Epx Series

EPX-SERIES
Diagnostic X-ray System
Service Manual
Ecotron Co., Ltd

Made by Korea
4F&5F, Hanshin IT Tower II, 47, Digital-ro 9-gil, Geumcheon-Gu, Seoul 08511, Korea
Obelis S.A
Bd. General Wahis 53, 1030 Brussels, Belgium / E-mail:[email protected]
Representative: Mr.Gideon ELKAYAM / TEL:32.2.732.59.54, FAX:32.2.732.60.03
D/N: ECO-SM-EPX-001 Rev. G

EPX-SERIES SERVICE MANUAL
(This page intentionally left blank)
Rev. F 2/87 ECOTRON Co., Ltd.

CONTENTS
1. CALIBRATION ________________________________________________________ 8
1.1 EPX-F1600 ____________________________________________________________________________________ 8
1.1.1 LINE POWER SWITCH ___________________________________________________________________ 8
1.1.2 CALIBRATION PROCEDURE ____________________________________________________________ 8
1.2 EPX-F2400 __________________________________________________________________________________ 12
1.2.1 LINE POWER SWITCH _________________________________________________________________ 12
1.2.2 CALIBRATION PROCEDURE __________________________________________________________ 12
1.3 EPX-F2800 __________________________________________________________________________________ 16
1.4 EPX-F3200 __________________________________________________________________________________ 20
1.5 EPX-F4000 __________________________________________________________________________________ 24
1.6 EPX-F5000 __________________________________________________________________________________ 28
2. DIP SWITCH SETTING _________________________________________________ 32

3. HARD-WIRED HAND SWITCH CONTROL _________________________________ 33
3.1 HAND SWITCH INTRODUCTION___________________________________________________________ 33
3.2 EXPOSURE PROCESS _____________________________________________________________________ 33
4. COLLIMATOR ________________________________________________________ 34

5. TROUBLE SHOOTING _________________________________________________ 36
5.1 EPX-F1600 / F2400 / F2800 / F3200 / F4000 / F5000 ERROR CODE TABLE ______________ 36
5.2 ACTION TO CORRECT THE ERROR OF EPX-SERIES ____________________________________ 37
6. CALIBRATION _______________________________________________________ 38
6.1 EPX-F1600 __________________________________________________________________________________ 38
6.1.1 VOLTAGE CHECK ______________________________________________________________________ 38
6.1.2 kV, mA WAVEFORM CHECK ___________________________________________________________ 39
6.1.3 WAVEFORM OF POOR AC POWER CONDITION _____________________________________ 41
6.1.4 kV, mA PWM FREQUENCY CHECK ___________________________________________________ 42
6.1.5 mA CALIBRATION DATA CHECK _____________________________________________________ 43
6.1.6 FILAMENT PREHEAT CALIBRATION CODE AND DATA CHECK ____________________ 44
6.2 EPX-F2400 __________________________________________________________________________________ 46
6.2.1 VOLTAGE CHECK ______________________________________________________________________ 46
6.3 EPX-F2800 __________________________________________________________________________________ 54
6.3.1 VOLTAGE CHECK ______________________________________________________________________ 54

6.4 EPX-F3200 __________________________________________________________________________________ 62
6.4.1 VOLTAGE CHECK ______________________________________________________________________ 62
6.5 EPX-F4000 __________________________________________________________________________________ 70
6.5.1 VOLTAGE CHECK ______________________________________________________________________ 70
6.6 EPX-F5000 __________________________________________________________________________________ 79
6.6.1 VOLTAGE CHECK ______________________________________________________________________ 79

REVSON HISTORY
Revision Number Date Description
A SEP 11, 2013 First Edition

B SEP 30, 2014 European Authorized Representative Change
C JAN 12, 2015 Manual Updates
D MAR 23, 2015 Manual Updates
E JUN 11, 2015 Manual Updates
F AUG 23, 2018 Manual Update

G June 17, 2019 Modify misprinted contents
ADVISORY SYMBOLS
The following advisory symbols are used throughout this manual.
Their application and meaning are described below.
WARNING
Warning symbol used to indicate a potential hazard lead operators, service personnel to serious injury, death
or radiation exposure.
CAUTION
Caution symbol used to indicate a potential hazard lead operators, service personnel to injury or damage of
equipment.
NOTE
Note symbol used to indicate important information need to proper use and right operation of equipment.
NOTE
KEEP THIS SERVICE MANUAL WITH THE EQUIPMENT AT ALL TIMES, AND REVIEW THE
IMPORTANT INFORMATION WHENEVER REQUIRED.
THE STATISTICS AND SPECIFICATIONS OF THIS UNIT AND MANUAL CAN BE MODIFIED
WITH OR WITHOUT NOTIFICATION FOR THE IMPROVEMENT OF PERFORMANCE AND
SAFETY.

