EC GATE 2017 Set I Key Solution

EC, GATE-2017, SET-I www.gateforum.
com
GENERAL APTITUDE
Q. No. 1 - 5 Carry One Mark Each
1. She has a sharp tongue and it can occasionally turn _______.

(A) hurtful (B) left (C) methodical (D) vital
Answer: (A)
2. Some table are shelves. Some shelves are chairs. All chairs are benches. Which of the following
conclusion can be deduced from the preceding sentences?
(i) At least one bench is a table

(ii) At least one shelf is a bench
(iii) At least one chair is a table
(iv) All benches are chairs
(A) only (i) (B) only (ii) (C) only (ii) and (iii) (D) only (iv)
Answer: (B)
3. 40% of deaths on city roads may be attributed to drunken driving. The number of degree needed to
represent this as a slice of a pie chart is
(A) 120 (B) 144 (C) 160 (D) 212
Answer: (B)
4. In the summer, water consumption is known to decrease overall by 25%. A water Board official states
that in the summer household consumption decreases by 20%, while other consumption increases by
70%.
Which of the following statement is correct?
(A) The ratio of household to other consumption is 8/17
(B) The ratio of household to other consumption is 1/17
(C) The ratio of household to other consumption is 17/8
(D) There are errors in the official’s statement
Answer: (D)
© All rights reserved by Thinkcell Learning Solutions Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form without the written permission.
EC, GATE-2017, SET-I www.gateforum.com
5. I ________ made arrangements had I _________informed earlier.
(A) could have, been (B) would have, being

(C) had, have (D) had been, been
Answer: (A)
Q. No. 6- 10 Carry Two Marks Each
6. “If you are looking for a history of India, or for an account of the rise and fall of the British Raj, or for
the reason of the cleaving of the subcontinent into two mutually antagonistic parts and the effects this
mutilation will have in the respective section, and ultimately on Asia, you will not find it in these
pages; for though I have spent a lifetime in the country. I lived too near the seat of events, and was too
intimately associated with the actors, to get the perspective needed for the impartial recording of these
matters”.
Here, the word ‘antagonistic’ is closest in meaning to
(A) impartial (B) argumentative (C) separated (D) hostile
Answer: (D)
7. There are 3 Indians and 3 Chinese in a group of 6 people. How many subgroups of this group can we
choose so that every subgroup has at least one Indian?
(A) 56 (B) 52 (C) 48 (D) 44
Answer: (A)
8. A contour line joints locations having the same height above the mean sea level. The following is a
contour plot of a geographical region. Contour lines are shown at 25 m intervals in this plot.
The path from P to Q is best described by

(A) Up-Down-Up-Down
(B) Down-Up-Down-Up
(C) Down-Up-Down
(D) Up-Down-Up
Answer: (C)
9. Trucks (10m long) and cars (5 m long) go on a single lane bridge. There must be a gap of atleast 20 m
after each truck and a gap of atleast 15m after each car. Trucks and cars travel at a speed of 36 km/h. If
cars and trucks go alternatively, what is the maximum number of vehicles that can use the bridge in
one hour?
(A) 1440 (B) 1200 (C) 720 (D) 600
Answer: (A)
10. S, T, U, V, W, X, Y and Z are seated around a circular table. T’s neighbours are Y and V. Z is seated
third to the left of T and second to the right of S.U’sneighbours are S and Y; and T and W are not
seated opposite each other. Who is third to the left of V?
(A) X (B) W (C) U (D) T
Answer: (A)
ELECTRONICS AND COMMUNICATION ENGINEERING
Q. No. 1 to 25 Carry One Mark Each
1. The clock frequency of an 8085 microprocessor is 5 MHz. If the time required to execute an
instruction is 1.4 s, then the number of T-states needed for executing the instruction is
(A) 1 (B) 6 (C) 7 (D) 8
Answer: (C)
2. Consider a single input single output discrete-time system with x[n] as input and y[n] as output, where
the two are related as
 n x n 
 for 0  n  10
yn = 
x  n  − x  n − 1
 otherwise
Which one of the following statements is true about the system?

