EN

MC1
USER / INSTALLER MANUAL

FUSE 5x20

T.PAUSA
T.MOT.PED
T.MOT
PGM.AUT
LAMP/CORT
IN.CMD.AP.
CODE PED
CODE

FUSE 5x20
SEL SET

V1.3
REV. 08/2019
 00. CONTENT 01. SAFETY INSTRUCTIONS
INDEX ATTENTION:

01. SAFETY INSTRUCTIONS 1B This product is certified in accordance with European

02. THE CONTROL BOARD Community (EC) safety standards.
CONNECTIONS SCHEME 4
TECHNICAL CHARACTERISTICS 5A
This product complies with Directive 2011/65/EU of
CONNECTORS DESCRIPTION 5A
the European Parliament and of the Council, of 8 June
PROGRAMMING PRE-RECOMENDATIONS 5B 2011, on the restriction of the use of certain hazardous
SEL/SET BUTTONS 6A substances in electrical and electronic equipment.
MOTOR'S STRENGH AND SPEED 6A
FUSES
(Applicable in countries with recycling systems).
6A
LEDS This marking on the product or literature indicates that
6B
the product and electronic accessories (eg. Charger, USB
03. INSTALLATION
CONDITIONS AND PRE VERIFICATIONS
cable, electronic material, controls, etc.) should not be
7A
ESSENTIAL INSTALLATION STEPS 7A
disposed of as other household waste at the end of its
CONTROL BOARD INSTALLATION 7B
useful life. To avoid possible harm to the environment or
04. PROGRAMMING
human health resulting from the uncontrolled disposal
PRE-INSTALLATION WARNINGS 8A
of waste, separate these items from other types of waste
MAIN MENU 9A and recycle them responsibly to promote the sustainable
EXTENDED MENU 1 12B reuse of material resources. Home users should contact
EXTENDED MENU 2 14B the dealer where they purchased this product or the
OTHER INFORMATION 15 National Environment Agency for details on where and
05. MAINTENANCE how they can take these items for environmentally safe
PARAMETERS TO TAKE CARE 15B recycling. Business users should contact their vendor
06. TROUBLESHOOTING and check the terms and conditions of the purchase
COMPONENTS TEST 16A agreement. This product and its electronic accessories
PHOTOCELLS AND TRANSMITTER TESTS 16B should not be mixed with other commercial waste.
INSTRUCTIONS FOR FINAL CONSUMERS 17
INSTRUCTIONS FOR SPECIALIZED INSTALLERS 17
This marking indicates that the product and electronic
accessories (eg. charger, USB cable, electronic material,
controls, etc.) are susceptible to electric shock by direct
or indirect contact with electricity. Be cautious when
handling the product and observe all safety procedures
in this manual.
1A 1B
EN EN
 01. SAFETY INSTRUCTIONS
GENERAL WARNINGS terms of usage of the product in a safe manner and who understands
• This manual contains very important safety and usage information. the risks and dangers involved.
very important. Read all instructions carefully before beginning the • Children shouldn’t play with the product or opening devices to avoid
installation/usage procedures and keep this manual in a safe place the motorized door or gate from being triggered involuntarily.
that it can be consulted whenever necessary.
• This product is intended for use only as described in this manual. Any WARNINGS FOR TECHNICIANS
other enforcement or operation that is not mentioned is expressly • Before beginning the installation procedures, make sure that you
prohibited, as it may damage the product and put people at risk have all the devices and materials necessary to complete the
causing serious injuries. installation of the product.
• This manual is intended firstly for specialized technicians, and does • You should note your Protection Index (IP) and operating temperature
not invalidate the user’s responsibility to read the “User Norms” to ensure that is suitable for the installation site.
section in order to ensure the correct functioning of the product. • Provide the manual of the product to the user and let them know
• The installation and repair of this product may be done by qualified how to handle it in an emergency.
and specialized technicians, to assure every procedure are carried • If the automatism is installed on a gate with a pedestrian door, a door
out in accordance with applicable rules and norms. Nonprofessional locking mechanism must be installed while the gate is in motion.
and inexperienced users are expressly prohibited of taking any • Do not install the product “upside down” or supported by elements
action, unless explicitly requested by specialized technicians to do do not support its weight. If necessary, add brackets at strategic
so. points to ensure the safety of the automatism.
• Installations must be frequently inspected for unbalance and the • Do not install the product in explosive site.
wear signals of the cables, springs, hinges, wheels, supports and • Safety devices must protect the possible crushing, cutting, transport
other mechanical assembly parts. and danger areas of the motorized door or gate.
• Do not use the product if it is necessary repair or adjustment is • Verify that the elements to be automated (gates, door, windows,
required. blinds, etc.) are in perfect function, aligned and level. Also verify if
• When performing maintenance, cleaning and replacement of parts, the necessary mechanical stops are in the appropriate places.
the product must be disconnected from power supply. Also including • The central must be installed on a safe place of any fluid (rain,
any operation that requires opening the product cover. moisture, etc.), dust and pests.
• The use, cleaning and maintenance of this product may be carried • You must route the various electrical cables through protective
out by any persons aged eight years old and over and persons whose tubes, to protect them against mechanical exertions, essentially on
physical, sensorial or mental capacities are lower, or by persons the power supply cable. Please note that all the cables must enter
without any knowledge of the product, provided that these are the central from the bottom.
supervision and instructions given by persons with experienced in • If the automatism is to be installed at a height of more than 2,5m

2
EN
 01. SAFETY INSTRUCTIONS
from the ground or other level of access, the minimum safety and • Do not perform any operation on mechanical elements or hinges if
health requirements for the use of work equipment workers at the the product is in motion.
work of Directive 2009/104/CE of European Parliament and of the
Council of 16 September 2009.
• Attach the permanent label for the manual release as close as RESPONSABILITY
possible to the release mechanism. • Supplier disclaims any liability if:
• Disconnect means, such as a switch or circuit breaker on the electrical • Product failure or deformation result from improper installation
panel, must be provided on the product’s fixed power supply leads use or maintenance!
in accordance with the installation rules. • Safety norms are not followed in the installation, use and
• If the product to be installed requires power supply of 230Vac or maintenance of the product.
110Vac, ensure that connection is to an electrical panel with ground • Instructions in this manual are not followed.
connection. • Damaged is caused by unauthorized modifications
• The product is only powered by low voltage satefy with central (only • In these cases, the warranty is voided.
at 24V motors)