SERVICE CHAPTER
This manual is designed to ensure correct use and operation of EPX model diagnostic x-ray units. Please
read all the lines thoroughly before you use the equipment.
Incorrect use and operation exceeding described conditions in this manual may cause damage of the
equipment and shorten its life. Particular attention must be paid to all the warnings, cautions and notes
incorporated herein.
This equipment should be used only by the legally qualified persons and practitioners.
Regarding the AC cable and software, only the ones developed and supplied by Ecotron Co., Ltd should be
used.
Only trained maintenance staff may remove the covers of the x-ray system.
Do not modify the equipment at your discretion and in case any modification is required unavoidably, ask the
help of Ecotron or its authorized dealer for the service.
Information for repair will be provided by Ecotron. (Circuit diagram, Component part list, descriptions,
Calibration instructions, or other information)
No responsibility is taken by Ecotron for any infringement of patients or other rights of the third parties which
many results from the use of this manual.
Always keep the manual at hand for your reference.
NOTE: If the output calibration is needed after periodical inspections or repairs, please observe following rules
and methods described in this manual.
CAUTION
THE IONIZING RADIATION IS DANGEROUS FOR THE OPERATOR IF THE FOLLOWING

SAFETY MEASURES ARE NOT STRICTLY OBSERVED.
NOTE
ASSEMBLY INFORMATION: NO ASSEMBLY IS REQUIRED.

1. CALIBRATION
1.1 EPX-F1600
1.1.1 LINE POWER SWITCH
- Line switch should be at off position.

- Connect power line cord to the power outlet.
- Turn on the line switch.
- The FND on the control panel should illuminate.
1.1.2 CALIBRATION PROCEDURE
1.1.2.1 TUBE VOLATAGE CONFIRMATION AND CALIBRATION
a. Turn off the line switch.

b. Detach the control panel from the unit to access the PCB OP BOARD.
c. Connect the channel one probe of the oscilloscope to TP8 (IP F/B).
d. Connect the channel two probe of the oscilloscope to TP11 (EP F/B).
e. Connect the ground to TP13 or TP14 (GND) on the OP board.
f. Turn on the line switch.
g. Set the kV and the mAs at 40 KV and 5 mAs (30mA), respectively.
h. Then observe the KV waveform of the oscilloscope channel 2.
i. If it is not 2V, adjust KV by turning VR3 on the OP board.
j. Set the kV and the mAs at 90 KV and 5 mAs (16 mA), respectively.
k. Then observe the KV waveform of the oscilloscope channel 2.
l. If it is not 4.5 V, adjust KV by turning VR3 on the OP board.

1.1.2.2 TUBE CURRENT CONFIRMATION AND CALIBRATION

c. Connect the channel one (1) probe of the oscilloscope to TP8 (IP F/B).
d. Connect the channel two (2) probe of the oscilloscope to TP11 (EP F/B).
g. Set the kV and the mAs at 40 kV and 5 mAs (30 mA), respectively.
h. Then observe the mA waveform of the oscilloscope channel 1.
i. If it is not 6V, adjust mA using the calibration data on the OP BOARD.
j. DIP SWITCH #4 on the OP BOARD PCB is set to ON position.
Then the display should indicate as follows,
Where, C00~C09 are calibration code of tube current at AC110V model and C10~C19 are calibration code of
tube current at AC220V model.
C00 or C10 is calibration code of tube current (30mA at 40kV~50kV) at AC110V or AC220V and 30.0 is
calibration data of tube current (30mA at 40kV~50kV).

a. Adjust mA by using the mAs Up-Down switch (see operation sheet).

