Troubleshooting HVACR Systems Using

Superheat and Subcooling

August 7, 2006
One Comment
Email / Print / Reprints / Share on facebook Share on twitter Share on linkedin | More / Text
Size+
Object 1

Object 2

Object 3
Related Articles

AEC Store Offers HVACR DVDs

Work Seekers: 05/26/2003

More On The Basic Refrigeration System

Troubleshooting A Refrigerant Undercharge

Troubleshooting With Superheat, Subcooling

Fieldpiece Instruments: Superheat and Subcooling Meter

Related Products

HVACR Technician Training DVD/Video Library Bundle

Understanding TXV Refrigeration Systems: Superheat and

Subcooling DVD
Related Events

Compressor Operation and Service Seminar (COSS) (July 10,

2012 - July 12, 2012)

AHR Expo-Mexico (September 25, 2012 - September 27, 2012)

Testing rooftop refrigeration system with a Fluke 561 Infrared Thermometer.

Troubleshooting and servicing refrigeration and air conditioning systems can be a challenging
process for both the entry level and experienced HVACR technician. Regardless of your experience,
size of the equipment, or location, to troubleshoot the system it is essential that you have a solid
understanding of the fundamentals of refrigeration - including the principles of superheat and
subcooling. You also need to have the right tools and know-how to apply these principles to use the
tool quickly and efficiently.
Troubleshooting techniques often require simultaneous knowledge of temperature, pressure,
voltage, and current values in a system, which means that a single-function meter won't permit a
complete analysis of the system. Frequently, multiple tools are required.
This article provides information on troubleshooting the refrigeration system while applying the
principles of superheat and subcooling to HVACR equipment. It will also teach you the proper
methods to tackle some typical troubleshooting tasks using thermometers, digital multimeters,
pressure/vacuum modules, and HVACR accessories. Basic refrigeration principles are provided
solely to illustrate how digital thermometers, multimeters, and accessories can make servicing and
maintaining HVACR systems straightforward, fast, and accurate.

Figure 1. The refrigeration system. In a typical refrigeration system, the compressor sends hot gas
to the condenser. Then the condensed liquid passes through an expansion valve into the evaporator
where it evaporates and collects heat from the area to be cooled. The gaseous refrigerant then enters
the compressor where the compression process raises the pressure and temperature. From the
compressor, the refrigerant is routed back to the condenser and the cycle repeats.

THE REFRIGERATION CYCLE

Based on the principle that heat flows naturally from warmer areas to cooler areas, the refrigeration
cycle consists of seven stages:
1. Compression of hot gas
2. Cooling
3. Condensing
4. Subcooling
5. Expansion
6. Evaporation
7. Super heating
A basic vapor compression refrigeration system consists of four primary components: a metering
device (e.g., a capillary tube, fixed orifice/piston, or a thermostatic expansion valve), evaporator,
compressor, and condenser. (See Figure 1.)
Compression energy elevates the vapor pressure to a boiling point that is below the condensing
mediums' temperature. In other words, the compressor elevates the boiling point of the refrigerant
to a point at which the air (or water) moving across the condenser is low enough to condense the
refrigerant to a liquid. Additional passes in the condenser coil cool the liquid refrigerant below its
boiling point to ensure it remains a liquid as it experiences pressure drop in its journey to the
evaporator. This cooling below the boiling point is called subcooling.
A metering device at the evaporator inlet acts as a "dam" to restrict flow and drop the refrigerant
pressure to a new lower boiling point. This new boiling point is below the evaporator medium (air
or water) temperature so that the air or water across the evaporator will cause the refrigerant to boil.
After all of the refrigerant in the evaporator has boiled to a vapor, the vapor will pick up additional
heat through extra passes in the evaporator. The amount of vapor temperature increase above the
boiling temperature is called superheat.
The compressor reduces the gas to a high pressure while simultaneously raising the temperature of
the gas. The hot gas is then delivered to the condenser where it is cooled, dissipating the heat and
steadily converting the gas back to a liquid state.
Note: Liquid receivers are not typically used on refrigeration systems, which commonly rely on
capillary tubes or fixed metering devices.
When the liquid under high pressure reaches the metering device, the cycle starts over.
While servicing most refrigeration systems, the technician will measure the temperature and
pressure to determine system performance. Close monitoring of temperature and pressure to verify
proper control and operation can ensure longer system life and reduce energy consumption.
Often, measuring temperatures or pressures at key points in a system can pinpoint trouble spots.
Examples of such measurements follow.

