Product Specification M240HTN01.

AU OPTRONICS CORPORATION

( ) Preliminary Specification
( v ) Final Specification

Module 24.0” Color TFT-LCD

Model Name M240HTN01.2

Customer Date Approved by Date

Howard Lee

Approved by Prepared by

Phoebe chen 2012/10/07

Note: This Specification is subject to change Desktop Display Business Group /

without notice. AU Optronics Corporation

Document version 1.0 1

 Product Specification M240HTN01.2

AU OPTRONICS CORPORATION

Content
1 HANDLING PRECAUTIONS...................................................................................................... 4

2 GENERAL DESCRIPTION......................................................................................................... 5
2.1 Display Characteristics ........................................................................................................................ 5
2.2 Optical Characteristics......................................................................................................................... 6

3 FUNCTIONAL BLOCK DIAGRAM .......................................................................................... 10

4 ABSOLUTE MAXIMUM RATINGS .......................................................................................... 11

4.1 TFT LCD Module ............................................................................................................................... 11
4.2 Backlight Unit .................................................................................................................................... 11
4.3 Absolute Ratings of Environment....................................................................................................... 11

5 ELECTRICAL CHARACTERISTICS........................................................................................ 13
5.1 TFT LCD Module ............................................................................................................................... 13
5.1.1 Power Specification ........................................................................................................................................13
5.1.2 Signal Electrical Characteristics .....................................................................................................................14
5.2 Backlight Unit .................................................................................................................................... 16

6 SIGNAL CHARACTERISTICS................................................................................................. 17
6.1 Pixel Format Definition....................................................................................................................... 17
6.2 Input Data Format Definition .............................................................................................................. 17
6.3 Signal Description.............................................................................................................................. 18
6.4 Timing Characteristics ....................................................................................................................... 20
6.5 Timing Diagram ................................................................................................................................. 21
6.6 Power ON/OFF Sequence................................................................................................................. 22

7 CONNECTOR AND PIN ASSIGNMENT .................................................................................. 23

7.1 TFT LCD Module ............................................................................................................................... 23
7.1.1 Pin Assignment ...............................................................................................................................................23
7.2 LED Connector on Backlight Unit ...................................................................................................... 24
7.2.1 LED Pin assignment .......................................................................................................................................24
7.2.2 LED Connector Dimension .............................................................................................................................25
7.2.3 LED Mating housing dimension ......................................................................................................................25

8 RELIABILITY TEST ................................................................................................................. 26

9 SHIPPING LABEL ................................................................................................................... 27

10 MECHANICAL CHARACTERISTICS ...................................................................................... 28

11 PACKING SPECIFICATION .................................................................................................... 30

11.1 Packing Flow ..................................................................................................................................... 30
11.2 Pallet and Shipment Information........................................................................................................ 31
Document version 1.0 2
 Product Specification M240HTN01.2

AU OPTRONICS CORPORATION

Records of Revision

Version and Date Page Old description New Description Remark

Preliminary
00
Specification
1.0 6 Blue Y : 0.040 0.070 0.100 Blue Y : 0.035 0.065 0.095

20

16 Light Bar Operation Voltage : Light Bar Operation Voltage :

Min: - Min : 26.55

Document version 1.0 3

 Product Specification M240HTN01.2

AU OPTRONICS CORPORATION

1 Handling Precautions

1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth
when handling.
7) Do not open or modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) In case if a Module has to be put back into the packing container slot after once it was taken out
from the container, do not press the center of LED light bar edge. Instead, press at the far ends
of the LED light bar edge softly. Otherwise the TFT Module may be damaged.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the
Interface Connector of the TFT Module.
11) After installation of the TFT Module into an enclosure, do not twist nor bend the TFT Module
even momentary. At designing the enclosure, it should be taken into consideration that no
bending/twisting forces are applied to the TFT Module from outside. Otherwise the TFT Module
may be damaged.
12) Small amount of materials having no flammability grade is used in the LCD module. The LCD
module should be supplied by power complied with requirements of Limited Power Source
(IEC60950 or UL1950), or be applied exemption.
13) Avoid touching COF position while doing mechanical design.
14) While storing modules as spares for a long time, the following precautions are necessary:

Store modules in a dark place. Do not expose them to sunlight or fluorescent light.

