Scribd
Upload
129 views2 pages

How Do I Setup A Layer 3 Network With Static Routes On My Dgs-3324Sr/ Dgs-3324Sri/Dxs-3350Sr/Dxs-3326Gsr?

This document provides instructions for configuring static routes on D-Link switches to allow communication between different subnets located on two switches. It describes creating VLANs and IP interfaces for subnets on each switch and adding static routes between the switches to route traffic to remote subnets. The configuration is tested by pinging hosts across subnets located on different switches.

Uploaded by

luke skywalker
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
129 views2 pages

How Do I Setup A Layer 3 Network With Static Routes On My Dgs-3324Sr/ Dgs-3324Sri/Dxs-3350Sr/Dxs-3326Gsr?

This document provides instructions for configuring static routes on D-Link switches to allow communication between different subnets located on two switches. It describes creating VLANs and IP interfaces for subnets on each switch and adding static routes between the switches to route traffic to remote subnets. The configuration is tested by pinging hosts across subnets located on different switches.

Uploaded by

luke skywalker
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

How do I setup a Layer 3 network with Static Routes on my DGS-3324SR/DGS-3324SRi/DXS-3350SR/DXS-3326GSR?

Page 1

How do I setup a Layer 3 network with Static Routes on my DGS-3324SR/


DGS-3324SRi/DXS-3350SR/DXS-3326GSR?
Warning:
The example configuration below was created from a factory default configuration on the DGS-3324SR/DGS-3324SRi/DXS-
3350SR/DXS-3326GSR switches. We recommend saving your current configuration if necessary.

Net1 Net2 Net3


192.168.1.x 192.168.2.x 192.168.3.x
Gw192.168.1.253 Gw192.168.2.254 Gw192.168.3.254

DGS-3324SR_1

DGS-3324SR_2

Net1 Net4 Net5


192.168.1.x 192.168.4.x 192.168.5.x
Gw192.168.1.254 Gw192.168.4.254 Gw192.168.5.254

Scenario:
This configuration example shows a Layer 3 configuration on two DGS-3324SR switches. It can also apply to the DGS-3324SRi,
DXS-3350SR, and DXS-3326GSR switches as well. Each switch has different subnets. Now, in order to allow the subnets on the
switches to communicate with each other, Static Routes need to be configured in both devices so that:
1) Networks at DGS-3324SR_1 (ie, Net2, Net3) can ping Networks at DGS-3324SR_2 (Net4, Net5)
2) Networks at DGS-3324SR_2 (ie, Net4, Net5) can ping Networks at DGS-3324SR_1 (Net2, Net3)

The principle is that the packets with the destination to the “remote network” will be based on the static route entries in the switch
to route the packet to the “remote Switch”, and then to the “remote network.” This configuration example is based on firmware
version 4.10b15.

Switch CLI Configuration:

Step 1 Connect to the DGS-3324SR_1 switch using the console connection with your preferred Terminal emulation software.

Step 2 Once connected to the CLI, login at the username and password prompt (The default is username is <blank> and password
is <blank>).

Step 3 At the prompt, enter the following command:

reset system

Enter ‘y’ when prompted to confirm the factory reset. The switch will now reboot with the factory default settings.

Step 4 Login to the switch again.

Step 5 In the DGS-3324SR_1 switch CLI, enter the following commands to create the switch VLANs and related IP interfaces for
Net1, Net2 and Net3 on the DGS-3324SR_1 switch.

config vlan default delete 1:1-1:24


create vlan v101 tag 101
config vlan v101 add untagged 1:1-1:8
create ipif net1 192.168.1.253/24 v101 state enabled

create vlan v102 tag 102


config vlan v102 add untagged 1:9-1:16
create ipif net2 192.168.2.254/24 v102 state enabled

create vlan v103 tag 103


config vlan v103 add untagged 1:17-1:24
create ipif net3 192.168.3.254/24 v103 state enabled
save
How do I setup a Layer 3 network with Static Routes on my DGS-3324SR/DGS-3324SRi/DXS-3350SR/DXS-3326GSR? Page 2

Step 6 Enter the following commands on the DGS-3324SR_1 switch to add the Static Route entries for the 192.168.4.0/24 and
192.168.5.0/24 subnets.

create iproute 192.168.4.0/24 192.168.1.254


create iproute 192.168.5.0/24 192.168.1.254
save

Step 7 Repeat Step 1 to Step 4 for the DGS-3324SR_2 switch.

Step 8 Once logged into the DGS-3324SR_2 switch CLI, enter the following commands to create the switch VLANs and related IP
interfaces for Net1, Net4 and Net5 on the DGS-3324SR_2 switch.

config vlan default delete 1:1-1:24


create vlan v101 tag 101
config vlan v101 add untagged 1:1-1:8
create ipif net1 192.168.1.254/24 v101 state enabled

create vlan v104 tag 104


config vlan v104 add untagged 1:9-1:16
create ipif net4 192.168.4.254/24 v104 state enabled

create vlan v105 tag 105


config vlan v105 add untagged 1:17-1:24
create ipif net5 192.168.5.254/24 v105 state enabled
save

Step 9 Enter the following commands on the DGS-3324SR_2 switch to add the Static Route entries for the 192.168.2.0/24 and
192.168.3.0/24 subnets.

create iproute 192.168.2.0/24 192.168.1.253


create iproute 192.168.3.0/24 192.168.1.253

show iproute
save

Testing the Configuration:

1. Perform a ping test from a Net2 PC to a Net5 PC at the remote switch.


2. Perform a ping test from a Net3 PC to a Net4 PC at the remote switch.

Verify Configuration:

Below is a list of commands that can be used to verify the configuration and are useful for diagnostics:

show iproute

Below are the screen outputs for the above commands in this example. For more related CLI commands please refer to the CLI
reference manual for your switch model.

DGS-3324SR:4#show iproute
Command: show iproute

Routing Table

IP Address/Netmask Gateway Interface Cost Protocol


------------------ --------------- ------------ -------- --------
192.168.1.0/24 0.0.0.0 net1 1 Local
192.168.2.0/24 0.0.0.0 net2 1 Local
192.168.4.0/24 192.168.1.254 net1 1 Static
192.168.5.0/24 192.168.1.254 net1 1 Static

Total Entries : 4

You might also like