RKTK Oaqøhv Uewus Ysuk) Ijh (K.K, Oa Fo'Ys"K.K I FR K¡: HKKJRH Ekud

Download as pdf or txt
Download as pdf or txt
You are on page 1of 14

Free Standard provided by BIS via BSB Edge Private Limited to Omega Consultant Services -

kolkata([email protected]) 117.211.70.44 [for non-commercial use only].

Hkkjrh; ekud IS 1199 (Part 3) : 2018

Indian Standard

rktk oaQØhV — uewus ysuk] ijh{k.k


,oa fo'ys"k.k i¼fr;k¡
Hkkx 3 rktk oaQØhV osQ ?kuRo dk fuèkkZj.k
( igyk iqujh{k.k )

Fresh Concrete — Methods of


Sampling, Testing and Analysis
Part 3 Determination of Density of Fresh Concrete

( First Revision )

ICS 91.100.30

© BIS 2018

Hkkjrh; ekud C;wjks


BUREAU OF INDIAN STANDARDS
ekud Hkou] 9 cgknqj'kkg ”kiQj ekxZ] ubZ fnYyh&110002
MANAK BHAVAN, 9 BAHADUR SHAH ZAFAR MARG
NEW DELHI-110002
www.bis.org.in www.standardsbis.in

December 2018 Price Group 5


Free Standard provided by BIS via BSB Edge Private Limited to Omega Consultant Services -
kolkata([email protected]) 117.211.70.44 [for non-commercial use only].

Cement and Concrete Sectional Committee, CED 02

FOREWORD
This Indian Standard (Part 3) (First Revision) was adopted by the Bureau of Indian Standards, after the draft
finalized by the Cement and Concrete Sectional Committee had been approved by the Civil Engineering Division
Council.
Testing plays an important role in controlling the quality of cement concrete work. Systematic testing of the raw
materials, the fresh concrete and the hardened concrete, is an inseparable part of any quality control programme
for concrete. This helps achieve a higher efficiency of the materials used and greater assurance of the performance
of the concrete, in regard to workability, strength and durability. The test methods used should be simple, direct
and convenient to apply. This standard was formulated with this objective in view.
This standard was first published in 1959. In this revision, it was decided to review and update the various
existing test methods of fresh concrete taking into consideration the latest international practices and developments
in this field in the country, and also introduced certain new test methods, wherever required. In the process, the
various existing test methods covered in IS 1199 : 1959 ‘Methods of sampling and analysis of concrete’, have
been revised. The revision of the standard is being brought out taking into consideration primarily the corresponding
ISO Standards while also examining the other best practices world over and in the country. In addition, test
methods for determination of properties of new types of concrete like self compacting concrete have been included,
covering tests such as consistency, viscosity, passing ability and segregation resistance. Also, for better understanding
and implementation, some of the other test methods which were spread over in other Indian Standards have been
brought together under the fold of IS 1199 as its various parts, such as the setting time of concrete by penetration
method and, water soluble and acid soluble chlorides in mortar and concrete. This is with a view to making the
standard complete in all respects, and rendering it a comprehensive source of provisions for testing of concrete
and reference in other Indian Standards.
In this revision, IS 1199 has been split into nine parts. The other parts in the series are:
Part 1 Sampling of fresh concrete
Part 2 Determination of consistency of fresh concrete
Part 4 Determination of air content of fresh concrete
Part 5 Making and curing of test specimens
Part 6 Tests on fresh self compacting concrete
Part 7 Determination of setting time of concrete by penetration resistance
Part 8 Determination of water soluble and acid soluble chlorides in mortar and concrete
Part 9 Analysis of freshly mixed concrete
This standard (Part 3) covers the procedures for determination of density of fresh concrete.
These test methods shall be applicable as and when published in place of the corresponding provisions given in
IS 1199 : 1959. IS 1199 : 1959 shall be superseded after the publication of all the parts of the standard.
This revision of the standard has been taken up to incorporate the modifications found necessary in the light of
experience gained in its use and also to bring it in line with the latest development on the subject. Significant
provisions in this revision are highlighted below:
a) Calculation of cement factor and air content have been deleted from this revision, as they are purely
theoretical in nature.
b) Details on compaction equipment have been covered.

(Continued on third cover)


Free Standard provided by BIS via BSB Edge Private Limited to Omega Consultant Services -
kolkata([email protected]) 117.211.70.44 [for non-commercial use only].