(A) It is causal and stable (B) It is causal but not stable
(C) It is not causal but stable (D) It is neither causal nor stable
Answer: (A)
3. Consider the following statement about the linear dependence of the real valued functions
y1 = 1, y 2 = x and y3 = x 2 , over the field of real numbers.
I. y1 , y2 and y3 are linearly independent on − 1  x  0
II. y1 , y2 and y3 are linearly dependent on 0  x  1
III. y1 , y2 and y3 are linearly independent on 0  x  1
IV. y1 , y2 and y3 are linearly dependent on − 1  x  0
Which one among the following is correct?

(A) Both I and II are true (B) Both I and III are true
(C) Both II and IV are true (D) Both III and IV are true
Answer: (B)
4. Consider the 5 × 5 matrix
1 2 3 4 5
5 1 2 3 4 

A = 4 5 1 2 3
 
3 4 5 1 2
 2 3 4 5 1 
It is given that A has only one real eigen value. Then the real eigen value of A is
(A) −2.5 (B) 0 (C) 15 (D) 25
Answer: (C)
5. The voltage of an electromagnetic wave propagating in a coaxial cable with uniform characteristic
impedance is V ( ) = e− + jt volts, where is the distance along the length of the cable in meters.
 = ( 0.1 + j40) m−1 is the complex propagation constant, and  = 2  109 rad s is the angular
frequency.Theabsolute value of the attenuation in the cable in dB/meter is __________.
Answer: (0.868)
6. A bar of Gallium Arsenide (GaAs) is doped with Silicon such that the Silicon atoms occupy Gallium
and Arsenic sites in the GaAs crystal. Which one of the following statement is true?
(A) Silicon atoms act as p-type dopants in Arsenic sites and n-type dopants in Gallium sites
(B) Silicon atoms act as n-type dopants in Arsenic sites and p-type dopants in Gallium sites
(C) Silicon atoms act as p-type dopants in Arsenic as well as Gallium sites
(D) Silicon atoms act as n-type dopants in Arsenic as well as Gallium sites
Answer: (A)
5 10 10 
7. The rank of the matrix M = 1 0 2  is
3 6 6 
(A) 0 (B) 1 (C) 2 (D) 3

Answer: (C)
8. For a narrow base PNP BJT, the excess minority carrier concentration ( nEfor emitter,
pB for base. n Cfor collector ) normalized to equilibrium minority carrier concentration ( n E0for emitter,
pB0 for base, n C0 for collector) in the quasi-neutral emitter, base and collector regions are shown below.
Which one of the following biasing modes is the transistor operating in?
105
Carrier Concentration
p B
Normalized excess
p B0
n C
n C0
0 n
E
n E0
Emitter ( P ) Base ( N) Collector ( P )
X and Y axes are not to scale
(A) Forward active (B) Saturation (C) Inverse active (D) Cutoff
Answer: (C)
9. The Miller effect in the context of a Common Emitter amplifier explains

(A) an increase in the low-frequency cutoff frequency
(B) an increase in the high-frequency cutoff frequency
(C) a decrease in the low-frequency cutoff frequency
(D) a decrease in the high-frequency cutoff frequency
Answer: (D)
10. Consider the D-Latch shown in the figure, which is transparent when its clock input CK is high and
has zero propagation delay.
TCIK
CLK1 D Q Output
CLK1 D-Latch
CLK2 CK
CLK2
TCIK 5
In the figure, the clock signal CLK1 has a 50% duty cycle and CLK2 is a one-fifth period delayed
version of CLK1.
The duty cycle at the output latch in percentage is ___________.
Answer: (30)
11. Which of the following can be pole-zero configuration of a phase-lag controller (lag compensator)?
(A) j (B) j
Pole Pole
s-plane Zero
s-plane
Zero
 
(C) j (D) j
Pole Pole
s-plane s-plane
Zero Zero


Answer: (A)
12. In the latch circuit shown, the NAND gates have non-zero, but unequal propagation delays. The
present input condition is: P = Q = ‘0’. If the input condition is changed simultaneously to P = Q = ‘1’,
the outputs X and Y are
P
(A) X = ‘1’, Y = ‘1’ X
(B) either X = ‘1’, Y = ‘0’ or X = ‘0’, Y = ‘1’
(C) either X = ‘1’, Y = ‘1’ or X = ‘0’, Y = ‘0’

