Unit-1(Lecture 1-8)

Equivalent weight of CaCO3 is

a. Half of its molecular weight b. Equal to molecular weight
c. double of its molecular weight d. None of these
2. The correct inter-relation among the following is
(a) 1ppm=1 oFr (b) 1ppm=0.1oFr (c) 1ppm= 7 oFr (d) None of these
3. Degree Clarke (°Cl) is the number of equivalent parts of CaCO3 present per
(a) 106 parts of water (b) 1 gallon of water (c) 105 parts of water (d) 5000 parts of water
2. Permanent hardness of water is caused by the presence of
(a) Bicarbonates of Ca and Mg (b) Chlorides and sulfates of Ca and Mg (c) Carbonates of Na and
K (d) All of these
3. Hardness in water is measured by the amount of
(a) Mg2+ and Ca2+ (b) Zn2+ and Fe2+ (c) Mg2+ and Fe2+ (d) Ca2+ and Zn2+
4. Which of the following is an correct match
(a) Temporary Hardness- Bicarbonates of Mg2+ and Ca2+ (b) Temporary Hardness- chlorides
and sulphates of Ca2+ and Mg2+ (c) Both (a) and (b) (d) None of these
5. Indicator used for determination of total hardness is
(a) Eriochrome black-T (b) Phenolphthalein (c) Methyl orange (d) Ferroin
6. EDTA method used to determine hardness of water by EDTA method endpoint is
(a) Yellow to orange (b) blue to wine (c) Wine red to blue (d) Colourless to pink
7. Complete alkalanity of water is determined by using indicator
(a) Phenolphthailene (b) Methyl orange (c) Methyl red (d) Phenol red
8. If P=M then alkalinity is due to ----------
(a) OH- (b) HCO3- (c) CO3 2- (d) OH- and CO32-
9. In alkalinity of water experiment phenolphthalein end point is
(a) Pink to colourless (b) Yellow to red (c) Clourless to pink (d) None of these
10. The decomposition of Ca(HCO3)2 leads to formation
(a) CaCO3 (b) CaO (c) Ca(OH)2 (d) CO
11. 10 mg/lit is equal to
(a) 0.1 ppm (b) 10 ppm (c) 1 ppm (d) 1000 ppm
12. Mg (HCO3)2 →
(a) MgCO3 + CO2 + H2O (b) MgCO3 + CO2 (c) Mg(OH)2 + 2CO2 (d) Mg(OH)2 + 2CO3
13. Which of the following doesn’t precipitate as scale?
(a) Ca(HCO3)2
(b) CaSO4
(c) CaCl2
(d) Mg(HCO3) 2
14. Priming is
(a) large drops of water into outlet steam.
(b) persistent bubble on boiler water surface.
(c) presence of chlorine in water.
(d) presence of alkalinity in water stream.
15. Boiler material become brittle due to exposure to
(a) Ca(OH)2
(b) NaOH
(c) MgCl2
(d) KOH
16. Which of the following is an internal method of treating water?
(a) Lime soda process
(b) Ion exchange process
(c) Calgon method
(d) Both a & b
17. Ion exchange process is also known as
(a) Mineralization
(b) Complexation
(c) Reverse osmosis
(d) Demineralization
18. Lime in soda-lime process is used to remove
(a) Permanent hardness
(b) Permanent softness
(c) Both permanent hardness and temperory hardness
(d) Temperory Hardness
19. Which of the following is Membrane-based processes for desalination of impure water
(a) Reverse osmosis
(b) Electrodialysis
(c) Both a & b
(d) Ion exchange method
20. Which chemical is mainly responsible for disinfection process of water?
(a) HCl
(b) Cl
(c) HOCl
(d) O2
21. Which of the following should not be a property of a chemical disinfectant?
(a) Should kill microorganism
(b) Expensive
(c) Non toxic to human
(d) Should provide protection against any contamination
Unit-2(Lecture 10-13)
Q.1: Which of the following is not a natural polymer?
a) natural rubber
b) cis-polyisoprene
c) trans-polyisoprene
d) trans-polyacetylene
Q.2: Which of the polymer undergo reversible changes on heating?
a) Bakelite
b) PVC
c) Both a & b
d) Phenol-Formaldehyde polymer
Q.3. Which of the following polymer is formed from condensation polymerization?
a) Nylon 6,6
b) Urea-Formaldehyde resin
c) Thermosetting plastic
d) All of these
Q.4. Phenol-Formaldehyde resin is the type of
a) Linear polymer
b) Branched polymer
c) Network polymer
d) Block polymer
Q.5. Functionality of monomer means
a) functions of monomer
b) functions of polyomer
c) number of repeating units
d) total number of bonding sites
Q.6. Which of the following molding technique is used for thermosetting polymers?