IS 1199 (Part 3) : 2018

Indian Standard
FRESH CONCRETE — METHODS OF SAMPLING,
TESTING AND ANALYSIS
PART 3 DETERMINATION OF DENSITY OF FRESH CONCRETE

( First Revision )
1 SCOPE aggregate size in concrete but shall be not less than
150 mm. The volume of the container shall not be less
This standard (Part 3) specifies procedures for
than 5 litre. The ratio of the diameter to the height of
determination of density of fresh concrete. It also gives
the container shall be 1.25 > dc/hc > 0.5. The measure
the calculation of volume of concrete per batch, and
shall conform to one of the sizes given in Table 1.
yield per bag of cement.
The larger size container given in Table 1 may be
2 REFERENCES suitable for the nominal size of aggregates up to 80
The standards listed in Annex A contain provisions, mm, for still larger sizes of aggregates, bigger
which through reference in this text, constitute containers may be used. Such containers shall be as
provisions of this standard. At the time of publication, per the guidelines given above.
the editions indicated were valid. All standards are The containers shall be calibrated in accordance with
subject to revision and parties to agreements based on Annex B to obtain the volume (V) of the container.
this standard are encouraged to investigate the The containers shall be in calibration at time of use.
possibility of applying the most recent editions of the The frequency of the calibration shall not be less than
standards indicated in Annex A. once in a year.
3 TERMINOLOGY
Table 1 Dimensional Requirements for
For the purpose of this standard, the definitions given Cylindrical Container Used for Measuring
in IS 4845, IS 6461 (Parts 1 to 12) and the following Density of Fresh Concrete
shall apply.
(Clause 4.2.1)
3.1 Density of Fresh Concrete — The mass of a
Sl Nominal Size Inside Inside Minimum
quantity of fully compacted fresh concrete divided by No. of Coarse Diameter Height Thickness of
its volume, expressed in kg/m3. Aggregate Metal
(1) (2) (3) (4) (5)
4 DETERMINATION OF DENSITY OF FRESH
i) Up to 40 250 280 4
CONCRETE ii) Above 40 350 285 5
4.1 Principle 4.2.2 Filling Frame (Optional), made of metal not
The fresh concrete is compacted into a calibrated rigid readily attacked by cement paste, fitted tightly to the
and watertight container and is then weighed. This test container.
method may not be applicable to aerated concrete or 4.2.3 Concrete placed in the container shall be
very stiff concrete that cannot be compacted by normal compacted with one of the following:
vibration and care is needed in its use with these
concretes. a) Internal vibrator, with a minimum frequency
of 120 Hz (7 200 cycles/min). The vibrator
4.2 Apparatus shall meet the requirements of IS 2505.
4.2.1 Container, water tight and sufficiently rigid b) Vibrating table, with a minimum frequency
container, made of metal and not readily attacked by of 50 Hz (3 000 cycles/min). The vibrating
cement paste, having a smooth internal face, with the table shall meet the requirements of IS 2514.
rim machined to a plane surface shall be used. c) Compacting rod, of circular cross-section,
The rim and the base shall be parallel. The smallest straight, made of steel, having a diameter of
dimension of the internal diameter and the height of 16 ±1 mm, a length of 600 ± 5 mm and shall
the container shall be at least four times the maximum have rounded ends.

1
Free Standard provided by BIS via BSB Edge Private Limited to Omega Consultant Services -
kolkata([email protected]) 117.211.70.44 [for non-commercial use only].

IS 1199 (Part 3) : 2018

d) Compacting bar, of square or round cross- compaction of the concrete, with neither excessive
section with mass greater than 1.8 kg for hand segregation nor laitance. Compact each layer by using
compacting. one of the methods described in 4.4.3.2 or 4.4.3.3.
4.2.4 Balance or Scale — It shall be capable of NOTES
determining the mass of the compacted concrete to an 1 Using mechanical vibration, full compaction is achieved when
accuracy of 0.1 percent of the mass of the concrete. there is no further appearance of large air bubbles on the surface
of the concrete and the surface becomes relatively smooth with a
4.2.5 Straight-Edged Scraper — It shall be made of glazed appearance, without excessive segregation.
steel and shall be minimum 100 mm more than the 2 To produce full compaction by hand, the number of strokes per
maximum internal dimensions of the top of the layer required will depend upon the consistence of the concrete.
container.
4.4.3.2 Mechanical vibration
4.2.6 Shovel, of appropriate size.
4.4.3.2.1 Compaction with internal vibrator
4.2.7 Remixing Tray — It shall be of rigid construction
and made from a non-absorbent material not readily Apply the vibration for the minimum duration necessary
attacked by the cement paste. The tray shall be of to achieve full compaction of the concrete. Avoid over
appropriate dimensions such that the concrete can be vibration which may cause loss of entrained air. Care
thoroughly remixed using the square mouthed shovel. shall be taken not to damage the container. The use of
filling frame is recommended.
4.2.8 Trowel, approximately 100 mm wide.
NOTE — Laboratory tests have shown that great care is needed,
4.2.9 Steel Float if loss of entrained air is to be avoided when using an internal
vibrator.
4.2.10 Mallet
Ensure that the vibrator is kept vertical and not allowed
4.3 Sampling to touch the bottom or sides of the container.

