UCJV300 Multilayer Printing Guide
UCJV300 Multilayer Printing Guide
Note
• It is strictly prohibited to write or copy a part or whole of this document without our approval.
• The contents of this document may be subject to change without notice.
• Due to improvement or change of this software, the description of this document could be partially different in
specification, for which your understanding is requested.
• It is strictly prohibited to copy this software to other disk (excluding the case for making backup) or to load on the
memory for the purpose other than executing it.
• With the exception of what is provided for in the warranty provisions of MIMAKI ENGINEERING CO., LTD., we
do not assume any liability against the damages (including but not limited to the loss of profit, indirect damage,
special damage or other monetary damages) arisen out of the use or failure to use of this product. The same
shall also apply to the case even if MIMAKI ENGINEERING CO., LTD. had been notified of the possibility of aris-
ing damages in advance. As an example, we shall not be liable for any loss of the media (works) made using this
product or indirect damages caused by the product made using this media.
Adobe, Photoshop, Illustrator and PostScript are trademarks of Adobe Systems Incorporated.
Apple, Macintosh, Mac OSX and macOS are registered trademarks of Apple Inc.
Microsoft, Windows, Windows 7, Windows 8.1 or Windows 10 All trademarks of Microsoft used in this document
are trademarks or registered trademarks of the Microsoft Corporation and its related companies in Canada, the
United States and/or other countries.
All brand names and product names are trademarks or registered trademarks of their respective companies.
TABLE OF CONTENTS
Note ............................................................................................................................ 1
What is Multilayer Printing? ..................................................................................... 2
4 Layers Printing ....................................................................................................... 3
4 layers printing - about Day & Night ................................................................................... 4
Functions of software (4 layers) ............................................................................................ 5
Creating and printing procedures of 4 layers data .............................................................. 6
With RasterLinkTools ............................................................................................................ 6
Without RasterLinkTools ..................................................................................................... 10
Troubleshooting (4 layers) ................................................................................................... 14
-2-
4 Layers Printing
-3-
4 layers printing - about Day & Night
By overprinting a total of 4 layers of front color + white + black (light shielding) + background color, the back-
ground picture will appear on the front through when light is applied from the back.
Making use of this effect can change the impression of the picture between when the light is on and off.
Media
White
Front
1
2
3 By lighting from the back side, the
background picture will appear on the
4 front through.
Back (1st layer): a picture to show on the front when light is applied
Black (2nd layer): does not display the back picture when light is not applied
White (3rd layer): makes the front color shine, and hides the black layer
Front (4th layer): a picture usually shown
Media 1 2 3 4
Light is off
Light is on
Side view
1st layer print 2nd layer print 3rd layer print 4th layer print
The layer for printing a Black-filled layer. White-filled layer. The layer for printing a
picture shown when The layer to hide the The layer to hide the picture shown when
light is applied from 1st layer picture when 2nd black layer to light is not applied.
the back. light is not applied. make the color of the
Also called a 4th layer shine.
light-shielding layer.
-4-
Functions of software (4 layers)
The following software products are used for 4 layers printing:
Illustrator
• Creation of front and back layers
Use to create a front layer (a picture usually shown) and a back layer (a picture to show when light is
applied).
RasterLinkTools
• Automatic creation of white and black layers
Automatically create white and black layers required for 4 layers printing.
• Preview
Display the finished image of 4 layers printing data.
(Preview function is supported for only 4 layers printing.)
RasterLink6Plus
• Create a composition job of multi-layer and print it.
-5-
Creating and printing procedures of 4 layers data
With RasterLinkTools
The following describes the procedure to configure settings required for 4 layers printing with RasterLinkTools.
Use the simplest procedure of "solid white and black layers" for the steps from "data creation" to "print of cre-
ated data".
-6-
1. Create front and back layers. (Illustrator)
• Create single layer data for each of the
front and back layers.
Merge any multiple layers for each layer.
• Make sure to arrange the pictures in the order shown in the figure above. (Otherwise, 4 layers
printing does not function properly.)
• There is no restriction on layer names.
-7-
3. The preview is displayed. (RasterLinkTools)
• Select the [Multilayer Printing
function] icon .
• Note that the preview function cannot perfectly represent the actual print data.
-8-
5. Print the created data. (RasterLink6Plus)
(1) After saving the created 4 layers
data files in the hot folder, a job is
composed.
1
(2) Select the [Execute] icon .
(3) Press the [Start] button to start print- 2
ing.
