M

SERIES
Specifications
Walkie Stacker
C M Series Specifications

Model 20M Model 20MT

Fork Over Straddle

100˚ 100˚

5" (127 mm) 3" (76 mm)

25"
11
10 (635 12
6.7" (170 mm) mm)

55.5" 59"
(1410 mm) (1498 mm)

36" (915 mm)

1.5" (38 mm)

36" (915 mm)
9 13

9 13

6
3.0" 7
(76 mm) 8
6
7

2.1" 2" (51 mm)

(53 mm) 2"
4.5" 4"
2" (114 mm) (51 mm) (102 mm)
(51 mm)
14%
13%

ø 8.5 x 4" 1.9" (48 mm)

41.8" (1060 mm)
ø 8.5 x 4"
ø 4 x 2" ø 5 x 1.9" 62.3" (1582 mm) ø 4 x 2"
ø 5 x 1.9" 39.8" (1010 mm)
(102 x 51 mm) (216 x 102 mm) (102 x 51 mm)
(216 x 102 mm)
(127 x 48 mm)
(127 x 48 mm)
 M Series Specifications

Imperial Metric Imperial Metric

1 Manufacturer Crown Equipment Corporation
2 Model 20M 20MT
3 Load Capacity* lb kg 2000 907 2000 907
4 Load Center in mm 24 610 24 610
5 Mast Type Single Telescopic
6 Lifting Height in mm 67 1700 90 / 110 / 130 2285 / 2795 / 3300
Free Lift** (20MT) in mm 50 / 60 / 70 1270 / 1525 / 1780
7 Collapsed Height in mm 78 1980 71.5 / 81.5 / 91.5 1815 / 2070 / 2325
8 Extended Height*** (20MT) in mm 106.5 / 126.5 / 146.5 2705 / 3215 / 3720
9 Head Length in mm 31.5 800 34.2 / 34.2 / 34.2 870 / 870 / 870
Net Weight w/Batteries**** lb kg 990 450 1300 / 1400 / 1455 590 / 635 / 660
10 Overall Baseplate Width (20M) in mm 26 660
11 Inside/Outside Fork Spread (20M) in mm 15.8/25.9 400/660
12 Inside Straddle (20MT) in mm Adjustable in 2" Adjustable in 51 mm
increments from increments from
32" to 50" 815 to 1270 mm
Outside Straddle (20MT) in mm Inside plus 6.25" Inside plus 160 mm
13 Fork Lengths in mm 30, 36, 42, 48 760, 915, 1070, 1220 30, 36, 42, 48 760, 915, 1070, 1220
Overall Length (20M) in mm Head Length (9) plus Fork Length (13)
14 Fork Adjustment (20MT) 6.7 to 25 170 to 635
15 Travel Speed mph khr Three forward and Three forward and Three forward and Three forward and
reverse speeds to reverse speeds to reverse speeds to reverse speeds to
3 mph 5 khr 3 mph 5 khr
16 Lift Speed E/L fpm mps 25 / 13 .13 / .07 25 / 13 .13 / .07
17 Lowering Speed E/L fpm mps 14 / 22 .07 / .11 22 / 36 .11 / .18

*Attachments and longer load dimensions may result in derating of the capacity. Contact local dealer.
**Without load backrest (subtract 19.5" [495 mm] if optional load backrest is used.)
***Add 19.5" (495 mm) if optional load backrest is used.
****For the 20 MT model, add 90 lb (40.8 kg) for semi-industrial batteries.

M Series Aisle Planning Guide

Straddling Load
Pallet Length in (mm)
Pallet 30 (760) 36 (915) 42 (1070) 48 (1220)
Width A B A B A B A B
30 in 55 64 59 64 62 66 65 71
760 mm 1400 1625 1500 1625 1575 1675 1650 1805
36 in 59 65 62 66 65 69 68 72
915 mm 1500 1050 1575 1675 1650 1755 1730 1830
42 in 64 68 66 69 69 71 71 74
1070 mm 1625 1730 1675 1755 1755 1805 1805 1880
Pallet 48 in 69 72 70 72 72 74 74 77
Length 1220 mm 1755 1830 1780 1830 1830 1880 1880 1955
Pallet
Width
Load Over Outriggers
Pallet Length in (mm)
es

Pallet 30 (760) 36 (915) 42 (1070) 48 (1220)

sl
Ai

Width
g

A B A B A B A B
in
A
ct
se

30 in 50 63 54 64 57 66 60 68
er

B
nt

760 mm 1270 1600 1370 1625 1450 1675 1525 1730

lI

Right Angle Aisles

ua

36 in 53 64 57 65 60 67 63 69
Eq

915 mm 1345 1625 1450 1650 1525 1700 1600 1755

42 in 58 65 62 67 64 68 67 70
1070 mm 1475 1650 1575 1700 1625 1730 1700 1780
48 in 64 66 67 68 68 70 70 72
1220 mm 1625 1675 1700 1730 1730 1780 1780 1830