The sample for the test shall be obtained in accordance 4.4.3.2.2 Compacting with vibrating table
with IS 1199 (Part 1). The sample shall be properly Apply the vibration for the minimum duration necessary
mixed before carrying out the test. to achieve full compaction of the concrete. The
NOTES container should be attached firmly to the table. The
vibration can be stopped when no more concrete gets
1 When carrying out this test, prevent skin contact with fresh
concrete by wearing suitable protective clothing, gloves and compacted with no laitance on the surface. Avoid over
footwear. If wet cement or concrete enters the eye, immediately vibration, which may cause loss of entrained air.
wash it out thoroughly with clean water and seek medical
treatment without delay. Wash fresh concrete off the skin 4.4.3.3 Hand compaction with compacting rod or bar
immediately.
Distribute the strokes of the compacting rod or bar in a
2 The use of vibrating equipment, such as vibrating tables, can uniform manner over the cross-section of the mould.
cause damage to joints and loss of sensation due to nerve damage.
Moulds, etc, shall be clamped to the table and not held in Ensure that the compacting rod or bar does not forcibly
position using one’s hand while they are being vibrated. strike the bottom of the container when compacting
the first layer, nor penetrate significantly any previous
4.4 Procedure
layers. Subject the concrete to at least 25 strokes per
4.4.1 Mass of the Container layer. In order to remove the pockets of entrapped air
but not the entrained air, after the compaction of each
Weigh the container to determine its mass m1, and
layer, tap the sides of the container smartly with the
record the value indicated.
mallet until large bubbles of air cease to appear on the
4.4.2 Filling the Container surface and depressions left by the compacting rod or
bar are removed.
If a filling frame is used, ensure that the amount of concrete
used to fill the container is such that a layer of concrete 4.4.4 Surface Levelling
remains in the filling frame after compaction, with a
After the top layer has been compacted, smooth level
thickness of 10 percent to 20 percent of the height of the
with the top of the container using the steel float. Skim
container. Fill the concrete in a minimum of two layers.
the surface and rim with the straight edge and wipe
4.4.3 Compacting the Concrete clean the outside of the container.
4.4.3.1 General 4.4.5 Determining the Mass and Volume of the
Container
Compact the concrete immediately after placing it in
the container in such a way as to produce full Weigh the container with its contents to determine its

2
Free Standard provided by BIS via BSB Edge Private Limited to Omega Consultant Services -
kolkata([email protected]) 117.211.70.44 [for non-commercial use only].

IS 1199 (Part 3) : 2018

weight (m2) and record the value indicated. The volume, mT = sum of masses of all the constituents of the
V, of the container shall be determined in accordance concrete as batched, in kg; and
with Annex B. ρfr,c = density of the fully compacted concrete, in
4.5 Test Results kg/m3.
The results shall be expressed to an accuracy of third
The density is calculated from the equation:
decimal digit.
ρfr = (m2 – m1)/V
4.6.3 Yield per Bag of Cement
where
The yield shall be calculated as follows:
ρfr = density of the fresh concrete, in kg/m3;
m1 = mass of the container, in kg; Y = V/N
m2 = mass of the container including the concrete where
in the container, in kg; and
Y = yield of concrete per 50 kg bag of cement,
V = volume of the container, in m3. in m3;
The density of the concrete shall be expressed to the V = volume of concrete produced per batch,
nearest 10 kg/m3. in m3, and;
4.6 Additional Calculations for the Density Test N = number of 50 kg bags of cement per batch.
(Determination of Volume of Concrete per Batch) 4.7 Test Report
4.6.1 General The test report shall include the following:
Once the density of the compacted fresh concrete has a) Identification of the test sample;
been determined, it is possible to use the results to b) Location of performance of test;
calculate, c) Time and date of performance of test;
a) volume of concrete per batch; and d) Ambient temperature;
b) yield per bag of cement. e) Temperature of the remixed sample (optional);
4.6.2 Calculation of Volume of Concrete per Batch f) Observations on condition of test sample
(optional);
The volume of concrete produced per batch shall be g) Any deviation from standard test method;
calculated from the following equation:
h) Calculated density of the fresh concrete, in
mT
Vb = ρ kg/m3;
fr,c
j) Calculated volume of concrete per batch
where (when required); and
Vb = volume of concrete produced per batch, k) Calculated yield per bag of cement (when
in m3; required).