a) Injection molding
b) Extrusion molding
c) Both a& b
d) Compression molding
Q.7. Ebonite is
a) less vulcanized rubber
b) high vulcanized rubber
c) natural rubber
d) gutta-percha rubber
Q.8. Which of the following is a Step growth polymer?
a) Teflon
b) PVC
c) both a & b
d) Bakelite
Q.9. Choose the correct name for monomer of natural rubber
a) acetylene
b) methane
c) isoprene
d) ethylene
Q.10. For a macromolecule tacticity is the study of:
(a) Crystallinity
(b) Stereochemistry
(c) Molecular weight
(d) Degree of polymerization
11. vulcanized rubber has
(a) good tensile strength
(b) bad tensile strength
(c) conducting Property
(d) low durability
12. Conducting polymer is used in –
(a) display device
(b) light emitting diodes
(c) information storage device
(d) all of these
13. Polyacetylene is a
(a) non conductive polymer
(b) conducting polymer
(c) composite material
(d) none of these
14. Which type of polymer is used in light emitting diodes-
(a) conducting
(b) non conducting
(c) vulcanized rubber
(d) teflon
15. Nylon 6.6 is used in
(a) fishing lines
(b) sports equipment
(c) combs
(d) all of these
16. HDPE is a
(a) homo polymer
(b) copolymer
(c) conducting polymer
(d) none of these
17. Drinking straw is made by
(a) extrusion molding
(b) injection molding
(c) compression molding
(d) none
18. Compression molding is usually used for
(a) thermoplastic
(b) thermosetting
(c) both a and b
(d) none of these
19. Phenol-formaldehyde resin is a
(a) homopolymer
(b) copolymer
(c) both homo and copolymer
(d) none of these
20. Polystyrene is
(a) homopolymer
(b) copolymer
(c) composite material
(d) none of these
 Unit-3(Lecture 14-19)
1.Quantum wire is the material which has
A Two dimensions in the nano-meter range (< 100 nm)
ii. One dimensions in the nano-meter range (< 100 nm)
iii. Three dimensions in the nano-meter range (< 100 nm)
iv. None of the above
2. Nano-materials are used as catalyst because
i. Large surface area to volume ratio
ii. Small surface area to volume ratio
iii. High mechanical strength
iv. None of the above
3. Which of the following Nanomaterial is conductor?
i. Bucky ball, Carbon nano tube
ii. Diamond
iii. Carbon Nano tube
iv None of the above
4. Energy gap between bands in nanomaterial
i. Decreases
ii. Increases
iii. Increases than decreases
iv. None of the above
5. Which of the following statement/s is/are correct?
A. If one dimension of a substance is changed to nano-range then quantum dots are obtained
B. If one dimension of a substance is changed to nano-range then quantum wells are obtained
C. If three dimension of a substance is changed to nano-range then quantum wire are obtained
a. Only statement A is correct
b. Only statements B and C are correct
c. Only statement B is correct
d. Only statement C is correct
6.. Buckminster fullerenes contain
a. 60 Carbons with 12 pentagons and 20 hexagons
b. 60 Carbons with 20 pentagons and 12 hexagons
c. 60 Carbons with 20 pentagons and 20 hexagons
d. 60 Carbons with 12 pentagons and 12 hexagons
7. which of the following nanomaterial will absorb high frequency radiation?
a. 1 nm
b.2 nm
c.5 nm
d.10 nm
8. Friction is an undesirable process that results in:
A. wear and tear of the surfaces of the moving parts
B. loss of enormous energy as heat dissipation
C. lowered efficiency of the moving parts
D. all of the above
9. When oil is cooled at a specified rate, the temperature at which it becomes cloudy or
hazy is called
A.flash point
B. pour point
C.cloud point
D. fire point
10. The process of reducing the friction and wear between the two relatively moving
components of the machinery is termed as
A. esterification
B. sponification
C.emulsification
D.lubrication
11.When oil is cooled at a specified rate, the temperature at which it ceases to flow is called
A.flash point
B. pour point
C.cloud point
D. fire point.
12.What are the components of composites?
A. Matrix
B. reinforcement
C.Monomer
D. Both A and B
13. Which of them is compostite classified on the basis of matrix
A. OMC
B.MMC
C. CMC
D. All of the above
14. Which of them is compostite classified on the basis of Reinforcement
A. OMC
B. Laminar
C. CMC
D. All of the above
15.Which of them is semi solid lubricant?
A. Graphite
B.Grease
C. Edible oil
D.MoS2