1

Mechanical Properties
Components Specifications Yield, Re min. [Mpa] Tensile, Rm min. [Mpa]
Channel Profiles
Carbon Steel S235JR, EN 10025 235 360
SS 304 [A2] W 1.4301, EN 10088 195 500
SS 316 [A4] W 1.4401/1.4571, EN 10088 240 530
Anchors
Carbon Steel S235 (ST-37.2), EN10025 235 360
AISI 1010 250 365
SS 316 [A4] W 1.4401/1.4571, EN 10088 240 530
Tee Bolts
Strength 4.6 Grade 4.6, EN ISO 898-1 240 400
Strength 8.8 Grade 8.8, EN ISO 898-1 640 800
A4-50 A4-50, EN ISO 3506-1 210 500
A4-70 A4-70, EN ISO 3506-1 450 700
Channel Nuts
Carbon Steel S235JR (ST 37-2), EN 10025 235 360
*C 1015, SAE 355 500
SS 316 [A4] W 1.4401/1.4571, EN 10088 240 530

Europe China Japan Germany U.K. U.S.A

EN GB JIS DIN BS ASTM

S235JR 1.0037 Q235 SS400 ST 37-2 37/23 Gr 33

S235JR 1.0038 Q235B SN400 RST 37-2 40B A 36

S275 1.0044 Q275 - RST 44-2 43C Gr 42

A2 1.4301 304 SUS304 1.4301 304S15 304

A4 1.4401 316 SUS316 1.4401 316S31 316

A4 1.4571 316Ti SUS316Ti 1.4571 320S31 316Ti

 Process Standard Coating Thickness
Hot Dip Galvanizing EN ISO 1461 ≥ 50 µm

Electro Zinc Plating EN 12329 ≥ 5 µm

Degrease + Descale Mill Finish 1D

Clear Passivated (A4 Fasteners only)

Load Cycles 104 x
N 1 2 3 4 5 6 7 8 9
Reduction
1.00 0.82 0.70 0.64 0.58 0.54 0.52 0.49 0.47
Factor, K

Load Cycles 105 x

N 1 2 3 4 5 6 7 8 9
Reduction
0.46 0.38 0.37 0.35 0.33 0.32 0.31 0.30 0.29
Factor, K

Load Cycles 106 x

N 1 2 3
Reduction
0.29 0.28 0.28
Factor, K
 Sampag Tee Bolts European Channel Profiles

TS 38 38/17

TS 40 40/22, 40/25, 41/25

TS 50 49/30, 50/30, 51/31, 52/34, 53/35

THREAD
Diameter 4.6 8.8 A4-50 A4-70
Ø [Nm] [Nm] [Nm] [Nm]

M8 5.0 - - -

M10 10.0 24.9 8.7 18.7

M12 17.5 43.7 15.3 32.3

M16 44.4 111.0 38.8 83.3

M20 86.5 216.4 75.7 162.3

M24 149.7 350.1 130.9 -

 Grade 4.6 Grade 8.8
Diameter Stress Area, As Tension, FZ Shear, FY Torque Tension, FZ Shear, FY Torque
Ø [mm²] [kN] [kN] [Nm] [kN] [kN] [Nm]
M8 36.6 4.9 3.3 8.0 9.8 6.3 24.0
M10 58.0 7.8 5.3 15.0 15.5 10.6 48.0
M12 84.3 11.3 7.5 25.0 22.5 15.7 70.0
M16 157.0 21.0 14.2 60.0 42.0 28.2 200.0
M20 245.0 32.7 21.0 120.0 65.3 45.0 400.0
M24 353.0 47.1 31.6 200.0 94.2 63.0 680.0

A4-50 A4-70
Diameter Stress Area, As Tension, FZ Shear, FY Torque Tension, FZ Shear, FY Torque
Ø [mm²] [kN] [kN] [Nm] [kN] [kN] [Nm]
M8 36.6 5.1 3.6 8.0 - - -
M10 58.0 8.0 5.7 15.0 14.1 9.3 15.0
M12 84.3 11.3 8.1 25.0 20.6 13.6 25.0
M16 157.0 21.2 15.3 60.0 37.2 24.5 60.0
M20 245.0 32.3 22.5 120.0 58.3 38.4 120.0
M24 353.0 47.4 33.8 200.0 84.2 56.1 200.0
 Edge Distance, aᵣ Load Reduction Factors
[mm] Tension Shear
≥ 90 1.00 1.00
75 1.00 0.78
65 0.93 0.66
55 0.86 0.55

