent the machine by all means in accordance with the instructions of the
machine manufacturer.

 Now the seal is ready for operation.

To operate multiple seals special supply systems are required. Please contact
EagleBurgmann.

en M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. / July 7, 2016 Rev. 14


Operating Manual
M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. page 22 / 25

SERVICING
Maintenance
The correctly operated mechanical seal needs low maintenance. Wear parts,
however, have to be replaced, if necessary.

A duly operation includes a regular check of the following parameters:


 Temperature
 Leakage (drainage) of the mechanical seal

An inspection of the mechanical seal should be carried out along with a revision of
the complete plant. We recommend having this inspection be performed by
EagleBurgmann.

If the mechanical seal is removed during a revision of the plant the sliding faces
should be refinished at the manufacturer and both, elastomeric seal rings and springs
should be replaced.

Directives in case of failure

Try to define the kind of failure and record it.

 In the event of excessive leakage changes in the leakage amount must be


monitored. If necessary the machine has to be switched off.
 If a constant amount is leaking in a steady flow the mechanical seal is damaged.
 In the event of an inadmissible temperature rise the machine has to be stopped
for safety reasons.

If there is a malfunction which you cannot correct on your own, or if the cause of
malfunction is not clearly recognisable please immediately contact the nearest
EagleBurgmann agency, an EagleBurgmann service centre or the EagleBurgmann
headquarters.

During the warranty period the mechanical seal must only be disassembled with
approval of the manufacturer or when a representative is present.

After-sales service by EagleBurgmann

EagleBurgmann's customer service department offers a comprehensive service


package covering consultancy, engineering, standardisation, installation,
commissioning as well as damage analysis right through to seminars on sealing
technology.

Addresses are listed in various EagleBurgmann brochures as well as under


www.eagleburgmann.com.

en M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. / July 7, 2016 Rev. 14


Operating Manual
M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. page 23 / 25

Reconditioning (repair)

If reconditioning is necessary, the complete seal should be sent to the


manufacturer, as this is the best way to find out which components can be
reconditioned or which parts must be replaced in order to ensure an optimum
tightness.

If, for compelling reasons, a reconditioning has to be carried out on site (e.g. no.
spare seal on stock, long transport, problems with customs) the seal may be repaired
in a clean room by trained personnel of the user under the direction of
EagleBurgmann mechanics.

Disassembly / removal

 Stop the machine as instructed, allow to cool, depressurise it and


ensure that pressure cannot build up again!
 Work on the M.S. is only permitted when the machine is at a
standstill and depressurised.
 Depressurise and shut off (or drain) the supply of the M.S.
 There must be no product in the M.S.  if necessary drain the
machine and rinse it out!
 Isolate the machine to prevent it starting up unexpectedly!
 Observe the safety notes (safety data sheets)!

IMPORTANT! When removing, please observe by all means:


 current accident prevention regulations
 regulations for handling hazardous substances

WARNING! Seals that have been used with hazardous substances must be properly
cleaned so that there is no possible danger to people or to the environment.

IMPORTANT! The packaging used to transport the seal must


 be identified with the relevant hazard symbol and
 include the safety data sheet for the product and/or supply medium.

IMPORTANT! If the medium to be sealed builds deposits or tends to solidify during


cooling down or standstill of the machine the stuffing box has to be flushed with
suitable clean liquid. The flow rate and the liquid should be determined by the user
considering the chemical resistance of the seal materials.

The order of disassembly to remove the mechanical seal out of the machine depends
on the design of the machine and should be determined by the machine
manufacturer.
 If the machine manufacturer specified auxiliaries (jigs and fixtures) they have to be
used in accordance with the specifications of the manufacturer.

en M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. / July 7, 2016 Rev. 14


Operating Manual
M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. page 24 / 25

 Remove the supply piping to the mechanical seal. Collect drained liquid and
dispose of properly.

 Drain the mechanical seal. Collect the drained liquid and dispose of properly.

 Unscrew the set screws with cup point and dispose of.
ATTENTION! Set screws with cup point must be used only once. Repeated fastening
endangers the safety of force transmission.

 Remove the mechanical seal in the reverse sequence as described for assembly
(set up).

ATTENTION! Sealing elements made of PTFE have to be used only once.

Spare parts

 Only EagleBurgmann original spare parts must be used. Otherwise


 Risks of a failure of the mechanical seal, endangering persons and environment.
 The EagleBurgmann guarantee for the seal lapses.
 For a quick exchange a complete spare seal should be on stock.

Required details for enquiries and orders


For enquiries and orders the following details are required:
 EagleBurgmann commission no.
 Drawing no. of mechanical seal
 Part item no., designation, material, number of pieces acc. to drawing.

Address of headquarters:
EagleBurgmann Germany GmbH & Co. KG
Postfach 1240
D - 82515 Wolfratshausen
Germany
 +49 (0) 81 71-23 0
Fax +49 (0) 81 71-23 12 14
www.eagleburgmann.com

en M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. / July 7, 2016 Rev. 14


Operating Manual
M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. page 25 / 25

Disposal of the mechanical seal

Usually, the mechanical seals can be easily disposed of after a thorough cleaning.
 Metal parts (steels, stainless steels, non-ferrous heavy metals) divided into the
different groups and sent to scrap metal waste.
 Ceramic sliding materials (synthetic carbons, ceramics, carbides) belong to waste
products. They can be separated from their housing materials, as are
physiologically recognised as safe.
 Synthetic materials/plastics (elastomers, PTFE) belong to special waste.
CAUTION! Material containing fluorine must not be burnt.
IMPORTANT! Some of the synthetic materials, divided into the different groups can be
recycled.

Copyright

EagleBurgmann Germany GmbH & Co. KG (Germany) holds the copyright to this
document. Customers and operators of mechanical seals are free to use this
document in the preparation of their own documentation. No claims of any type or
form can be derived in such instance.

July 07, 2016


Technical Documentation Department

en M7../dw.. / (HS)M7(N)../dw../LASERTEC-M7N/dw../M7S../dw.. / July 7, 2016 Rev. 14

You might also like