UH320 Classic

Specification Summary
Sandvik UH320
General information
• UH320 Classic type; is superior in its function and can produce 3 calibrated fractions. The Unit can also
be used as a screen Unit, producing up to 4 products
• Well known Sandvik CH430 crusher with a wide range of mantels and settings for different applications
are available.
• ASRi is optional.
• Beneath the feeder and the screen the chute have 3 flaps which make it possible to divide the
feedmaterials so that 33%, 66% or 100% can ether be transported to the crusher or to the screen by
seperate conveyors. This make it possible to optimize the quality, and capacity with different raw
materials.
• Remote-controlled tiltable static bar grizzly on feed hopper. Adjustable fixed position between 7-17°.
The grizzly is divided in three sections, which can easily be taken off when the feeder is loaded from a
conveyor and also changed according to individual wear. The whole grizzly can be removed if not
required. Grizzly separation is accordingly to the crusher chamber 100mm alt. 125mm.
• Foldable flaps on feed hopper can give wider loading area.
• IR level monitors on feed hopper to regulate the feed rate.
• A foldable flap on each side can be used as a back-wall for a loading ramp and as protection against
oversize stones falling from the tip able grizzly.
• The Screen is a SF1843 which can take out 3 calibrated fractions
• Rollaway discharge chute on screen provides easy access for inspection and service.
• Flaps inside the chute provide adding top fractions with fine fractions except for the oversize conveyor
• All conveyors are electrically driven and hydraulically foldable for transport, except for the oversize
return conveyor.
• Oversize conveyor is equipped with stone brake and side protection plates intended only for screening
natural gravel (to prevent rolling stones causing damage and accidents). Removed during transport.
•
SANDVIK UH320
Dust-encapsulated feed conveyor, screen and conveyor for the finest fraction.
• Hydraulic supporting legs at front end make connection with semi-trailer easier.
• The whole unit can be transported in one piece if local transport legislation permits, start-up time
approx. 30 minutes.
• Walkways (with stepladders) around the screen, to provide easy access for inspection and service.
• Self-contained galvanised steel switchgear cabinet fixed on-board the unit. The cabinet contains all the
components necessary for power distribution and control - fuses, contactors, indicating lamps, control
push buttons, interlocking relays, etc.
• Emergency stop push buttons are placed at strategic locations.
• Frequency convertor for feeder and conveyor for coarsest product, to provide step less regulation of
feed rate and conveyor speed.
• 220V transformer for power outlet ( 2pc.10A, 1pc.16A).
• 32-pole connection for external control of the Unit.
• The Unit has no on-board genset due to the axle load limits.
• The design and manufacture of UH320 complies with ISO 9001
08-02
Specification Summary
Dimension
Operation
Height 5.20m
Width 3.00m
Length 22.00
Transport
Height 4.50m
Width 3.00m
Length 17.85m
Weight1
tons 48,50ton
short tons
1 excluding options
Feed station
SP 0830 2 x 2,3 kW electric motor 5kbm
Crusher
Type Sandvik CH430

Feed opening 100 mm (TS)
Drive 132 kW electric motor
Conveyors Length Width Motor Speed
Feed con belt: 10.6 m 800mm 1.3m/s (to the

screen)
Rear con: 9.5 m 800mm 1.25m/s
3 pro con: 8m 650mm 1.0m/s
Optional extra equipment NF-conv. 8m 500 mm
RC2. Ball-deck beneath the third deck in the

SF1843
Screen
RC3. Electrical heating system for feeder bottom
and feed hopper. Product screen SF1843
RC4. Electric heaters under the feed conveyor Motor 2 x 11 kW electric motors
and the conveyor for the finest fraction.
RC5. Dust collector. Hydraulic system
RC6. Floodlights on illumination mast. Coarse stone grizzly: Hydraulic power pack,
RC9. Control voltage 110 V 400V, 4kW
SANDVIK UH320
Foldable conveyors, supporting legs, retractable

RC10. Start siren screen:
RC7. NF screen Hydraulic power pack, 24V (alt.400V), 3kW (alt.
4kW)
RC11. Overband magnet for conveyor 4.
RC12. ASRi. Requiered power
RC 13 Metaldetector on return conveyor 5. Generator 325 kVA 400V
RC18. Synthetic oil
Running gear
RC19 Heating for the crusher oil incl. 6kVA
genset. Type: King-pin 3 ½” or 2 ”. Leaf-sprung two-axle
RC19A. Diesel heating for the crusher oil. bogie, air- brakes and running lights. 4 Tires
385/65R/22.5.
08-02

UH320 Classic

Uploaded by

Copyright:

Available Formats

UH320 Classic

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

UH320 Classic

Uploaded by

Copyright:

Available Formats

Specification Summary

SP 0830 2 x 2,3 kW electric motor 5kbm

Type Sandvik CH430

Conveyors Length Width Motor Speed

Feed con belt: 10.6 m 800mm 1.3m/s (to the

RC2. Ball-deck beneath the third deck in the

Foldable conveyors, supporting legs, retractable

You might also like