Scribd Logo
Upload

Welcome to Scribd!

  • 59 views

    Mini Wire Bender

    Uploaded by

    Masterbin2010
    The document provides instructions for using the #60346 Mini Wire Bender tool. It should be clamped securely in a bench-mounted vise with about 1/8" projecting above the vise jaws. The wire is inserted between the pivot pin and handle pin and rested against the screw pin, which is adjusted for the wire diameter. The handle is turned clockwise to bend the wire to the desired angle.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Mini Wire Bender

    Uploaded by

    Masterbin2010
    59 views1 page
    The document provides instructions for using the #60346 Mini Wire Bender tool. It should be clamped securely in a bench-mounted vise with about 1/8" projecting above the vise jaws. The wire is inserted between the pivot pin and handle pin and rested against the screw pin, which is adjusted for the wire diameter. The handle is turned clockwise to bend the wire to the desired angle.

    Original Description:

    DOBRADORA DE ARAME

    Original Title

    60346 MINI WIRE BENDER

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides instructions for using the #60346 Mini Wire Bender tool. It should be clamped securely in a bench-mounted vise with about 1/8" projecting above the vise jaws. The wire is inserted between the pivot pin and handle pin and rested against the screw pin, which is adjusted for the wire diameter. The handle is turned clockwise to bend the wire to the desired angle.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    59 views1 page

    Mini Wire Bender

    Uploaded by

    Masterbin2010
    The document provides instructions for using the #60346 Mini Wire Bender tool. It should be clamped securely in a bench-mounted vise with about 1/8" projecting above the vise jaws. The wire is inserted between the pivot pin and handle pin and rested against the screw pin, which is adjusted for the wire diameter. The handle is turned clockwise to bend the wire to the desired angle.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    INSTRUCTIONS FOR INSTRUCTIONS FOR

    #60346 MINI WIRE BENDER #60346 MINI WIRE BENDER


    For proper use, a sturdy bench-mounted vise is essential. The Mini For proper use, a sturdy bench-mounted vise is essential. The Mini
    Wire Bender will bend solid brass, steel, or steel music wire up to Wire Bender will bend solid brass, steel, or steel music wire up to
    1/8” diameter, plus square or rectangular metal shapes. 1/8” diameter, plus square or rectangular metal shapes.
    Step 1. Clamp the base securely in the vise, leaving about 1/8” Step 1. Clamp the base securely in the vise, leaving about 1/8”
    projecting above the vise jaws to to allow handle to swing freely. projecting above the vise jaws to to allow handle to swing freely.
    Step 2. With the pin on the handle pointing down, place handle Step 2. With the pin on the handle pointing down, place handle
    onto large pin on the base. Move the handle away fom you to onto large pin on the base. Move the handle away fom you to
    about 11 oʼclock position, and insert the wire between the pivot pin about 11 oʼclock position, and insert the wire between the pivot pin
    and the handle pin, resting against the right side of the screw pin. and the handle pin, resting against the right side of the screw pin.
    Use a 5/32” hex (Allen) wrench to adjust the height of the screw Use a 5/32” hex (Allen) wrench to adjust the height of the screw
    pin to accommodate the wire to be shaped. Tighten screw head pin to accommodate the wire to be shaped. Tighten screw head
    onto wire for more security. onto wire for more security.

    Step 3. Pull handle clockwise until desired angle is achieved. Step 3. Pull handle clockwise until desired angle is achieved.
    Step 4. A little experimenting and practice using coat hanger wire Step 4. A little experimenting and practice using coat hanger wire
    will save valuable material and improve results. Please be careful will save valuable material and improve results. Please be careful
    when bending music wire. Wear safety glasses when using this tool. when bending music wire. Wear safety glasses when using this tool.

    340 Snyder Avenue, Berkeley Heights, NJ 07922 340 Snyder Avenue, Berkeley Heights, NJ 07922
    Tech Support 908-464-1094 Tech Support 908-464-1094
    www.micromark.com [email protected] MM072610 www.micromark.com [email protected] MM072610

    INSTRUCTIONS FOR INSTRUCTIONS FOR


    #60346 MINI WIRE BENDER #60346 MINI WIRE BENDER
    For proper use, a sturdy bench-mounted vise is essential. The Mini For proper use, a sturdy bench-mounted vise is essential. The Mini
    Wire Bender will bend solid brass, steel, or steel music wire up to Wire Bender will bend solid brass, steel, or steel music wire up to
    1/8” diameter, plus square or rectangular metal shapes. 1/8” diameter, plus square or rectangular metal shapes.
    Step 1. Clamp the base securely in the vise, leaving about 1/8” Step 1. Clamp the base securely in the vise, leaving about 1/8”
    projecting above the vise jaws to to allow handle to swing freely. projecting above the vise jaws to to allow handle to swing freely.
    Step 2. With the pin on the handle pointing down, place handle Step 2. With the pin on the handle pointing down, place handle
    onto large pin on the base. Move the handle away fom you to onto large pin on the base. Move the handle away fom you to
    about 11 oʼclock position, and insert the wire between the pivot pin about 11 oʼclock position, and insert the wire between the pivot pin
    and the handle pin, resting against the right side of the screw pin. and the handle pin, resting against the right side of the screw pin.
    Use a 5/32” hex (Allen) wrench to adjust the height of the screw Use a 5/32” hex (Allen) wrench to adjust the height of the screw
    pin to accommodate the wire to be shaped. Tighten screw head pin to accommodate the wire to be shaped. Tighten screw head
    onto wire for more security. onto wire for more security.

    Step 3. Pull handle clockwise until desired angle is achieved. Step 3. Pull handle clockwise until desired angle is achieved.
    Step 4. A little experimenting and practice using coat hanger wire Step 4. A little experimenting and practice using coat hanger wire
    will save valuable material and improve results. Please be careful will save valuable material and improve results. Please be careful
    when bending music wire. Wear safety glasses when using this tool. when bending music wire. Wear safety glasses when using this tool.

    340 Snyder Avenue, Berkeley Heights, NJ 07922 340 Snyder Avenue, Berkeley Heights, NJ 07922
    Tech Support 908-464-1094 Tech Support 908-464-1094
    www.micromark.com [email protected] MM072610 www.micromark.com [email protected] MM072610

    You might also like