Keep the temperature between 5°C and 35°C at normal humidity.

Document version 1.0 4

 Product Specification M240HTN01.2

AU OPTRONICS CORPORATION

2 General Description
This specification applies to the 24 inch-FHD color a-Si TFT-LCD Module M240HTN01.2. The
display supports the FHD - 1920(H) x 1080(V) screen format and 16.7M colors (RGB 6-bit + Hi-FRC
data). The light source of this TFT-LCD module is W-LED. All input signals are 2-channel LVDS
interface and this module doesn’t contain a driver for backlight.

2.1 Display Characteristics

The following items are characteristics summary on the table under 25°C condition:

Items Unit Specification

Screen Diagonal [mm] 609.7 (24.0”)
Active Area [mm] 531.36 (H) x 298.89 (V)
Pixels H x V 1920(x3) x 1080
Pixel Pitch [um] 276.75 (per one triad) ×276.75
Pixel Arrangement R.G.B. Vertical Stripe
Display Mode TN Mode, Normally White
White Luminance ( Center ) [cd/m2] 250 cd/m2 (Typ.)
Contrast Ratio 1000 (Typ.)
Optical Response Time [msec] 5ms (Typ., on/off)
Nominal Input Voltage VDD [Volt] + 5.0 V
17.55 watt
Power Consumption
[Watt] VDD line : PDD (typ), All black pattern at 60Hz =3.25W
(VDD line + LED line)
LED line : PBLU (typ) = 14.3W
Weight [g] 1885g
Physical Size [mm] 556.0 (W) x 323.2 (H) x 11.5(D) (Typ.)
Electrical Interface Dual channel LVDS
Support Color 16.7M colors (RGB 6-bit + Hi_FRC)
Surface Treatment Anti-Glare, 3H
Temperature Range
Operating [°C] 0 to +50
Storage (Shipping) [°C] -20 to +60
RoHS Compliance RoHS Compliance
TCO Compliance TCO 6.0 Compliance

Document version 1.0 5

 Product Specification M240HTN01.2

AU OPTRONICS CORPORATION

2.2 Optical Characteristics

The optical characteristics are measured under stable conditions at 25°C:

Item Unit Conditions Min. Typ. Max. Note

Horizontal (Right) 75 85 -
CR = 10 (Left) 75 85 -
Viewing Angle [degree] 2
Vertical (Up) 70 80 -
CR = 10 (Down) 70 80 -

Contrast Ratio Normal Direction 600 1000 - 3

Rising Time (TrR) - 3.5 7.4

Response Time [msec] Falling Time (TrF) - 1.5 2.6 4
Rising + Falling - 5 10
Red x 0.615 0.645 0.675
Red y 0.302 0.332 0.362
Color / Chromaticity Green x 0.285 0.315 0.345
Coordinates (CIE) Green y 0.589 0.619 0.649
5
Blue x 0.121 0.151 0.181
Blue y 0.035 0.065 0.095
White x 0.283 0.313 0.343
Color Coordinates (CIE) White
White y 0.299 0.329 0.359
Central Luminance [cd/m2] 200 250 - 6
Luminance Uniformity [%] 75 80 - 7
Crosstalk (in 60Hz) [%] 1.5 8
Flicker dB -20 9

Document version 1.0 6

 Product Specification M240HTN01.2

AU OPTRONICS CORPORATION

Note 1: Measurement Method

The LCD module should be stabilized at given temperature for 30 minutes to avoid abrupt
temperature change during measuring (at surface 35°C). In order to stabilize the luminance, the
measurement should be executed after lighting Backlight for 30 minutes in a stable, windless and
dark room.