LOAD CONFIGURATION ALLOWABLE LOADS

“F” Applicable Channel Spacing TENSION SHEAR
As Length, L Distance Point FZ Pair F’Z Point FY Pair F’Y
Tension or Shear [mm] [mm] [kN] [kN] [kN] [kN]

1050 a = 200

to b ≥ 200 6.5 8.0 8.6 10.0

6070 c ≥ 100

100 - 8.5 - 9.0 -

150 c ≥ 50 8.5 10.4 9.0 10.4

200 c ≥ 75 8.5 10.4 9.0 10.4

250 c ≥ 100 - 15.0 - 15.0

300 c ≥ 125 - 15.0 - 15.0

350 c ≥ 125 - 14.6 - 14.6

Channel Weight Sectional Moment of Inertia Section Modulus
Profile (w/o anchors) Area Y-Y Z-Z Y-Y Z-Z
TS 38/17 1.73 kg/m 2.19 cm2 0.74 cm4 3.39 cm4 0.74 cm3 2.07 cm3

Thread Allowable Loads in [kN] Tightening Torque

Diameter 4.6 A4-50 4.6 + A4-50
Ø Tension Shear Tension Shear [Nm]
M10 7.8 5.3 8.0 5.7 15
M12 11.8 7.5 11.3 8.1 25
M16 21.0 14.2 21.2 15.3 60
 Edge Distance, aᵣ Load Reduction Factors
[mm] Tension Shear
≥ 100 1.00 1.00
85 1.00 0.80
75 0.97 0.62
60 0.88 0.44

LOAD CONFIGURATION ALLOWABLE LOADS

“F” Applicable Channel Spacing TENSION SHEAR
As Length, L Distance Point FZ Pair F’Z Point FY Pair F’Y
Tension or Shear [mm] [mm] [kN] [kN] [kN] [kN]

1050 a = 200

to b ≥ 200 8.0 9.6 10.0 12.0

6070 c ≥ 100

100 - 10.0 - 10.0 -

150 c ≥ 50 10.0 12.0 10.0 12.4

200 c ≥ 75 10.0 12.0 10.0 12.4

250 c ≥ 100 - 17.2 - 18.0

300 c ≥ 125 - 17.2 - 18.0

350 c ≥ 125 - 17.2 - 18.0

Channel Weight Sectional Moment of Inertia Section Modulus
Profile (w/o anchors) Area Y-Y Z-Z Y-Y Z-Z
TS 40/22 2.13 kg/m 2.71 cm2 1.83 cm4 5.97 cm4 1.55 cm3 2.99 cm3

Thread
Diameter 4.6 8.8 A4-50
Ø Tension Shear Tension Shear Tension Shear [Nm] [Nm] [Nm]
M10 7.8 5.3 15.5 10.6 8.0 5.7 15 48 15
M12 11.3 7.5 22.5 15.7 11.3 8.1 25 70 25
M16 21.0 14.2 42.0 28.2 21.2 15.3 60 200 60
 Edge Distance, aᵣ Load Reduction Factors
[mm] Tension Shear
≥ 105 1.00 1.00
90 1.00 0.80
75 0.97 0.62
60 0.88 0.44
50 0.62 0.21

LOAD CONFIGURATION ALLOWABLE LOADS

“F” Applicable Channel Spacing TENSION SHEAR
As Length, L Distance Point FZ Pair F’Z Point FY Pair F’Y
Tension or Shear [mm] [mm] [kN] [kN] [kN] [kN]

