0% found this document useful (0 votes)
66 views7 pages

Unit Eight Homework Solutions, November 2, 2010: M KG M KG M KG M C V C V C V V X

1. The radiator contains superheated steam that cools from 150°C to 40°C at constant volume. This results in an entropy decrease of -0.132 kJ/K as heat is transferred out of the system. 2. A tank contains 2 kg of a saturated liquid-vapor mixture that is vaporized. This constant volume process results in an entropy increase of 8.10 kJ/K. 3. Refrigerant-134a is cooled from 100°F to 50°F at constant pressure, changing from a mixed state to a compressed liquid. This results in an entropy decrease of -0.3264 Btu/R.
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
66 views7 pages

Unit Eight Homework Solutions, November 2, 2010: M KG M KG M KG M C V C V C V V X

1. The radiator contains superheated steam that cools from 150°C to 40°C at constant volume. This results in an entropy decrease of -0.132 kJ/K as heat is transferred out of the system. 2. A tank contains 2 kg of a saturated liquid-vapor mixture that is vaporized. This constant volume process results in an entropy increase of 8.10 kJ/K. 3. Refrigerant-134a is cooled from 100°F to 50°F at constant pressure, changing from a mixed state to a compressed liquid. This results in an entropy decrease of -0.3264 Btu/R.
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 7

College of Engineering and Computer Science

Mechanical Engineering Department


Mechanical Engineering 370
Thermodynamics
Fall 2010 Course Number: 14319
Instructor: Larry Caretto

Unit Eight Homework Solutions, November 2, 2010


1 The radiator of a steam heating system has a volume of 20 L and is filled with superheated water at
vapor at 200 kPa and 150oC. At this moment both the inlet and exit valves to the radiator are closed.
After a while the temperature of the steam drops to 40oC as a result of heat transfer to the room air.
Determine the entropy change of the steam during this process in kJ/K.

If we assume that the radiator does not expand or contract significantly with the temperature
change, we have is a constant volume process. We can find the entropy change from the initial
state, where we are given the temperature and pressure and the final state where we know the
temperature and we also know that the specific volume will be the same as it is at the initial state.
We can also use the information on the radiator volume to find the system mass.
At the initial state of 200 kPa and 150oC, we find the following properties from Table A-6 on page
920: v1 = 0.95986 m3/kg and s1 = 7.2810 kJ/kg∙K. From Table A-4 on page 916, we see that, at
the final temperature T2 = 40oC, the specific volume, v2 = v1 is between vf(40oC) = 0.001008 m3/kg
and vg(40oC) = 19.515 m3/kg. Thus the final state is in the mixed region. We find the final quality
from the following equation.
3 3
v2  v f (40 C )
o 0.95986 m  0.001008 m
kg kg
x2    0.04913
v g (40 C )  v f ( 40 C )
o o
19.515 m
3
 0.001008 m
3

kg kg
We can then use this quality to find the final entropy.
0.5724 kJ  7.6832 kJ  0.9499 kJ
s 2  s f ( 40 o C )  x 2 s fg ( 40 o C )   (0.04913)  
kg  K  kg  K  kg  K
To find the total entropy change we have to find the system mass. We can find this from the
radiator volume and the initial specific volume.

m3
 20 L 
V 1000 L
m   0.02084 kg
v1 0.95986 m 3
kg
 0.9499 kJ 7.2810 kJ 
S  m s 2  s1    0.02084 kg    
 kg  K kg  K  = –0.132 kJ/K

Note that we can have a negative entropy change and still satisfy the second law inequality that
dS ≥ dQ/T because the heat transfer is negative. (We did not actually compute Q, but we know
that heat has to leave the system to change the state from a vapor at 150 oC to a mixture of liquid
and vapor at 40oC.)

Jacaranda (Engineering) 3519 Mail Code Phone: 818.677.6448


E-mail: [email protected] 8348 Fax: 818.677.7062
2 A well insulated rigid tank contains 2 kg of a saturated liquid-vapor mixture of water at 100 kPa.
Initially, three quarters of the mass is in the liquid phase. An electrical resistance heater placed in
the tank is now turned on and kept on until all the liquid in the tank is vaporized. Determine the
entropy change of the steam during this process.

In this case the initial state is a pressure of 100 kPa and a quality of 0.25. Because it is a rigid
tank, with a fixed mass, the final state has the same specific volume as the initial state. From
Table A-5 on page 918, we find the properties of the saturated liquid and vapor states at 100 kPa
and use these to compute the initial specific volume and entropy. (Note that ¾ of the mass in the
liquid state is equivalent to a quality of 25%.)