3
Free Standard provided by BIS via BSB Edge Private Limited to Omega Consultant Services -
kolkata([email protected]) 117.211.70.44 [for non-commercial use only].

IS 1199 (Part 3) : 2018

ANNEX A
(Clause 2)
LIST OF REFERRED INDIAN STANDARDS

IS No. Title IS No. Title


1199 (Part 1) : Fresh concrete — Methods of (Part 2) : 1972 Materials (Other than cement and
2018 sampling, testing and analysis: aggregate)
Part 1 Sampling of fresh concrete (Part 3) : 1972 Concrete reinforcement
(first revision) (Part 4) : 1972 Types of concrete
2505 : 1992 Concrete vibrators — Immersion (Part 5) : 1972 Formwork for concrete
type — General requirements (Part 6) : 1972 Equipment, tools and plant
(third revision) (Part 7) : 1973 Mixing, laying, compaction,
2514 : 1963 Specification for concrete curing and other construction
vibrating tables aspects
4845 : 1968 Definitions and terminology (Part 8) : 1973 Properties of concrete
relating to hydraulic cement (Part 9) : 1973 Structural aspects
6461 Glossary of terms relating to (Part 10) : 1973 Tests and testing apparatus
cement concrete (Part 11) : 1973 Prestressed concrete
(Part 1) : 1972 Concrete aggregates (Part 12) : 1973 Miscellaneous

ANNEX B
(Clauses 4.2.1and 4.4.5)
CALIBRATION OF CONTAINERS FOR THE DENSITY TEST

B-1 APPARATUS it to exclude any air bubbles. Remove any excess water
from the outside of the container plate.
B-1.1 Scales or Balance — It shall be capable of
weighing the container either empty or full of water to Weigh the container, glass plate and water to an
an accuracy of 0.1percent. accuracy of 0.1 percent and record the indicated mass.

B-1.2 Glass Plate — Circular or square plate with a Calculate the volume of the container by dividing the
minimum thickness of 5 mm, and it shall extend 25 mm total mass, expressed in kilograms, of water required
on each side. to fill the container by 996.5.
Express the volume, V, expressed in cubic metres of
B-2 PROCEDURE the container to an accuracy of 0.1 percent.
Weigh the empty container and glass plate to an B-3 CALIBRATION INTERVAL
accuracy of 0.1 percent and record the indicated mass.
The container shall be calibrated before initial use and
Place the container on a horizontal surface and fill with at least annually thereafter. It is recommended that the
water at a temperature of 27 ± 2°C. The container shall balance be calibrated at least annually. The frequency
be filled to overflowing level and glass plate slid over may be increased based on usage or repair.

4
Free Standard provided by BIS via BSB Edge Private Limited to Omega Consultant Services -
kolkata([email protected]) 117.211.70.44 [for non-commercial use only].

IS 1199 (Part 3) : 2018

ANNEX C
(Foreword)
COMMITTEE COMPOSITION
Cement and Concrete Sectional Committee, CED 02

Organization Representative(s)
In Personal Capacity (14A, Summer Breeze, Kuravankonam, SHRI J OSE KURIAN (Chairman)
Kowdiar, Thiruvananthapuram 695 003)
ACC Ltd, Mumbai SHRI S. A. KHADILKAR
SHRI RAMAN SADANAND P ARULEKAR (Alternate)
Ambuja Cements Limited, Ahmedabad SHRI J. P. DESAI
DR BIBEKANANDA MOHAPATRA (Alternate)
Atomic Energy Regulatory Board, Mumbai SHRI L. R. BISHNOI
SHRI SOURAV ACHARYA (Alternate)
Builders’ Association of India, Mumbai SHRI S USHANTA KUMAR BASU
SHRI D. R. SEKOR (Alternate)
Building Materials and Technology Promotion Council, New Delhi SHRI J. K. PRASAD
SHRI C. N. JHA (Alternate)
Cement Manufacturers’ Association, Noida SHRI RAKESH BHARGAVA
DR S. K. HANDOO (Alternate)
Central Public Works Department, New Delhi SHRI A. K. GARG
SHRI RAJESH KHARE (Alternate)
CSIR – Central Building Research Institute, Roorkee SHRI S. K. S INGH
SHRI S UBHASH GURRAM (Alternate)
CSIR – Central Road Research Institute, New Delhi SHRI J. B. SENGUPTA
SHRI SATISH PANDEY (Alternate)
CSIR – Structural Engineering Research Centre, Chennai DR K. R AMANJANEYULU
DR P. SRINIVASAN (Alternate)
Central Soil and Materials Research Station, New Delhi DIRECTOR
SHRI N. S IVA KUMAR (Alternate)
Central Water Commission, New Delhi DIRECTOR (CMDD) (N&W)
DEPUTY DIRECTOR (CMDD) (NW&S) (Alternate)
Conmat Technolgies Pvt Ltd, Kolkata DR A. K. C HATTERJEE
SHRI SUBRATO CHOWDHURY (Alternate)
Construction Chemical Manufacturers’ Association, Mumbai SHRI S AMIR SURLAKER
SHRI NILOTPOL KAR (Alternate)
Delhi Development Authority, New Delhi SHRI LAXMAN SINGH
SHRI VIJAY SHANKAR (Alternate)
Department of Science and Technology, Ministry of Science SHRI CHANDER M OHAN
and Technology, New Delhi
Engineers India Limited, New Delhi SHRI R AJANJI SRIVASTAVA
SHRI ANURAG SINHA (Alternate)
Gammon India Limited, Mumbai SHRI V. N. H EGGADE
SHRI S. C. UPADHYAY (Alternate)
Hindustan Construction Company Limited, Mumbai SHRI SATISH KUMAR S HARMA
DR CHETAN HAZAREE (Alternate)
Housing and Urban Development Corporation Limited, New Delhi SHRI DEEPAK B ANSAL
Indian Association of Structural Engineers, New Delhi SHRI M AHESH TANDON
SHRI GANESH JUNEJA (Alternate)
Indian Concrete Institute, Chennai SHRI VIVEK NAIK
SECRETARY GENERAL (Alternate)
Indian Institute of Technology Delhi, New Delhi REPRESENTATIVE
Indian Institute of Technology Madras, Chennai PROF DEVDAS MENON
DR MANU S ANTHANAM (Alternate)

