Scribd
Upload
233 views

Lab No.2 Modeling A Micro Strip Transmission Line in ADS: Objective: Theory

This document describes how to model a microstrip transmission line in Agilent Advanced Design System (ADS) by designing a line with a 50 ohm characteristic impedance on a substrate with a permittivity of 2.2 and thickness of 1.57mm, simulating its S-parameters to validate the design, and includes two additional tasks of designing 25 ohm and FR-4 substrate lines.

Uploaded by

muhammad jehangir
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
233 views

Lab No.2 Modeling A Micro Strip Transmission Line in ADS: Objective: Theory

This document describes how to model a microstrip transmission line in Agilent Advanced Design System (ADS) by designing a line with a 50 ohm characteristic impedance on a substrate with a permittivity of 2.2 and thickness of 1.57mm, simulating its S-parameters to validate the design, and includes two additional tasks of designing 25 ohm and FR-4 substrate lines.

Uploaded by

muhammad jehangir
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

Lab No.

2 Modeling a Micro strip Transmission line in


ADS
Objective:
To familiarize the students with microstrip transmission lines ADS.
Theory:
Agilent Advanced Design System (ADS) is an industry standard microwave engineering
computer-aided-design (CAD) program. Agilent ADS allows microwave engineers to analyze,
design, and simulate active and passive microwave components and systems. In this tutorial, a
microstrip transmission line will be designed and analyzed. It should be noted that there are two
ways to design/simulate in Agilent ADS; schematic (equation-based) or full-wave (Method-of-
Moments). The microstrip line will be designed and simulated using the schematic simulator in
this lab.

Microstrip Transmission Line Design Values

 Operational Frequency: 1 GHz to 5 GHz


 Substrate: 2.2 Permittivity and Height of 1.57 mm
 Characteristic Impedance: 50 Ohm
 Electrical length: 90 degrees at 2.4 GHz.

Figure 1. Agilent ADS window.

Once you have given a name to the new project a new schematic window will appear as shown
in Fig. 2. On the left side of the schematic window is the Palette List and Component Palette, the
Palette List allows you to chose different simulation and microwave circuit components.
Figure 2. Schematic layout window.

An S-Parameter simulation will be performed on the microstrip transmission line. Therefore, use
the Palette Listand pick Simulation-S_Param, the Component Palette will change and S-
Parameter simulation components can now be chosen. Place a SP and two Term components
onto the layout region. The Term component lets ADS know how many ports and the port
impedance (50 Ohms in our case) for the S-Parameter simulation. An S-Parameter simulation
from 1 GHz to 5 GHz with 401 points will be performed, therefore double-click
the SPcomponent and change the necessary values. After placing the S-Parameter components, your
schematic window should look like Fig. 3.
Figure 3. Schematic layout window showing required S-Parameter components.

Next, the microstrip line has to be defined and placed onto the schematic layout window. To do
this, click on thePalette List and choose TLines-Microstrip. The substrate on which the
microstrip line will be designed on has to be defined. To do this, place the MSUB component
onto the layout region and double-click on it. The properties of the microstrip substrate can be
changed; change the substrate height (H) to 1.57 mm and the dielectric permittivity (Er) to 2.2.

Next, place a MLIN component onto the layout region and connect it to the
two Term components. The width (W) and length (L) of the MLIN component has to be
changed to obtain the correct characteristic impedance and phase shift, respectively. To calculate
the required width (W) to provide a 50 Ohm characteristic impedance, select
the MLIN component and then go to Tools>LineCalc>Send Selected Component to
LineCalc enter a design frequency of 2.4 GHz. Fig. 4 shows the LineCalc window. It is
important to double check the substrate definition. For the Electrical properties enter 50 for the
impedance and 90 for the E_Eff (effective electrical length). Once you are done click on
synthesize and the width (W=4.84 mm) and length (L=22.70 mm) will be calculated. Enter these
values for the MLIN component. The finished layout window should look like Fig. 5.
Figure 4. LineCalc window.

Figure 5. Completed layout.


At this point, you should save your design.To simulate the design, go to Simulate>Simulate.
After simulation is complete, a data window will appear. Here you can plot the S-parameter data
in different formats and in different types of charts. Fig. 6 shows the data window with a plot of
S11 and S21 magnitude and a plot of the phase between Port 1 and Port 2 of the microstrip line
component. The magnitude plot confirms that the microstrip line is indeed 50 Ohms, while the
phase plot confirms that at 2.4 GHz the electrical length is 90 degrees.

Figure 6. Data plot window showing S-parameter results.

Lab Task:
1. Calculate and simulate the microstrip transmission line for 25ohms instead of
conventional 50ohms transmission line for above performed task.
2. Calculate and simulate the microstrip transmission line for FR-4 substrate of permittivity
4.4 and height of 1.6mm.

You might also like