Y
(D) X = ‘0’, Y = ‘0’ Q
Answer: (B)
13. Three fair cubical dice are thrown simultaneously. The probability that all three dice have the same
number of dots on the faces showing up is (up to third decimal place) ____.
Answer: (0.028)
14. A periodic signal x(t) has a trigonometric Fourier series expansion


x ( t ) = a 0 +  ( a n cos n0 t + b n sin n0 t ).
n =1
If x ( t ) = −x − ( t ) = −x ( t −  0 ) , we can conclude that
(A) an are zero for all n and bn are zero for n even
(B) an are zero for all n and bn are zero for n odd
(C) an are zero for n even and bn are zero for n odd
(D) an are zero for n odd and bn are zero for n even
Answer: (A)
15. The open loop transfer function G ( s ) =

( s + 1)
s p
( s + 2 )( s + 3)
Where p is an integer, is connected in unity feedback configuration as shown in figure.
G (s)
+
−
Given that the steady state error is zero for unit step input and is 6 for unit ramp input, the value of the
parameter p is _________.
Answer: (1)
+
16. An n − n Silicon device is fabricated with uniform and non-degenerate donor doping concentrations
−3 −3
of N D1 = 1  10 cm and N D2 = 1  10 cm corresponding to the n and n regions respectively. At
18 15 +
the operational temperature T, assume complete impurity ionization, kT/q = 25 mV, and intrinsic
−3
carrier concentration to be n i = 1  10 cm . What is the magnitude of the built-in potential of this
10
device?
(A) 0.748V (B) 0.460V (C) 0.288V (D) 0.173V
Answer: (D)
17. For the operational amplifier circuit shown, the output saturation voltages are 15V. The upper and
lower threshold voltages for the circuit are, respectively.
+
−
Vin Vout
− +
10 k
5 k
+ 3V
−
(A) +5V and − 5V (B) +7V and − 3V
(C) +3V and − 7V (D) +3V and− 3V
Answer: (B)
18. In the circuit shown, the positive angular frequency  (in radians per second) at which magnitude of

the phase difference between the voltages V1 and V2 equals radians, is __________.
4
V2
1 1H
100cos t V1
1
Answer: (1)
19. In a digital communication system, the overall pulse shape p(t) at the receiver before the sampler has
the Fourier transform P(f). If the symbols are transmitted at the rate of 2000 symbols per second, for
which of the following cases is inter symbol interference zero?
P (f )
(A) P (f ) (B)
1
1
f ( kHz ) −1.2 −0.8 0.8 1.2 f ( kHz )

−1.2 0 1.2
0
P (f )
(C) P (f ) (D)
1
1
f ( kHz )
f ( kHz ) −1.2 0 1.2
−1.2 −1 0 1 1.2
Answer: (B)
20. Consider a stable system with transfer function
sp + b1sp−1 + + bp
G (s) = q −1
s + a1s
q
+ + aq
Where b1 , ,bp and a1 , a q are real valued constants. The slope of the Bode log magnitude curve of
G(s) converges to −60 dB decade as  → . A possible pair of values for p and q is

(A) p = 0 and q = 3 (B) p = 1and q = 7
(C) p = 2 and q = 3 (D) p = 3 and q = 5
Answer: (A)
21. A good transconductance amplifier should have

(A) high input resistance and low output resistance
(B) low input resistance and high output resistance
(C) high input and output resistances
(D) low input and output resistance
Answer: (C)
22. Let ( X1 ,X2 ) be independent random variables. X1 has mean 0 and variance 1, while X2 has mean 1
and variance 4. The mutual information I ( X1;X2 ) between X1 and X2 in bits is _________.
Answer: (0)
23. Consider the following statements for continuous-time linear time invariant (LTI) systems.
I. There is no bounded input bounded output (BIBO) stable system with a pole in the right half of
the complex plane.
II. There is no causal and BIBO stable system with a pole in the right half of the complex plane.
Which one among the following is correct?
(A) Both I and II are true (B) Both I and II are not true
(C) Only I is true (D) Only II is true
Answer: (D)
24. Which one of the following statements about differential pulse code modulation (DPCM) is true?
(A) The sum of message signal sample with its prediction is quantized
(B) The message signal sample is directly quantized, and its prediction is not used
(C) The difference of message signal sample and a random signal is quantized
(D) The difference of message signal sample with its predictions is quantized
Answer: (D)
25. Consider a wireless communication link between a transmitter and a receiver located in free space,
with finite and strictly positive capacity. If the effective areas of the transmitter and the receiver
antennas, and the distance between them are all doubled, and everything else remains unchanged, the
maximum capacity of the wireless link
(A) increases by a factor of 2 (B) decrease by a factor 2
(C) remains unchanged (D) decreases by a factor of 2
Answer: (C)
Q. No. 26 to 55 Carry Two Marks Each
26. Starting with x = 1, the solution of the equation x 3 + x = 1, after two iterations of Newton-Raphson’s
method (upto two decimal places) is _________.
Answer: (0.69)
27. In binary frequency shift keying (FSK), the given signal waveform are
u 0 ( t ) = 5cos ( 20000t ) ;0  t  T, and
u1 ( t ) = 5cos ( 22000t ) ; 0  t  T,
Where T is the bit-duration interval and t is in seconds. Both u 0 ( t ) and u1 ( t ) are zero outside the
interval 0  t  T. With a matched filter (correlator) based receiver, the smallest positive value of T (in
milliseconds) required to have u 0 ( t ) and u1 ( t ) uncorrelated is
(A) 0.25ms (B) 0.5ms (C) 0.75ms (D) 1.0ms