5
Free Standard provided by BIS via BSB Edge Private Limited to Omega Consultant Services -
kolkata([email protected]) 117.211.70.44 [for non-commercial use only].

IS 1199 (Part 3) : 2018

Organization Representative(s)
Indian Institute of Technology Roorkee, Roorkee PROF V. K. GUPTA
DR BHUPINDER SINGH (Alternate)
Indian Roads Congress, New Delhi SECRETARY G ENERAL
DIRECTOR (Alternate)
Institute for Solid Waste Research and Ecological Balance, DR N. B HANUMATHIDAS
Visakhapatnam SHRI N. KALIDAS (Alternate)
Military Engineer Services, Engineer-in-Chief’s Branch, MAJ GEN S. K. SRIVASTAV
Army HQ, New Delhi SHRI MAN SINGH (Alternate)
Ministry of Road Transport and Highways, New Delhi SHRI A. P. PATHAK
SHRI A. K. P ANDEY (Alternate)
National Council for Cement and Building Materials, Ballabgarh SHRI V. V. ARORA
DR S. HARSH (Alternate)
National Test House, Kolkata SHRI SHIR S INGH
SHRIMATI S. A. KAUSHIL (Alternate)
Nuclear Power Corporation of India Ltd, Mumbai SHRI ARVIND SHRIVASTAVA
SHRI RAGHUPATI ROY (Alternate)
Nuvoco Vistas Corporation Limited, Mumbai SHRI PRANAV DESAI
SHRI RAVINDRA KHAMPARIA (Alternate)
OCL India Limited, New Delhi DR S. C. AHLUWALIA
Public Works Department, Govt of Tamil Nadu, Chennai SUPERINTENDING ENGINEER
EXECUTIVE ENGINEER (Alternate)
The India Cements Limited, Chennai DR D. VENKATESWARAN
The Indian Hume Pipe Company Limited, Mumbai SHRI P. R. BHAT
SHRI S. J. SHAH (Alternate)
The Institution of Engineers (India), Kolkata DR H. C. VISVESVARAYA
SHRI S. H. JAIN (Alternate)
The Ramco Cements Limited, Chennai SHRI BALAJI K. MOORTHY
SHRI ANIL KUMAR PILLAI (Alternate)
Ultra Tech Cement Ltd, Mumbai SHRI S URYA VALLURI
DR M. R. KALGAL (Alternate)
Voluntary Organization in Interest of Consumer Education, SHRI M. A. U. KHAN
New Delhi SHRI B. MUKHOPADHYAY (Alternate)
In personal capacity [B-806, Oberoi Exquisite, Oberoi Garden SHRI A. K. J AIN
City, Goregaon (East), Mumbai]
In personal capacity (36, Old Sneh Nagar, Wardha Road, Nagpur) SHRI L. K. J AIN
In personal capacity (EA-92, Maya Enclave, Hari Nagar, SHRI R. C. WASON
New Delhi)
In personal capacity (E-1, 402, White House Apartments, SHRI S. A. REDDI
R. T. Nagar, Bengaluru)
BIS Directorate General SHRI S ANJAY P ANT, Scientist ‘F’ and Head (Civil Engg)
[Representing Director General (Ex-officio)]

