Scribd
Upload
9 views

1.5 Energy Relationships and The Bemoulll Equation: Fluids in Motion 9

This document discusses the different forms of energy in fluids in motion, including internal, potential, pressure, and kinetic energy. It presents an equation (1.8) that sums these components to calculate the total energy per unit mass of a fluid. The document also introduces the Bernoulli equation (1.10), which relates the total energy at one point in a fluid flow to another by accounting for changes in elevation, pressure, velocity, as well as any work or heat transfer between the points.

Uploaded by

Mrinal Kanti Bhaduri
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
9 views

1.5 Energy Relationships and The Bemoulll Equation: Fluids in Motion 9

This document discusses the different forms of energy in fluids in motion, including internal, potential, pressure, and kinetic energy. It presents an equation (1.8) that sums these components to calculate the total energy per unit mass of a fluid. The document also introduces the Bernoulli equation (1.10), which relates the total energy at one point in a fluid flow to another by accounting for changes in elevation, pressure, velocity, as well as any work or heat transfer between the points.

Uploaded by

Mrinal Kanti Bhaduri
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

FLUIDS IN MOTION 9

This is the form of the Continuity Equation that will be used most
frequently but it is valid only when there is no accumulation. Although
Figure 1.3 shows a pipe of circular cross section, equations 1.4 to 1.7 are
valid for a cross section of any shape.

1.5 Energyrelationshipsand the Bemoulll equation

The total energy of a fluid in motion consists of the following components:


internal, potential, pressure and kinetic energies. Each of these energies
may be considered with reference to an arbitrary base level. It is also
convenient to make calculations on unit mass of fluid.

Internal energy This is the energy associated with the physical state of
the fluid, ie, the energy of the atoms and molecules resulting from their
motion and configuration [Smith and Van Ness (1987)]. Internal energy is
a function of temperature. The internal energy per unit mass of fluid is
denoted by U.

Potential energy This is the energy that a fluid has by virtue of its
position in the Earth's field of gravity. The work required to raise a unit
mass of fluid to a height z above an arbitrarily chosen datum is ~g, where g
is the acceleration due to gravity. This work is equal to the potential
energy of unit mass of fluid above the datum.

Pressure energy This is the energy or work required to introduce the


fluid into the system without a change of volume. If P is the pressure and
V is the volume of mass m of fluid, then P V/m is the pressure energy per
unit mass of fluid. The ratio ndV is the fluid density p. Thus the pressure
energy per unit mass of fluid is equal to P/p.

Kinetic energy This is the energy of fluid motion. The kinetic energy of
unit mass of the fluid is t~2/2, where ~ is the velocity of the fluid relative to
some fixed body.

Total energy Summing these components, the total energy E per unit
mass of fluid is given by the equation
p ~2
E = U+zg+- +-- (1.8)
p 2
10 FLUID FLOW FOR CHEMICAL ENGINEERS

where each term has the dimensions of force times distance per unit mass,
ie (ML/T2)L/M or L2/T 2.

Consider fluid flowing from point 1 to point 2 as shown in Figure 1.4.


Between these two points, let the following amounts of heat transfer and
work be done per unit mass of fluid: heat transfer q to the fluid, work Wi
done on the fluid and work Wo done by the fluid on its surroundings. Wi
and Wo may be thought of as work input and output. Assuming the
conditions to be steady, so that there is no accumulation of energy within
the fluid between points I and 2, an energy balance can be written per unit
mass of fluid as
E1 + Wi+ q - E2+ Wo
or, after rearranging
E2 = El +q+ W i - Wo (1.9)

A flowing fluid is required to do work to overcome viscous frictional


forces so that in practice the quantity Wo is always positive. It is zero only
for the theoretical case of an inviscid fluid or ideal fluid having zero
viscosity. The work Wi may be done on the fluid by a pump situated
between points 1 and 2.
If the fluid has a constant density or behaves as an ideal gas, then the
internal energy remains constant if the temperature is constant. If no heat
transfer to the fluid takes place, q=O. For these conditions, equations 1.8
and 1.9 may be combined and written as

--+ = aft+---+ + Wi- Wo (1 10)


u p, 7 "

Q, "t _it wo

!| E,= .._

Figure 1.4
Energy balance for fluid flowing from location I to location 2

You might also like