Photo Detector

Measured Distance

LCD Panel
TFT-LCD Module

Center of the screen

Note 2: Definition of Viewing Angle measured by ELDIM (EZContrast 88)

Viewing angle is the measurement of contrast ratio ≧10, at the screen center, over a 180°
horizontal and 180° vertical range (off-normal viewing angles). The 180° viewing angle range is
broken down as follows; 90° (θ) horizontal left and right and 90° (Φ) vertical, high (up) and low
(down). The measurement direction is typically perpendicular to the display surface with the screen
rotated about its center to develop the desired measurement viewing angle.

Document version 1.0 7

 Product Specification M240HTN01.2

AU OPTRONICS CORPORATION

Note 3: Contrast Ratio measured by TOPCON SR-3

Note 4: Definition of Response time measured by Westar TRD-100A
The output signals of photo detector are measured when the input signals are changed from “Full
Black” to “Full White” (rising time, TrR), and from “Full White” to “Full Black” (falling time, TrF),
respectively. The response time is interval between the 10% and 90% (1 frame at 60 Hz) of
amplitudes.
% T rF T rR

100
90
Optical
White Black Black White
response
10
0
1 Frame 1 Frame

TrR + TrF = 5 msec (typ.).

Note 5: Color Chromaticity and Coordinates (CIE) measured by TOPCON SR-3

Note 6: Central Luminance measured by TOPCON SR-3

Note 7: Luminance Uniformity of these 9 points defined as below and measured by TOPCON
SR-3

Minimum Luminance in 9 points (1 - 9)

Uniformity =
Maximum Luminance in 9 Points (1 - 9)

Document version 1.0 8

 Product Specification M240HTN01.2

AU OPTRONICS CORPORATION

Note 8: Crosstalk defined as below and measured by TOPCON SR-3

CT = | YB – YA | / YA × 100 (%)

Where
YA = Luminance of measured location without gray level 0 pattern (cd/m2)
YB = Luminance of measured location with gray level 0 pattern (cd/m2)

Note 9: Test Pattern Sub-checker Pattern measured by TOPCON SR-3

RGBRGB
Gray Level = L127

RGBRGB

Gray Level = L0
RGBRGB

Method: Record dBV & DC value with TRD-100

Amplitude
AC

DC

Time

AC Level(at 30 Hz)
Flicker (dB) = 20 log
DC Level

Document version 1.0 9

 Product Specification M240HTN01.2

AU OPTRONICS CORPORATION

3 Functional Block Diagram

The following diagram shows the functional block of the 24.0 inch Color TFT-LCD Module:

AUO
ASIC G1

Y-Driver IC
Timing
LVDS Controller
LVDS TFT-LCD
Connector

Receiver
1920(x3) x 1080
miniLVDS
Transmitter Pixels
+5V X-Driver IC
G1080
D1 D5760

LED
Backlight

DC/DC Gamma

Converter Correction

I/F + X-PCB
DC
LED Driver on system

I/F PCB Interface:

MSCKT2407P30HB (STM)

AL230F-A0G1D-P (P-TWO)

Mating Type:
FI-X30HL(Locked Type)

Document version 1.0 10

 Product Specification M240HTN01.2

AU OPTRONICS CORPORATION

4 Absolute Maximum Ratings

Absolute maximum ratings of the module are listed as follows:

4.1 TFT LCD Module

Item Symbol Min Max Unit Conditions
Logic/LCD Drive VDD -0.3 6.0 [Volt] Note 1, 2

4.2 Backlight Unit

Item Symbol Min Max Unit Conditions
IRLED1
IRLED2 Note 1,2,5
LED Forward Current 0 150 [mA]
IRLED3 100% duty
IRLED4
IPLED1
IPLED2 Note 1,2,5
LED Pulse Forward Current - 210 [mA]
IPLED3 10% duty @100Hz
IPLED4
LED forward Voltage variation Note 1,2
ΔVf - 1.8 [Volt]
(per string variation)