WARNINGS FOR USERS

• Keep this manual in a safe place to be consulted whenever necessary.
• If the product has contact with fluids without being prepared, it
must immediately disconnect from the power supply to avoid short
circuits, and consult a specialized technician.
• Ensure that technician has provided you the product manual and
informed you how to handle the product in an emergency.
• If the system requires any repair or modification, unlock the
automatism, turn off the power and do not use it until all safety SYMBOLS LEGEND:
conditions have been met.
• In the event of tripping of circuits breakers of fuse failure, locate • Important safety • Potentiometer
the malfunction and solve it before resetting the circuit breaker or notices information
replacing the fuse. If the malfunction is not repairable by consult • Useful information • Connectors
this manual, contact a technician. information
• Keep the operation area of the motorized gate free while the gate in • Programming • Buttons
in motion, and do not create strength to the gate movement. information information

3
EN
 gate.
F2
CONNECTION SCHEME

TRANSFORMER
110V OR 230V

VR1
02. THE CONTROL BOARD

T.PAUSA
T.MOT.PED
T.MOT
PGM.AUT
LAMP/CORT
IN.CMD.AP.
F1 CODE PED
CODE

SEL SET
radio, developed for the automations control for sliding gates or just 1 motor for swing
The MC1 is an electronic single phase control board with control system via built-in

CN1
CN2

L N LAMP MOTORE
24V PUL DS FAP FCH ANTENNA
ANTENNA
230~ 230~ AP COM CH
1 2 3 4 5 6 7 1 2 3 4 5 6 7 8 9 10

LIMIT-SWITCHES
or
NEUTRAL 110V

PHASE 230V
OPEN
CLOSE

FLASHLIGHT

KEY SELECTOR / PUSH BUTTON

(or)

MOTOR
PHOTOCELLS

DV 12/24V DV 12/24V COM NC

~~ ~~

CAPACITOR

ATTENTION:
The control board power supply depends on the value described in the
EN

transformer!
4
 02. THE CONTROL BOARD 02. THE CONTROL BOARD
TECHNICAL CHARACTERISTICS TECHNICAL CHARACTERISTICS

• Power Supply 110V or 230V AC | 50-60Hz | 900W max. (4A) • PROGRAMMING PRE-RECOMENDATIONS
110V/230V AC 500W max. Before proceeding to the control board configuration, note the following points listed
• Lightbulb or courtesy light output 100W (max. resistive cargo) in the table below to better understand the control board's functions:
50W (max. induced cargo)
• Motor’s output 110V/230V AC 50/60Hz 750W max. Flashing / Courtesy light:

CN1
03 and 04 • This output allows connection of a 110V / 230V courtesy light or a
• Output for powering accessories 24V AC 3W max.
flashing light (see page 3). This output does not flash.
• Working temperature -20°C to +55°C
Step by step pushbutton:
• Incorporated Radio Receiver 433,92 Mhz 03 and 04• This input (NO) allows to control the control board through
• Code types 12-18 bits or Rolling Code pushbuttons. When you receive the first order, it triggers the opening until the
motor's working time ends or until it detects the opening limit switch.
• Maximum memory capacity 120 codes (CODE or CODE PED)

CN2
When it receives a second order, it triggers the closing.
• Control board dimensions 108x138 mm If you receive an order during the opening or closing of the gate, the movement
stops and it's only restored (in the opposite direction from what it was before it
stops) after receiving a new order. During opening, if it receives a order to stop
(active T.PAUSA), it will temporize and close the gate.
• CONNECTOR’S DESCRIPTION TIMER functioning:
03 and 04 • The control board allows a connection of a TIMER. With this

CN2CN2
01 • 110V/230V Line Input (PHASE) device, you can set an exact time for the gate to perform the opening / closing
02 • 110V/230V Line Input (NEUTRAL) automatically. For example: If you program a time between 8 am and 10 am,
03 • Lightbulb / Courtesy light’s output (GND/COM) this will cause an opening contact at 8 am and will maintain the contact until
04 • Lightbulb / Courtesy light’s output (phase) 10am. At 10am, the gate will perform the closing, after waiting the pause time.
05 • Motor’s Output (opening) (It is important to enable automatic closure)
CN1

06 • Motor’s Output (GND/COM)

07 • Motor’s Output (closing) Safety circuits:
ATTENTION 05 • This circuit allows photocells connection.

CN2
CN2
03 to 07 output:
This device operates only in the gate closure, and when triggered, reverses the
The output voltage depends on the supply voltage (01 and 02) direction gate movement.

01 • Output for powering photocells (24V AC - 6W Max.) Limit-switches:

02 • Output for powering photocells (GND/COM) 06 to 08 • The control board needs the connection limit switches in opening
03 • Step-by-step pushbutton input (NO) and closing (both NC). The trigger of any one of the limit switches causes the
04 • GND/COM output immediate stop of the gate's movement.The limit switches triggering is signaled
05 • Security devices input (NC) by the LEDs FCH and FAP. When a limit switch is activated,the respective LED
CN2
CN2

06 • Opening limit-switch input (NC) goes off. The LED FAP corresponds to opening limit switch and the LED FCH to
07 • GND/COM output the closing limit switch.
08 • Closing limit-switch input (NC) If you do not use limit switches (swing gate) should close with a shunt circuits
09 • Antenna input (mass) 6-7 and/or 7-8 of the CN2 connector. It is mandatory the use of limit switches
10 • Antenna input (hot pole) on sliding gate motors!

5A 5B
EN EN
 T.PAUSA
T.MOT.PED
02. THE CONTROL BOARD 02. THE CONTROL BOARD T.MOT
PGM.AUT
LAMP/CORT
TECHNICAL SPECIFICATIONS TECHNICAL SPECIFICATIONS IN.CMD.AP.
CODE PED
CODE
• SEL/SET BUTTONS • LEDS

FUSE 5x20
There are LEDs in the control board to inform the installer about connection status of
SEL key:
To select the function to change. This selection is identified by the
SEL SET
the various components. Before the central configuration, note the behavior of these
LEDs, which must match those described in the table below.
intermittency of LED corresponding to the selected function at that time.
Pressing the SEL key repeatedly will cycle through the various functions
SEL to be programmed. The selection remains active for 10 seconds, and
after that time the control board returns to the original state (no active PUL DS FAP FCH
selection).