Answer: (B)
28. For the DC analysis of the Common-Emitter amplifier shown, neglect the base current and assume that
the emitter and collector current are equal.
VCC = 12V
RC 2 k
73 k 10 F
R1 +
10 F C2
RL Vo
C1
8 k
V1 ~ 47 k R2 RE 2 k
CE
100 F
−
Given that VT = 25mV, VBE = 0.7V, and the BJT output resistance r0 is practically infinite. Under
these conditions, the midband voltage gain magnitude AV = Vo Vi V V, is ____________.
Answer: (128)
29. The figure shows an RLC circuit exited by the

sinusoidal voltage 100cos ( 3t ) volts, where t is in seconds. V1
amplitude of V2
The ratio is _________. 4 1H
amplitude of V1 5
100cos t ~ 1
V2
F
Answer: (2.6) 36
30. Which one of the following is the general solution of the first order differential equation
dy
= ( x + y − 1) , where x, y are real?
2
dx
(A) y = 1 + x + tan −1 ( x + c ) , (B) y = 1 + x + tan ( x + c ) ,
where c is a constant where c is a constant
(C) y = 1 − x + tan −1 ( x + c ) , (D) y = 1 − x + tan ( x + c ) ,

where c is a constant where c is a constant
Answer: (D)
31. A linear time invariant (LTI) system with the transfer function
k ( s2 + 2s + 2 )
G (s) =
(s 2
− 3s + 2 )
is connected in unity feedback configuration as shown in the figure.
G (s )
+ −
For the closed loop system shown, the root locus for 0  k   intersects the imaginary axis for k =
1.5. The closed loop system is stable for
(A) k  1.5 (B) 1  k  1.5
(D) 0  k 1 (D) no positive value of k
Answer: (A)
32. Let I =  ( 2z dx + 2y dy + 2x dz ) where x, y, z are real, and let C be the straight line segment from
C
point A : ( 0,2,1) to point B: ( 4,1, −1). The value of I is _________.
Answer: (–11)
33. As shown, two Silicon (Si) abrupt p-n junction diodes are fabricated with uniform donor doping
−3 −3
concentration of N D1 = 10 cm and N D2 = 10 cm in the n-regions of the diodes, and uniform acceptor
14 16
−3 −3
doping concentration of N A1 = 10 cm and N A2 = 10 cm in the p-regions of the diodes, respectively.
14 16
p n p n
1014 1014 1016 1016