b. After it is adjusted, push the STORE button during 3sec (see operation sheet).
c. DIP SWITCH #4 on the PCB OP BOARD should be set to OFF position and the expose X-ray.
e. If it is not 6V, set the calibration data again.
f. DIP SWITCH #4 on the OP BOARD PCB is set to ON position.
g. Then push the kV UP switch (see operation sheet).
h. The display should indicate as follows,
Where, C01 or C11 is calibration code of tube current (25mA at 40kV~50kV) and 25.0 is calibration data of
tube current (25mA at 40kV~50kV).
i. Adjust mA by using the mAs Up-Down switch (see operation sheet).

j. After it is adjusted, push the STORE switch during 3sec (see operation sheet).
k. DIP SWITCH #4 on the PCB OP BOARD is set to OFF position then expose X-ray.
l. If it is not 5V, set the calibration data again.
Filament preheat calibration
This is preheating filament for making tube current. The overshooting or the undershooting may occur from
the tube current if the Preheat calibration data is set by mistake. Changing the calibration data is possible in
accordance with the tube condition.

c. DIP SWITCH #4 on the PCB OP BOARD is set to ON position.
d. Turn on the line switch.
f. Push APR S/W ① and then the display should indicate as follows,

Where, P00~P07 are calibration code of filament preheat current at AC110V, P08~P15 are calibration code of
filament preheat current at AC220V, P00 or P08 is Filament preheat calibration code (Preheat calibration code
of 30mA), and 1.50 or 1.40 is Filament preheat calibration data (Preheat calibration data of 30mA).
g. Adjust data by using the mAs Up-Down switch (see operation sheet).
h. After it is adjusted, push the STORE button during 3sec(see operation sheet).
i. DIP SWITCH #4 on the PCB OP BOARD is set to OFF position then expose X-ray.
j. If overshooting or undershooting occurs in the waveform, set the calibration data again.
k. Then push the KV UP switch (see operation sheet).
l. The display should indicate as follows,
Where, P01 or P09 is Filament preheat calibration code (Preheat calibration code of 25mA) and 1.45 or 1.35
is Filament preheat calibration data (Preheat calibration data of 25mA).
m. Adjust data by using the mAs Up-Down switch on the Control Panel.
n. After it is adjusted, push the Store switch during 3sec(see operation sheet).
o. DIP SWITCH #4 on the PCB OP BOARD is set to OFF position then exposure X-ray.
p. If overshooting or undershooting occurs in the waveform, set the calibration data again.

1.2 EPX-F2400


g. Set the kV and the mAs at 40 KV and 5 mAs (40mA), respectively.
l. If it is not 5 V, adjust KV by turning VR3 on the OP board.





l. If it is not 5.25V, set the calibration data again.


h. After it is adjusted, push the STORE button during 3sec (see operation sheet).
n. After it is adjusted, push the Store switch during 3sec (see operation sheet).

1.3 EPX-F2800


g. Set the kV and the mAs at 40KV and 5mAs (40mA), respectively.
l. If it is not 6 V, adjust KV by turning VR3 on the OP board.







where, P00~P06 are calibration code of filament preheat current at AC110V, P07~P13 are calibration code of

1.4 EPX-F3200


e. Connect the ground to TP13 or TP14 on the OP board.
j. Set the kV and the mAs at 100KV and 5mAs(30mA), respectively.

l. If it is not 5V, adjust KV by turning VR3 on the OP board.


tube current at AC220V model. C00 or C08 is calibration code of tube current (60mA at 40kV~50kV) at
AC110V and 60.0 is calibration data of tube current (60mA at 40kV~50kV).


e. If it is not 6.0V, set the calibration data again.




1.5 EPX-F4000


i. If it is not 2.5V, adjust KV by turning VR3 on the OP board.
j. Set the kV and the mAs at 110KV and 5mAs (25mA), respectively.
l. If it is not 5.5V, adjust KV by turning VR3 on the OP board.


i. If it is not 5.44V, adjust mA using the calibration data on the OP BOARD.
Where, C00~C14 are calibration code of tube current at AC110V model and C15~C29 are calibration code
of tube current at AC220V model. C00 or C15 is calibration code of tube current (80mA at 50kV) at 80.0 is
calibration data of tube current (80mA at 50kV).


b. After it is adjusted, push the STORE button during 3sec(see operation sheet).
Where, C01 or C16 is calibration code of tube current (70mA at 50kV) and 70.0 is calibration data of tube
current (70mA at 50kV).



h. After it is adjusted, push the STORE button during 3sec (see operation sheet).