SET key:
To program the selected function with the SEL key.
SET This LED signals the connection of accessories which control automatism
The SET key can be replaced by transmitter key, as long it finds itself functioning like key selectors or push buttons. It lights up when it receives
programmed. accessories signals (contact changes from NO to NC). If you need to connect
PUL
several components in this entry, they must be connected in parallel mode
(direct connection on connector).
• MOTOR'S FORCE AND SPEED
The LED signals the connection of safety devices such as photocells or safety
VR1 potentiometer: edge (required to MR12 connection). This LED is lit when a device is connected
The control board has a "VR1" potentiometer to adjust the force and at the DS input (NC). Whenever the contact safety device is interrupted (NO |
speed of the motors, controlled by the microprocessor. Adjustment can be DS
eg object between photocells), the LED turns off.
made between 50% and 100% force / speed. If you need to connect multiple components on this input, they must be
In each starting movement, the control board applies the maximum force connected in series mode.
VR1 for 2 seconds, even when a force adjustment is made to a value other
than the maximum. LED signals the connection of the opening limit switch. This LED stays lit as
FAP soon as the opening limit switch is connected into the terminal 6 of CN2 (NC).
When you adjust the VR1 potentiometer, it is necessary to redo the programming Whenever the opening limit switch is activated (NO), the LED will turn off.
course, because the maneuver and slowdown times may vary.
LED signals the connection of the closing limit switch. This LED stays lit as
FCH soon as the closing limit switch is connected into the terminal 6 of CN2 (NC).
Whenever the closing limit switch is activated (NO), the LED will turn off.
• FUSES
There are two fuses that protect the center against electrical overloads. These protection
devices are an essential part of the power distribution system as they prevent damage
to other circuit elements.

F1 T6.3AL250V - 3A 250V

F2 50mAL250V - 50mA 250V

FCH

6A 6B
EN EN
 03. INSTALLATION 03. INSTALLATION
INSTALLATION ESSENTIAL GUIDE CONTROL BOARD INSTALLATION

• CONDITIONS AND PRE VERIFICATIONS

• Make sure that the motor is properly installed at the gate.
• Check if the ambient temperature values are acceptable for the functioning of this
control board.
• Perform the entire installation with the power off.
• Consult the manufacturer's instructions from all the components to install.
• Always make a ground connection directly to the motor's metal structure.

• ESSENTIAL INSTALLATION STEPS

• Place the control board in the appropriate fixing location and tighten the screws to
secure it.
• Make the connections of all the accessories and components you want to use, according
to the wiring diagram (p. 4).
• Connect the control board to a 110V or 230V power supply according to the value
shown on the transformer (terminals 1 and 2 - CN1).
• Check that the limit switches are working properly. (P. 8A)
• Also check other devices like selectors or photocells. (P. 8B)
• Start by programming a transmitter (p. 9A).
• Now do an course's automatic programming (p. 10B).
• If necessary, you can now adjust the strength / speed of the automatism in the VR1
potentiometer (p. 6A). Whenever any change is made in this potentiometer, you must
redo the course's automatic programming.
• Put silicone or another type of sealing in the cable entries of the control board box in
order to prevent the entrance of insects or other elements that may damage the control
board.

At this time, the control board is programmed with all the essential
functions for a proper functioning of the automation. If you want to enable
other control board functions, please check how to do so, on the following
pages.

7A 7B
EN EN
 04. PROGRAMMING 04. PROGRAMMING
PRE-INSTALLATION WARNINGS PRE-INSTALLATION WARNINGS

After installing the control board and connecting the wires, you must ensure that all • PHOTOCELLS TEST
connected components are working properly. To do this, follow these steps: The photocells are a safety device that inform the control board that an object is
obstructing the gate's route. They send a signal to prevent the gate from damaging the
object.
• LIMIT SWITCHES TEST
The photocells are connected to the control board DS input (see wire connection
First, you must define whether the operator is installed on the right or left of the gate.
page). This input has an assigned LED that informs about the connection status of the
This information will indicate which side is the opening and closing.

To test the connection of photocells in the control

board, just interrupt the signal between the two
photocells putting his hand in front of one of them.
LEFT RIGHT A sound similar to a "click" indicates that the signal
INSTALLATION INSTALLATION was interrupted and the LED DS should be off while
the photocells are interrupted. If it does not operate
on this way, there is a problem in the connection
between the photocells and the control board.

This test will be exemplified with the automation installed on the right.
Lean the automatism limit switch spring to the right until you hear a "click". The FAP LED • KEY SELECTOR TEST
must turn off! Now Lean the automatism limit switch spring to the left until you hear a Components as key selector or push buttons are used to control the functioning of
"click". The FCH LED must turn off! the gate. These components are connected to the control board PUL input (see wiring
If the LEDs turn off oppositely, reverse the wires to the terminals 6 and 8 of CN2. diagram on page 4). This input has an LED assigned that informs the connection status
of the connected components. This LED remains off when a component is connected
(NO mode).

To test the key selector connection in the control

board, simply turn the key to one of the directions.
Close Open At this time, the PUL LED lights up (NC), and turns off
when the key go back to the original position (NO). If
it does not operate on this way, there is a problem in
the connection between the device and the control
board.

The limit switches are an important safety system of the motor. It is extremely
important that they are properly connected in the control board, otherwise it
may cause serious damage or injury.