cm−3 cm−3 cm−3 cm−3
C1 C2
Diode1 Diode 2
Assuming that the reverse bias voltage is >> built-in potentials of the diodes, the ratio C2 C1 of their
reverse bias capacitances for the same applied reverse bias, is __________.
Answer: (10)
34. An optical fiber is kept along the ẑ direction. The refractive indices for the electric fields along x̂ and
ŷ directions in the fiber are n x = 1.5000 and n y = 1.5001, respectively (n x  n y due to the
imperfection in the fiber cross-section). The free space wavelength of a light wave propagating in the
fiber is 1.5m. If the light wave is circularly polarized at the input of the fiber, the minimum
propagation distance after which it becomes linearly polarized, in centimeter, is ___________.
Answer: (0.375)
35. Two discrete-time signals x[n] and h[n] are both non-zero for n = 0, 1, 2 and are zero otherwise. It is
given that
x 0 = 1, x 1 = 2, x 2 = 1, h 0 = 1.
Let y[n] be the linear convolution of x[n] and h[n]. Given that y[1] = 3 and y[2] = 4, the value of the
expression (10y 3 + y  4) is _________.
Answer: (31)
36. Which one of the following options correctly describes the locations of the roots of the equation
s4 + s2 + 1 = 0 on the complex plane?
(A) Four left half plane (LHP) roots
(B) One right half plane (RHP) root, one LHP root and two roots on the imaginary axis
(C) Two RHP roots and two LHP roots
(D) All four roots are on the imaginary axis
Answer: (C)
37. The dependence of drift velocity of electrons on electric field in a semiconductor is shown below.
Drift velocity ( cm s )
constant
107
linear
0 5 105 Electric field ( V cm )
The semiconductor has a uniform electron concentration of n = 11016 cm−3 and electronic charge
q = 1.6  10−19 C. If a bias of 5V is applied across a 1 m region of this semiconductor, the resulting
current density in this region, in kA/cm2, is _________.
Answer: (1.6)
38. For the circuit shown, assume that the NMOS transistor is in saturation.
VDD = 8V
1k
R1 RD
3 M ID
R2 RS 1k
5 M
W
Its threshold voltage Vtn = 1V and its transconductance parameter  n Cox   = 1mA V 2 . Neglect
 L
channel length modulation and body bias effects. Under these conditions, the drain current ID in mA is
___________.
Answer: (2)
39. Let X(t) be a wide sense stationary random process with the power spectral density S X(f) as shown in
Figure (a), where f is in Hertz (Hz). The random process X(t) is input to an ideal low pass filter with
frequency response
 1
1, f  2 Hz
H (f ) = 
0, f  1 Hz
 2
As shown in Figure (b). The output of the lowpass filter is Y ( t ) .
SX ( f )
ideal lowpass Y(t)
filter h ( t )
X(t)
exp ( − f ) cutoff = 1 2 Hz
f
0
(a ) (b)
Let E be the expectation operator and consider the following statements.

I. E ( X ( t )) = E ( Y ( t ))
II. E ( X2 ( t ) ) = E ( Y 2 ( t ) )
III. E ( Y2 ( t ) ) = 2
Select the correct option:
(A) only I is true (B) only II and III are true
(C) only I and II are true (D) only I and III are true
Answer: (A)
40. As shown a uniformly doped Silicon (Si) bar of length L = 0.1 m with a donor concentration
N D = 1016 cm −3 is illuminated at x = 0 such that electron and hole pairs are generated at the rate of
 x −3 −1
G L = G L0 1 −  ,0  x  L, where G L0 = 10 cm s . Hole lifetime is 10−4 s, electronic charge
17
 L 
q = 1.6  10−19 C, hole diffusion coefficient Dp = 100 cm2 s and low level injection condition prevails.
Light
Si ( ND = 1016 cm−3 )
x=0 L = 0.1 m
Assuming a linearly decaying steady state excess hole concentration that goes to 0 at x = L, the
magnitude of the diffusion current density at x = L/2, in A/cm2, is _________.
Answer: (16)
41. The Nyquist plot of the transfer function

k
G (s) =
(s + 2s + 2) ( s + 2)
2
does not encircle the point(-1+j0) for k = 10 but does encircle the point(-1+j0) for k =100.
Then the closed loop system (having unity gain feedback) is
(A) stable for k = 10 and stable for k = 100
(B) stable for k = 10 and unstable for k = 100
(C) unstable for k = 10 and stable for k =100
(D) unstable for k = 10 and unstable for k = 100
Answer: (B)
42. In the figure shown, the npn transistor acts as a switch

