Quick Reference Manual

Getting started
Logger Pro Requirements
To use Logger Pro, you must have the following equipment:
Ñ Windows® 2000, XP, or Vista with Pentium® processor, 500 MHz
or better, 256 MB available RAM, 100 MB of hard disk space for a
minimum installation. Available USB or serial port.
Ñ Macintosh OS® (PPC or Intel) OS X 10.3 or 10.4 built-in USB port.
(English language version only.)
Using the movie feature of Logger Pro will require a faster processor
and more memory, such as a 2 GHz processor with 1 GB RAM. Movies
are supported by QuickTime®, which you can add during Logger Pro
installation.
Note: Logger Pro cannot be used with the ULI or Serial Box interface.
Contact us for the availability of earlier versions of Logger Pro for
older operating systems or interfaces.

Load Logger Pro

Windows
Ñ Place the Logger Pro CD in the CD-ROM drive of your computer.
Ñ If you have Autorun enabled, the installation will launch
automatically; otherwise launch Setup.exe from the CD.
Ñ The Logger Pro installer will start, and a series of dialog boxes
will step you through the installation of the Logger Pro software.
We recommend that you accept the default directory.

Macintosh
Ñ Place the Logger Pro CD in the CD-ROM drive of your computer
and double-click on the CD icon.
Ñ Double-click the “Install Logger Pro” icon and follow
the instructions.

2
Get Everything Ready
To collect data with Logger Pro you will need either a LabPro® or a Go!®Link,
with at least one sensor, or one of several dedicated sensors listed below.

A Vernier LabPro interface: A Go! Link interface:

The Vernier LabPro is a Go! Link is a single-channel
multi-channel interface interface that connects
with its power supply and directly to a computer’s
USB or serial cable USB port.
And, at least one sensor:
Sensors are connected to the LabPro or Go! Link. A Stainless Steel
Temperature Probe is a good choice for initial testing of Logger Pro.
The Voltage Probe included with the LabPro interface can also be used.
Ñ Or, Go! Temp
The Vernier Go!Temp is a temperature probe that connects directly
to the USB port of your computer. No interface is needed. This
sensor comes with the Logger Lite software.

Ñ Or, Go! Motion

The Go! Motion is a motion detector that connects
directly to a computer’s USB port.

Ñ Or, WDSS
The Wireless Dynamics Sensor System collects
acceleration, force, and altitude data. It requires a
Bluetooth-equipped computer

Ñ Or, Spectrometer
The Vernier Spectrometer measures intensity and
absorbance over many wavelengths simultaneously.

Ñ Or, Garmin GPS

(Windows only) Select Garmin GPS units can connect
to Logger Pro for live data collection, or the retrieval
of stored tracks or waypoints.
Ñ Or, Ohaus Balances
Logger Pro allows you to collect mass data from select models of
Ohaus balances.

3
Initial Setup
Note: The following setup instructions are for the LabPro interface. They are
similar to the Go! Link interface instructions. Choose Logger Pro 3 Help from
the Help menu (Windows) or Apple menu (Mac) for further details.

Before launching Logger Pro, you should:

Ñ Power the LabPro using the AC power supply
or AA batteries.
Ñ Connect a sensor to LabPro.
Ñ Connect the USB or serial cable to LabPro.
Ñ Attach the other end of the interface cable
to any unused serial port or USB port on
your computer.

Start Logger Pro

Locate the Logger Pro icon and double-click on it.
Mac OS X users can find the icon in the Logger Pro folder created in
Applications during installation.

Note: The first time that you run Logger Pro with your LabPro interface, a
message may appear notifying you of an update to the LabPro operating
system. Do not interrupt this update.

Logger Pro can collect data from multiple interfaces and devices. If
Logger Pro has successfully detected these devices, you will see the
device icon (see figure below). Also, if an auto-ID sensor is attached,
the current sensor reading will appear below the toolbar (as shown in
the figure). Some devices, such as WDSS, GPS or Ohaus balances, require
manual connection in Logger Pro. Choose Connect Interface‡(device name)
from the Experiment menu to connect.