1.6 EPX-F5000


i. If it is not 2.0V, adjust KV by turning VR3 on the OP board.
j. Set the kV and the mAs at 110KV and 5mAs (40mA), respectively.
l. If it is not 5.5V, adjust KV by turning VR3 on the OP board.


i. If it is not 5.1V, adjust mA using the calibration data on the OP BOARD.
tube current at AC220V model. C00 or C21 is calibration code of tube current (100mA at 50kV) at A0.0(=100)
is calibration data of tube current (100mA at 50kV).


e. If it is not 5.1V, set the calibration data again.
Where, C01 or C22 is calibration code of tube current (80mA at 50kV) and 80.0 is calibration data of tube
current (80mA at 50kV).

j. After it is adjusted, push the STORE switch during 3sec(see operation sheet).


n. After it is adjusted, push the Store switch during 3sec (see operation sheet).

2. DIP SWITCH SETTING
DIP Switches are used for following setting.
SW #1: ERROR Disable (ON) / Enable (OFF)

SW #2: Reserved
SW #3: Initialize memories (reserved)
SW #4: Calibration mode (ON) / Normal mode (Off)
For normal operation, only the DIP SW#1 must be set to OFF position.

3. HARD-WIRED HAND SWITCH CONTROL
3.1 HAND SWITCH INTRODUCTION
The Exposure Hand Switch consists of a two step hand switch.

The first (1) stage of the hand switch is called the “Preparation (Prep or READY)” stage.
The second (2) stage of the hand switch is called the “Exposure (Exp or X-Ray Out)“ stage.
3.2 EXPOSURE PROCESS
There are two ways to use the hand switch to get the exposure.
a. Press and hold the Switch #1 for longer than 1 second, which will get the “Prep or Ready” status on, then
press Switch #2 to get the “Exposure”.
b. Press and hold the Switch #1 and Switch #2 simultaneously for longer than 1 second. This action will result
in “Prep or Ready” status and “Exposure” at the same time.

4. COLLIMATOR
a. Halogen Lamp * 1
b. Laser pointer * 2
c. Horizontal and vertical lighting range control
I. Block Diagram
II. Layout
a. External Layout

b. Internal Layout
c. Knob Layout

5. TROUBLE SHOOTING
If you have any error message when you are using portable x-ray, please check below service check list
5.1 EPX-F1600 / F2400 / F2800 / F3200 / F4000 / F5000 ERROR CODE TABLE
Error
DESCRIPTION INDICATION
Code
2 THERMAL ERROR (INTERLOCK) Excess from 60℃
7 READY SW ERR Ready Switch Malfunction
8 EXPOSURE SW ERROR Exposure Switch Malfunction
10 STANDBY FIL FB ERROR Excess from 200mA (10% of Max. Current, 2A)
11 STANDBY EP FB ERROR Excess from 12kV (10% of Max. Voltage, 120kV)
12 STANDBY IP FB ERROR Excess from 3.5mA (10% of Max. Current, 35mA)
14 RUN FIL FB ERROR Out of Range from Reference ±10%
RUN EP FB or AC POWER LOW Out of Range from Reference -10% or AC Power Line
15
ERROR poor
16 RUN IP FB HIGH ERROR Out of Range from Reference +10%
17 RUN EP FB HIGH ERROR Out of Range from Reference +10%
18 RUN IP FB LOW ERROR Out of Range from Reference -10%
28 PULSE BY PULSE ERROR FET Board Fault (Hardware)
29 FET-OTP ERROR FET board overheat
30 KV_OVP ERROR kV Over Voltage (Hardware)
31 FIL_OC ERROR FIL Over Current (Hardware)
32 IP_OCP ERROR mA Over Current (Hardware)