8A 8B
EN EN
 04. PROGRAMMING 04. PROGRAMMING
MAIN MENU MAIN MENU

Delete allT.MT.POconfigured
USA
The control unit is supplied by the manufacturer with the ability to select some main A D
T.PE OT
.M
transmitters: USA
T.PA ED
T OT.P T
functions directly.
T
.AU T.M T.MO
PGM/CORT
P P.
LAM .CMD.A ED
01 • Press the SEL key .AU
PGM/CORT
T
02 • Press the SEL key
P.
once, and the CODE
P
IN DE P E
CO COD LAM .CMD.A ED
for 10 seconds! The
MAIN MENU LED begins to flash.
IN DE P E
CO COD
CODE LED turns off
LED LED OFF LED ON SET and all transmitters
SET
SEL have been deleted.
• CODE No programmed code Programmed (s) code (s) SEL

• CODE PED. No programmed code Programmed (s) code (s)

You can not delete only one specific transmitter!
• IN.CMD.AP CMD Opening Inhibition OFF CMD Opening Inhibition ON
• LAMP/CORT Flashing light mode Courtesy Light Mode
• CODE PED | PEDESTRIAN FUNCTIONING
• PGM. AUT. Automatic Programming OFF Automatic Programming ON
The control board allows you to program the gate to open just enough for the passage of
• T. MOT. Working Time = 30 sec Prog. time automatically people without making a full opening. The CODE PED function allows to program a code
to command only this type of opening.
• T. MOT. PED Pedestrian Working Time = 10 sec Prog. time automatically
It is advised to do the programming of T.MOT.PED function to set the distance that the
• T. PAUSA Automatic Closing OFF Automatic Closing ON door should open, otherwise the control board will open a pre-set distance.
The control board is supplied by the manufacturer with this function disabled.
USA
Programming transmitters
T.PA ED
for pedestrian mode:
• CODE | PROGRAMMING TRANSMITTERS OT.P T
T.M T.MO
.AU
T
PGM/CORT
P P.
LAM .CMD.A ED
This function allows you to program new transmitters to control the automatism. IN DE P E
CO COD USA
T.PA ED
The control board only accepts Dip-Switch code transmitters or Rolling Code MOTORLINE, T.P
T.MO T.MOT
.AUT
and has a maximum capacity of 120 codes. SET PGMCORT
P/
LAM MD.AP.
When trying to program the 121st code, all the programming LEDs blink a few times SEL IN.C E PED
COD CODE
simultaneously signaling that the memory is full.
01 • Press SEL key 02 • Press once the 03 • The CODE PED LED
Programming new
T.PA Etransmitters:
US A

twice, and the CODE SET

D
.MO
T.P OT
T T.M T transmitter's key you remains permanently
.AU
PGM/CORT
. PED LED begins to want to program, for S E L
lit, signaling the
M P .AP
L A MD D
IN.C DE PE E
CO COD USA
T.PA ED flash. 1 sec. program's success.
T.P
T.MO T.MOT
.AUT
SET PGMCORT
P/
LAM MD.AP. Delete all configured transmitters for pedestrian opening:
SEL IN.C E PED
COD CODE 01. Press the SEL key twice until the LED CODE PED begins to flash.
02. Press the SET key for 10 seconds and all the codes from this function are deleted.
01 • Press the SEL key 02 • Press once the 03 • The CODE LED
once, and the CODE transmitter's key you SET
remains permanently
LED begins to flash. want to program, for lit, L
SEsignaling the It is not possible to erase just one transmitter.
1 sec. program's success. Attention: The "pedestrian passage" option occupies 1 slot of 120 available in the
control board's memory. In other words, if you program, in the same transmitter,
the CODE and CODE PED, you can still program 118 transmitters.

9A 9B
EN EN
 04. PROGRAMMING 04. PROGRAMMING
MAIN MENU MAIN MENU

• INB. CMD. AP | TRANSMITTER INHIBITION DURING THE OPENING AND PAUSE TIME • PGM. AUT. | COURSE AUTOMATIC PROGRAMMING
With the function activated, the control board rejects all the transmitters and devices With the limit switches already set, the control board allows automatic programming of
signals during the opening maneuvers and automatic pause time. the working time (recommended).
The control board is supplied by the manufacturer with this function deactivated. Enable automatic programming:
Activate (LED
T.PA ED ON) / deactivate (LED OFF) function:
US A

OT.P OT USA
T.M T.M T.PA D E
.AU
T OT.P T
T.M T.MO
PGM/CORT
P P.
LAM .CMD.A ED
01 • Press the SEL .AU
PGM/CORT
T
02 • Press SET button
P P.
IN DE P E
CO COD button the times LAM .CMD.A ED
IN DE P E to enable / disable
CO COD
necessary until the the function.
SET INB CMD AP LED
SET
SEL starts to flash.
SEL USA
T.PA ED 01 • Unlock the motor, put the gate halfway and lock the motor.
OT.P T USA
T.M T.MO T.PA D E
.AU
T OT.P T
T.M T.MO
PGM/CORT
P P.
LAM .CMD.A ED
02 • Press the SEL .AU
PGM/CORT
T
03 • Press and hold
P.
SET and the door
P
IN DE P E
CO COD button the times LAM .CMD.A ED
IN DE P E

• LAMP/CORT | FLASHING LIGHT / COURTESY LIGHT SELECTION necessary until the

CO COD
must begin to close!
SET PGM AUT LED starts
The control board has a 110V / 230V AC output for connection of a flashing light or SET
SEL to flash.
courtesy light at terminals 3 and 4 of CN1. This output does not flash. Observe the three SEL
possible behaviors:

OPTIONS BEHAVIOR If the gate start to open, release the SET button, reverse the wires of links 5 and
7 of CN1, and start this program from the beginning.
Opening Pause Time Closing 3min. After Closing USA
T.PA ED
1 OT.P T
T.M T.MO
.AU
T
04 • Allow the gate 05 • When closing the
PGM/CORT
(factory) P P.
LAM .CMD.A ED
IN DE P E to close, open and USA
T.PA ED 2nd time, the PGM
T.P
Opening Pause Time Closing 3min. After Closing CO COD
close again without T.MO T.MOT AUTO LED will be lit
2 releasing the SET
.AUT
PGMCORT and the programming
P/
SET LAM MD.AP.
button! IN.C E PED has been successfully
SEL COD CODE
Opening Pause Time Closing 3min. After Closing completed.
3
Automatic slowdown: SET
Enable OPTION 1: SEL
With the LED lit, press SEL 4 or 5 times, and when the LED flashes (normally or quickly)
Closure
press the SET button and the LED turns off.
15%
slowdown 85%
Enable OPTION 2: Normal speed 15%
With the LED LAMP / CORT off, press 4 times the SEL key until this LED blinks normally. Aperture slowdown
Press the SET button and the LED lights permanently.

Enable OPTION 3:
With the LED LAMP / CORT off, press 5 times the SEL key until this LED flashes quickly! The control board automatically sets a slowdown in opening and closing equal to
Press the SET button and the LED lights permanently. 15% of the total course.