In the figure above, a Go!Link, Go!Temp, LabPro and Ohaus balance

are connected to the computer.

You have now successfully set up your equipment and installed Logger Pro.
Keep reading for instructions on the various ways to collect and obtain data.
You will also learn how to use Logger Pro’s powerful features, such as data
analysis, movies, and customizing your experiments.

4
 TABLE OF CONTENTS
This guide first leads you through the basics of Logger Pro,
including software installation procedures. You will learn how
to collect data, manually enter data, and import data from
Texas Instruments and Palm handhelds. From there, you will
learn about the more advanced features of Logger Pro.

Introduction.......................................................... 6
Tutorials................................................................... 7
Acquiring Data
Collect Data............................................................... 7-8

Manually Enter Data.................................................... 9

Import Data.................................................................. 9

Remote Data................................................................. 9

Finding Your Way around Logger Pro

Logger Pro Toolbar and Pages................................... 10

The Sensors Dialog..................................................... 12

Managing Your Page and Data................................... 12

Analyze Data............................................................... 14

Printing........................................................................ 15

Where to Next?........................................................... 15

5
Introduction
Logger Pro is a program that allows you to collect and analyze data from
Vernier LabPro, Go! Link, Go!Temp, Go! Motion, Vernier/Ocean Optics
Spectrometers, the Vernier WDSS, and Ohaus balances. Among its many
features, data may be manually entered from the keyboard, pasted from
the clipboard, or retrieved from a file saved on disk. Logger Pro is also a
document creator, with the ability to include several pages in one document.
With Logger Pro you can also:
Ñ Perform data analysis, such as statistical analysis, curve fitting,
and calculated columns.
Ñ Add pictures to lab reports.
Ñ Add movies and synchronize movies with data collection.
Ñ Import data collected with TI handhelds.
Ñ Import data collected with Palm OS® handhelds.
Ñ Manually enter data.
Ñ Export data to Excel® or other spreadsheets.
Ñ Have students draw a prediction on a graph and see how well the
experimental data matches it.
Ñ Use video analysis to create a graphical representation of the motion
you see in a movie.
Ñ Use video capture to record video streaming from digital camera
or webcam.
The Help guide in the program provides complete details about Logger Pro.
Tutorials are also included. Select Open from the File menu to access them.

6
Tutorials
There are tutorials that cover many Logger Pro features and menus. Simply
choose Open from the File menu, then open the Tutorials folder:
Ñ Getting Started Ñ Motion Measurement
Ñ Stats, Tangents, Integrals Ñ Linearization (Parts 1 and 2)
Ñ Events with Entry Ñ Manual Data Entry
Ñ Curve Fitting Ñ Video Analysis
All you need to do is open the tutorial file you want to try out, and then
follow the on-screen instructions in that file.

The extensive Help in Logger Pro provides detailed instructions

for use of the program. The answer you are looking for may be
just a mouse click or two away!

Acquiring Data
Use any of the following methods to acquire Logger Pro data.

Collect Sensor Data

Before you can collect data, you should have already performed the following
steps, as outlined in the Getting Started section earlier in this booklet.
Note: The following setup instructions are for the LabPro interface. They are
similar to the Go! Link interface instructions. Choose Logger Pro 3 Help from the
Help menu for further details.
Ñ Power the LabPro using the AC power supply or AA batteries.
Ñ Install Logger Pro
Ñ Connect a sensor to LabPro
Ñ Connect LabPro to an available serial or USB port
Ñ Start Logger Pro

Configure Logger Pro for Your Experiment

There are several ways to set up Logger Pro for an experiment. Most
often you will just start Logger Pro with auto-ID Sensors connected.
Ñ Auto-ID Sensors With auto-ID sensors, all you need to do is connect
the sensor to one of the LabPro channels and start Logger Pro software.
The sensor will be identified, and default data-collection parameters
loaded for that sensor. You are ready to click the button and
begin data collection!