5.2 ACTION TO CORRECT THE ERROR OF EPX-SERIES
Error Codes Check points and Action
7 Ready SW ERR
a. Replace the hand switch
8 Exposure SW ERR
10 Standby Fil FB Error

a. If error repeats at the condition of 40kV 0.4mAs EXP, replace the OP
11 Standby EP FB Error
board
12 Standby IP FB Error
14 Run Fil FB Error

a. If error repeats at the condition of 40kV 0.4mAs EXP, check the followings
15 Run EP FB low ERR
by sequence.
1. Check TP in the power input of the OP board
16 Run IP FB High ERR
2. Check the Reference voltage value
17 Run EP FB High ERR 3. If the reference voltage is normal, replace the FET board
4. If replacing FET board does not solve the problem, the replace the
18 Run IP FB low ERR
HV tank.
28 Pulse by Pulse ERR
a. If error pops up right after the unit power is turned on, then replace the
30 KV_OVP ERR
OP board.
31 FIL_OC ERR FIL b. If error repeats at the condition of 40kV 0.4mAs EXP,
1. Replace the FET board
2. If replacing FET board does not solve the problem, the replace the
32 IP_OCP ERR
HV tank.
Warning Codes
Thermal ERR excess Wait until the temperature inside the monotank comes down to normal
2
from 60°C (Once the temperature drop to normal, the Warning Message will disappear)
FET-OTP FET board Wait until the temperature inside the FET board comes down to normal
29
overheat (Once the temperature drop to normal, the Warning Message will disappear)

6. CALIBRATION
6.1 EPX-F1600
Please fill in the blank.
Kv / mAs condition
Product S/N Error code
(When error is occurred)
※ Open upper cover of portable x-ray below picture.
6.1.1 VOLTAGE CHECK
1) Turn on AC switch
TP26 TP24 TP25 TP6
VDC Range 4.8V~5.0V 11.5V~12.5V -11.5V~-12.5V +3V~3.6V
Pass Fail Pass Fail Pass Fail Pass Fail

Pass/Fail
Measured Voltage
If it is fail case

6.1.2 kV, mA WAVEFORM CHECK
1) Turn off AC switch

2) Please connect probe to EP_FB (kV feedback_TP11), IP_FB (mA feedback_TP8) test point on operation
board below picture.
3) Turn on AC switch.
4) 40kV/5mAs waveform
Please set kV, mAs below table and take exposure
Exposure condition : 40kV/5mAs
CH 1: kV 2V/div CH 2: mA 2V/div 40msec/div
Setting value EP_FB IP_FB

Ref voltage 40kV 2V 5.1V
Pass/Fail Pass Fail Pass Fail
Measured kV feedback voltage
If kV, mA waveforms are fail, please attach your kV, mA waveform


If kV,mA waveforms are fail, please attach your kV, mA waveform

Ref voltage 90kV 4.5V 2.72V

6.1.3 WAVEFORM OF POOR AC POWER CONDITION
If AC power is under 100V or 200VAC, you have below abnormal waveform. Error 015,016,017,018 is
occurred by poor AC power.

6.1.4 kV, mA PWM FREQUENCY CHECK
1) Turn off AC swtich

2) Please connect probe to 80 kHz (TP15), 140 kHz (TP16) test point on operation board below picture.
4) kV / mA PWM frequency
CH 1: kV 2V/div CH 2 : mA 2V/div 4μsec/div
CH CH 1 mA PWM CH 2 kV PWM
Frequency 80kHz 140kHz
Measured frequency

6.1.5 mA CALIBRATION DATA CHECK
DIP Switches are used for following setting:

SW #1: ERROR Enable (ON) / Disable (OFF)
SW #2: Reserved
For normal operation, only the DIP SW#1 must be set to ON position.
DIP SWITCH #4 on the OP BOARD PCB is set to ON position.
Up/Down switches increase and decrease C00~C09 (AC110V), C10~C19 (AC220V).

Please check Input data.
Input data and Tube current should be the same with below table.