10A 10B
EN EN
 04. PROGRAMMING 04. PROGRAMMING
MAIN MENU MAIN MENU

• T.MOT AND SLOWDOWN | PROGRAMMING MOTOR TIME AND RELAXATION (MANUALLY) • T. MOT. PED | PROGRAMMING PEDESTRIAN WORKING TIME
This function allows you to manually program the distance that the gate opens to
Unlike PGM.AUT, this function allows the programming of motor's time and slowdown pedestrian crossing. The control board is supplied by the manufacturer with a pedestrian
manually. Use it whenever PGM.AUT does not meet your needs. If you set the course working time set at 10 seconds without slowdown.
using this function after doing an automatic programming, the control board will forget
the automatic programming and assumes the programmed course manually. Instead of using the control board's SET button during programming, you can use
the CODE key of an already programmed transmitter.
Programming
T.PA ED pedestrian working time with slowdown (closed gate):
U SA
Instead of using the central's SET button during programming, you can use the key T.M
OT.P OT
T.M T
USA
T.PA ED
OT.P T
of a remote control that is already programmed. .AU
PGM/CORT
P P. 01 • Press SEL button
T.M T.MO
.AU
PGM/CORT
T
02 • Press SET button
LAM .CMD.A ED
P P.
USA
Programming motor's working time and slowdown (closed gate):
T.PA ED USA
IN DE P E
CO COD the times necessary LAM .CMD.A ED
IN DE P E for 1 second, so that
OT.P T T.PA ED CO COD
T.M T.MO
.AU
T OT.P T
T.M T.MO until the T.MOT. LED the motor starts the
PGM/CORT
P P.
LAM .CMD.A ED
01 • Press SEL button .AU
PGM/CORT
T
02 • Press SET button SET starts to flash. opening.
P P.
the times necessary for 1 second, so that SET
IN DE P E LAM .CMD.A ED
CO COD IN DE P E
CO COD SEL
until the T.MOT. LED the motor starts the SEL
SET starts to flash. opening.
SET
SEL
SEL If the motor starts to close, invert the terminal cables 5 and 7 of the CN1 connector.
USA USA
T.PA ED T.PA ED
OT.P T OT.P T
T.M T.MO T.M T.MO
.AU
T
03 • Press SET button .AU
T
04 • Press again SET
If the motor starts to close, invert the terminal cables 5 and 7 of the CN1 connector. PGM/CORT
P P.
PGM/CORT
P P.
USA
T.PA ED
USA
T.PA ED
LAM .CMD.A ED
IN DE P E for 1 second, so that LAM .CMD.A ED
IN DE P E when you want to
OT.P T OT.P T CO COD CO COD
T.M T.MO T.M T.MO
.AU
PGM/CORT
T
03 • Press SET button .AU
PGM/CORT
T
04 • Press again SET the motor starts the set the end of the
P P.
LAM .CMD.A ED
for 1 second, so that
P P.
LAM .CMD.A ED
when you reach the slowdown. pedestrian opening.
IN DE P E
CO COD
IN DE P E
CO COD SET SET
the motor starts the opening limit switch. SEL SEL
slowdown.
SET SET

SEL SEL The LED T.MOT.PED. will flash quickly indicating that the control board started
programming
.PA
USA
the pedestrian closing maneuver and.PA
the automation starts to close.
USA
T ED T ED
The LED. T. MOT. will flash quickly indicating that the control board started programming OT.P T
T.M T.MO
OT.P T
T.M T.MO
M .AU
P /CORT
T
05 • Press SET button M .AU
P /CORT
T
06 • Press again SET
the closing maneuver and the automation starts to.PAUclose.
G G
P P. P P.
.PA
USA
T ED
SA
T ED
LAM .CMD.A ED
IN DE P E for 1 second, so that LAM .CMD.A ED
IN DE P E when you reach the
OT.P T OT.P T CO COD CO COD
T.M T.MO T.M T.MO
.AU
PGM/CORT
T
05 • Press SET button .AU
PGM/CORT
T
06 • Press again SET the motor starts the closing limit switch.
P P.
LAM .CMD.A ED
for 1 second, so that
P P.
LAM .CMD.A ED
when you reach the slowdown during
IN DE P E
CO COD
IN DE P E
CO COD SET SET
the motor starts the closing limit switch. closing.
SEL SEL
slowdown during
SET SET
closing.
SEL SEL Programming pedestrian motor's working time without slowdown (closed gate):
Programming motor's working time without slowdown (closed gate): To make a program without slowdown, press TWICE the SET button when you want to set
the opening's end.
To make the programming without slowdown, leave the gate reach the opening limit
T. MOT.PED LED will flash quickly and the motor starts the closing maneuver.
switch and press TWICE (quickly) the SET button.
When the gate reaches the closing limit switch, click SET twice again to finish programming.
The LED T. MOT. will flash quickly and the motor starts the closing maneuver.
When the gate reaches the closing limit switch again, click SET twice to finish programming.

11A 11B
EN EN
 04. PROGRAMMING 04. PROGRAMMING
MAIN MENU EXTENDED MENU 1

• T. PAUSA | PROGRAMMING PAUSE TIME FOR AUTOMATIC CLOSING (MAX 4 MIN) The control board is supplied with extra functions that can be activated through the
This function allows you to set the time that the gate remains open after the end of the extensed menu 1.
opening maneuver. After this time, the control board automatically initiates the closing.
The control board is supplied by the manufacturer without automatic closure. EXTENDED MENU 1
LED LED OFF LED ON
Activate or
T.PA change the pause Utime for automatic closure:
U SA
ED SA USA
OT.P T T.PA ED T.PA ED
T.M .MO
OT.P T OT.P T
• CODE Step by Step Mode Automatic mode
T T
.AU T.M T.MO T.M T.MO
PGM/CORT .AU
T
.AU
T
P P.
LAM .CMD.A ED PGM/CORT PGM/CORT
P P. P P.
IN DE P E LAM .CMD.A ED USA LAM .CMD.A ED
CO COD IN DE P E
CO COD
T.PA ED
T.P
IN DE P E
CO COD
• CODE PED. Electric brake = OFF Electric brake = ON
T.MO T.MOT
.AUT • IN.CMD.AP Present Man = OFF Pres. APCH or CH = ON
SET PGMCORT
P/
SET LAM MD.AP. SET
SEL IN.C E PED
SEL COD CODE SEL
• LAMP/CORT Slowdown = OFF Slowdown = ON
• PGM. AUT. Follow Me = OFF Follow Me = ON
01 • Press SEL button 02 • Press SET button. 03 • Wait the desired 04 • Press SET button.
the times necessary The T.PAUSA LED SET time. T. PAUSA LED stays lit
time for pause • T. MOT. PGM at distance = OFF PGM at distance = ON
SEL30 seconds)
until the T.PAUSA LED starts to flash quickly. (Eg and the pause time
starts to flash. is set. • T. MOT. PED Alternated flashing signal with LED T. PAUSA
• T. PAUSA Alternated flashing signal with LED T. MOT. PED