7
 Ñ Probes & sensors experiment files If you are using an older
Vernier sensor that is not auto-ID, or if you want to use some other
specially configured file, you will need the Probes & Sensors folder.
Choose Open from the File menu, and open the Probes & Sensor folder.
There you will find a folder for each of the Vernier sensors. Open up a
file with a name that best fits the data collection you want to perform.
Ñ Vernier lab book experiment files When you choose Open from
the File menu, you will see a series of folders with Vernier lab book
experiment files, such as Biology with Computers, etc. Each of these
folders contains 30-40 experiment files, each corresponding to an
experiment in each of our lab books.
Ñ Sensor dialog This
dialog, called by clicking
the respective button
in the toolbar ( , for
example) shows your
sensor information, the
units and current readings.
If an auto-ID sensor is
connected, Logger Pro
will identify the sensors
connected. Or, if your sensor is not auto-ID, you can simply drag the sensor
to the appropriate channel.

Collect Data
Click . Logger Pro will begin plotting data in the graph window.
Tip: Normally, the data collection stops at the time indicated on the time
axis. You can stop the data collection early by clicking . If you discover you
want the data collection to go even longer, you can add additional time by
choosing Extend Collection from the Experiment menu.
Now that you have collected data, there are many things you can do with it. Keep
reading for descriptions of some of the most commonly-used Logger Pro features.

Store Data
The Store Latest Run option in the Experiment menu saves the most recently
collected data in memory, allowing you to do another collection while
keeping the first one.
The run labeled “Latest” always contains the most recently collected data,
and is overwritten when you collect more data. When you store the latest
run, a new data set named Run 1, Run 2, etc, is created and the values of the
latest data set are copied to it. Columns in the latest data set are drawn with
thick lines on the graph, while other columns are drawn with thin lines.
Note: Using Store Latest Run does not save data on disk, nor will it preserve your
data between sessions or when you turn off your computer. You must select Save
As from the File menu to save your session (data and analysis) to disk.

8
Data Collection and Modes
You are not limited to time-based data collection.
Choose Data Collection from the Experiment menu
to modify data collection parameters for your
experiment. See Logger Pro’s Help for information
about your choices.
Time Based Set the data collection rate as a
function of time.
Events With Entry A data point is recorded whenever the Keep button is
clicked. You are then prompted to enter values for a new data column.
Selected Events A data point is recorded whenever the Keep button is clicked.
Digital Events You can set data collection to run continuously (until the Stop
button is clicked) or at a certain number of events.

Manually Enter Data

You can type data directly into the data table from the
keyboard. To manually enter data, disconnect all interfaces,
and start Logger Pro. Click on a cell and type in a number.
You can use the mouse or the Enter/Return key to move
and edit within the table. Your values will also be plotted
on the graph.

Import Data
Ñ You can import data from Texas Instruments
graphing calculators, LabPro, or CBL 2 devices using
the TI Connectivity Cable. Do so by choosing Import
From‡TI Device from the File menu or clicking the button.
The dialog box to the right will appear with the available
data lists for importing.
Ñ Data collected and stored in the LabPro interface using its Quick Setup
feature can be imported via the serial or USB cable. Do so by choosing
Import From‡LabPro from the File menu.
Ñ Data collected with a Palm OS handheld running the
Vernier Data Pro program can be imported by first
starting up Logger Pro, placing the Palm OS handheld
into its HotSync® cradle, and pressing the HotSync
button. Data are then displayed in the table and graph
of Logger Pro, where you can print or do further analysis.

Remote Data
LabPro, Go! Motion and WDSS can collect data without a computer attached.
You can use Logger Pro to set up the experiment, detach the device, collect
data remotely, then reattach the device to the computer to retrieve the data.
Select Remote‡Setup from the Experiment menu to set up LabPro, Go! Motion
or WDSS for remote data collection.
9
Finding Your Way
around Logger Pro
Take a few moments to get familiar with Logger Pro’s layout.