Member Secretary
SHRIMATI DIVYA S.
Scientist ‘B’ (Civil Engg), BIS

Concrete Sub-committee, CED 2:2


Organization Representative(s)

In Personal Capacity, (14A, Summer Breeze, Kuravankonam, SHRI J OSE KURIAN (Convener)
Kowdiar, Thiruvananthapuram 695 003)
ACC Limited, Mumbai SHRI AVIJIT CHAUBEY (Alternate)
Ambuja Cement Limited, Ahmedabad SHRI J. P. DESAI
DR BIBEKANANDA MOHAPATRA (Alternate)
Association of Consulting Civil Engineers (India), Bengaluru SHRI AVINASH D. S HIRODE
SHRI K. K. MEGHASHYAM (Alternate)

6
Free Standard provided by BIS via BSB Edge Private Limited to Omega Consultant Services -
kolkata([email protected]) 117.211.70.44 [for non-commercial use only].

IS 1199 (Part 3) : 2018

Organization Representative(s)
Atomic Energy Regulatory Board, Mumbai SHRI L. R. BISHNOI
SHRI SOURAV ACHARYA (Alternate)
Building Materials and Technology Promotion Council, New Delhi SHRI J. K. PRASAD
SHRI PANKAJ GUPTA (Alternate)
Bureau of Design for Hydel and Irrigation Project, Bhopal SHRI S. K. KHARE
SHRI BHAGWATI P RASAD GUPTA (Alternate)
Central Public Works Department, New Delhi SHRI A. K. GARG
SHRI RAJESH KHARE (Alternate)
Civil-Aid Technoclinic Pvt Ltd, Bengaluru SHRI M. S. SUDARSHAN
SHRI R. NAGENDRA (Alternate)
Creative Design Consultants and Engineers Pvt Ltd, Ghaizabad SHRI AMAN D EEP
CSIR – Central Building Research Institute, Roorkee DR RAJESH DEOLIA
SHRI H. C. Arora (Alternate)
CSIR – Central Road Research Institute, New Delhi SHRI J. B. S ENGUPTA
SHRI SATISH PANDEY (Alternate)
CSIR – Central Soil & Materials Research Station, New Delhi SHRI R AJEEV K UMAR
SHRI M. RAJA (Alternate)
CSIR–Structural Engineering Research Centre, Chennai DR B. H. BHARATH K UMAR
DR P. SRINIVASAN (Alternate)
Department of Science and Technology, Ministry of Science SHRI CHANDER M OHAN
and Technology, New Delhi
Elkem South Asia Pvt Ltd, Navi Mumbai SHRI BRAJESH MALVIYA
SHRI S URENDRA S HARMA (Alternate)
Engineers India Limited, New Delhi SHRI RAJANJI SRIVASTAVA
SHRI ANURAG SINHA (Alternate)
Gammon India Limited, Mumbai SHRI M ANISH M OKAL
SHRI SUDEESH RAJENDRAN (Alternate)
Hindustan Constrution Company Ltd, Mumbai DR CHETAN HAZARE
SHRI AVINASH HARDE (Alternate)
Indian Concrete Institute, Chennai SHRI K. C. TAYADE
SECRETARY GENERAL (Alternate)
Indian Institute of Structural Engineering, Mumbai SHRI D. S. JOSHI
SHRI HEMANT VADALKAR (Alternate)
Indian Institute of Technology Delhi, New Delhi DR B. BHATTACHARJEE
DR SHASHANK BISHNOI (Alternate)
Indian Institute of Technology Kanpur, Kanpur DR SUDHIR M ISHRA
Indian Institute of Technology Madras, Chennai DR MANU S ANTHANAM
Indian Institute of Technology Roorkee, Roorkee DR ASHOK KUMAR JAIN
Indian Society of Structural Engineers, Mumbai SHRI D. S. JOSHI
SHRI HEMANT VADALKAR (Alternate)
Irrigation and Power Research Institute, Amritsar CHIEF ENGINEER (RESEARCH)
RESEARCH OFFICER (Alternate)
Larsen and Toubro Limited, ECC Division, Chennai DR B. SIVARAM S ARMA
SHRI S. MANOHAR (Alternate)
Military Engineer Services, Engineer-in-Chief’s Branch, SHRI S. K. S RIVASTAV
Army HQ, New Delhi SHRI MAN SINGH (Alternate)
Ministry of Road Transport & Highways, New Delhi SHRI A. P. PATHAK
SHRI A. K. P ANDEY (Alternate)
National Buildings Construction Corporation Limited, Haryana SHRI H. S. YADAV
SHRI PAWAN KUMAR (Alternate)
National Council for Cement & Building Materials, Ballabgarh SHRI V. V. ARORA
SHRI S. SHARMA (Alternate)
National Institute of Technology, Warangal DR C. B. KAMESWARA RAO
DR D RAMA SESHU (Alternate)

7
Free Standard provided by BIS via BSB Edge Private Limited to Omega Consultant Services -
kolkata([email protected]) 117.211.70.44 [for non-commercial use only].