3
• You can change the print setting of a composition job in 4 layers printing. However, you cannot
specify individual print setting for each layer.
-9-
Without RasterLinkTools
The following describes the procedure to configure settings required for 4 layers printing with only
RasterLink6Plus and without RasterLinkTools.
• If you created data with any method other than P.6 "With RasterLinkTools", you have to configure the
settings manually because the settings required for 4 layers printing are not made automatically.
- 10 -
1. Load the 4 layers printing data into RasterLink6Plus.
You can use one of the following two procedures for loading data:
• In RasterLinkTools, if you created the white layer by using the automatic creation function of
white and black layers, the white layer is created in yellow. Select Yellow into White in "Mono
color replacement " as shown in the image above to print the white layer.
• If you create the white layer by using "Color replacement ", only "Mono color -> White" is
possible.
Note that "Multiple colors -> White" in "Color replacement " is impossible only for Multilayer
Printing.
- 11 -
3. Configure the print setting for the black layer.
1
(1) Select the [Properties] icon .
(2) Set the job attribute to
[Light-shielding layer].
(This option is available for only jobs
with color attribute.)
■ 4th layer
Farthest layer
4th
from the media
3rd
2
2nd
• You cannot specify individual print setting for each layer. (ex. changing the resolution on the
white layer only is impossible)
• The print settings (profile, resolution, etc.) on the top job are also used on other jobs being
composited.
- 12 -
5. Set the positional correction of data after composition. (optional)
• If any positional correction is required, select the [layer setting] icon .
The positional correction for each layer is now configurable. Make settings as necessary.
• You can change the print setting of a composition job in 4 layers printing. However, you cannot
specify individual print setting for each layer.
- 13 -
Troubleshooting (4 layers)
The following describes additional information for creating 4 layers data.
RasterLinkTools
Preview does not appear, or the preview display is wrong.
Check the order and numbers of layers.
The order and numbers of layers are correct, but the preview display is
wrong.
For complicated pictures, the preview may not function correctly. However, a print can succeed. Try a test
print.
You want to create white and black layers without a solid fill.
The automatic creation function of white and black layers in RasterLinkTools is used to automatically create
white and black layers with a solid fill.
Create white and black layers without a solid fill manually if you need them.
Why is the density for the automatically created black layer set to Black 30%?
According to our test results, the optimal density of Black was 30%, so it is set for the automatically created black layer.
However, the optimal density may change depending on the environment. Try to change the density as necessary.
RasterLink6Plus
*1. The special color machine is designed to use two units of white as standard. So when you print, use the
two units of white if possible. The auto setting is configured to use the two units of white.
- 14 -
The part of the picture you want to enhance is not highlighted when light is
applied from back.
The simplest structure is the solid black layer for 4 layers printing(Day & Night). However, different
expression is achieved than a solid fill by adding more steps on the black layer data.
The following describes an example in which a part of the black layer is cut out to show the target part vivid
and highlighted.
The daylight landscape printed on the top layer is By lighting from the back side, the different
shown when light is not applied. dress color and background printed on the bot-
tom layer will appear.
Media
Transparent media
- 15 -
About mirror output procedure
You can use one of the following two procedures to make the picture inverted for mirror output.
1. Inverting with RasterLinkTools
2. Inverting with RasterLink6Plus
• This function is valid only when the file is saved in RasterLinkTools and saved to the hot folder
in RasterLink6Plus.
■ 4th layer
Farthest layer
from the media 4th
3rd
2, 3
2nd
■ 1st layer
Nearest layer 1st
from the media 1
4
5
- 16 -
What is the condition for automatically making settings required for 4 layers
printing?
Start operation
- 17 -
5 Layers Printing
- 18 -
About 5 layers printing
By overprinting a total of 5 layers of "color (front) + white + color (light-shielding) + white + color (back)", different
pictures can be shown on the front and back on a sheet of media.
Media
Back
White 1 Back Front
Black
White 2
1
Front
2
3
Different pictures shown on
4
the front and back
5
Back (1st layer): a picture seen through the media
White 1 (2nd layer): hides the black layer and makes the back color shine
Black (3rd layer): the layer for light-shielding the front and back pictures
White 2 (4th layer): the layer to hide the black layer and make the front color shine
Front (5th layer): a picture seen from the media
1st layer print 2nd layer print 3rd layer print 4th layer print 5th layer print
The layer for printing White-filled layer. Black-filled layer. White-filled layer. The layer for
a picture on the The layer to hide The layer to prevent The layer to hide printing a picture
back side. the 3rd black layer the pictures on the the 3rd black layer on the front side.
to make the color 1st and 5th layers to make the color
of the 1st layer from being seen of the 5th layer
shine. through. Also called shine.
a light-shielding
layer.