+5V
Vin ( t )
4.8 k
2V 12 k
+
T
0V Vin ( t )
−
t ( in seconds )
For the input Vin ( t ) as shown in the figure, the transistor switches between the cut-off and saturation
regions of operation, when T is large. Assume collector-to-emitter voltage saturation VCE(sat ) = 0.2V
and base-to-emitter voltage VBE = 0.7V. The minimum value of the common-base current gain (  ) of
the transistor for the switching should be _______.
Answer: (0.9)
43. A three dimensional region R of finite volume is described by

x 2 + y 2  z3 ;0  z  1,
Where x, y, z are real. The volume of R (up to two decimal places) is ___________.
Answer: (0.79)
44. The expression for an electric field in free space is
( )
E = E0 x + y + j2z e− j(t −kx + ky)
Where x, y, z represent the spatial coordinates, t represents time, and , k are constants.
This electric field
(A) Does not represent a plane wave
(B) represents a circularly polarized plane wave propagating normal to the z-axis.
(C) represents an elliptically polarized plane wave propagating along the x-y plane.
(D) represents a linearly polarized plane wave.
Answer: (C)
45. A finite state machine (FSM) is implemented using the D flip-flops A and B, and logic gates, as shown
in the figure below. The four possible states of the FSM are QA QB = 00,01,10 and 11.
QA
D Q D Q QB
A B
X IN Q
CK Q CK
CLK
Assume that X1N is held at a constant logic level throughout the operation of the FSM. When the FSM
is initialized to the state QA QB = 00 and clocked, after a few clock cycles, it starts cycling through
(A) all of the four possible states if X1N = 1
(B) three of the four possible states if X1N = 0
(C) only two of the four possible states if X IN = 1
(D) only two of the four possible states if X1N = 0

Answer: (D)
46. Let x(t) be a continuous time periodic signal with fundamental period T = 1 seconds. Let a k  be the
complex. Fourier series coefficients of x(t), where k is integer valued. Consider the following
statements about x(3t).
I. The complex Fourier series coefficient of x(3t) are [ak] where k is integer valued
II. The complex Fourier series coefficient of x(3t) are [3ak] where k is integer valued
III. The fundamental angular frequency of x(3t) is 6 rad/s
For the three statements above which one of the following is correct?
(A) only II and III are true (B) only I and III are true
(C) only III is true (D) only I is true
Answer: (B)
47. A 4-bit shift register circuit configured for right-shift operation, i.e, Din → A, A → B, B → C, C → D,
is shown.
Din A B C D
Clock
If the present state of the shift register is ABCD = 1101, the number of clock cycles required to reach
the state ABCD = 1111 is _________.
Answer: (10)
Let f ( x ) = e x + x for real x. From among the following, choose the Taylor series
2
48.
approximation of f(x) around x = 0, which includes all powers of x less than or equal to 3.
3
(A) 1 + x + x2 + x3 (B) 1 + x + x 2 + x3
2
3 7
(C) 1 + x + x 2 + x3 (D) 1 + x + 3x 2 + 7x3
2 6
Answer: (C)
49. The following FIVE instructions were executed on an 8085 microprocessor.

MVI A, 33H
MVI B, 78H
ADD B
CMA
ANI 32H
The Accumulator value immediately after the execution of the fifth instruction is
(A) 00H (B) 10H (C) 11H (D) 32H
Answer: (B)
50. In the circuit shown, the voltage V1N ( t ) is described by:
1 I
 0, for t  0
VIN =  +
15 volts for t  0
VIN (t) 1H 2H
Where t is in seconds. The time (in seconds) at which the current I in the circuit will reach the value 2
Amperes is ___________.
Answer: (0.34)
51. A half wavelength dipole is kept in the x-y plane and oriented along 45o from the x-axis. Determine
the direction of null in the radiation pattern for 0    . Here the angle  ( 0    ) is measured
from the z-axis, and the angle  ( 0    2) is measured from the x-axis in the x-y plane.
(A)  = 90o ,  = 45o (B)  = 45o ,  = 90o
(C)  = 90o ,  = 135o (D)  = 45o ,  = 135o

