Mektek2 Manual Jan 08 PDF

Mektek2 Manual V1.
0 English 1
Operator's Manual
Mektek 2
(Lite & Professional Versions)
Version 1.0 onwards
Reprogramming coin mechanisms
Mektek International Ltd Tel: (44) 1628 525525

Unit 20 Soho Mills Ind Estate Fax: (44) 1628 525549
Wooburn Green Email: [email protected]
Bucks Website: www.mektekinternational.com
HP10 0PF
U.K.
Mektek2 V1.0 English

Mektek2 Manual V1.0 English 2
Contents
Installation
PC requirements, software installation, connection, configuring your system,
Programmer to PC connection, PSU.
How the programmer works
Validator function, programmer function.
Credits (Lite version only)
What is a credit, checking & loading credits.
Data storage devices
Purpose, Coin Controls/NRI EEPROM, Mars PROM & E+1
Getting started
Looms, Coinset Files, coins.
Basic reprogramming routines
Mars – example MS1600
Coin Controls – example C120
Wizards - Add/replace a coin, Slug Fix, Edit Limits.
Discriminating against a known slug
Using Coinset file and Slug Fix Wizard
Additional features:
Mars - PROM Utilities, Flier limits.
Coin Controls/NRI - EEPROM Utilities, Cloning routines
Reprogramming by mechanism type
Mars: MS1000, MS1400, ME111/MS111, ME181, MS130B1
Coin Controls: C120, C220B, C335, C435/C435A, C450, C220/Sentinel
NRI: G13, G10, G40
Appendix
Keeping up to date
Obtaining Coinset Files, Updating operating software, technical help.
Additional features included in later version operating software
Mars-program both Segments, Language options.
Tables:
Fault finding table
Description of generic Coinset Files
Mechanisms supported
Looms cross reference
Installation
Minimum PC requirements
IBM PC or compatible, Pentium 100MHz or faster
16 Mbyte RAM (32 Mbyte recommended)
20 Mbytes free hard disc space
Windows 95, 98, ME or XP
One free RS232 serial port with 9-pin connector
(If only USB ports are fitted use a USB/Serial converter)
Standard Keyboard and Mouse
CD Rom drive
Microsoft Word or similar
Internet & Email links are recommended for credit requests & software downloads.
Software installation
?? Insert the Installation CD and select Run from the Start menu. Select file
name Setup.exe from the CD drive and click on OK. Follow the on-screen
instructions.
?? Copy the CD folder Coinsets to C:\Program Files\Mektek folder
?? The contents of the folder Manuals/Language can be copied from the CD
into a suitable folder for reference.
Connecting the programmer to the PC
?? Connect the grey flex from the Programmer to a serial port on your PC.
?? If using a USB/serial converter firstly identify the COM port to bu used by
attaching the converter and rebooting the PC. Go to Control
Panel/System/Devices (or similar) and identify to which COM port the
converter is assigned. This is the COM port to be used for Mektek.
?? Connect the 16v power supply unit to the Programmer and mains supply
and switch on.
Mains supply via PSU
RS232 cable to PC serial port.
PROM programming socket
Sockets for looms to connect validator for

programming
Socket for G13 Totaliser only
On/off switch
Configuration
?? Start the Programmer from Windows by clicking on Start, Programs,
Mektek and Mektek Programmer.
?? When the Main Menu appears select the COM port to be used, Language
required and change the number of credits remaining before the Credits
Warning Level is displayed if required.
?? Click on Save Config and Exit. To modify settings select Change

Configuration in the main menu which will appear when the Programmer is
restarted.
?? If an incorrect COM port has been selected an error message will appear
when the program is restarted. Select To bring up the main menu again
delete the file “config0000” file in the folder containing the Mektek
Programmer software and restart the program. Select the correct COM
port and save the configuration.
How the programmer works

Validator function
In principle, validators measure the outputs from in-built sensors as a coin
passes them. The values are then compared with a table of preset values held
in memory. If the outputs are all within the limits specified for one of the
programmed coins in the table the coin is accepted and a signal sent to the
host machine that a coin type A, B, 1, 2, etc has been accepted. Values are
usually assigned to each coin outside of the validator except in the case of a
totaliser. Eg ME181, G13 totaliser.
Programmer function
The Mektek Programmer takes the outputs from the measuring sensors in a
validator as coins are dropped through, performs a statistical analysis on the
values and generates limits according to a supplied Coinset File appropriate to
the validator and to the coins to be programmed. The new limits can be
examined for overlaps, adjusted if necessary and then transferred to a plug-in
memory device which is inserted into a socket on the validator for a Mars unit
or directly into the EEEPROM for Coin Controls or NRI. Coins are passed
through the validator to confirm acceptance.
Wizards are provided to eliminate slugs and add/replace a coin.
Credits (Lite version only)