Figure 2. Superheat temperature measurement points. (Click on the illustration to view a larger
image.)

SUPERHEAT AND ITS MEASUREMENT

In the system's evaporator, conversion of liquid to vapor involves adding heat to the liquid at its
boiling temperature, commonly referred to as the saturation temperature. After all of the refrigerant
has boiled to a vapor, any additional temperature increase above the boiling point is called
superheat.
Finding suction line superheat requires finding the suction pressure and two temperatures - the
evaporator boiling temperature at a given pressure and the temperature of the refrigerant at the
outlet of the evaporator on the suction line, commonly referred to as the superheat
temperature/pressure method.
Finding the boiling temperature is determined by using a pressure-temperature (PT) chart. On older
CFC and HCFC refrigerants, and some newer ozone-friendly refrigerants such as R-134a, boiling
temperature remains constant during the saturation or boiling phase provided that the pressure
remains the same within the evaporator.
On newer refrigerant blends, the temperature changes during the boiling or saturation phase. This is
referred to as glide. Modern refrigerants with a temperature glide of 10°F (5°C) or higher use
dew point (DP) temperature. This is the temperature of the refrigerant when the last of the liquid has
boiled into a vapor. Any vapor temperature increase above the dew point temperature is called
superheat. (See Figure 2.)

Figure 3. Suction line superheat using the temperature-pressure method. Measure the pressure at
the suction line service valve. Find the evaporator boiling temperature from a temperature-pressure
chart using suction line pressure. Subtract this temperature from the suction line temperature
measured by a digital thermometer. The difference is superheat.
One of the best methods to determine superheat is to use a pipe clamp temperature probe and a
pressure/vacuum module in conjunction with a suitable digital multimeter with type K
thermocouple measurement and a mV input. The pipe clamp temperature probe allows pipe
temperature measurements to be made more quickly and accurately because it clamps directly to the
pipe without the need to add insulation or tape, as in the case of a bead thermocouple. The
pressure/vacuum module allows accurate and quick pressure measurements.
When measuring for superheat, remember to allow the system to run long enough for temperatures
and pressures to stabilize while verifying normal airflow cross the evaporator. Using the pipe clamp
or a Velcro pipe probe, find the suction line temperature by attaching the probe around a bare
section of the pipe, at the outlet of the evaporator. Pipe temperature can be read at the inlet of the
compressor on the suction line if the pipe is less than 15 feet from the evaporator and there is a
minimum pressure drop between the two points. (See Figure 3.) Best results are obtained when the
pipe is free of oxides or other foreign material.
Next, attach the pressure/vacuum module to the suction line service valve (or refrigerant service
port on your manifold gauge set). Make a note of the pipe temperature and pressure. This pressure
reading will be that of the boiling refrigerant inside the evaporator, assuming no abnormal
restrictions exist within the suction line. Using this pressure value, find the evaporator (or dew
point) boiling temperature from a PT chart for the refrigerant type being used. Subtract the
boiling/dew point temperature from the suction line temperature to find the superheat.
The suction line temperature may also be taken by attaching a bead thermocouple to the suction
line. Be careful to insulate the thermocouple and use heat-conducting compound to minimize errors
due to heat loss to ambient air.

Figure 4. Subcooling. After verifying normal airflow, place the pipe clamp or Velcro probe on the
liquid line. Note the temperature. Then attach the pressure/vacuum module to a port on the liquid
line and measure the liquid line pressure. Determine the condensing temperature by using the
temperature-pressure chart for the refrigerant type used. The difference in temperature is the
subcooling value.

SUBCOOLING AND ITS MEASUREMENT

In the system's condenser, conversion of vapor to liquid involves removing heat from the refrigerant
at its saturation condensing temperature. Any additional temperature decrease is called subcooling.
Finding liquid line subcooling requires determining the condensing pressure and two temperatures -
the condensing temperature at the measured condensing pressure and the temperature of the
refrigerant at the outlet of the condenser on the liquid line. The liquid line temperature involves
measuring the surface temperature of the pipe at the outlet of the condenser. (See Figure 4.)
Note: Condensing temperature is derived from using the PT chart. On new refrigerant blends with
high temperature glide, this is called the bubble point (BP) temperature. See Figure 2.