Tube Current Parameter Tube Voltage mAs Tube Current INPUT DATA
AC110V AC220V KV MIN MAX mA mA
C00 C10 40~50 (1) 0.4 20 30.0 30.0
C01 C11 40~50 (2) 25 32 25.0 25.0
C02 C12 51~60 (1) 0.4 20 25.0 25.0
C03 C13 51~60 (2) 25 32 20.0 20.0
C04 C14 61~70 (1) 0.4 20 20.0 20.0
C05 C15 61~70 (2) 25 32 15.0 15.0
C06 C16 71~80 (1) 0.4 20 18 18
C07 C17 71~80 (2) 25 32 14 14
C08 C18 81~90 (1) 0.4 20 16 16
C09 C19 81~90 (2) 25 32 12 12
4) If mA calibration is done, Please dip switch 4 set to OFF position.
6.1.6 FILAMENT PREHEAT CALIBRATION CODE AND DATA CHECK

2) Dip switch on op board

SW #2: Reserved

4) In mA calibration mode, Press the number 1 switch as shown in figure. Mode is converted.
Up/Down switches increase and decrease P00~P07 (AC110V), P08~P15 (AC220V)

Input data and Tube current should be the same.
Fill in the blank below table because P_DATA is different for each product.
Model Current(mA) P_Mode (110V) P_Mode (220V) P_DATA
30 P00 P08
25 P01 P09
20 P02 P10
18 P03 P11
1.6kW
16 P04 P12
15 P05 P13
14 P06 P14
12 P07 P15
5) If Preheat calibration is done, Please dip switch 4 set to OFF position.

6.2 EPX-F2400
Kv / mAs condition
6.2.1 VOLTAGE CHECK
TP26 TP24 TP25 TP6

Pass/Fail
Measured Voltage
If it is fail case



Ref voltage 40kV 2V 6V



Ref voltage 100 kV 5V 3V



Measured frequency


SW #2: Reserved


C00 C08 40~60(1) 0.4 64 40.0 40.0
C01 C09 40~60(2) 80 100 35.0 30.0
C02 C10 61~70(1) 0.4 100 30.0 25.0
C03 C11 71~80(1) 0.4 32 30.0 30.0
C04 C12 71~80(2) 40 80 25.0 25.0
C05 C13 81~90(1) 0.4 40 25.0 25.0
C06 C14 81~90(2) 50 80 20.0 20.0
C07 C15 91~100(1) 0.4 80 20.0 20.0


SW #1: ERROR Enable (ON )/ Disable (OFF)
SW #2: Reserved


40 P00 P05
35 P01 P06
30 P02 P07
25 P03 P08
2.4 kW
20 P04 P09

6.3 EPX-F2800
Kv / mAs condition
6.3.1 VOLTAGE CHECK
TP26 TP24 TP25 TP6

Pass/Fail
Measured Voltage
If it is fail case






Ref voltage 120 kV 6V 2.4V



Measured frequency


SW #2: Reserved


C00 C16 40~60 0.4 100 40.0 40.0
C01 C17 61~70(1) 0.4 64 30.0 30.0
C02 C18 61~70(2) 80 100 25.0 25.0
C03 C19 71~80(1) 0.4 10 35.0 35.0
C04 C20 71~80(2) 13 32 30.0 30.0
C05 C21 71~80(3) 40 80 25.0 25.0
C06 C22 81~90(1) 0.4 10 30.0 30.0
C07 C23 81~90(2) 13 40 25.0 25.0
C08 C24 81~90(3) 50 80 20.0 20.0
C09 C25 91~100(1) 0.4 13 25.0 25.0
C10 C26 91~100(2) 16 50 20.0 20.0
C11 C27 91~100(3) 64 80 16.0 16.0
C12 C28 101~110(1) 0.4 32 18.0 18.0
C13 C29 101~110(2) 40 64 16.0 16.0
C14 C30 111~120(1) 0.4 20 16.0 16.0
C15 C31 111~120(2) 25 50 14.0 14.0



SW #2: Reserved

40 P00 P08
35 P01 P09
30 P02 P10
25 P03 P11
2.8 kW
20 P04 P12
18 P05 P13
16 P06 P14
14 P07 P15

6.4 EPX-F3200
Kv / mAs condition
6.4.1 VOLTAGE CHECK
TP26 TP24 TP25 TP6

Pass/Fail
Measured Voltage
If it is fail case






Ref voltage 100 kV 5V 3V



Measured frequency


SW #2: Reserved


C00 C08 40~50 0.4 100 60.0 60.0
C01 C09 51~60 0.4 80 50.0 50.0
C02 C10 61~70 0.4 100 40.0 40.0
C03 C11 71~80(1) 0.4 32 40.0 40.0
C04 C12 71~80(2) 40 80 35.0 35.0
C05 C13 81~90 0.4 80 30.0 30.0
C06 C14 91~100(1) 0.4 50 30.0 30.0
C07 C15 91~100(2) 64 80 25.0 25.0