4.3 Absolute Ratings of Environment

Item Symbol Min. Max. Unit Conditions
Operating Temperature TOP 0 +50 [°C] Note 3
Glass Surface Temperature Note3
TGS 0 +65 [°C]
(Operation) Note4
Operation Humidity HOP 5 90 [%RH]
Storage Temperature TST -20 +60 [°C] Note 3
Storage Humidity HST 5 90 [%RH]
Note 1: With in Ta (25 °C)
Note 2: Permanent damage to the device may occur if exceeding maximum values
Note 3: Temperature and relative humidity range are shown as the below figure.
1. 90% RH Max ( Ta ≦39°C)
2. Max wet-bulb temperature at 39°C or less. ( Ta ≦39°C)
3. No condensation
Note 4: Function Judged only
Note 5: IRLED1,2,3,4 and IPLED1,2,3,4 define as per strings LED current.

Document version 1.0 11

 Product Specification M240HTN01.2

AU OPTRONICS CORPORATION

Operating Range Storage Range

Document version 1.0 12

 Product Specification M240HTN01.2

AU OPTRONICS CORPORATION

5 Electrical Characteristics
5.1 TFT LCD Module

5.1.1 Power Specification

Input power specifications are listed as follows:

Symbol Description Min Typ. Max Unit Conditions

Logic/LCD Drive
VDD 4.5 5.0 5.5 [Volt] +/-10%
Voltage

- 0.65 0.78 [A] VDD= 5.0V, All Black Pattern at 60 Hz

IDD1 Input Current
- 0.8 0.96 [A] VDD= 5.0V, All Black Pattern at 75 Hz

- 3.25 3.9 [Watt] VDD= 5.0V, All Black Pattern at 60 Hz

PDD1 VDD Power
- 4 4.8 [Watt] VDD= 5.0V, All Black Pattern at 75 Hz

IRush Inrush Current - - 3 [A] Note 1

Allowable Logic/LCD
VDDrp - - 500 [mV] p-p VDD= 5.0V, All Black Pattern at 75 Hz
Drive Ripple Voltage

Note 1: Measurement Conditions:

The duration of rising time of power input is 470 us.

Document version 1.0 13

 Product Specification M240HTN01.2

AU OPTRONICS CORPORATION

5.1.2 Signal Electrical Characteristics

(1) DC Characteristics of each signal are as following:

Symbol Description Min Typ Max Units Conditions

Differential Input High VCM = 1.2V
VTH - +50 +100 [mV]
Threshold Note 1
Differential Input Low VCM = 1.2V
VTL -100 -50 - [mV]
Threshold Note 1

Input Differential
│VID│ 100 - 600 [mV] Note 1
Voltage
Differential Input VTH-VTL = 200MV (max)
VCM +1.0 +1.2 +1.5 [V]
Common Mode Voltage Note 1

Note 1: LVDS Signal Waveform

Document version 1.0 14

 Product Specification M240HTN01.2

AU OPTRONICS CORPORATION

(2) AC Characteristics

Symbol Description Min Max Units Conditions

Maximum deviation of input clock
FDEV - ±3 %
frequency during SSC
Maximum modulation frequency of
FMOD - 300 KHz
input clock during SSC

Freq

Fmax
Fcenter * FDEV

Fmin

1
FMOD

Time

< Spread Spectrum>

Document version 1.0 15

 Product Specification M240HTN01.2

AU OPTRONICS CORPORATION

5.2 Backlight Unit

Parameter guideline for LED driving is under stable conditions at 25 °C (Room Temperature):

Symbol Description Min. Typ. Max. Unit Note

[mA]
IRLED LED Operation Current - 120 126 Note 1

Light Bar Operation Voltage

VLB 26.55 29.7 32.4 [Volt] Note 2
(for reference)

PBLU BLU Power Consumption (for reference) - 14.3 16.3 [Watt] Note 3

[Hour]
LTLED LED Life Time (Typical) 30,000 - - Note 4

Each module consists of 36 pcs LED ( 4 strings x 9 pcs / string )

Note 1: The specified current is 100% duty of LED chip input current, IRLED1,2,3,4 define as per strings LED current.

Note 2: The value showed is one string operation voltage.