- 19 -
Functions of software (5 layers)
The following software products are used for 5 layers printing for the steps from "data creation" to "print of cre-
ated data".
Illustrator
• Creation of front and back layers
Use to create a front layer (a picture seen from the media) and a back layer (a picture seen through the
media).
RasterLinkTools
• Automatic creation of white and black layers
Automatically create white and black layers required for 5 layers.
RasterLink6Plus
• Create a composition job of Multi-layer and print it.
- 20 -
Creating and printing procedures of 5 layers data
With RasterLinkTools
The following describes the procedure to configure settings required for 5 layers printing with RasterLinkTools.
- 21 -
1. Create front and back layers. (Illustrator)
• Create single layer data for each of the
front and back layers.
Merge any multiple layers for each layer.
• Make sure to arrange the pictures in the order shown in the figure above. (Otherwise, 5 layers
printing does not function properly.)
• Place the picture printed on the media side on the 1st layer.
• You do not have to create an inverted picture on the 1st layer (through media).
• There is no restriction on layer names.
- 22 -
3. Save the created data. (RasterLinkTools)
• Select the [Multilayer Printing function]
icon .
• Press the [Output] button to save the 5
layers data.
A single file for a single layer, five files in
total are saved.
• You can change the print setting of a composition job in 5 layers printing. However, you cannot
specify individual print setting for each layer.
- 23 -
Without RasterLinkTools
The following describes the procedure to configure settings required for 5 layers printing with only Raster-
Link6Plus and without RasterLinkTools.
• If you created data with any method other than P.21 "With RasterLinkTools", you have to config-
ure the settings manually because the settings required for 5 layers printing are not made auto-
matically.
- 24 -
1. Load the 5 layers printing data into RasterLink6Plus. (RasterLink6Plus)
You can use one of the following two procedures for loading data:
• For 5 layers printing, we recommend that the white layer is printed with the 200% setting (two
units of white). Make the setting same as the image above.
Making the setting to white 200% can increase the degree of light-shielding (preventing the
picture from being seen through) without increasing the density of black.
• In RasterLinkTools, if you created the white layer by using the automatic creation function of
white and black layers, the white layer is created in yellow. Select Yellow into White in "Mono
color replacement " as shown in the image above to print the white layer.
• If you create the white layer by using "Color replacement ", only "Mono color -> White" is possible.
Note that "Multiple colors -> White" in "Color replacement " is impossible only for Multilayer Printing.
- 25 -
3. Configure the print setting for the black layer.
1
(1) Select the [Properties] icon .
(2) Set the job attribute to [Light-shield-
ing layer].
(This option is available for only jobs
with color attribute.)
• If the picture on the media side needs to be inverted, follow the steps (3) and (4).
(3) Select the 1st layer data.
(4) Select the [Mirror] check box in the Composite option. The picture on the 1st layer is inverted.
• Inverted is the normal state for the picture on the 1st layer data.
• If the picture has been already inverted when created, now you do not have to select the check
box.
■ 5th layer
Farthest layer
from the media 5th
4th
3rd 2
2nd
■ 1st layer 1
Nearest layer
from the media 1st 3
4
5
- 26 -
5. Set the positional correction of data after composition. (optional)
• If any positional correction is required, select the [layer setting] icon .
The positional correction for each layer is now configurable. Make settings as necessary.
• You can change the print setting of a composition job in 5 layers printing. However, you cannot
specify individual print setting for each layer.
- 27 -
Troubleshooting (5 layers)
The following describes additional information for creating 5 layers data.
RasterLinkTools
Preview does not appear
Preview display is supported for only 4 layers.
You want to create white and black layers without a solid fill.
The automatic creation function of white and black layers in RasterLinkTools is used to automatically create
white and black layers with a solid fill.
Create white and black layers without a solid fill manually if you need them.
Why is the density for the automatically created black layer set to Black
100%?
The density for the black layer is set to Black 100%, the highest degree of light-shielding, so that the back
and front pictures do not seen through to each other.
RasterLink6Plus
Is the profile exclusive for 5 layers printing necessary?
You do not have to prepare the profile exclusive for 5 layers printing.
Use the profile of WhiteOnColor for the media to be printed.
- 28 -
- 29 -
D203254-10-01122017
© MIMAKI ENGINEERING CO., LTD.2017 HK