1.3028 kJ  6.0562 kJ  2.8168 kJ


s1  s f (100 kPa )  x1 s fg (100 kPa )   (0.25)  
kg  K  kg  K  kg  K

v1  v f (100 kPa )  x1  v g (100 kPa )  v f (100 kPa ) 


0.001043 m 3

kg
 1.6941 m 3 0.001043 m 3  0.4243 m 3
(0.25)   
 kg kg  kg

Since we are told that the final state is a saturated vapor and we reasoned that this is a constant
volume process, we have to find the final state as the saturated vapor state where the
temperature (or pressure) is such that vg = v1 = 0.4243 m3/kg. Looking at the vg data in Table A-4,
we see that this final state lies between a temperature of 145 oC where vg = 0.44600 m3/kg, and
150oC, where vg = 0.39248 m3/kg. We can interpolate between these two specific volumes and
the corresponding values of sg to find the final entropy. This interpolation gives the following
result.

s g (150o C )  s g (145o C )
s2  s g (145o C ) 
v g (150 C )  v g
o o
(145 C )
v 2 
 v g (145o C ) 

6.8371 kJ 6.8827 kJ

6.8827 kJ kg  K kg  K  0.4243 m 3 0.44600 m 3  6.8649 kJ
    
kg  K 0.39248 m 3
0.44600 m 3  kg kg  kg  K

kg kg
We can now compute the entropy change.

 6.8649 kJ 2.8168 kJ 
S  m s 2  s1    2 kg    
 kg  K kg  K  = 8.10 kJ/K

3 A piston-cylinder device contains 2 lbm of refrigerant-134a at 120 psia and 100oF. The refrigerant is
now cooled at constant pressure until it exists as a liquid at 50oF. Determine the entropy change of
the refrigerant during this process.

At the initial state of 120 psia and 100oF, we find the entropy s1 = 0.22362 Btu/lbm∙ from Table A-
13E on page 981. Since the process occurs at constant pressure, the final pressure equals the
initial pressure of 120 psia. At this 120 psia and the final temperature of 50 oF, we have a
compressed liquid because the temperature of 50oF is below the saturation temperature at 120
psia, which is 90.49oF. Here we make the approximation that the entropy of the liquid state
equals the entropy of the saturated liquid at the temperature of 50 oF. From Table A-11E on page
978, we find this entropy to be 0.06039 Btu/lb m∙R. Hence we compute the entropy change as
follows.

Jacaranda (Engineering) 3519 Mail Code Phone: 818.677.6448


E-mail: [email protected] 8348 Fax: 818.677.7062
 0.06039 Btu 0.22362 Btu 
S  m s 2  s1    2 lbm    
 lbm  R lbm  R 
= –0.3264 Btu/R

This is another example of a negative entropy change that presumably satisfies the second law (dS ≥ dQ/T)
because dQ < 0 for cooling.)

4 An insulated piston-cylinder device contains 0.05 m3 of saturated refrigerant 134a vapor at 0.8 MPa
pressure. The refrigerant is now allowed to expand in a reversible manner until the pressure drops
to 0.4 MPa. Determine (a) the final temperature in the cylinder and (b) the work done by the
refrigerant.

Here we assume that the process in our “well-insulated cylinder” is adiabatic. Since we are given
that the expansion is reversible, we have reversible adiabatic process. We know that such a
process is an isentropic (constant entropy) process, so that the final entropy equals the initial
entropy. We can use this fact to find the answers to both parts of this problem.
First we find the data for the initial state. Since this is a saturated vapor at 0.8 MPa, we find the
following saturated vapor properties from Table A-12 on page 930: v 1 = 0.025621 m3/kg, u1 =
246.79 kJ/kg, and s1 = 0.91835 kJ/kg∙K.
We can find the (constant) mass from the initial volume, V 1 = 0.05 m3 and the initial specific
volume.

V1 0.05 m 3
m   1.952 kg
v1 0.025621 m 3
kg
For this closed system, the first law is Q = U + W. Since Q = 0, our first law reduces to W = -U
= m(u1 – u2). We can find u2, because we know the pressure P2 = 0.4 MPa and the entropy s2 =
s1 = 0.91835 kJ/kg∙K at the final state. From the data on saturation properties at 0.4 MPa (400
kPa) in Table A-12 on page 930, we see that the value of s 2 lies between the values of sf =
0.24761 kJ/kg∙K and sg = 0.92691 kJ/kg∙K. Thus we know that we are in the mixed region. This
means that T2 = Tsat(P2 = 0.4 MPa) = 8.91oC .