Note 3: PBLU = VLED *( IRLED1+IRLED2+IRLED3+IRLED4)

Note 4: Definition of life time: Brightness becomes to 50% of its original value. The minimum life time of LED unit is on
the condition of IRLED = 120mA and 25±2°C (Room Temperature).

Document version 1.0 16

 Product Specification M240HTN01.2

AU OPTRONICS CORPORATION

6 Signal Characteristics
6.1 Pixel Format Definition

Following figure shows the relationship between the input signals and LCD pixel format.

1 2 1919 1920

1st Line R G B R G B R GB R G B

1080 Line R G B R G B R GB R G B

6.2 Input Data Format Definition

Note 1: R/G/B data 7:MSB, R/G/B data 0:LSB O = “Odd Pixel Data” E = “Even Pixel Data”

Document version 1.0 17

 Product Specification M240HTN01.2

AU OPTRONICS CORPORATION

6.3 Signal Description

PIN # SIGNAL NAME DESCRIPTION

1 RxOIN0- Negative LVDS differential data input (Odd data)
2 RxOIN0+ Positive LVDS differential data input (Odd data)
3 RxOIN1- Negative LVDS differential data input (Odd data)
4 RxOIN1+ Positive LVDS differential data input (Odd data)
5 RxOIN2- Negative LVDS differential data input (Odd data, DSPTMG)
6 RxOIN2+ Positive LVDS differential data input (Odd data, DSPTMG)
7 GND Power Ground
8 RxOCLK- Negative LVDS differential clock input (Odd clock)
9 RxOCLK+ Positive LVDS differential clock input (Odd clock)
10 RxOIN3- Negative LVDS differential data input (Odd data)
11 RxOIN3+ Positive LVDS differential data input (Odd data)
12 RxEIN0- Negative LVDS differential data input (Even data)
13 RxEIN0+ Positive LVDS differential data input (Even data)
14 GND Power Ground
15 RxEIN1- Negative LVDS differential data input (Even data)
16 RxEIN1+ Positive LVDS differential data input (Even data)
17 GND Power Ground
18 RxEIN2- Negative LVDS differential data input (Even data)
19 RxEIN2+ Positive LVDS differential data input (Even data)
20 RxECLK- Negative LVDS differential clock input (Even clock)
21 RxECLK+ Positive LVDS differential clock input (Even clock)
22 RxEIN3- Negative LVDS differential data input (Even data)
23 RxEIN3+ Positive LVDS differential data input (Even data)
24 GND Power Ground
25 NC No connection (for AUO test only. Do not connect)
26 NC No connection (for AUO test only. Do not connect)
27 NC No connection (for AUO test only. Do not connect)
28 VDD Power +5V
29 VDD Power +5V
30 VDD Power +5V

Note 1: Input signals of odd and even clock shall be the same timing.

Document version 1.0 18

 Product Specification M240HTN01.2

AU OPTRONICS CORPORATION

LVDS C/N PIN 1

L/B C/N PIN 1

Document version 1.0 19

 Product Specification M240HTN01.2

AU OPTRONICS CORPORATION

6.4 Timing Characteristics

The input signal timing specifications are shown as the following table

Signal Item Symbol Min Typ Max Unit

Period Tv 1092 1130 1818 Th
Vertical
Active Tdisp(v) 1080 1080 1080 Th
Section
Blanking Tbp(v)+Tfp(v)+PWvs 12 50 738 Th
Period Th 1034 1050 1100 Tclk
Horizontal
Active Tdisp(h) 960 960 960 Tclk
Section
Blanking Tbp(h)+Tfp(h)+PWhs 74 90 140 Tclk
Period Tclk 10.6 14.0 17.7 Ns
Clock
Frequency Freq 56.5 71.2 94 MHz
Frame rate Frame rate VFreq 50 60 76 Hz
Hsync Hsync
HFreq 55 68 91 KHz
Frequency Frequency

