International Journal of Advances in Engineering Research http://www.ijaer.

com

(IJAER) 2015, Vol. No. 10, Issue No. VI, December e-ISSN: 2231-5152/ p-ISSN: 2454-1796

CALCULATION OF COOLING LOAD FOR MUSHROOM

CULTIVATION
*S. Daniel Selvakumar, *R. Immanual, **Dr. S. Rajakumar
*PG student: Department of Mechanical Engineering,
Regional centre, Anna university Tirunelveli Region Tirunelveli, India
** Assistant Professor: Department of Mechanical Engineering,
Regional centre, Anna university Tirunelveli Region,Tirunelveli, India

ABSTRACT

In this paper the thermal comfort condition for mushroom cultivation was studied. In addition to this the
cooling load needed for bring that thermal comfort condition was calculated. Mushroom cultivation was
done by so many peoples in the hot and dry climatic places. In the cold places the yield of mushroom was
more compared with the cold climatic places this is due to thermal comfort condition needed for
mushroom cultivation. The solution for even yield in dry and cold climatic condition is to bring the thermal
comfort condition at dry places by means of a refrigeration system. To design a refrigeration system
cooling load calculation is necessary. So a prototype model for refrigeration system geometry for
mushroom cultivation was developed and its necessary cooling load was calculated.
Keywords: cooling load; mushroom cultivation; Refrigeration system; Thermal comfort.

INTRODUCTION

During Solar heat conversion, waste heat dissipation is a huge factor. To avoid this problem Four
pilot installations between 7 kW and 90 kW nominal cooling capacity were equipped with latent
heat storages between 80 kWh and 240 kWh energy content. It results in a seasonal energy
efficiency ratio (SEER) for cooling up to 11.4. Furthermore simulation results under different
climatic conditions indicate raising efficiency up to 64% compared to a system with solely dry re-
cooling.[1] Many factors can affect the operating performances and the design of the indirect air
cooling system of power plant. A study has been carried out by developing a physic mathematical
model describe the thermo flow characteristics of air cooling tower for indirect air cooling
system.VC ++ is used to develop a program for the indirect air-cooled tower optimization. By this
program better tower structure is achieved which is used to conduct thermal analysis of the
influences of ambient temperature, wind speed, and saturated exhaust flow rate on back pressure
of turbine.[2] A closed loop thermal cycle with loop thermal cycle containing cylindrical heat
pipes integrated within a roof-mounted circular wind tower is used to achieve internal comfort.
By using inlet wind speeds varying from 1 m/s to 5 m/s, the results of the study showed that the
proposed cooling system was capable of meeting the regulatory fresh air intake requirements per
occupant of 10L/s. In addition, the results showed that a passive cooling capacity ranging between
6K and 15K depending on the operating configuration. [3] TPV(Thermal Photo Voltaic) systems

196

INTERNATIONAL JOURNAL OF ADVANCES IN ENGINEERING RESEARCH

International Journal of Advances in Engineering Research http://www.ijaer.com

(IJAER) 2015, Vol. No. 10, Issue No. VI, December e-ISSN: 2231-5152/ p-ISSN: 2454-1796