Add 6" (152 mm) to all aisle dimensions for maximum maneuverability.
 M Series Technical Information

Capacity Control Handle Safety Switches Mast Guard

Models 20M and 20MT Control handle with dual twist Third speed cutout switch may Clear, high impact acrylic to help
2000 lb (907 kg) at 24" grips which control three speeds be used to shut off high speed protect operator from chains
(610 mm) load center forward and reverse. Twist grips when operating in congested and cylinder.
return to neutral when released. areas. Third speed cutoff switch
Batteries (1) The handle provides 200° on telescopic models shuts off Lift Chain
Four six-volt three-cell, 17 plate steering and contains a large high speed when inner mast Two alloy steel leaf-type chains
(per cell) lead acid batteries - safety button which reverses the extends above “free lift” of forks.
each rated at 100 amp hours at Finish
direction of the truck should the Safety interlock switch cuts off Beige and dark gray
20 hour rate, or 87 amp hours at button touch the operator. A drive wheel power when service
six hour rate. large horn button is standard door is opened for charging and Dimensions and performance
Charger (1) equipment, as is a third speed maintenance. data given may vary due to
Built-in 120-volt 10 amp silicon cutoff switch. manufacturing tolerances.
Drive Unit Performance is based on an
rectifier type. Automatically Steering Spur gear drive direct from motor
tapers to trickle charge. Other average size vehicle and is
Steering column is mounted on to drive axle. Gear train is affected by weight, condition of
charger’s and voltages available. thrust and radial bearings for mounted on ball and tapered truck, how it is equipped and the
effortless steering. Steering roller bearings operating in oil
Semi-industrial battery and
(1)
handle can be turned 100° in conditions of the operating
bench type charger required for inside sealed gear housing. area. Crown products and speci-
either direction. Handle is spring Housing is equipped with mag-
Canada. loaded to return to vertical fications are subject to change
netic drain plug. Drive unit floats without notice.
Standard Equipment “brake-on” position when 2.5" (64 mm) to insure traction
1. 24-volt system released by operator. over uneven floors and on
2. Crown manufactured heavy- Wheels and Tires ramps. Heavy coil spring exerts
duty con­­tactors Steel caster wheels - 5" dia, 400 lb (180 kg) pressure on drive
1.9" face (127 mm dia, 48 mm wheel for maximum traction.
3. Third speed cutout switch face). Steel load wheels - 4" dia,
4. Series wound high-torque 2" face (102 mm dia, 51 mm Outriggers
drive and lift motor face) as standard. All wheels Heavy steel construction with
equipped with roller bearings. end contoured around load
5. Fused control and drive wheel. Each load wheel axle
circuits Drive tire - 8.5" x 4" x 4" (216
x 102 x 102 mm) standard is rounded to prevent pallet
6. Power disconnect pressed-on type rubber. damage.
7. Key switch Hydraulic System Carriage Rollers
8. Plexiglass mast guard Heavy-duty motor with gear Alloy steel rollers contoured
pump, check valve, relief valve to fit mast and equipped with
9. Raise/lower buttons in and control valve. Flow control roller bearings. Telescopic units
control handle valve regulates lowering speed have adjustable side-thrust
of forks. Lift cylinder with poly- mast rollers.
10. Adjustable outriggers urethane packings. Oil reservoir
(MT only) with breather-filter to prevent
foreign matter from entering
Optional Equipment hydraulic system. In-line suction
1. Load backrest filter to remove foreign matter
2. Polyurethane load, drive and from hydraulic circuit. Overload
caster wheels valve set to bypass oil to
reservoir when system reaches
3. Discharge meter
maximum pressure.
4. Hour meter
5. Semi-industrial battery and
40 amp bench type char-
ger complete with timer
(Required for Canada)
6. Maintenance platform
7. Remote raise/lower control
8. Snap-on platform
9. Wire mesh mast guard Crown Equipment Corporation
New Bremen, Ohio 45869 USA
Tel 419-629-2311
Fax 419-629-3796
crown.com

­You can count on Crown to build lift trucks Because Crown is continually improving its products,
specifications are subject to change without notice.
designed for safe operation, but that’s

only part of the safety equation. Crown Crown, the Crown logo, the color beige and the
Momentum symbol are trademarks of
encourages safe operating practices through Crown Equipment Corporation.

ongoing operator training, safety-focused Copyright 2002-2017 Crown Equipment Corporation

SF14109 Rev. 04-17
supervision, maintenance and a safe work-
Printed in U.S.A.
ing environment. Go to crown.com and view

our safety section to learn more.