We have to find the quality to determine the final internal energy.

s2  s f (0.4 MPa ) 0.91835 kJ  0.24761 kJ


kg  K kg  K
x2    0.9874
s fg (0.4 MPa ) 0.67929 kJ
kg  K
63.62 kJ 171.45 kJ 232.91 kJ
u 2  u f (0.4 MPa )  x 2 u fg (0.4 MPa )   (0.9874) 
kg kg kg
We now find the work from the first law.
 246.79 kJ 232.91 kJ 
W  m(u1  u2 )  (1.952 kg )  
 kg kg  = 27.08 kJ

Jacaranda (Engineering) 3519 Mail Code Phone: 818.677.6448


E-mail: [email protected] 8348 Fax: 818.677.7062
5 A piston-cylinder device contains 1.2 kg of saturated water vapor at 200oC. Heat is now transferred
to the steam and the steam expands reversibly and isothermally to a final pressure of 800 kPa.
Determine the heat transferred and the work done during this process.

Here, since the process is reversible we know that dS = dQ/T. Since it is isothermal we can
integrate this equation to obtain S = (dQ/T) = (1/T)dQ = Q/T. Thus, the heat transferred in the
process can be found from the equation Q = TS = Tm(s2 – s1). We can find the two entropy
values since we have enough data to specify the initial and final states. Once we know the heat
transfer, we can find the work from the first law, Q = U + W. Solving this equation for the work
gives W = Q – m(u2 – u1).
At the initial state of saturated vapor at 200oC, we find the following properties from Table A-4 on
page 916: s1 = sg(200oC) = 6.4302 kJ/kg∙K and u1 = ug(200oC) = 2594.2 kJ/kg. At the final state
where T2 = T1 = 200oC and P2 = 800 kPa (0.8 MPa), we find the properties from Table A-6 on
page 894: s2 = s(200oC,800 kPa) = 6.8177 kJ/kg∙K and u2 = u(200oC,800 kPa) = 2631.1 kJ/kg.
We use the entropy values to compute the heat transfer at the constant temperature of 200 oC =
473.15 K.)
 6.8177 kJ 6.4302 kJ 
Q  TS  Tm  s 2  s1   ( 473.15 K )1.2 kg    
 kg  K kg  K  = 220.0 kJ

We now use the first law to find the work.


 2631.1 kJ 2594.2kJ 
W  Q  m  u2  u1   220.0 kJ  1.2 kg    
 kg kg  = 175.7 kJ

6 A 50-kg copper block, initially at 80oC, is dropped into an insulated tank that contains 120 L of water
at 25oC. Determine the final equilibrium temperature and the total entropy change for this process.

Here we assume that the total system, consisting of the water and the copper block is isolated to
that there is no heat transfer or work between the tank (with the water and the block) and any
other system. In this case, the first law, Q = U + W becomes U = 0, or U = mCu(uCu,2 – uCu,1) +
mw(uw,2 + uw,1) = 0. We further assume that the change in internal energy can be modeled as the
product of a heat capacity and a temperature difference; i.e., du = cdT, where there is a negligible
difference between cp and cv for liquids and solids. From Table A-3 on page 915 we find the
following data on the heat capacity and density for copper and liquid water: at 25 oC, w = 997
kg/m3 and cw = 4.18 kJ/kg∙oC; at 27oC, cCu = 0.386 kJ/kg∙oC. (Note that we could also have the
following units for the heat capacities: kJ/kg∙K.) Assuming that the heat capacities are constant
we have the following equation for our first law:

mCu(uCu,2 – uCu,1) + mw(uw,2 + uw,1) = mCucCu(TCu,2 – TCu,1) + mwcw(Tw,2 + Tw,1) = 0

The final temperature of the copper and the water will be the same: T Cu,2 = Tw,2 = T2. Substituting
T2 for TCu,2 and Tw,2, and solving for T2 gives the following result for the final temperature.

m w cwT1,w  mCu cCu T1,Cu


T2 
m w c w  mCu cCu

We can find the mass of the water from the density and the volume.

Jacaranda (Engineering) 3519 Mail Code Phone: 818.677.6448


E-mail: [email protected] 8348 Fax: 818.677.7062
997 kg 120 L
mw   wVw   120 kg
m 3 1000 L
m3

We now have all the values required to compute T2.

4.18 kJ 0.386 kJ
(120 kg ) ( 25o C )  (50 kg ) (80o C )
m c T  mCu cCu T1,Cu kg o C kg o C
T2  w w 1,w  =
mw cw  mCu cCu 4.18 kJ 0.386 kJ
(120 kg )  (50 kg )
kg o C kg o C
27oC

We can now compute the entropy change. We assume that each substance undergoes an
internally reversible heat transfer such that dS = dQ/T = mcdT/T. The assumption that each
substance has a constant heat capacity allows us to integrate this equation giving S =
mcln(T2/T1). In this calculation the temperature must be in kelvins. We can apply this equation to
both substances, here using units of kelvins for the heat capacity.

 T  4.18 kJ  300.15  3.335 kJ


S w  mw cw ln 2   (120 kg )
 ln  
 T1,w  kg  K  298.15 K  kg  K

 T  0.386 kJ  300.15  3.140 kJ


S Cu  mCu cCu ln 2   (50 kg )
 ln   
 T1,Cu  kg  K  253.15 K  kg  K

The total entropy change is simply the sum of these two entropy changes.

