Smartcare Tile Adhesive For Tile On Tile Application

SmartCare Tile Adhesive
PRODUCT CODE 5426
Tile-on-Tile Application
Asian Paints SmartCare Tile Adhesive for Tile-on-Tile Application is a single component cement based
polymer modified adhesive for fixing tiles over tiles on floors and walls in interiors as well as exteriors. The
product contains special additives that provide excellent bonding & grabbing properties.
PRODUCT BENEFITS
Specification Long pot life
Meets the requirements of IS 15477 (Specification for Long pot life and open time for smooth application
tile adhesive for ceramic and mosaic tiles)
No pre-soaking
Easy Application Needs no pre-soaking and water curing
Single component, ready-to-use mixture consisting of
Water Resistant and Flexibility
cement, sand and special additives
Excellent water resistance. Low shrinkage and greater
Excellent Adhesion flexibility for accommodating thermal or physical
Excellent adhesion ensuring that removal of old tiles, movements
breakage, debris or dust is done away with
Ready for use
Trafficable (ready for use) in 24 hours
PRODUCT FEATURES
AVAILABLE PACKS COLOURS AVAILABLE COVERAGE
Grey* 3.5-4.5 Kg/ m2

for a bed of
3 mm thickness
30 kg
Shelf life: 12 months from the date of manufacture *Please note: SmartCare Tile Adhesive for Tile-on- The actual coverage however might vary with
when stored in original packaging under normal dry Tile Application is a Grey coloured free flowing the type of surface & its flatness. For adequate
conditions. powder. coverage ensure that the surface is smooth, clean
and devoid of any defects or undulations.
RECOMMENDED USAGE
For permanent installation of ceramic, vitrified and porcelain tiles on tiles in interiors as well as exteriors. Can also be used for installation of heavy tiles and natural stones
(marble, granite) on tiled horizontal surfaces.
HOW TO APPLY
APPLICATION PROCESS
APPLICATION PROCEDURE APPLICATION PROCEDURE
Ensure that the existing tiles are firmly adhering to the substrate with a
STEP 1 STEP 6 Do not spread in more than 1 sq. m of area at a time.
uniform level and adequate joints.
STEP 2
For any hollow sounding areas, remove the tiles and make up with a STEP 7
Press the tile firmly into position with a slight sliding motion to ensure
polymer modified cement sand mortar. maximum contact surface.
The tiles should be cleaned with detergent and water first and then rinsed
STEP 3 STEP 8 Leave adequate joints between the tiles using spacers.
with water to remove any dirt/ laitance etc.
Mix Tile Adhesive into water, until a lump free mortar consistency is
STEP 4 STEP 9 Clean off excessive adhesive between the joints and on tiles.
achieved. Approx. 7-8 ltr. of water for a 30 Kg bag of tile adhesive.
STEP 5
Spread mixed tile adhesive at thickness 3-6 mm and comb with notched STEP 10
For best results, fill the tile joints with Asian Paints cement based or epoxy
trowel. based tile grout.
SmartCare Tile Adhesive
ADDITIONAL INFORMATION
PRECAUTIONS SAFETY FEATURES
> Grouting should not be done for at least 24 > Kindly refer to the MSDS for Asian Paints SmartCare Tile-on-Tile Application which gives
hours detailed information on safety measures while handling the material.
> Do not use for fixing heavy tiles or stones, > Store the bag tightly closed in a cool, dry place
marble, granite etc on vertical areas > Keep out of reach of children and away from eatables.
> May be harmful if swallowed. In case of ingestion seek immediate medical attention.
TECHNICAL DETAILS > Wear eye protection during application. In case of contact with eyes, rinse immediately with
plenty of water and if required seek medical advice.
> It is recommended to wear suitable nose pad during surface preparation, mixing, application
a. Form: Free flowing powder to avoid dust inhalation.
b. Color: Grey
c. Mix density: 1.85
d. Open time: 10 Minutes @ 30oC, 55% RH SPECIFICATIONS
e. Pot Life: 3 Hours
f. Curing time: 24 Hours
Test Parameter Minimum Requirement Tile-on-Tile Application
g. Cleaning tools: with water immediately
after use Shear Adhesion (Dry condition 24 hrs) 4kN Exceeds the requirements of IS 15477
Shear Adhesion (Dry condition 14 days) 10 k N Exceeds the requirements of IS 15477
Shear Adhesion (Heat aging conditions) 5kN Exceeds the requirements of IS 15477
Shear Adhesion (Wet conditions) 5kN Exceeds the requirements of IS 15477

Smartcare Tile Adhesive For Tile On Tile Application

Uploaded by

Copyright:

Available Formats

Smartcare Tile Adhesive For Tile On Tile Application

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Smartcare Tile Adhesive For Tile On Tile Application

Uploaded by

Copyright:

Available Formats

SmartCare Tile Adhesive

PRODUCT CODE 5426

Grey* 3.5-4.5 Kg/ m2

PRECAUTIONS SAFETY FEATURES

Shear Adhesion (Dry condition 14 days) 10 k N Exceeds the requirements of IS 15477

Shear Adhesion (Wet conditions) 5kN Exceeds the requirements of IS 15477

You might also like