Note 1: DE mode only

Document version 1.0 20

 Product Specification M240HTN01.2

AU OPTRONICS CORPORATION

6.5 Timing Diagram

Tv
M pixel

Tblk(v) Tdisp(v)
Y

N Line
Th

DE

N 1 2 3 4 N
Invalid Data Invalid Data
RGB Data
Line Line Line Line Line Line

CLK

Tclk
Th

Tdisp(h) Tblk(h)

DE

RGB Data Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel
Invalid Data Invalid Data
(Odd) M-7 M-5 M-3 M-1 1 3 5 7 9 11 M-5 M-3 M-1 1 3

RGB Data Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel PixelPixel Pixel Pixel Pixel
Invalid Data Invalid Data
(Even) M-6 M-4 M-2 M 2 4 6 8 10 12 M-4 M-2 M 2 4

Document version 1.0 21

 Product Specification M240HTN01.2

AU OPTRONICS CORPORATION

6.6 Power ON/OFF Sequence

VDD power and lamp on/off sequence are as follows. Interface signals are also shown in the
chart. Signals from any system shall be Hi-Z state when VDD is off.

T1
90% 90%

10% 10%
Power Supply VDD T2 T5 T6 T7

LVDS Signal VALID

DATA

T3 T4

Backlight On

Power Sequence Timing

Value
Parameter Unit
Min. Typ. Max.
T1 0.5 - 10 [ms]
T2 0 - 50 [ms]
T3 500 - - [ms]
T4 100 - - [ms]
[ms]
T5 0 - 50
Note1,2
[ms]
T6 5 - 100
Note1,2
T7 1000 - - [ms]

Note1 : Recommend setting T5 = 0ms to avoid electronic noise when VDD is off.

Note2 : During T5 and T6 period , please keep the level of input LVDS signals with Hi-Z state.

Document version 1.0 22

 Product Specification M240HTN01.2

AU OPTRONICS CORPORATION

7 Connector and Pin Assignment

Physical interface is described as for the connector on module. These connectors are capable of
accommodating the following signals and will be following components.

7.1 TFT LCD Module

Connector Name / Designation Interface Connector / Interface Card

P-TWO
Manufacturer
STM

MSCKT2407P30HB (STM)
Type Part Number
AL230F-A0G1D-P (P-TWO)

Mating Housing Part Number FI-X30HL (Locked Type)

7.1.1 Pin Assignment

Pin# Signal Name Pin# Signal Name

1 RxOIN0- 2 RxOIN0+
3 RxOIN1- 4 RxOIN1+
5 RxOIN2- 6 RxOIN2+
7 GND 8 RxOCLKIN-
9 RxOCLKIN+ 10 RxOIN3-
11 RxOIN3+ 12 RxEIN0-
13 RxEIN0+ 14 GND
15 RxEIN1- 16 RxEIN1+
17 GND 18 RxEIN2-
19 RxEIN2+ 20 RxECLKIN-
21 RxECLKIN+ 22 RxEIN3-
23 RxEIN3+ 24 GND
NC (for AUO test only. Do not NC (for AUO test only. Do not
25 26
connect) connect)
NC (for AUO test only. Do not
27 28 VDD
connect)
29 VDD 30 VDD

Document version 1.0 23

 Product Specification M240HTN01.2

AU OPTRONICS CORPORATION

7.2 LED Connector on Backlight Unit

This connector is mounted on LED light bar.

Connector Name / Designation Light Bar Connector

Manufacturer ENTERY INDUSTRIAL CO., LTD.

3707K-S06N-21 (BLACK)
Type Part Number
(Locking Type, Wire Harness)

7.2.1 LED Pin assignment

Pin# Signal Name

1 IRLED1 (current out)
2 IRLED2 (current out)
3 VLED (voltage in)
4 VLED (voltage in)
5 IRLED3 (current out)
6 IRLED4 (current out)

Document version 1.0 24

 Product Specification M240HTN01.2

AU OPTRONICS CORPORATION

LED Connector Dimension

H × V × D = 7.9 × 6.5 × 4.25, Pitch = 1.0(unit = mm )

