Scribd
Upload
450 views

Elevator Control Wiring and Simple Configuration: Button Mode

1) The document provides instructions for wiring an elevator control system and configuring it for button access control using an access control device. 2) It involves setting DIP switches, wiring relays to buttons, adding the device to the access control software, configuring floor-to-relay mappings, setting delay times, adding user permissions, and validating card access. 3) The configuration process involves 12 steps in the access control software to activate the device, add it to the client, set permissions for a card, and validate that the proper relays activate for the authorized floors when that card is swiped.

Uploaded by

Agnelo Fernandes
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
450 views

Elevator Control Wiring and Simple Configuration: Button Mode

1) The document provides instructions for wiring an elevator control system and configuring it for button access control using an access control device. 2) It involves setting DIP switches, wiring relays to buttons, adding the device to the access control software, configuring floor-to-relay mappings, setting delay times, adding user permissions, and validating card access. 3) The configuration process involves 12 steps in the access control software to activate the device, add it to the client, set permissions for a card, and validate that the proper relays activate for the authorized floors when that card is swiped.

Uploaded by

Agnelo Fernandes
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 7

Elevator control wiring and simple

Title: Version: v1.0 Date: 5/12/2017


configuration （Button mode）
Product: Access Control Device Page: 1 of 7

Elevator control wiring and simple configuration


（Button mode）
Preparation：
Prepare the following equipment for the test, complete the test and then install
DS-k2210 DS-k2m0016 DS-k1106

Step 1: DIP Switch


The DIP switch of the card reader should be decimal 1 or 2.
The DIP switch of Ds-2100 should be decimal 1or 2.
The DIP switch of distributed elevator controller (DS-K2M0016A) is decimal 3-10

The device uses binary dialing codes


If you want to get dialing 3, Dial 1 and 2,if you want to get 4, Dial 3

Step2:Wring
Elevator control wiring and simple
Title: Version: v1.0 Date: 5/12/2017
configuration （Button mode）
Product: Access Control Device Page: 2 of 7

Step 3:Installation
Installation of elevator controller and Elevator button connection
controller installation diagram

Principle:

Button（The DIP switch of distributed elevator controller (DS-K2M0016A) is decimal 3-10） ：We
control the buttons in the elevator, just put the NC and COM into the button circuit, if the
permission is verifiable，the relay will action and you can press the corresponding button. This part
we need use NC and COM, because the NC and COM is disconnected when the controller with
power supply，and it will be the opposite without power supply in button mode. The advantage
of this mechanism is the controller will release control without power supply，which can avoid
hidden dangers.

Connect the relay string to the corresponding button


Elevator control wiring and simple
Title: Version: v1.0 Date: 5/12/2017
configuration （Button mode）
Product: Access Control Device Page: 3 of 7

Step 3:Configuration
1.4200(2.6.2.7) ConfigurationClick the access control

2.Activate device

3.Modify net info

4.Add to client
User name：admin
Elevator control wiring and simple
Title: Version: v1.0 Date: 5/12/2017
configuration （Button mode）
Product: Access Control Device Page: 4 of 7

To activate the password, you must check “Export to Group”

5.Determine the controller to display online

6.Configuring the correspondence between floor and relay

Note:Drag the right relay to the corresponding floor


Click on the upper right corner after the configuration is completed.
The first number of the right relay is based on the Numerical Value of the dip switch

7.Set the delay time for each floor by default to 120s, which can be set to 15s
Elevator control wiring and simple
Title: Version: v1.0 Date: 5/12/2017
configuration （Button mode）
Product: Access Control Device Page: 5 of 7

8.add the staff permission

9.Add a person's card

10.Add permissions, check permissions and click on the right direction to click ok

11.When you click ok, you will be prompted to send it, and you can click directly.
Elevator control wiring and simple
Title: Version: v1.0 Date: 5/12/2017
configuration （Button mode）
Product: Access Control Device Page: 6 of 7

12.Can also be selected permissions set after clicking all issued (delete permission first,
then issued all permissions, generally after adding new equipment use) or move issued
(group permission to use when there is new change).

Step4 :Validate

I give this card the permission of the first three floors，after swiping card，We can see
the corresponding relay acted by these pictures。
Elevator control wiring and simple
Title: Version: v1.0 Date: 5/12/2017
configuration （Button mode）
Product: Access Control Device Page: 7 of 7

First Choice for Security Professionals


HIKVISION Technical Support

You might also like