SW #2: Reserved


60 P00 P06
50 P01 P07
40 P02 P08
35 P03 P09
3.2 kW
30 P04 P10
25 P05 P11

6.5 EPX-F4000
Kv / mAs condition
6.5.1 VOLTAGE CHECK
TP26 TP24 TP25 TP6

Pass/Fail
Measured Voltage
If it is fail case



Ref voltage 50kV 2.5V 5.44V



Ref voltage 110 kV 5.5V 2.04V



Measured frequency


SW #2: Reserved


Tube Current
Tube Voltage mAs Tube Current INPUT DATA
Parameter
AC 110V AC 220V KV MIN MAX mA mA
C00 C15 50 (1) 0.4 16 80.0 80.0
C01 C16 50 (2) 20 32 70.0 70.0
C02 C17 50 (3) 40 100 60.0 60.0
C03 C18 51~60 (1) 0.4 32 60.0 60.0
C04 C19 51~60 (2) 40 100 50.0 50.0
C05 C20 61~70 (1) 0.4 32 50.0 50.0
C06 C21 61~70 (2) 40 100 40.0 40.0
C07 C22 71~80 (1) 0.4 10 45.0 45.0
C08 C23 71~80 (2) 13 80 40.0 40.0
C09 C24 81~90 (1) 0.4 32 35.0 35.0
C10 C25 81~90 (2) 40 80 30.0 30.0
C11 C26 91~100 (1) 0.4 32 30.0 30.0
C12 C27 91~100 (2) 40 80 25.0 25.0
C13 C28 101~110 (1) 0.4 32 25.0 25.0
C14 C29 101~110 (2) 40 80 20.0 20.0



SW #2: Reserved


Model Current(mA) P_Mode(110V) P_Mode(220V) P_DATA
80 P00 P10
70 P01 P11
60 P02 P12
50 P03 P13
45 P04 P14
4.0KW
40 P05 P15
35 P06 P16
30 P07 P17
25 P08 P18
20 P09 P19

6.6 EPX-F5000
Kv / mAs condition
6.6.1 VOLTAGE CHECK
TP26 TP24 TP25 TP6

Pass/Fail
Measured Voltage
If it is fail case






Ref voltage 110 kV 5.5V 1.53V



Measured frequency


SW #2: Reserved


C00 C21 50(1) 0.4 10 100 100
C01 C22 50(2) 13 32 80 80
C02 C23 50(3) 40 100 70 70
C03 C24 51~60(1) 0.4 10 80 80
C04 C25 51~60(2) 13 32 70 70
C05 C26 51~60(3) 40 100 60 60
C06 C27 61~70(1) 0.4 10 70 70
C07 C28 61~70(2) 13 32 60 60
C08 C29 61~70(3) 40 100 50 50
C09 C30 71~80(1) 0.4 10 60 60
C10 C31 71~80(2) 13 32 50 50
C11 C32 71~80(3) 40 100 40 40
C12 C33 81~90(1) 0.4 10 50 50
C13 C34 81~90(2) 13 32 40 40
C14 C35 81~90(3) 40 100 30 30
C15 C36 91~100(1) 0.4 10 45 45
C16 C37 91~100(2) 13 32 40 40
C17 C38 91~100(3) 40 100 30 30
C18 C39 101~110(1) 0.4 10 40 40
C19 C40 101~110 (2) 13 32 30 30
C20 C41 101~110 (3) 40 100 20 20



SW #2: Reserved


Model Current(mA) P_Mode(110V) P_Mode(220V) P_DATA(A)
100 P00 P09
80 P01 P10
70 P02 P11
60 P03 P12
5kW 50 P04 P13
45 P05 P14
40 P06 P15
30 P07 P16
20 P08 P17

Epx Series

Uploaded by

Copyright:

Available Formats

Epx Series

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Epx Series

Uploaded by

Copyright:

Available Formats

EPX-SERIES

Diagnostic X-ray System

Ecotron Co., Ltd

D/N: ECO-SM-EPX-001 Rev. G

(This page intentionally left blank)

Rev. F 2/87 ECOTRON Co., Ltd.