are increased by three developments like diffused junction GaSb cell that responds out to 1.8
microns producing over 1 W/cm2 electric given an IR emitter temperature of 1200 C. High power
density along with a simple diffused junction cell makes an array cost of $0.5 per Watt possible.
IR emitters and filters that put 75% of the radiant energy in the cell convertible band. Ceramic
radiant tube burners that operate at up to 1250 C. Herein, we describe a 1.5 kW TPV generator /
furnace incorporating these new features. This TPV generator / furnace is designed to replace the
residential furnace for combined heat and power (CHP) for the home [4]. An investigation is
carried out to check the potential of producing liquid spawn of an edible mushroom, Pleurotus
pulmonary’s (grey oyster) by submerged fermentation in a 2-L stirred-tank bioreactor under
controlled conditions also to evaluate its ability to colonize rubber wood sawdust substrate for
sporophore production. It contains 20 g L−1 of brown sugar, 4 g L−1 of rice bran, 4 g L−1 of malt
extract, and 4 g L−1 of yeast extract (BRMY) with initial pH of 5.5 and incubated at 28◦C with
agitation speed of 250 rpm and oxygen partial pressure of 30–40%. Maximum P. pulmonarius dry
biomass production of 11.72 ± 5.26 g L−1 was achieved after 3 days of fermentation. It produces
higher yield of sporophores compared to normal used grain spawn. [5] To recycle agro-industrial
wastes into food production a new species named genus Gymnopilus is used to determine the
optimal condition needed to cultivate G. pompanos, to evaluate its biological efficiency and to
determine the biodegradation of substrate. Strain ICFC 748/12 produces the highest biological
efficiency on Populus sawdust reaching a mean of 70.67%. G. pampeanus has a strong capacity to
degrade Eucalyptus and Populus. This mushroom has the ability to decompose cellulose and to
decaylignin, thus being white rot fungi [6].

CFC-12 is replaced in order to investigate behavior of R134a refrigerant. This includes

performance and efficiency variations when it replaces R12 in an existing system as well as
changes involved in maintaining the system charged with R134a[7]. AIRCOND a system
composed of three sub systems: the heating loop, the ejector cycle and the cold storage-air
handling units: heating loop is composed of a solar array of 60 square meters evacuated tube solar
collectors; installed at a tilt angle of 45° and facing to south, a 3000 L tank is used as hot water
storage in order to cover energy by the ejector cycle. The cold water produced by the ejector cycle
then transferred in a 900L cold storage tank filled with 800L micro-encapsulated phase change
material (MEPCM) for cold storage designed to meet dynamic cooling load. This study is carried
out to achieve air-conditioning in Mediterranean countries. [8]

DESIGN OF PROTOTYPE FOR MUSHROOM CULTIVATION

For Mushroom cultivation, paddy straw and mushroom seeds packed in a polyethene packet,
which is normally a circular shape with 20 cm diameter and 30 cm height. In the prototype for
cultivation we have to design a box with four mushroom cultivation pockets. Therefore, the box
size is 1-meter width 1-meter length and 2-meter height. This model was created using PRO-E
software. The door is used with the gap of 50 cm*50 cm square shape. The box is made up of
timber.

197

INTERNATIONAL JOURNAL OF ADVANCES IN ENGINEERING RESEARCH

International Journal of Advances in Engineering Research http://www.ijaer.com

(IJAER) 2015, Vol. No. 10, Issue No. VI, December e-ISSN: 2231-5152/ p-ISSN: 2454-1796

Figure 1

THERMAL COMFORT CONDITION FOR PLEUROTUS SPP.

In This paper the cooling load calculation is based on the pleurotus spp mushrooms here its
thermal comfort condition is given,
R.H = 85-92%
Air Temperature = 60-64 F
CO2 = less than 600 ppm.
Light = 2000 lux/hour
Flush Interval = 10 days

COOLING LOAD CALCULATION

Under the steady state approach which does not account the effect or effect of heat capacity of
building materials. The heat balance of room air
Q total = Q c + Qs + Q i +Q v + Q w
INTERIOR LOADING (Q i)
Qi = [no of people × heat output rate] + [rated wastage of lamps × use
factor ×allowance factor] + [heat evolved per kg of mushroom] × (kg of mushroom)
= [1*200] + [20*1*1.25] + [6490 kg]
Qi = 225.15 watts
QVENTILATION
Qv = ρ× V r × C ×ΔT
Vr = N ×V / 3600
N = 6 per hour
V = 2m3
Vr = (6 * 2 m 3)/3600
= 3.3 * 10-3
Qv = 1.2 * 1005 * 3.3 * 10-3 * 23

198

INTERNATIONAL JOURNAL OF ADVANCES IN ENGINEERING RESEARCH

International Journal of Advances in Engineering Research http://www.ijaer.com

(IJAER) 2015, Vol. No. 10, Issue No. VI, December e-ISSN: 2231-5152/ p-ISSN: 2454-1796