7.2.2 LED Mating housing dimension

Document version 1.0 25

 Product Specification M240HTN01.2

AU OPTRONICS CORPORATION

8 Reliability Test
Environment test conditions are listed as following table.

Items Required Condition Note

Temperature Humidity Bias (THB) Ta= 50°C, 80%RH, 300 hours
High Temperature Operation (HTO) Ta= 50°C, 50%RH, 300 hours
Low Temperature Operation (LTO) Ta= 0°C, 300 hours
High Temperature Storage (HTS) Ta= 60°C, 300 hours
Low Temperature Storage (LTS) Ta= -20°C, 300 hours

Acceleration: 1.5 Grms

Vibration Test Wave: Random
(Non-operation) Frequency: 10 - 200 Hz
Duration: 30 Minutes each Axis (X, Y, Z)

Acceleration: 50 G
Shock Test Wave: Half-sine
(Non-operation) Active Time: 20 ms
Direction: ±X, ±Y, ±Z (one time for each Axis)

Drop Test Height: 46 cm, package test

Thermal Shock Test (TST) -20°C/30min, 60°C/30min, 100 cycles Note 1
On/Off Test On/10sec, Off/10sec, 30,000 cycles
Contact Discharge: ± 15KV, 150pF(330Ω ) 1sec,
15 points, 25 times/ point
ESD (Electro Static Discharge) Note 2
Air Discharge: ± 15KV, 150pF(330Ω ) 1sec
15 points, 25 times/ point
Operation: 18,000 ft
Altitude Test
Non-Operation: 40,000 ft

Note 1: The TFT-LCD module will not sustain damage after being subjected to 100 cycles of rapid temperature change.
A cycle of rapid temperature change consists of varying the temperature from -20°C to 60°C, and back again. Power is
not applied during the test. After temperature cycling, the unit is placed in normal room ambient for at least 4 hours
before power on.

Note 2: EN61000-4-2, ESD class B: Certain performance degradation allowed:

No data lost

Self-recoverable

No hardware failures

Document version 1.0 26

 Product Specification M240HTN01.2

AU OPTRONICS CORPORATION

9 Shipping Label
The label on the panel is shown as below:

Manufactured XX/XX
Model No: M240HTN01.2
AU Optronics

Note 1: For Pb Free products, AUO will add for identification.

Note 2: For RoHS compatible products, AUO will add for identification.

Note 3: For China RoHS compatible products, AUO will add for identification.

Note 4: The Green Mark will be presented only when the green documents have been ready by AUO Internal Green
Team.

Document version 1.0 27

 Product Specification M240HTN01.2

AU OPTRONICS CORPORATION
10 Mechanical Characteristics

Document version 1.0 28

 Product Specification M240HTN01.2

AU OPTRONICS CORPORATION

Avoid touching COF position

when doing mechanical design

Document version 1.0 29

 Product Specification M240HTN01.2

AU OPTRONICS CORPORATION

11 Packing Specification
11.1 Packing Flow

Module Top cover

Put top cover

Paste protect film
10 pcs/carton

Paste lamp wire Cushion

” H ” Tape
Carton
1pcs Module/ESD

Corner angle Moisture-proof film

Stretch film

Label PET band

Corner angle

Pallet

Document version 1.0 30

 Product Specification M240HTN01.2

AU OPTRONICS CORPORATION

11.2 Pallet and Shipment Information

Specification
Item Remark
Q'ty Dimension Weight(kg)
1 Panel 1 556(H)mm x 323.2(V)mm x 9.08(D)mm 1.885 Note 1
2 Cushion 1 -- 1.7
without Panel & cushion
3 Box 1 406(L)mm x 281(W)mm x 651(H)mm 1.2 Note 1

with panel & cushion

4 Packing Box 10 pcs/Box 406(L)mm x 281(W)mm x 651(H)mm 21.75 Note 1

5 Pallet 1 1150(L)mm x 840(W)mm x 138(H)mm 12 Note 1

16
6 Pallet after Packing 1140(L)mm x 830(W)mm x 1440(H)mm 360 Note 1
boxes/pallet
Note 1: Estimated value which is subject to change based on real measured data.

Document version 1.0 31