1050 a = 200

to b ≥ 200 8.8 11.0 12.0 14.0

6070 c ≥ 100

100 - 11.0 - 11.0 -

150 c ≥ 50 10.5 12.6 11.0 14.0

200 c ≥ 75 10.5 12.6 11.0 14.0

250 c ≥ 100 - 18.4 - 20.0

300 c ≥ 125 - 18.4 - 20.0

350 c ≥ 125 - 18.4 - 20.0

300x300 c ≥ 125 - 18.0 - 18.0

Channel Weight Sectional Moment of Inertia Section Modulus
Profile (w/o anchors) Area Y-Y Z-Z Y-Y Z-Z
TS 40/25 2.14 kg/m 2.88 cm2 2.26 cm4 6.62 cm4 1.52 cm3 3.27 cm3

Thread
Diameter 4.6 8.8 A4-50
Ø Tension Shear Tension Shear Tension Shear [Nm] [Nm] [Nm]
M10 7.8 5.3 15.5 10.6 8.0 5.7 15 48 15
M12 11.3 7.5 22.5 15.7 11.3 8.1 25 70 25
M16 21.0 14.2 42.0 28.2 21.2 15.3 60 200 60
 Edge Distance, aᵣ Load Reduction Factors
[mm] Tension Shear
≥ 115 1.00 1.00
100 0.99 0.78
85 0.96 0.60
70 0.88 0.42
60 0.68 0.24

LOAD CONFIGURATION ALLOWABLE LOADS

“F” Applicable Channel Spacing TENSION SHEAR
As Length, L Distance Point FZ Pair F’Z Point FY Pair F’Y
Tension or Shear [mm] [mm] [kN] [kN] [kN] [kN]

1050 a = 250

to b ≥ 250 12.0 14.8 12.0 16.8

6070 c ≥ 100

100 - 13.0 - 14.0 -

150 c ≥ 50 13.0 16.0 14.0 18.0

200 c ≥ 75 13.0 16.0 14.0 24.0

300 c ≥ 125 - 25.0 - 26.0

350 c ≥ 125 - 27.0 - 28.0

450 c ≥ 125 - 29.0 - 30.0

350x350 c ≥ 125 - 25.0 - 26.0

Channel Weight Sectional Moment of Inertia Section Modulus
Profile (w/o anchors) Area Y-Y Z-Z Y-Y Z-Z
TS 41/25 2.96 kg/m 3.77 cm2 3.02 cm4 8.83 cm4 2.33 cm3 4.32 cm3

Thread
Diameter 4.6 8.8 A4-50
Ø Tension Shear Tension Shear Tension Shear [Nm] [Nm] [Nm]
M10 7.8 5.3 15.5 10.6 8.0 5.7 15 48 15
M12 11.3 7.5 22.5 15.7 11.3 8.1 25 70 25
M16 21.0 14.2 42.0 28.2 21.2 15.3 60 200 60
 Edge Distance, aᵣ Load Reduction Factors
[mm] Tension Shear
≥ 125 1.00 1.00
110 1.00 0.78
95 0.96 0.61
80 0.88 0.36
65 0.72 0.21

LOAD CONFIGURATION ALLOWABLE LOADS

“F” Applicable Channel Spacing TENSION SHEAR
As Length, L Distance Point FZ Pair F’Z Point FY Pair F’Y
Tension or Shear [mm] [mm] [kN] [kN] [kN] [kN]

1050 a = 250

to b ≥ 250 10.0 12.0 11.0 13.0

6070 c ≥ 100

150 c ≥ 50 12.0 14.0 12.0 14.6

200 c ≥ 75 12.0 14.0 12.0 14.6

250 c ≥ 100 12.0 14.0 12.0 14.6

300 c ≥ 125 - 22.0 - 23.0

350 c ≥ 125 - 23.0 - 24.0

350x350 c ≥ 125 - 22.0 - 22.0

Channel Weight Sectional Moment of Inertia Section Modulus
Profile (w/o anchors) Area Y-Y Z-Z Y-Y Z-Z
TS 50/30 3.29 kg/m 4.2 cm2 5.42 cm4 14.68 cm4 3.55 cm3 5.87 cm3