Disable the
T.PA Eautomatic
USA
D
OT.P T
closing: USA
T.M T.MO T.PA ED
OT.P T
• EXTENDED MENU 1 ACCESS
T
.AU T.M T.MO
PGM/CORT
P P.
LAM .CMD.A ED
01 • Press SEL button .AU
PGM/CORT
T
02 • Double-press
P P.
IN DE P E
CO COD the times necessary LAM .CMD.A ED
the SET button within
To access USA the Extended Menu 1 functions, follow these instructions:
IN DE P E
CO COD
until the T.PAUSA LED 2 sec! The T.PAUSA T.PA D E
OT.P T
SET starts to flash. LED turns off and T.M T.MO
.AU
T
01 • Continuously 02 • The T.MOT.
SET PGM/CORT
SEL the function stays P P.
LAM .CMD.A ED
IN DE P E press the SET button USA
T.PA ED PED and T.PAUSA
SEL CO COD T.P
disabled. for 5 seconds. T.MO T.MOT LEDs start to flash
.AUT
PGMCORT alternately.
P/
SET LAM MD.AP.
IN.C E PED
SEL COD CODE

After entering the Extended Menu 1, you have 30 Sseconds

ET to select any function
SEL After 30 seconds without pressing any
of this menu (using the SEL and SET keys).
button, the control board returns to the main menu.

12A 12B
EN EN
 04. PROGRAMMING 04. PROGRAMMING
EXTENDED MENU 1 EXTENDED MENU 1

• CODE | STEP BY STEP / AUTOMATIC FUNCTIONING • INB. CMD. AP | PRESENT MAN FUNCTIONING
Automatic Mode Functioning (LED CODE ON): When this function is active, the control board only opens / closes the automatism while
• The first impulse transmitter/pushbutton triggers the opening of the gate. the key of the transmitter / push button is pressed.
• The second impulse (after gate fully opens) triggers the closing of the gate. If it is released, the automatism stops immediately.
• If you press the transmitter key during opening or closing maneuver, the gate inverts The control board is supplied by the manufacturer with this function disabled.
the direction of the operation until it reaches the limit switch.
Enable (LED ON) / Disable (LED OFF) function:
Step by Step Mode Functioning (LED CODE ON): SA
01 • Enter.MT.Pthe E Extended Menu 1 (see "EXTENDED MENU
AU D
OT.P OT USA 1 ACCESS" on page 11B).
For each order you send from a remote control / push button, the control board will T T.M T
.AU
T.PA ED
OT.P T
T.M T.MO

have a behave like: open-stop-close-stop-open - (...). The control board is supplied by L

PGM/CORT
A M P .AP
MD D
. 02 • Press SEL button .AU
PGM/CORT
T
03 • Press once SET
IN.C DE PE E P P.

the manufacturer with the step by step active. CO COD the times necessary LAM .CMD.A ED
IN DE P E button to activate
CO COD
until the INB CMD AP / deactivate the
To change the operating mode, proceed as follows: SET LED starts to flash. function.
SET
A SEL
01 • Enter.MT.Pthe E Extended Menu 1 (see "EXTENDED MENU
AUS D
OT.P OT USA 1 ACCESS" on page 11B).
T.PA ED
SEL
T T.M T
.AU OT.P T
T.M T.MO
PGM/CORT
P. 02 • Press the SEL key .AU
T
03 • Press the SET
04 • The INB CMD AP LED on means that the function is active and the LED off means that the
P
LAM .CMD.A ED PGM/CORT
P.
once, and the CODE
P
IN DE P E
CO COD LAM .CMD.A ED
IN DE P E button once to
CO COD function is disabled.
LED begins to flash. change the operating
SET mode.
SET
SEL
SEL • LAMP/CORT | SLOWDOWN
This function enables / disables the existence of slowdown in opening and closing.
04 • The CODE LED will light on / off permanently, indicating that the change of operation
mode was successful. With this function disabled, it is not possible to set a slowdown during the motor's
working time programation, in both manual and automatic programming.
When you activate this function, you must make a new working time program (manual
• CODE PED. | ELECTRIC BRAKE or automatic), so that the changes become operational.
With this function active, when the automatism finishes a maneuver (reaching the The control board is supplied by the manufacturer with the slowdown active.
limit switch), the control board briefly reverses the motor's power supply to stop it
Enable (LED ON) / Disable (LED OFF) function:
immediately (eg. gates with inclination).
01 • Enter T.Pthe E Extended Menu 1 (see "EXTENDED MENU USA 1 ACCESS" on page 11B).
A
AUS D
The control board is supplied by the manufacturer with this function disabled. OT.P OT
T.M T.M T.PA D E
.AU
T OT.P T
T.M T.MO
PGM/CORT
02 • Press SEL button .AU
T
03 • Press once SET
Enable (LED ON) / Disable (LED OFF) function: P.
P
LAM .CMD.A ED PGM/CORT
P P.
A
IN DE P E
CO COD the times necessary LAM .CMD.A ED
IN DE P E button to activate
01 • EnterT.MT.Pthe
AUS D
OT.P OT Extended Menu 1 (see "EXTENDED MENU
E
.M
USA 1 ACCESS" on page 11B).
T.PA ED until the LAMP/CORT
CO COD
/ deactivate the
T
.AU
T OT.P T
T.M T.MO
PGM/CORT
P P. 02 • Press SEL button .AU
PGM/CORT
T
03 • Press the SET SET LED starts to flash. function.
LAM .CMD.A ED
P P. SET
IN DE P E
CO COD the times necessary LAM .CMD.A ED
IN DE P E button once to SEL
CO COD SEL
until the CODE PED change the operating
SET LED starts to flash. mode.
SEL
SET 04 • The LAMP/CORT LED will light on/off and the setup is complete.
SEL

04 • The CODE PED LED on means that the function is active and the LED off means that the
function is disabled.

