Scribd Logo
Upload

Welcome to Scribd!

  • 62 views

    Quick Start Guide: Remotelinc - Insteon Wireless Remote Control

    Uploaded by

    rando

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Quick Start Guide: Remotelinc - Insteon Wireless Remote Control

    Uploaded by

    rando
    62 views1 page

    Original Title

    Insteon 2440qs-en

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    62 views1 page

    Quick Start Guide: Remotelinc - Insteon Wireless Remote Control

    Uploaded by

    rando

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    Quick Start Guide

    RemoteLinc™ – INSTEON® Wireless Remote Control


    Model #2440BK

    Introduction Customizable
    RemoteLinc allows you to use the power of INSTEON to control label insert On/Off
    button
    your home with the convenience of a handheld wireless pairs
    controller. RemoteLinc can control up to six scenes and features
    a customizable label insert.

    Setting Up RemoteLinc
    1) RF-only devices require at least one dual-band INSTEON
    Status
    device for communication. For the best INSTEON network LED
    performance, be sure you have properly installed at least
    two Access Points or other dual-band INSTEON devices.
    2) Remove the battery compartment from the rear of
    RemoteLinc and install four AAA batteries. Dedicated
    3) Replace the battery compartment door. Dim/Brighten Dedicated
    buttons simultaneous-
    control
    NOTE: Use alkaline batteries, or high quality rechargeable buttons
    batteries. A fully charged set of alkaline batteries will provide
    approximately 1,500 – 2,000 button taps.

    Using RemoteLinc as an INSTEON Controller


    1) On RemoteLinc, press and hold the On button of the button pair you wish to use until it beeps (10 seconds).
    RemoteLinc’s status LED will begin blinking.
    2) Set the responder to the state you want to activate from RemoteLinc.
    3) Press and hold the responder’s Set button for 3 seconds
    RemoteLinc will beep and its status LED will turn off.
    4) Test link by tapping the On/Off buttons you just linked to on RemoteLinc.
    The responder should respond appropriately.

    Using RemoteLinc
    Each button on RemoteLinc has a dual purpose. Linked responders will behave differently depending on what button you
    press, and whether it is tapped or pressed and held.

    Button Applies To Tap Press and Hold


    On Device(s) linked to that specific button pair Ramp to On-Level Brighten until release
    Off Device(s) linked to that specific button pair Ramp to Off Dim until release
    All On All devices linked to RemoteLinc Fast-on Brighten until release
    All Off All devices linked to RemoteLinc Fast-off Dim until release
    Brighten Device(s) linked to last On/Off button pushed Brighten by 3 levels (out of 32) Brighten until release
    Dim Device(s) linked to last On/Off button pushed Dim by 3 levels (out of 32) Dim until release
    NOTE: Non-dimming responders will not be affected by brighten/dim commands or pressing and holding any of the buttons.

    Complete Instructions, Troubleshooting and Tech Support


    Owner’s Manual and Quick Start Guide: http://www.insteon.com/support
    Call: INSTEON Support Line at 800-762-7845

    *Setup Modes automatically time out after 4 minutes.

    This device complies with FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference,
    and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
    Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes: (1) l'appareil ne doit pas
    produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement.

    INSTEON Limited Warranty – INSTEON warrants to original consumer of this product for a period of 2 years from date of purchase, this product will be free
    from defects in material and workmanship and will perform in substantial conformity with its Owner's Manual. Warranty shall not apply to defects caused by
    Page 1 of 1 misuse or neglect.
    Rev. 07-03-2012 Protected under U.S. and foreign patents (see www.insteon.com) © Copyright 2012
    INSTEON, 16542 Millikan Ave., Irvine, CA 92606, 800-762-7845, www.insteon.com

    You might also like