Qv = 91.5354 watts
The door infiltration for a 0.5 m swinging door is V r = 0.05 m3/sec
Q vd = 0.05 * 1.2 * 1005 * 23
= 1386.9 watts
Qv = 1386.9 + 91.5354
Qv = 1478.4354

QS - SOLAR HEAT GAIN

The solar gain through transparent elements can be written as
Qs = As i=1Σm Ai δqi Zi
Here, m=0, there is no transparent element
Qs = 0
Nc
Qc = i=1Σ Ai Ui ΔTi
Here, we used wood. So a=0.
In Solar temperature and for vertical wall ΔR = 0, for vertical wall Tso=To
Qc for 4 vertical walls is 303.4252 watts
For 4 walls,
= 4 * 303.4252
= 1213.7008 watts
For bottom,
= 1213.7008 + 303.4252
= 1517.126
For roof,
ΔR = 63 w/m2
T so = Tso+(αST/ho)-(Σ ΔR/ho)
ho = 34.0 w/m2
Σ = 0.70 for brown color of top
T so = To-((0.70*63)/34)
= 38-1.2970
T so = 36.70 ⁰C
Q croof = 2m2 * 6.5962 * (36.70-15)
= 286.27508 watts
= 1517.126 + 286.27508
Qc = 1803.40 watts
Total Cooling Load
Qc = 1803.403 watts
Qs = 0
Qi = 225.15 watts
Qr = 1478.4354 watts
Q total = Qc + Qs + Qi +Qv + Qw

If water is not considered and Door opening is not considered.

199

INTERNATIONAL JOURNAL OF ADVANCES IN ENGINEERING RESEARCH

International Journal of Advances in Engineering Research http://www.ijaer.com

(IJAER) 2015, Vol. No. 10, Issue No. VI, December e-ISSN: 2231-5152/ p-ISSN: 2454-1796

Qc = 1803.403 watts
Qs = 0
Qi = 225.15 watts
Qr = 91.5359 watts
Q total = 2120.0884 watts
= 2.120 K watts
= 2.120 Kw/2.8
= 0.75 tons of cooling capacity required
The 0.75 tons of cooling capacity required to meet the thermal comfort condition for mushroom
cultivation in dry places like Tirunelveli district.

CONCLUSIONS

Proto type of small refrigeration system geometry for mushroom cultivation was developed. And
its required cooling load was developed under the environmental condition of Tirunelveli in
Tamilnadu at India. This cooling load calculation is useful for those who want to make a
refrigeration system for mushroom cultivation In the future work Refrigeration system for
mushroom cultivation using vapor compression and vapor absorption system will be analyzed. If
use the refrigeration system for mushroom cultivation based on this cooling load, calculation will
increase the yield in the dry places also.

NOMENCLATURE

fo = outside film or surface conductance

fi = inside film or surface conductance
A = outside area of wall
to = outside air temperature
ti = inside air temperature
x = thickness of wall
K = thermal conductivity for the material of the wall
U = overall co-efficient of heat transmission of the wall
ΔT = Temp diff between inside and outside air(k)
A = Surface area m2
U = Thermal transmittance (w/m2.k)
K = thermal conductivity
A = Surface Area
ρ = density of air (kg/m3)
Vr = ventilation rate (m3/sec)
C = specific heat of air (J/kg-k)
N = no of air exchanges per hour
V = volume of the room
As = mean absorbtivity of the space

200

INTERNATIONAL JOURNAL OF ADVANCES IN ENGINEERING RESEARCH

International Journal of Advances in Engineering Research http://www.ijaer.com

(IJAER) 2015, Vol. No. 10, Issue No. VI, December e-ISSN: 2231-5152/ p-ISSN: 2454-1796