13A 13B
EN EN
 04. PROGRAMMING 04. PROGRAMMING
EXTENDED MENU 1 EXTENDED MENU 2

• PGM. AUT. | FOLLOW ME The Extended Menu 2 allows you to program the motor's force/speed during the slowdown
With a programmed pause time, you can activate the "Follow Me" option. With this phase (idling). The control board has 6 different levels of force/speed, represented by
option enabled, whenever the photocells detect the passage of a user / object, the the combination of lit LEDs, as indicated in the table below.
control board triggers the closing maneuver after 5 seconds. The control board is supplied by the manufacturer with the power set at level 3.
The control board is supplied by the manufacturer with the function disabled.
Force Level
Enable (LED ON) / Disable (LED OFF) function:
LEDS
1 2 3 4 5 6
01 • Enter T.Pthe
T.PE OT Extended Menu 1 (see "EXTENDED MENU USA 1 ACCESS" on page 11B).
A
AUS D
.MO
T T.M T
T.PA D E
OT.P T
T.MOT
.AU T.M T.MO
PGM/CORT
P P. 02 • Press SEL button .AU
PGM/CORT
T
03 • Press once SET
LAM .CMD.A ED
IN DE P E
CO COD the times necessary
P P.
LAM .CMD.A ED
button to activate PGM.AUTO
IN DE P E
CO COD
until the PGM. AUT. / deactivate the L.CORT
SET LED starts to flash. function.
SET INB.CMD.AP
SEL
SEL
CODE PED
04 • The PGM. AUT. LED on means that the function is active and the LED off means that the CODE
function is disabled.

• T. MOT | PROGRAMMING TRANSMITTERS AT DISTANCE Program

T.PA EDthe idle force/speed through the Extended Menu 2:
USA
T.PO T
T.M T.MO

This function allows you to program new transmitters without access directly to the .AU
PGM/CORT
T
01 • Continuously 02 • The LEDs T.MOT.
P.
PED and T.PAUSA will
P
LAM .CMD.A ED
press the SET button USA
T.PA ED
control board, by using another already programmed transmitter to open the memory. IN DE P E
CO COD T.P
T.MO T.MOT
for 5 seconds to flash alternately.
The control board is supplied by the manufacturer with the function disabled. .AUT
PGMCORT
activate the Extended P/
SET LAM MD.AP.
Enable (LED ON) / Disable (LED OFF) function: Menu 1. IN.C E PED
COD CODE
SEL
USA
USA T.PA ED
01 • EnterT.MT.Pthe
OT.P OT Extended Menu 1 (see "EXTENDED MENU
A
ED USA 1 ACCESS" on page 11B).
T.PA ED
OT.P T
T.M T.MO
.M
T
.AU
T OT.P T
T.M T.MO
.AU
PGM/CORT
T
03 • Press again the 04 • The T.MOT.
PGM/CORT
P P.
LAM .CMD.A ED
02 • Press SEL button .AU
PGM/CORT
T
03 • Press once SET P P.
LAM .CMD.A ED
IN DE P E SET key for 5 seconds. T.PA EDSE
USA T PED and T.PAUSA
P P.
IN DE P E
CO COD the times necessary LAM .CMD.A ED
IN DE P E button to activate CO COD
SEL
T.P
T.MO T.MOT LEDs stop flashing
CO COD
until the T.MOT. LED / deactivate the .AUT
PGMCORT alternately and
P/
SET starts to flash. function. SET LAM MD.AP.
SET IN.C E PED start flashing
SEL USA COD CODE
SEL T.PA ED SA simultaneously.
SEL OT.P T U
T.M T.MO T.PA ED
.AU
T OT.P T
T.M T.MO
PGM/CORT
P P.
LAM .CMD.A ED
05 • Now press .AU
PGM/CORT
T
06 • Press the SET key
04 • The T.MOT. LED on means that the function is active and the LED off means that the SET
P.
the SEL button
P
IN DE P E
CO COD LAM .CMD.A ED
IN DE P E once, to selected that
CO COD
function is disabled. repeatedly to select SEL option.
SET the desired level of
Programming transmitter at distance: SET
SEL force.
01 • Press the button of an already programmed transmitter for 11seg, controlling with a SEL
clock, to open the control board's memory (when the memory opens, you hear a signal
through the flashing light). After entering the Extended Menu 2 , you have 30 seconds to select any function
02 • Press the new transmitter key for 1 second, to program it. of this menu (using the SEL and SET keys). After 30 seconds without pressing any
NOTE: If a new key is not pressed, after 10 seconds, the control board closes the memory. button, the control board returns to the main menu.

14A 14B
EN EN
 04. PROGRAMMING 05. MAINTENANCE
OTHER INFORMATION PARAMETERS TO TAKE CARE

• CONTROL BOARD'S RESET Before performing any maintenance, disconnect the control board from the
If you need to restore the control unit to the factory settings, follow these steps: electric current.
SA
AU ED

01 • Press the SEL 02 • All the LEDs

T.P T.P OT
O T.M UT
T.M .A T
M OR P.
PG P/C D.A ED
and SET buttons USA will light up
T.PA ED
M M P E

• VERIFICATIONS
LA IN.C DE COD
CO
T.P
T.MO T.MOT
simultaneously for 10 simultaneously and
SE
T .AUT
seconds. PGMCORT then off, completing
P/
LAM MD.AP.
Frequently check the installation for signs of lack of tightness or lubrication, imbalance
SE
L IN.C E PED
COD CODE
the operation. during functioning and traces of wear or deterioration.

Also check the condition of the installation and external components (switch, keyboard
SET or push buttons) and safety devices (photocells, safety edge) functioning. These are
• LEDS MANAGEMENT SEL exposed to external agents that may shorten their lifetime.
After 3 minutes of inactivity in the programming process, the control board automatically
turns off all the LEDs in order to save energy. If the device requires repair, bring/send it to our service center.
A simple click on a button (SEL, SET or programmed transmitter) will turn on the LEDs of
the programmed functions.
• ELIMINATION
At the end of its working life, the device must be removed from the place by a qualified
installer who must take into account all precautions and safety measures during the
procedure.
Never place the control board in household waste or uncontrolled landfills as it may
contaminate the environment. The control board must be placed in appropriate
recycling containers so that all components are separated according to their materials.

