Scribd
Upload
44 views4 pages

CCNA3 Final2

The document describes commands used to configure VLANs and inter-VLAN routing on a router. It lists commands to configure VLAN interfaces, IP addresses for each VLAN, and trunk ports to allow communication between the VLANs connected to the switch.

Uploaded by

Vladimir Oleynikov
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
44 views4 pages

CCNA3 Final2

The document describes commands used to configure VLANs and inter-VLAN routing on a router. It lists commands to configure VLAN interfaces, IP addresses for each VLAN, and trunk ports to allow communication between the VLANs connected to the switch.

Uploaded by

Vladimir Oleynikov
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 4

Top of Form

Refer to the graphic. Which of the following commands would be used on the router to provide communication between the
connected to the switch?
interface vlan 2
ip address 192.168.2.1 255.255.255.0
no shutdown
interface vlan 3
ip address 192.168.3.1 255.255.255.0
no shutdown
interface fastethernet 0/0
no shutdown
interface fastethernet 0/0.2
encapsulation dot1q 2
ip address 192.168.2.1 255.255.255.0
interface fastethernet 0/0.3
encapsulation dot1q 3
ip address 192.168.3.1 255.255.255.0
interface vlan 2
switchport mode trunk dot1q
interface vlan 3
switchport mode trunk dot11
interface fastethernet 0/0
mode trunk dot1q 2 3
ip address 192.168.2.1 255.255.255.0
   
2 Top of Form

Refer to the graphic. If the switches are new and have been cabled as shown, which switch will become the root bridge?
SC

CE

JB

JP

JN

cannot be determined from the information given


   

3 Top of Form
A switch is operating in VTP client mode. What is true about the operations that can be performed by the switch?
VLANs that are created are not included in advertisements.

It can only adopt VLAN changes advertised from a VTP server.

It advertises topology changes out all trunk ports.

It can modify existing VLANs, but can not create new ones.

It can create and modify VLANs, but can not delete existing ones.
   
4 Top of Form
Why would a network administrator choose to enable authentication for OSPF exchanges? (Choose two.)
to prevent routing information from being falsified

to reduce OSPF information exchange overhead


to assure that OSPF routing information takes priority over RIP or IGRP updates

to encrypt routing tables to prevent unauthorized viewing

to ensure that routing information comes from a valid source


   

5 Top of Form
A network administrator asked an assistant to remove several VLANs from a switch. When the assistant entered in the no
command an error was received. What was the cause of the error?
VLANs can not be deleted until all ports have been removed from the VLAN assignment.

VLANs can only be deleted by the user that created them.

VLAN 1 can not be deleted until another VLAN has been assigned its duties.

VLAN1 is the management VLAN by default and can not be deleted.

The command was not entered properly, which caused a syntax error to occur.
   
6 Top of Form
Employees of XYZ Company connect their laptop computers to the office LAN using Ethernet ports. The Cisco switches us
company network are configured with port security. At which layer of the three-layer design model do these switches opera
physical

distribution

data link

access

core
   

7 Top of Form

Refer to the graphic. What will be the result of DR elections in the network presented in the graphic using OSPF? (Choose
RTC will be DR of the 10.5.0.0/24 network.

RTD will be DR of the 10.5.0.0/24 network.

RTA will be DR of the 10.4.0.0/24 network.

RTD will be DR of the 10.4.0.0/24 network.

RTB will be DR of the 10.7.0.0/24 network.

RTD will be DR of the 10.7.0.0/24 network.


   
8 Top of Form
Which of the following statements is true when VTP is configured on a switched network that incorporates VLANs?
VTP is only compatible with the 802.1Q standard.

VTP adds to the complexity of managing a switched network.

All VTP hello packets are routed through VLAN 1 interfaces.

Changes made to the network can be communicated to all switches dynamically.


   

9 Top of Form
Which of the following tasks must be completed to configure a router interface to serve the newly added network 192.168
to advertise this network over RIP v2? (Choose three.)
RIP v2 must be configured with the network command and the IP network number for the new network.
RIP v2 must be configured with the network command and the IP host address and subnet mask for the newly activ
interface.
The router must be configured with the ip subnet-zero command so that this network can be added and advertised.

A network host address and subnet mask must be applied to the newly activated interface.

The routing protocol must be activated with the router rip and version 2 commands.

RIP v2 must be configured on the other enterprise routers with an entry for the newly added network.
   
10 Top of Form
Which layer of the hierarchical three-layer design model combines traffic from multiple IDFs?
access

backbone

distribution

core
   

11 Top of Form
A company has been assigned three Class C addresses and requires the use of supernetting in its addressing scheme. W
protocol could be used to configure the company routers to support supernetting? (Choose two.)
a classless routing protocol

a classful routing protocol

OSPF

IGRP

RIP v1
   
12 Top of Form

Refer to the graphic. What does the mode of FORWARDING mean in the spanning-tree process?
The switch is sending and receiving frames.

The switch is receiving frames, but cannot send frames.

The switch is participating in an election process.

The switch is only receiving BPDUs, not data, and is not sending any type of frames.

You might also like