Answer: (A)
52. The amplifier circuit shown in the figure is implemented using a compensated operational amplifier
(op-amp), and has an open-loop voltage gain, A o = 10 V V and an open-loop cut-off frequency
5
f c = 8Hz.
R 2 = 79k
R1 = 1k
−
Vo
+
V1 ~
The voltage gain of the amplifier at 15 kHz, in V/V is __________.
Answer: (44.3)
53. Let h[n] be the impulse response of a discrete-time linear time invariant (LTI) filter. The impulse
response is given by
1 1 1
h 0 = ; h 1 = ; h  2 = ; and h n  = 0 for n  0 and n  2.
3 3 3
Let H ( ) be the discrete-time Fourier system transform (DTFT) of h[n], where  is the normalized
angular frequency in radians. Given that H ( 0 ) = 0 and 0  0  , the value of 0 (in radians) is
equal to __________.
Answer: (2.094)
54. Which one of the following gives the simplified sum of products expression for the Boolean function
F = m0 + m2 + m3 + m5 , where m0 ,m2 ,m3 and m 5 are minterms corresponding to the inputs A, B and
C with A as the MSB and C as the LSB?
(A) AB + ABC + ABC (B) AC + AB + ABC
(C) AC + AB + ABC (D) ABC + AC + ABC
Answer: (B)
55. A continuous time signal x ( t ) = 4cos ( 200t ) + 8cos ( 400t ) , where t is in seconds, is the input to a
linear time invariant (LTI) filter with the impulse response

 2sin ( 300t )
 , t0
h(t) =  t
 t =0
 600,
Let y(t) be the output of this filter. The maximum value of y ( t ) is ________.
Answer: (B)

EC GATE 2017 Set I Key Solution

Uploaded by

Copyright:

Available Formats

EC GATE 2017 Set I Key Solution

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

EC GATE 2017 Set I Key Solution

Uploaded by

Copyright:

Available Formats

EC, GATE-2017, SET-I www.gateforum.

1. She has a sharp tongue and it can occasionally turn _______.

(i) At least one bench is a table

5. I ________ made arrangements had I _________informed earlier.

(A) could have, been (B) would have, being

Q. No. 6- 10 Carry Two Marks Each

The path from P to Q is best described by

ELECTRONICS AND COMMUNICATION ENGINEERING

Q. No. 1 to 25 Carry One Mark Each

Which one of the following statements is true about the system?

II. y1 , y2 and y3 are linearly dependent on 0  x  1

III. y1 , y2 and y3 are linearly independent on 0  x  1

IV. y1 , y2 and y3 are linearly dependent on − 1  x  0

Which one among the following is correct?

4. Consider the 5 × 5 matrix

(A) 0 (B) 1 (C) 2 (D) 3

9. The Miller effect in the context of a Common Emitter amplifier explains

(B) either X = ‘1’, Y = ‘0’ or X = ‘0’, Y = ‘1’

(C) either X = ‘1’, Y = ‘1’ or X = ‘0’, Y = ‘0’

14. A periodic signal x(t) has a trigonometric Fourier series expansion

If x ( t ) = −x − ( t ) = −x ( t −  0 ) , we can conclude that

15. The open loop transfer function G ( s ) =

f ( kHz ) −1.2 −0.8 0.8 1.2 f ( kHz )

20. Consider a stable system with transfer function

G(s) converges to −60 dB decade as  → . A possible pair of values for p and q is

21. A good transconductance amplifier should have

Q. No. 26 to 55 Carry Two Marks Each

(A) 0.25ms (B) 0.5ms (C) 0.75ms (D) 1.0ms

these conditions, the midband voltage gain magnitude AV = Vo Vi V V, is ____________.

29. The figure shows an RLC circuit exited by the

(C) y = 1 − x + tan −1 ( x + c ) , (D) y = 1 − x + tan ( x + c ) ,

is connected in unity feedback configuration as shown in the figure.

point A : ( 0,2,1) to point B: ( 4,1, −1). The value of I is _________.

1014 1014 1016 1016

0 5 105 Electric field ( V cm )

Let E be the expectation operator and consider the following statements.

41. The Nyquist plot of the transfer function

42. In the figure shown, the npn transistor acts as a switch

43. A three dimensional region R of finite volume is described by

44. The expression for an electric field in free space is

(A) all of the four possible states if X1N = 1

(B) three of the four possible states if X1N = 0

(C) only two of the four possible states if X IN = 1

(D) only two of the four possible states if X1N = 0

49. The following FIVE instructions were executed on an 8085 microprocessor.

50. In the circuit shown, the voltage V1N ( t ) is described by:

(A)  = 90o ,  = 45o (B)  = 45o ,  = 90o

(C)  = 90o ,  = 135o (D)  = 45o ,  = 135o

The voltage gain of the amplifier at 15 kHz, in V/V is __________.

linear time invariant (LTI) filter with the impulse response

You might also like

5. I made arrangements had I _informed earlier.