Logger Pro Screen and Toolbar

Toolbar The toolbar contains buttons for the most commonly used features of
Logger Pro. All of the features in the toolbar are also available in the menus. As you
move the pointer across a button, you are given a short description of each feature.

Click To
Create a new document.
Open an existing document.
Save the active document or template with its current name.
Print the screen as displayed on your monitor.
Scroll between pages.

Bring up the previous page of the current document.

Bring up the next page of the current document.
Bring up the Data Browser Window.
Import data from the Texas Instruments calculator.
Automatically scale the graph to include all data points.
Zoom in to the selected region of the graph.
Zoom out by a factor of two in both x- and y-directions.
Enter Examine mode.
Enter Tangent Line mode.
Integrate selected data range.
Calculate statistics on selected data.
Make a linear fit to the selected range.
Perform general curve fits.
Set data-collection parameters.
Begin collecting data.
(The following icons only appear when collecting data or if is relevant.)
Stops collecting data or stops a replay.
Tells the heat pulser to generate a pulse.
Click this button to keep a data point.
Click the Zero button to set the current value of a sensor to zero.
Create a new Graph Match.

10
Menu bar Logger Pro has a menu bar across the top of the main
window. Use the menu bar to access all of the software’s features.

Objects You can add new objects using the items in the Insert menu
and modify them using the Options menu or by double-clicking on the
objects. Some objects are listed here:
Graph Available graphs include Cartesian (2-D), Histogram, FFT Graph.
Table Displays data in data sets.
Text A small text editor. Use it to record notes for your file.
Text Annotation Allows you to enter and edit notes about the data.
Meter Displays the values of data columns in large digits, as a
thermometer, gauge, or animated display.
Movie You can add a movie of an experiment to your page, then
synchronize data collection to the movie.
Picture You can add a digital picture object to your page.

Navigate Between Pages

Logger Pro 3 has “pages.” These pages allow you to have space for
many layouts of graphs, data tables and other screen objects in a single
file. One page might contain a graph and table with five different data
collections. On different pages you might perform comparisons between
different collections or just go into each collection in more detail.
Click on the Toolbar to jump to the next page.
Click on the Toolbar to jump to the previous page.
You can also use the drop-down menu from the
Toolbar to choose a page directly.

11
The Sensors Dialog
This dialog, called up by clicking
the respective button in the toolbar
( , for example) shows your sensor
information, the units and current
readings. The details of the dialog
vary, depending on the use of
LabPro, Go!Temp, Go! Link,
Go! Motion, WDSS, spectrometers, GPS or Ohaus balances.
Use the scroll bars in the Sensor Catalogs to view all sensors.
By clicking in a Channel box with a displayed sensor, you may be able to:
Ñ Calibrate a sensor: Perform a new calibration.
Ñ Get sensor information: Includes collection details and calibration information.
Ñ Zero a sensor: Sets the current reading of a sensor to zero.
Ñ Choose sensor: Select another sensor for the channel.
Ñ Change the current settings: Select the available units or calibration settings
Ñ Analog out (CH 4 only): This channel can be used as a function generator.
Ñ Remove sensor: Clears the channel of the sensor.

Manage Your Page and Data

There are numerous ways that you can customize the presentation of your data.

Manage and Adjust Objects

Move Objects Select the object by clicking on it once.
Move the cursor over the edge of the selected object
until the cursor turns into a hand, then hold down the
mouse button while grabbing and moving the object.
Resize Objects Single-click on an object to select it.
When an object is selected, its border becomes visible,
along with eight resizing handles.
Clicking and dragging a resize handle will resize the object
in the appropriate direction.
Graph Axes Customize your graph by changing the columns that are displayed.
1. Position the mouse over the X-axis or Y-axis label and click. A list of
available columns will appear.
2. Select the column you want displayed. If you want more than one column
displayed, select More and check the boxes next to the desired columns.