Thread
Diameter 4.6 8.8 A4-70
Ø Tension Shear Tension Shear Tension Shear [Nm] [Nm] [Nm]
M12 11.8 7.5 23.8 15.7 20.6 13.6 25 70 25
M16 22.2 14.2 45.0 28.2 37.2 24.5 60 200 60
M20 33.8 21.0 68.2 45.0 58.3 38.4 120 400 120
 LOAD CONFIGURATION ALLOWABLE LOADS
“F” Applicable Channel Spacing TENSION SHEAR
As Length, L Distance Point FZ Pair F’Z Point FY Pair F’Y
Tension or Shear [mm] [mm] [kN] [kN] [kN] [kN]

1050 a = 250

to b ≥ 250 18.0 (20.0) 21.0 (23.0) 19.0 (19.0) 24.0 (32.0)

6070 c ≥ 100

150 c ≥ 50 18.0 (20.0) 20.0 (22.0) 17.0 (19.0) 22.0 (24.0)

200 c ≥ 75 18.0 (20.0) 21.0 (24.0) 17.0 (20.0) 24.0 (26.0)

250 c ≥ 100 18.0 (20.0) 22.0 (26.0) 17.0 (22.0) 24.0 (26.0)

300 c ≥ 125 - 30.0 - 42.0

350 c ≥ 125 - 36.0 (46.0) - 42.0 (46.0)

450 c ≥ 175 - 38.0 (48.0) - 44.0 (48.0)

350x350 c ≥ 125 - 34.0 (44.0) - 40.0 (44.0)

 Edge Distance, aᵣ Load Reduction Factors
[mm] Tension Shear
≥125 (185)* 1.00 (1.00)* 1.00 (1.00)*
110 (165) 0.99 (1.00) 0.80 (0.82)
95 (145) 0.96 (0.97) 0.62 (0.68)
80 (125) 0.88 (0.92) 0.36 (0.48)
65 (105) 0.72 (0.86) 0.21 (0.33)
50 (85) 0.56 (0.78) -

Channel Weight Sectional Moment of Inertia Section Modulus

Profile (w/o anchors) Area Y-Y Z-Z Y-Y Z-Z
TS 51/31 4.33 kg/m 5.39 cm2 6.94 cm4 18.90 cm4 4.38 cm3 7.49 cm3

Thread
Diameter 4.6 8.8 A4-70
Ø Tension Shear Tension Shear Tension Shear [Nm] [Nm] [Nm]
M12 11.3 7.5 22.5 15.7 20.6 13.6 25 70 25
M16 21.0 14.2 42.0 28.2 37.2 24.5 60 200 60
M20 32.7 21.0 65.3 45.0 58.3 38.4 120 400 120
 Edge Distance, aᵣ Load Reduction Factors
[mm] Tension Shear
≥ 215 1.00 1.00
195 1.00 0.76
170 0.98 0.58
140 0.95 0.42
110 0.86 0.31
95 0.78 -

LOAD CONFIGURATION ALLOWABLE LOADS

“F” Applicable Channel Spacing TENSION SHEAR
As Length, L Distance Point FZ Pair F’Z Point FY Pair F’Y
Tension or Shear [mm] [mm] [kN] [kN] [kN] [kN]

1050 a ≥ 250

to b ≥ 250 24.0 26.0 24.0 26.0

6070 c ≥ 100

200 c ≥ 75 27.0 33.0 27.0 33.0

250 c ≥ 100 27.0 34.0 27.0 36.0

300 c ≥ 125 27.0 38.0 27.0 42.0

350 c ≥ 125 - 54.0 - 54.0

450 c ≥ 175 - 57.0 - 56.0

350x350 c ≥ 125 - 53.0 - 53.0

Channel Weight Sectional Moment of Inertia Section Modulus
Profile (w/o anchors) Area Y-Y Z-Z Y-Y Z-Z
TS 53/35 5.00 kg/m 6.35 cm2 9.48 cm4 23.76 cm4 5.51 cm3 9.14 cm3

Thread
Diameter 4.6 8.8 A4-70
Ø Tension Shear Tension Shear Tension Shear [Nm] [Nm] [Nm]
M12 11.3 7.5 22.5 15.7 20.6 13.6 25 70 25
M16 21.0 14.2 42.0 28.2 37.2 24.5 60 200 60
M20 32.7 21.0 65.3 45.0 58.3 38.4 120 400 120