Ai = area of the ith transparent element

δqi = daily average value of solar radiation
Zi = transmissivity of ith transparent element
M = no of transparent element
i = building element
Nc = no of components
To = daily average value of nearly ambient temperature(K)
a = absorption of the surface for solar radiation
ST = daily average value of solar radiation incident of the surface (w/m2)
ho = outside heat transfer coefficient

REFERENCES

1. Martin Helm, Kilian Hagel, Werner Pfeffer, Stefan Hiebler, “Solar heating and cooling system
with absorption chiller and latent heat storage - A research project summary” , Christian
Schweigler11Bavarian Center for Applied Energy Research (ZAE Bayern), Walther-Meissner-
Strasse 6,D-85748 Garching, Germany
2. Xinming Xi, Lei Yang, Yanan He, Lijun Yang, Xiaoze Du “Optimal design of large scale dry
cooling tower with consideration of off-design operation” Key Laboratory of Condition
Monitoring and Control for Power Plant Equipment
3. Hassam Nasarullah Chaudhrya, n, John Kaiser Calautitb, Ben Richard Hughesba
Computational Analysis of a wind tower assisted “passive cooling technology for the built
environment School of Energy”, Geoscience, Infrastructure and Society,Heriot-Watt University,
P.O.Box: 294345, Dubai, United Arab Emirates b Department of Mechanical Engineering,
University of Sheffield, Sheffield S102TN, United Kingdom
4. Lewis M. Fraas, James E. Avery, Han Xiang Huang JX Crystals Inc.,Thermophotovoltaics:
heat and electric power from low bandgap “solar” cells around gas fired radiant tube burners 1105
12th ave nw, suite A2, Issaquah, WA 98027
5. Rozila Ismailb, Norjuliza Mohd Khir Joharia, Production of liquid spawn of an edible grey
oyster mushroom,Pleurotus pulmonarius (Fr.) Quél by submerged fermentation andsporophore
yield on rubber wood sawdust Noorlidah AbdullahaM.S.M. AnnuarbaMushroom Research
Centre, Institute of Biological Sciences, Faculty of Science, University of Malaya, 50603 Kuala
Lumpur, MalaysiabInstitute of Biological Sciences, Faculty of Science, University of Malaya,
50603 Kuala Lumpur, Malaysiaa
6. Cultivation requirements and substrate degradation of the ediblemushroom Gymnopilus
pampeanus—A novel species for mushroomcultivation María Belén Colavolpe, Edgardo
AlbertóLab. of Mycology and Mushroom Cultivation, Instituto de Investigaciones
Biotecnológicas-Instituto Tecnológico de Chascomús (IIB-INTECH), UniversidadNacional de

201

INTERNATIONAL JOURNAL OF ADVANCES IN ENGINEERING RESEARCH

International Journal of Advances in Engineering Research http://www.ijaer.com

(IJAER) 2015, Vol. No. 10, Issue No. VI, December e-ISSN: 2231-5152/ p-ISSN: 2454-1796

San Martín (UNSAM), Consejo Nacional de Investigaciones Científicas y Técnicas (CONICET),

CC 164, 7130 Chascomús, Buenos Aires, Argentinaa
7. K. Nagalakshmi1, G. Marurhiprasad Yadav”The Design and Performance Analysis of
Refrigeration System Using R12 & R134a Refrigerants” Mechanical engineer at St.Jhons
College of Engg &Technology, Yemmiganur-518360, A. P, India. 2. Associate professor,
Department of Mechanical engineering, St.Jhons College of Engg &Technology, Yemmiganur-
518360, A. P, India.
8. Yosr Allouchea, Chiheb Boudena, and Saffa Riffatb A solar-driven ejector refrigeration system
for Mediterranean climate:Experience improvement and new results performed aUniversity Tunis
El Manar, Energy, buildings and Solar systems laboratory, National Engineering school of Tunis,
B.P.37 le Belvédère 1002 Tunis, Tunisia b Department of Built Environment, University of
Nottingham, University Park, NG7 2RD, UK

202

INTERNATIONAL JOURNAL OF ADVANCES IN ENGINEERING RESEARCH