3.335 kJ 3.140 kJ 0.215 kJ


S total  S w  S Cu   
kg  K kg  K kg  K

We see that the total entropy change for this isolated system is positive satisfying the second law
of thermodynamics that requires S  0 for an isolated system. However, the entropy change for
the copper, which is cooled in this process, is negative.

7 An insulated piston-cylinder device contains 0.05 m3 of saturated refrigerant 134a vapor at 0.8 MPa
pressure. Find the maximum work that can be done if the refrigerant expands to a pressure of 0.4
MPa in an adiabatic process.

The maximum work occurs in a reversible process. If we assume that the “insulated” device has
no heat transfer, we have an adiabatic process so the maximum work will be in a reversible
adiabatic process. In such a process, the entropy is constant. This constant entropy expansion
has already been solved in problem 4 where we found the work. We know that this must be the
maximum work, Wmax = 27.08 kJ

What lies beyond this message is totally useless so don’t bother

Why Is the Floodway Different than Other Floodplain Areas?

Jacaranda (Engineering) 3519 Mail Code Phone: 818.677.6448


E-mail: [email protected] 8348 Fax: 818.677.7062
A basic principle of floodplain management is that development must not increase the flood hazard on other properties. “Floodways” are areas where fill or other
development is likely to divert flow and contribute to increased water depths during a flood. Floodways may also be subject to high velocities, which can cause severe
damage to structures and high risks for occupants and emergency responders. Ideally, floodways should be undeveloped areas that can accommodate flood flows with
minimal risk. Any new development in the floodway generally requires an engineering analysis of the impact on flood hazards.

What Is Meant by Encroachment?

An “encroachment” is any floodplain development that could obstruct flood flows, such as fill, a bridge, or a building. A driveway, road, or parking lot at grade (without
any filling) would not cause an obstruction. Development of lakeshore floodplains, where there is no flow, is not considered an encroachment.

How Are Floodplain Encroachments Regulated?

The development standards for a floodplain encroachment depend on both the project location and the amount of information provided on flood hazard maps:

o Floodplain fringe: The modeling used to establish floodway boundaries indicated that any encroachment or obstruction in the fringe area (outside the
floodway) would not result in a “significant” increase in flood levels (i.e. no more than one foot), so no encroachment analysis is required.

o Floodway: No new development is permitted within the regulatory floodway unless a licensed professional engineer demonstrates that the proposed
encroachment shall not result in any rise in the 100-year flood elevation. This no-rise requirement is in addition to all other floodplain development standards applicable
to the proposed project.

o Riverine floodplain with base flood elevations, but no floodway: When the flood hazard map designates base flood elevations (100-year flood heights) but
no floodway is delineated, the applicant must demonstrate that the cumulative effect of the proposed development, when combined with all other existing and
anticipated floodplain development, would not increase the water surface elevation of the 100-year flood more than one foot at any location.

o Approximate A Zones: When floodplain boundaries were established using approximate techniques (which produce neither floodways nor base flood
elevations), the municipality may require an analysis to demonstrate that the project would not result in physical damage to any other property.

Are There Exceptions to the Encroachment Requirements?

Federal standards do not allow communities to issue variances for development within the floodway that would result in increased flood levels. However, there are
some situations (such as dams, bridges, or roads) in which a project in the floodway may be justifiable even though it would cause a rise in the flood elevation. This
necessitates that the flood hazard map be changed to reflect the new hazard. The applicant must apply to the Federal Emergency Management Agency (FEMA) for (1)
a conditional map revision before the development occurs and (2) a final letter of map revision after the development has been completed.

No-Rise Certification for Floodway Encroachments

Any proposed encroachment in the floodway requires a technical evaluation by a licensed professional engineer to demonstrate that the project will not affect flood
heights. The results of this analysis must be maintained in the municipality’s permit file. This can be in the form of a No-Rise Certification supported by technical data
and signed by a registered professional engineer. The supporting technical data should be based on the standard step-backwater computer model used to develop the
floodway shown on the flood hazard map. Hydraulic modeling of the pre-project and post-project conditions should demonstrate that the change in the 100-year flood
height is 0.00 feet.

Jacaranda (Engineering) 3519 Mail Code Phone: 818.677.6448


E-mail: [email protected] 8348 Fax: 818.677.7062
A detailed surface water profile analysis may not be necessary for a small project located completely within the “conveyance shadow” of an existing obstruction
(because flood water is already flowing around the larger obstruction). The limits of this conveyance shadow can be determined as illustrated

Jacaranda (Engineering) 3519 Mail Code Phone: 818.677.6448


E-mail: [email protected] 8348 Fax: 818.677.7062

You might also like