15A 15B
EN EN
 06. TROUBLESHOOTING 06. TROUBLESHOOTING
COMPONENTS TEST PHOTOCELLS AND TRANSMITTERS TEST

• PHOTOCELLS TEST
All the tests should be performed by qualified personnel due to the high risk
of accidents that may cause injury or death! The control board is prepared for the connection of safety devices in accordance with section
5.1.1.6 of EN 12453.
In every maneuver is performed a test for the Security Device and the lock.
To detect if the malfunction is on the control board or on the motor is, sometimes,
In case of a function/connection failure the motor doesn’t start and every LED’s remain in
necessary to perform tests with connection directly to a 110V / 230V power supply.
a intermittent mode, indicating the error. When the photocells operation is corrected, the
For this, it is necessary to interpose a capacitor on the connection in order to the
control board returns to it’s normal functioning. This action by the control board allows to
automatism to work (check the type of capacitor to be used in the product manual). recognize failures in accordance with is mentioned in category 2 of EN 954-1.
The diagram below, shows how to make that connection and how to merge the different
components wires.

NOTES: • TRANSMITTER'S TEST

> To perform the tests, there is no need to remove the automatism from the place it is instal-
led, because in this way, it is possible to understand if the automatism can function properly In the position corresponding to each transmitter input in low voltage, the control board has
connected directly to the current. a LED to identify the condition of it. The LED ON indicates that the input is closed, while the
> You should use a new capacitor during this test to ensure that the problem does not lie on LED OFF indicates that the input is open.
it.

01 • Connect the power wires to the terminal, as shown below.

02 • Connect the automatism wires in the terminal, interposing a capacitor in the
opening and closing wires.
03 • Once these connections are completed, connect to a 110V / 230V power outlet,
depending on the motor / control board in test.

Close Phase 1
Power Supply 1
Motor COM 1
COM
COM 2 3
Open
Power Supply 2
Phase 2

Ground Wire
8μF
Capacitor

1
2
2
AUTOMATISM

16A 16B
EN EN
 06. TROUBLESHOOTING
INSTRUCTIONS FOR FINAL CONSUMERS INSTRUCTIONS FOR SPECIALIZED INSTALLERS

Anomaly Procedure Behavior Procedure II Discovering the origin of the problem

• Motor • Make sure you have • Still not working • Consult a qualified 1 • Open control board and check 3 • Disconnect the motor from 4 • If the motor works, the 5 • If the motor doesn’t work,
doesn't work 110/230V power MOTORLINE technician. if it hás 110/230V power supply; control board and test them by problem is on the control board. remove them from installation
supply connected to connecting directly to power Pull it out and send it to our site and send to our MOTORLINE
automation and if it is 2 • Check the control board input supply in order to find out if they MOTORLINE technical services technical services for diagnosis.
working properly. fuses; have problems (see page 16.A). for diagnosis;

• Motor • Unlock motor and • Encountered • Consult an experienced 1 • Check all motion axis and associated motion systems related with the motor and the gate to find out what is the problem.
doesn’t move move the gate by hand problems? gate expert.
but makes to check for mechani-
noise cal problems on the • The gate moves • Consult a qualified 1 • Check capacitors, testing 2 • If capacitors are not the 3 • If the motors work, the 4 • If the motors doesn’t work,
movement. easily? MOTORLINE technician. operator with new capacitors; problem, disconnect motors from problem is from control board. remove them from installation
control board and test them by Pull it out and send it to our site and send to our MOTORLINE
connecting directly to power technical services for diagnosis; technical services for diagnosis.
supply in order to find out if they
have problems (see page 16.A);
• Motor opens • Unlock motor and • Gate opened but 1 • Check if there is any All MOTORLINE control boards have LEDs that A) SECURITY SYSTEMS: B) SISTEMAS DE START:
but doesn’t move the gate by hand didn’t close again. obstacle in front of the easily allow to conclude which devices are
close to closed position. photocells; with anomalies. All safety devices LEDs (DS) 1 • Close with a shunt all safety systems 1 • Disconnect all wires from START terminal
Lock motor again and 2 • Check if any of the control in normal situations remain On. All "START" on the control board (check manual of the input.
turn off power supply devices (key selector, push circuits LEDs in normal situations remain Off. control board in question). If the automated
for 5 seconds. Recon- button, video intercom, etc.) system starts working normally check for the 2 • If the LED turned Off, try reconnecting one
nect it and send order of the gate are jammed and If LEDs devices are not all On, there is some problematic device. device at a time until you find the defective
to open gate using sending permanent signal to security systems malfunction (photocells, device.
transmitter. control unit; safety edges), etc. If "START" circuits LEDs 2 • Remove one shunt at a time until you find
3 • Consult a qualified are turn On, there is a control device sending the malfunction device. NOTE: In case procedures described in
MOTORLINE technician permanent signal. sections A) and B) don’t result, remove control
3 • Replace it for a functional device and board and send to our technical services for
check if the motor works correctly with all the diagnosis.
other devices. If you find another one
defective, follow the same steps until you find
all the problems.

• Gate doesn’t • Unlock motor and • Encountered • Consult an experienced 1 • Check all motion axis and associated motion systems related with the gate to find out what is the problem.
make move gate by hand to problems? gate expert.
complete check for mechanical
route problems on the gate. • The gate moves • Consult a qualified 1 • Check capacitors, testing with and send to our MOTORLINE 5 • If this doesn’t work, remove NOTE:
easily? MOTORLINE technician. new capacitors; technical services for diagnosis. control unit and send it to Setting force of the controller
MOTORLINE technical services should be sufficient to make the
2 • If capacitors are not the 4 • If motor work well and move services. gate open and close without
problem, disconnect motor gate at full force during the entire stopping, but should stop and
from control board and test it course, the problem is from invert with a little effort from a
by connecting directly to power controller. Set force using person. In case of safety systems
supply in order to find out if it is trimmer on the board. Make a failure, the gate shall never cause
broken; new working time programming , physical damaged to obstacles
giving suffient time for opening (vehicles, people, etc.).
3 • If the motor doesn’t work, and closing with appropriate
remove it from installation site force (page 08.B or 9A).

17
EN