12
Graph Options Double-click on the graph or select
Graph Options from the Options menu to call up the
Graph Options dialog. This allows you to change the
graph object appearance, including point protectors,
legend, line style, and other graph features. Click the
Axis Options Tab to adjust scaling and select what
columns are plotted or add a Y axis to the right-hand
side of the graph.

Create a Column
You can create a new column that is manually entered
or that consists of calculations based on other data
in Logger Pro. Create a new column by selecting New
Manual Column or New Calculated Column from the
Data menu.

Select and Edit Cells in a Data Table

Manually-entered data and data collected using the Events with Entry mode
can be edited.
Ñ To edit a single cell in a table, single-click in the cell.
Ñ To select a single cell in a table, click and drag the selection within that cell.
Ñ You can select entire columns by clicking on the title of the column.
Ñ You can select an entire row of data by clicking on the row numbers.

The Data Browser

The Data Browser is a container for all data in a
Logger Pro file. In contrast, a given Data Table
will not necessarily show all data columns.
Data Browser Features
Drag and drop from the Data Browser to objects
such as tables and graphs. Drag a column to a
y- or x-axis to plot it there.
When the Data Browser is selected, edit menu
items like Cut, Copy, Paste, etc. will apply to the
selected items within the Data Browser.

13
 Incorporate
videos and
synchronize them
with data you
have collected!
We have included
more than 40
videos, but you
can easily use
your own.

Analyze Data
The Analyze menu contains functions for examining and analyzing your data.
A few of the most commonly used analysis functions include:
Ñ Examine: Shows the x- and y-values of the data point closest to the
mouse pointer.
Ñ Statistics: Calculates the minimum, maximum, mean, and standard deviation.
Ñ Curve Fit: Fits a selected or user-defined function over the data.
Ñ Draw Prediction: Sketch a prediction on a graph using the mouse.
Several of the analysis features are available from the Toolbar.

Additional Analysis Features

Movie: You can synchronize data collection and a movie of the experiment so
that as you Replay the movie, the data are replayed on the graph.
Video Analysis: You can create a graphical representation of the motion
you see in a movie.
Model: Perform a manual curve fit of your data.
Histogram: Displays the distribution of values for a data set in bar graph
format.
Strip Chart: Each new collected data point gets added to the right most
edge of the graph.
FFT: Gives the amplitudes of the frequency components of a data series, and
displays a bar graph showing the amplitudes of the frequencies shown along
the x-axis.

14
Set Preferences
The Preferences dialog box contains several
options that pertain to the general operation
of the software. These preferences will apply
every time Logger Pro is launched.
In Windows, choose Preferences from the File
menu. In Mac OS X, choose Preferences from
the Logger Pro menu.

Printing
Print Graphs and Data
1. Arrange the objects on the screen as you want them to appear on the
paper. If you choose, you can print several graphs and data tables at once.
2. Select Print from the File menu or click on the toolbar.
3. When the printer is ready, click in the Print dialog box.
You can print the graphs and data tables individually by selecting Print Graph
or Print Data Table from the File menu.

Where to Next?
The extensive Help system in Logger Pro provides detailed instructions for
these and other features.
Also available are the Logger Pro Tutorials. Choose Open from the File menu
to access them. These short tutorials are suitable for reference or for use in
your classes. First-time users should work through one introductory tutorial
and the advanced tutorials as needed.
If you have questions as you are using our software, call or e-mail us. We will
be happy to help!

Vernier Software & Technology

13979 SW Millikan Way
Beaverton, OR 97005-2886
toll free 888.837.6437 | fax 503.277.2440
www.vernier.com

15
NOTES

Logger Pro 3, Go! and Vernier LabPro are registered trademarks of

Vernier Software & Technology in the United States of America
Windows and Excel are registered trademarks of Microsoft Corporation.
Quicktime and the Quicktime logo are trademarks or registered trademarks
of Apple Computer, Inc., and are used under license therefrom.
Macintosh and Mac OS are registered trademarks of Apple Computer, Inc.
Palm OS and HotSync are registered Trademarks of Palm, Inc.

16