Tests - Concrete - Apr 1, 2020

Hilti PROFIS Engineering 3.0.
58
www.hilti.ca
Company: Page: 1
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Apr 1, 2020 Date: 2020-04-01
Fastening point:
Specifier's comments:
1 Input data
Anchor type and diameter: HIT-HY 200 + HIT-Z 1/2
Item number: 2018443 HIT-Z 1/2" x 4 1/2" (element) / 2022793
HIT-HY 200-R (adhesive)
Effective embedment depth: hef,opti = 69.9 mm (hef,limit = 152.4 mm)
Material: DIN EN ISO 4042
Evaluation Service Report: ESR-3187
Issued I Valid: -|-
Proof: Design Method CSA A23.3-14 / Chem
Stand-off installation: eb = 0.0 mm (no stand-off); t = 12.7 mm
Anchor plate :
R lx x ly x t = 508.0 mm x 508.0 mm x 12.7 mm; (Recommended plate thickness: not calculated)
Profile: W shape (AISC), W4X13; (L x W x T x FT) = 105.7 mm x 103.1 mm x 7.1 mm x 8.8 mm

Base material: 2
cracked concrete, fc' = 17.24 N/mm ; h = 10,668.0 mm, Temp. short/long: 20/20 °C
Installation: hammer drilled hole, Installation condition: Dry
Reinforcement: tension: condition B, shear: condition B; no supplemental splitting reinforcement present
edge reinforcement: none or < 15M bar
R
- The anchor calculation is based on a rigid anchor plate assumption.
Geometry [mm] & Loading [kN, kNm]
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2019 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
1
Hilti PROFIS Engineering 3.0.58
www.hilti.ca
Company: Page: 2
Address: Specifier:
Fastening point:
1.1 Design results

Case Description Forces [kN] / Moments [kNm] Seismic Max. Util. Anchor [%]
1 Combination 1 N = 2.000; Vx = 0.000; Vy = 0.000; no 10
Mx = 0.000; My = 0.000; Mz = 0.000;
Nsus = 0.000; Mx,sus = 0.000; My,sus = 0.000;
2
www.hilti.ca
Company: Page: 3
Address: Specifier:
Fastening point:
2 Proof I Utilization (Governing Cases)

Design values [kN] Utilization
Loading Proof Load Capacity bN / b V [%] Status

Tension Concrete Breakout Failure 2.535 26.530 10 / - OK
Shear - - - -/- N/A
Loading bN bV z Utilization b N,V [%] Status

Combined tension and shear loads - - - - N/A
3 Warnings
• Please consider all details and hints/warnings given in the detailed report!
Fastening meets the design criteria!
3
www.hilti.ca
Company: Page: 4
Address: Specifier:
Fastening point:
4 Remarks; Your Cooperation Duties

• Any and all information and data contained in the Software concern solely the use of Hilti products and are based on the principles, formulas
and security regulations in accordance with Hilti's technical directions and operating, mounting and assembly instructions, etc., that must be
strictly complied with by the user. All figures contained therein are average figures, and therefore use-specific tests are to be conducted
prior to using the relevant Hilti product. The results of the calculations carried out by means of the Software are based essentially on the
data you put in. Therefore, you bear the sole responsibility for the absence of errors, the completeness and the relevance of the data to be
put in by you. Moreover, you bear sole responsibility for having the results of the calculation checked and cleared by an expert, particularly
with regard to compliance with applicable norms and permits, prior to using them for your specific facility. The Software serves only as an
aid to interpret norms and permits without any guarantee as to the absence of errors, the correctness and the relevance of the results or
suitability for a specific application.
• You must take all necessary and reasonable steps to prevent or limit damage caused by the Software. In particular, you must arrange for
the regular backup of programs and data and, if applicable, carry out the updates of the Software offered by Hilti on a regular basis. If you do
not use the AutoUpdate function of the Software, you must ensure that you are using the current and thus up-to-date version of the Software
in each case by carrying out manual updates via the Hilti Website. Hilti will not be liable for consequences, such as the recovery of lost or
damaged data or programs, arising from a culpable breach of duty by you.

Tests - Concrete - Apr 1, 2020

Uploaded by

Copyright:

Available Formats

Tests - Concrete - Apr 1, 2020

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Tests - Concrete - Apr 1, 2020

Uploaded by

Copyright:

Available Formats

Hilti PROFIS Engineering 3.0.

Profile: W shape (AISC), W4X13; (L x W x T x FT) = 105.7 mm x 103.1 mm x 7.1 mm x 8.8 mm

Geometry [mm] & Loading [kN, kNm]

1.1 Design results

2 Proof I Utilization (Governing Cases)

Loading Proof Load Capacity bN / b V [%] Status

Loading bN bV z Utilization b N,V [%] Status

Fastening meets the design criteria!

4 Remarks; Your Cooperation Duties

You might also like