IS 1199 (Part 3) : 2018

Organization Representative(s)
Nuclear Power Corporation of India Limited, Mumbai SHRI ARVIND S HRIVASTAVA
SHRI N. M. RAO (Alternate)
Pidilite Industries Limited, Mumbai DR SUGUNA NAIK
Ready Mixed Concrete Manufacturers’ Association, Mumbai SHRI VIJAYKUMAR R. KULKARNI
SHRI ANIL KULKARNI (Alternate)
Research, Design & Standards Organization (Ministry of Railways), JOINT DIRECTOR (B&S)/CB-I
Lucknow JOINT DIRECTOR (B&S)/CB-II (Alternate)
Shapoorji Pallonji and Company Private Limited, Mumbai SHRI GIRISH BONDE
SHRI D. N. VISHWANATH (Alternate)
Tandon Consultants Pvt Limited, New Delhi SHRI M AHESH TANDON
SHRI VINAY GUPTA (Alternate)
Tata Consulting Engineers Limited, Mumbai SHRI S. N. DIWAKAR
SHRI MANOS KUMAR DE (Alternate)
Ultra Tech Cement Ltd, Mumbai DR V. RAMACHANDRA
DR A. K. S INGH (Alternate)
Water Resource Department, Govt of Madhya Pradesh, Mumbai SHRI S. K. KHARE
SHRI B. P. G UPTA (Alternate)
In personal capacity (452 Sector 14, Sonipat, Haryana) SHRI R. K. J AIN
In personal capacity (36, Old Sneh Nagar, Wardha Road, Nagpur) SHRI L. K. J AIN
In personal capacity [B-806, Oberoi Exquisite, Oberoi Garden SHRI A. K. J AIN
City, Goregaon (East), Mumbai]
In personal capacity (EA-92, Maya Enclave, Hari Nagar, SHRI R. C. WASON
New Delhi)
In personal capacity (E-1, 402, White House Apartments, SHRI S. A. REDDI
R.T. Nagar, Bengaluru)
In personal capacity (M1 F1 VGN Minerva Apartments, DR C. RAJKUMAR
Guruswamy Road, Nolambur, Chennai)

Panel for Revision of Indian Standards on Test Methods for Concrete, CED 2:2/P7

Organization Representative(s)

In Personal Capacity (EA-92, Maya Enclave, Hari Nagar, SHRI R. C. WASON (Convener)
New Delhi 110064)
ACC Limited, Mumbai REPRESENTATIVE
AIMIL Ltd, New Delhi DR V. M. SHARMA
Central Public Works Department, New Delhi SHRI AJAY P RAKASH MATHUR
SHRI RAJESH KHARE (Alternate)
Central Soil and Materials Research Station, New Delhi SHRI U. S. VIDYARTHI
Civil-Aid Technoclinic Pvt Ltd, Bengaluru DR R. NAGENDRA
SHRI SUNIL V. SONNAD (Alternate)
CSIR – Central Building Research Institute, Roorkee DR A. K. P ANDEY
SHRI S. K. SINGH (Alternate)
CSIR – Central Road Research Institute, New Delhi REPRESENTATIVE
CSIR – Structural Engineering Research Centre, Chennai DR P. S RINIVASAN
DR S. BHASKAR (Alternate)
Hindustan Construction Company Ltd, Mumbai DR CHETAN H AZAREE
SHRI AVINASH HARDE (Alternate)
Hydraulic & Engineering Instrument, New Delhi REPRESENTATIVE
Indian Concrete Institute, New Delhi SHRI ASHOK KUMAR TIWARI
Indian Institute of Technology Madras, Chennai DR RADHAKRISHNA PILLAI
DR RAVINDRA GETTU (Alternate)
Indian Institute of Technology Delhi, New Delhi DR SHASHANK BISHNOI
DR S. GUPTA (Alternate)

8
Free Standard provided by BIS via BSB Edge Private Limited to Omega Consultant Services -
kolkata([email protected]) 117.211.70.44 [for non-commercial use only].

