Tutorial For Force Spectrum Analysis Using CAEPIPE: General

This document provides a 7-step tutorial for performing force spectrum analysis using CAEPIPE software. Force spectrum analysis determines piping system response to impulsive loads by applying time-history load data from fluid transient analysis as force spectra - tables of maximum dynamic force versus frequency. The tutorial demonstrates how to input force spectrum tables into CAEPIPE models, apply the loads to nodes, analyze the model with force spectrum loads, and review results.

Uploaded by

FRANCISCO

Available Formats

Download as PDF, TXT or read online on Scribd

0% found this document useful (0 votes)

69 views

Tutorial For Force Spectrum Analysis Using CAEPIPE: General

Uploaded by

FRANCISCO

Available Formats

Download as PDF, TXT or read online on Scribd

You are on page 1/ 7

Tutorial for Force Spectrum Analysis using CAEPIPE

The following are the Steps for performing the Force Spectrum Analysis using CAEPIPE.

General
Force spectrum analyses are generally performed to determine the response of the piping system to short-
duration impulsive loads such as fluid hammer, safety relief valve (SRV) and slug flow loads. For an actual short-
duration impulsive dynamic load exerted on a piping system, a fluid transient analysis is first carried out in order
to arrive at the “time-history loads” (i.e., force vs. time) acting in the three global directions (namely global X, Y
and Z) at all affected points in the piping system. The time-history load sets so computed are then applied, one
time-history load set at a time, on a single degree-of-freedom (dof) spring-mass system with a pre-set natural
frequency, to determine the maximum dynamic response of this single dof system with that natural frequency.
Such dynamic analysis for that time-history load is repeated on the same single dof system with different pre-set
natural frequencies. The force spectrum for that time-history load would then be a table of maximum dynamic
response computed for the single dof system with different natural frequencies. In other words, the force
spectrum is a table of force spectral values vs frequencies that captures the maximum intensity and frequency
content of that time-history load. Similarly, force spectrum tables are determined for all other time-history load
sets. The above force spectrum tables (i.e., maximum dynamic force vs frequency) are then applied as inputs at
the respective piping nodes of the CAEPIPE stress model to compute displacements, forces and stresses.
For any piping system, there are as many natural modes of vibrations as the number of dynamic degrees of
freedom for that system. The force spectral value corresponding to a natural frequency of the piping system is
arrived at by interpolating the force spectrum vs frequency table as determined above. For better
understanding, as an example, refer to the graph shown next as well as the natural frequencies computed for a
piping system at 10 Hz, 14 Hz, 21 Hz, 29 Hz and 33.8 Hz.

From the above graph, to arrive at a force value corresponding to a natural frequency of 14 Hz, CAEPIPE
interpolates the force spectral values between 13 and 15 Hz. Similarly, to arrive at a force value corresponding
to a natural frequency of 21 Hz, CAEPIPE interpolates the force spectral values between 20 Hz & 25 Hz. Since
force spectral values above 25 Hz are not defined in the graph shown above, CAEPIPE arrives at a force value of
1650 lb. (i.e., the spectral value corresponding to the maximum frequency of 25 Hz in the above plot) even for
natural frequencies of 29 and 33.8 Hz. Similarly, CAEPIPE arrives at a force value of 900 lb. for a natural
frequency of 10 Hz (i.e., the spectral value corresponding to the minimum frequency of 13 Hz in the above plot).
The results of the modal analysis are used with force spectrum loads to calculate the response (displacements,
support loads and stresses) of the piping system. It is often used in place of a time-history analysis to determine
the response of the piping system to sudden impulsive loads such as water hammer, relief valve and slug flow.
The force spectrum is a table of force spectral values versus frequencies that captures the intensity and
frequency content of the time-history loads. It is a table of Dynamic Load Factors (DLF) versus natural
frequencies. DLF is the ratio of the maximum dynamic displacement divided by the maximum static
displacement. Note that Force spectrum is a non-dimensional function (since it is a ratio) defining a curve
representing force versus frequency. The actual force spectrum load at a node is defined using this force
spectrum in addition to the direction (FX, FY, FZ, MX, MY, MZ), units (lb, N, kg, ft-lb, in-lb, Nm, kg-m) and a scale
factor.

Tutorial
Step 1:
Attached is a sample CAEPIPE model with Force Spectrum. The steps followed in generating the model are
shown in the snap shot below.
Step 2:
After creating your piping model (with node 75 being the center node of the discharge bend where the Force
Spectrum will be applied), input Force spectrums through Layout or List menu: Misc > Force spectrums.
Step 3:
The Force spectrum list appears.
Enter a name for the force spectrum and spectrum values versus frequencies table.

In addition to inputting the force spectrum directly, it can also be read from a text file. This can be done through
List menu: File > Read force spectrum.

The text file should be in the following format:

Name (up to 31 characters)
Frequency (Hz) Spectrum value
Frequency (Hz) Spectrum value
Frequency (Hz) Spectrum value
. .
. .
The frequencies can be in any order. They will be sorted in ascending order after reading from the file.
Step 4:
Apply the Force Spectrum Load thus generated at the bend center node 75 after the relief valve in vertical
direction (FY) as shown below.

Step 5:
Check “Force Spectrum” for analysis through Layout window > Load cases. Click on OK.
Step 6:
Save and Analyze the model. After analysis, CAEPIPE displays Occasional stresses which include the effects of
the Force Spectrum load.

Step 7:
Another load case called “Force Spectrum” will be available for which you can study displacements, support
loads, support load summary (for sizing supports), etc.