1.1 EPX-F1600 ____________________________________________________________________________________ 8

1.1.1 LINE POWER SWITCH ___________________________________________________________________ 8

1.1.2 CALIBRATION PROCEDURE ____________________________________________________________ 8

1.2 EPX-F2400 __________________________________________________________________________________ 12

1.2.1 LINE POWER SWITCH _________________________________________________________________ 12

1.2.2 CALIBRATION PROCEDURE __________________________________________________________ 12

1.3 EPX-F2800 __________________________________________________________________________________ 16

1.3.1 LINE POWER SWITCH _________________________________________________________________ 16

1.3.2 CALIBRATION PROCEDURE __________________________________________________________ 16

1.4 EPX-F3200 __________________________________________________________________________________ 20

1.4.1 LINE POWER SWITCH _________________________________________________________________ 20

1.4.2 CALIBRATION PROCEDURE __________________________________________________________ 20

1.5 EPX-F4000 __________________________________________________________________________________ 24

1.5.1 LINE POWER SWITCH _________________________________________________________________ 24

1.5.2 CALIBRATION PROCEDURE __________________________________________________________ 24

1.6 EPX-F5000 __________________________________________________________________________________ 28

1.6.1 LINE POWER SWITCH _________________________________________________________________ 28

1.6.2 CALIBRATION PROCEDURE __________________________________________________________ 28

2. DIP SWITCH SETTING _________________________________________________ 32

3.1 HAND SWITCH INTRODUCTION___________________________________________________________ 33

3.2 EXPOSURE PROCESS _____________________________________________________________________ 33

Rev. F 3/87 ECOTRON Co., Ltd.

5. TROUBLE SHOOTING _________________________________________________ 36

5.2 ACTION TO CORRECT THE ERROR OF EPX-SERIES ____________________________________ 37

6.1 EPX-F1600 __________________________________________________________________________________ 38

6.1.1 VOLTAGE CHECK ______________________________________________________________________ 38

6.1.2 kV, mA WAVEFORM CHECK ___________________________________________________________ 39

6.1.3 WAVEFORM OF POOR AC POWER CONDITION _____________________________________ 41

6.1.4 kV, mA PWM FREQUENCY CHECK ___________________________________________________ 42

6.1.5 mA CALIBRATION DATA CHECK _____________________________________________________ 43

6.1.6 FILAMENT PREHEAT CALIBRATION CODE AND DATA CHECK ____________________ 44

6.2 EPX-F2400 __________________________________________________________________________________ 46

6.2.1 VOLTAGE CHECK ______________________________________________________________________ 46

6.2.2 kV, mA WAVEFORM CHECK ___________________________________________________________ 47

6.2.3 WAVEFORM OF POOR AC POWER CONDITION _____________________________________ 49

6.2.4 kV, mA PWM FREQUENCY CHECK ___________________________________________________ 50

6.2.5 mA CALIBRATION DATA CHECK _____________________________________________________ 51

6.2.6 FILAMENT PREHEAT CALIBRATION CODE AND DATA CHECK ____________________ 52

6.3 EPX-F2800 __________________________________________________________________________________ 54

6.3.1 VOLTAGE CHECK ______________________________________________________________________ 54

6.3.2 kV, mA WAVEFORM CHECK ___________________________________________________________ 55

6.3.3 WAVEFORM OF POOR AC POWER CONDITION _____________________________________ 57

6.3.4 kV, mA PWM FREQUENCY CHECK ___________________________________________________ 58

6.3.5 mA CALIBRATION DATA CHECK _____________________________________________________ 59

6.3.6 FILAMENT PREHEAT CALIBRATION CODE AND DATA CHECK ____________________ 60

Rev. F 4/87 ECOTRON Co., Ltd.

6.4 EPX-F3200 __________________________________________________________________________________ 62

6.4.1 VOLTAGE CHECK ______________________________________________________________________ 62

6.4.2 kV, mA WAVEFORM CHECK ___________________________________________________________ 63

6.4.3 WAVEFORM OF POOR AC POWER CONDITION _____________________________________ 65

6.4.4 kV, mA PWM FREQUENCY CHECK ___________________________________________________ 66

6.4.5 mA CALIBRATION DATA CHECK _____________________________________________________ 67