IS 1199 (Part 3) : 2018

Organization Representative(s)
Larsen & Toubro Ltd, ECC Division, Chennai SHRI B. S IVARAMA SARMA
SHRI S. MANOHAR (Alternate)
National Council for Cement and Building Materials, Ballabgarh SHRI V. V. ARORA
SHRI S. C. S HARMA (Alternate)
Nuclear Power Corporation of India Ltd, Mumbai SHRI ARVIND S HRIVASTAVA
SHRI A. K. LAHARIA (Alternate)
RDC Concrete (India) Pvt Ltd, Mumbai SHRI K. TAGORE
SHRI V. MEIKANDA MOORTHY (Alternate)
Ready Mixed Concrete Manufacturers’ Association, Mumbai SHRI VIJAYKUMAR R. KULKARNI
SHRI JEAN P HILIPPE THIERRY (Alternate)
In personal capacity (50 Mangla Apartments Kalkaji, New Delhi) DR S. C. MAITI
In personal capacity (Type IV/17, President’s Estate, New Delhi) SHRI K. H. B ABU

9
Free Standard provided by BIS via BSB Edge Private Limited to Omega Consultant Services -
kolkata([email protected]) 117.211.70.44 [for non-commercial use only].
Free Standard provided by BIS via BSB Edge Private Limited to Omega Consultant Services -
kolkata([email protected]) 117.211.70.44 [for non-commercial use only].

(Continued from second cover)

In the formulation of this standard, assistance has also been derived from ISO 1920-2 : 2016, ‘Testing of
concrete — Part 2: Properties of fresh concrete’.
The composition of the Committee responsible for the formulation of this standard is given in Annex C.
In reporting the result of a test or analysis made in accordance with this standard, if the final value observed or
calculated, is to be rounded off, it shall be done in accordance with IS 2 : 1960 ‘Rules for rounding off numerical
values (revised)’.
Free Standard provided by BIS via BSB Edge Private Limited to Omega Consultant Services -
kolkata([email protected]) 117.211.70.44 [for non-commercial use only].

Bureau of Indian Standards

BIS is a statutory institution established under the Bureau of Indian Standards Act, 2016 to promote
harmonious development of the activities of standardization, marking and quality certification of goods
and attending to connected matters in the country.

Copyright

BIS has the copyright of all its publications. No part of these publications may be reproduced in any form
without the prior permission in writing of BIS. This does not preclude the free use, in the course of
implementing the standard, of necessary details, such as symbols and sizes, type or grade designations.
Enquiries relating to copyright be addressed to the Director (Publications), BIS.

Review of Indian Standards

Amendments are issued to standards as the need arises on the basis of comments. Standards are also reviewed
periodically; a standard along with amendments is reaffirmed when such review indicates that no changes are
needed; if the review indicates that changes are needed, it is taken up for revision. Users of Indian Standards
should ascertain that they are in possession of the latest amendments or edition by referring to the latest issue of
‘BIS Catalogue’ and ‘Standards : Monthly Additions’.

This Indian Standard has been developed from Doc No.: CED 02 (10890).

Amendments Issued Since Publication

Amend No. Date of Issue Text Affected

BUREAU OF INDIAN STANDARDS


Headquarters:
Manak Bhavan, 9 Bahadur Shah Zafar Marg, New Delhi 110002
Telephones : 2323 0131, 2323 3375, 2323 9402 Website: www.bis.org.in

Regional Offices: Telephones


Central : Manak Bhavan, 9 Bahadur Shah Zafar Marg
NEW DELHI 110002 { 2323 7617
2323 3841
Eastern : 1/14 C.I.T. Scheme VII M, V. I. P. Road, Kankurgachi
KOLKATA 700054 { 2337 8499, 2337 8561
2337 8626, 2337 9120
Northern : Plot No. 4-A, Sector 27-B, Madhya Marg, CHANDIGARH 160019
{ 26 50206
265 0290
Southern : C.I.T. Campus, IV Cross Road, CHENNAI 600113
{ 2254 1216, 2254 1442
2254 2519, 2254 2315
Western : Manakalaya, E9 MIDC, Marol, Andheri (East)
MUMBAI 400093 { 2832 9295, 2832 7858
2832 7891, 2832 7892
Branches: A H M E D A B A D . B E N G A L U R U . B H O PA L . B H U B A N E S WA R . C O I M B ATO R E .
D E H R A D U N . D U R G A P U R . FA R I D A B A D . G H A Z I A B A D . G U WA H AT I .
HYDERABAD. JAIPUR. JAMMU. JAMSHEDPUR. KOCHI. LUCKNOW. NAGPUR.
PA RWA N O O . PAT N A . P U N E . R A I P U R . R A J K O T. V I S A K H A PAT N A M .
Published by BIS, New Delhi

You might also like