To measure subcooling with a pipe clamp temperature probe, or a Velcro pipe probe, allow the
system to run long enough for temperatures and pressures to stabilize. Verify normal airflow and
then find the liquid line temperature by clamping the pipe clamp around the liquid line. Attach the
pressure/vacuum module to a service port on the liquid line (or discharge line at the compressor if a
liquid line service valve port is not available). Make a note of the liquid line temperature and
pressure. Convert the liquid line pressure to temperature using a PT chart for the refrigerant type
being used. The difference of the two temperatures is the subcooling value.

TROUBLE DIAGNOSIS
Data from superheat and subcooling measurements can be useful for determining various conditions
within the HVACR system, including the amount of refrigerant charge and verifying the operating
condition of the metering device. These measurements can also be used to determine the efficiency
of the condenser, evaporator, and compressor.
Before making conclusions from the measured data, it is important to check external conditions that
influence system performance. In particular, you should inspect and verify the proper airflow in
cubic feet per minute (cfm) across coil surfaces and line voltage to the compressor motor and
associated electrical loads. Remember to look for obvious problems at the coil surfaces such as dirty
air filters upstream of the evaporator, or leaves and outside debris restricting airflow on the
condenser.
Measuring liquid line temperature with a DMM and a pipe clamp.

USING SUPERHEAT TO TROUBLESHOOT

The superheat value can indicate various system problems including a clogged filter drier,
undercharge, overcharge, faulty metering device, restricted airflow, or improper fan motor or
blower direction. Suction line superheat is a good place to start diagnosis because a low reading
suggests that liquid refrigerant may be reaching the compressor. In normal operation, the refrigerant
entering the compressor is sufficiently superheated above the evaporator boiling temperature to
ensure the compressor draws only vapor and no liquid refrigerant. On traditional HVACR systems,
which utilize mechanical metering devices such as a TXV or cap tube, the superheat heating will
vary between 8°F to 20°F. On newer systems, which use electronic expansion valves and solid
state controllers, it is possible to see the superheat setting as low as 5°F to 10°F.
A low or zero superheat reading indicates that the refrigerant did not pick up enough heat in the
evaporator to completely boil into a vapor. Liquid refrigerant drawn into the compressor typically
causes slugging, which can damage the compressor valves and/or internal mechanical components.
Additionally, liquid refrigerant in the compressor, when mixed with oil, reduces lubrication and
increases wear, causing premature failure.
On the other hand, if the superheat reading is excessive - above 20°F to 30°F - it indicates that
the refrigerant has picked up more heat than normal, or that the evaporator is being starved of
refrigerant. Possible causes of this condition include a metering device that is underfeeding,
improperly adjusted, or simply broken. Additional problems with high superheat could indicate a
system undercharge, a refrigerant restriction, moisture in the system, a blocked filter drier, or
excessive evaporator heat loads.

Measuring temperature and suction pressure to determine superheat.

USING SUBCOOLING TO TROUBLESHOOT

An improper subcooling value can indicate various system problems including overcharge,
undercharge, liquid line restriction, or insufficient condenser airflow (or water flow when using
water-cooled condensers). The refrigerant is typically subcooled between 10°F to 20°F at the
outlet of the condenser, however, some modern equipment may have subcooling values as low as 4
degrees in order to meet minimum efficiency standards.
For example, a very low reading between zero to 10°F subcooling indicates that the refrigerant
did not lose the normal amount of heat in its travel through the condenser. Possible causes for this
condition include insufficient airflow over the condenser, metering device problems such as
overfeeding, misadjustment, or being stuck too far open, or the system may be undercharged.
Oftentimes, the problem is simply that the condenser coil surface needs to be cleaned thoroughly to
eliminate airflow restriction.
Excessive subcooling means the refrigerant was cooled more than normal. Possible explanations
include an overcharged system, a restriction in the metering device, misadjusted (underfeeding), or
faulty head pressure control during low ambient conditions.

PRINCIPLES OF THE REFRIGERATION CYCLE

AND TROUBLESHOOTING SUMMARY
The next time you are called upon to service or maintain any HVACR equipment, remember to be
patient and apply the principles you have learned in this article. Check the superheat and subcooling
at the unit. Be sure to do a visual inspection of the equipment to verify that all coil surfaces are
clean and that fans are running in the right direction. You need to have the right tools and know-how
to apply these principles to use the tool as it was designed. Digital thermometers, multimeters,
pressure/vacuum modules, and accessories will help you solve the problem and repair the
equipment correctly the first time.
Reprinted with permission from the Fluke Corp. Application Note "Troubleshooting HVAC/R
systems using refrigerant superheat and subcooling." For more information, visit www.fluke.com