Note: Professional versi on is unlimited usage.
What is a credit?
Each time the programmer is used for a chargeable operation one or more
credits are deducted from the total held in the Programmer in a similar manner
to a pre-pay mobile telephone. For example the routine for programming an
ME115 validator, including coin data gathering, transferring the data to an E+1
device and testing coin acceptance would consume one credit. A warning
message is displayed when the credits need replenishing. Credits can only be
purchased from the supplier of your Programmer.
Checking credits
To check the number of credits remaining in the Programmer or to order more
credits start the Programmer & click on Load Credits. The number of credits
available is shown along with the number used since last replenishment.
Loading credits
?? To replenish credits start the Programmer and click on Load Credits.
?? Click on the Number Requested box and enter the amount required
?? Click on Request More Credits and a unique code message of up to 40
characters will appear in the Code String box. Copy (double click on the
box to select the field, right click on the mouse and click on Copy) then
paste this number into an Email or Fax and send to your supplier.
?? Once payment has been received a similar Code String will be returned.
NOTE:
Do not request further

credits if an outstanding
credit request exists.
If a Fault Message such

as "Not a Valid Credit
Issue Message"
appears check the
Message Table below
for details .
?? Paste the new code message into the box and click on Load New Credits.
?? The Number Loaded will be displayed and added to those available.
?? Click on Return to Main Menu to exit.
Loading Credits Message Table

Message Cause/Action
Not a valid credit issue message Invalid code string - incomplete or wrongly
Checksum error entered Code String.
Message not accepted Check & re-enter figure.
Contact Mektek for assistance.
Credit Issue Message not for this Each Programmer has a unique serial number.
serial number This Code String is only valid for the box from
which it was requested.
Incorrect VAR code Credit issue has the wrong Programmer
supplier code.
Contact your Programmer supplier or Mektek.
Incorrect code Security code does not match. An old Code
String has been entered.
Data storage devices

Purpose
The limits generated for each of the coins to be accepted and occasionally
values, inhibits and outputs are stored in a memory device .
Coin Controls & NRI EEPROM:
The data is stored in an integral EEPROM which can be reprogrammed.
Mars PROM & Mektek E+1:
For Mars units the data is stored in a separate memory device plugged into the
validator. The original – and now obsolete – PROM used in the Mars units is a
one-shot device which cannot be reused. The Mektek E+1 device used in
place of the PROM can be reprogrammed as many times as required, doing
away with the need to replace the expensive PROM each time a validator is
reprogrammed.
PROM Segments:
Dependent on the validator the PROM will be either a 1k or a 2k device. The
correct size PROM must be used but the same E+1 device is suitable for both
applications. In the 1k type the storage is divided into segments 1 and 2, each
of which can hold the limits for 6 coins (A1, B1, C1, D1, E1, F1). The segment
to be used can be switched from one to the other but only one segment can be
active at a time. In the case of a PROM switching is done by links or switches
on the validator or by withdrawing the device and removing one of it’s pins. On
an E+1 device Switch 1 is set On or Off. In the 2k type there are four
segments with the two additional segments being used to hold additional coin
limits or values.
E+1V - suitable for both 1k & Switch setting

2k vending applications.
ON
Coloured Blue. (Red for
MS1400 only)
E+1A - suitable for both 1k &

2k amusement & gaming
applications. Coloured green. 1 2
Getting Started
?? Read the remainder of this Operator’s Manual.
?? Using the Loom Cross Reference Table supplied with the Programmer
check that you have the required loom(s) for the mech type to be
programmed. If a Special Order loom is necessary, contact your supplier.
?? A suitable Coinset File – which instructs the Programmer unit on mech
type, coin channels, quantity of coins to be dropped, limit calculations,
segments used etc. – is needed. The Coinset File must be suitable for the
mech type and coin configuration that you are planning to program. See
the Appendix for a list of Coinset Files that are included with the
installation CD. If a suitable file is not included check the Coinset
Download page of the website www.mektekinternational.com or contact
your Programmer supplier.
?? Obtain 20 coins of each denomination to be programmed.
Basic reprogramming routines

All mech types:
?? Clean and dry the path of the coins through the validator using a soft cloth
and a foaming non-solvent cleaner.
?? Start Coin Programming System from Start, Programs, Mektek.
?? Connect validator to programmer using appropriate loom(s) In this
example use loom E1 from socket 4 to rear of validator.
See “Reprogramming by coin mech type” and Appendix for details.
?? Mount the validator in the correct alignment
?? Switch on programmer box.
?? Select the correct mech make and type and click on Validator test.
?? Drop current coins through the mech and check acceptance to confirm that
the validator is working correctly.
MARS – example MS1600

?? Click on MARS
?? Click on Run Coinset File
HELP:
If “No response from programmer box”
appears:
.Switch box off/on
.Check PC to box loom
. Reboot system
If “No validator detected” appears:
. Check box to validator loom?
. Suspect faulty validator
. Switch box off/on
?? Open the appropriate coinset file (In this example MK03–MS1000 to add 3
new coins to Segment 2 and copy existing coins from Segment 1 to new
Segment 1) The new Coins will be 50c, 1Euro & 2Euro.
NOTES:
Coin Channel: Coin A1
goes into the first
channel A of segment 1
in the E+1. Coin B1 goes
into the second channel
B of segment 1 etc. Coin
A2 would be the A coin
in segment 2.
Number of Coins
Remaining: Will
decrease to zero as
coins requested are
dropped through the
validator.
Mech Type : The family
of mechs suitable for use
with this Coinset File.
?? Once the Coinset File has been opened the following type of message will
appear. The Coin Type may be generic such as A1 or specific such as 5c.
?? Click on OK to start the coin drop (Click on Cancel to skip this coin and go
to the next one)
?? Drop the coins through the validator until the Number of Coins
Remaining field drops to zero and the following message appears.
NOTE:
*The readings for Thickness, Diameter and Material
are displayed for each coin as it is dropped along with
various statistics.
*The upper and lower limit for each parameter is
calculated and updated as each coin drops.
?? Click on OK to repeat the process for the rest of the coins which require
data gathering or Cancel to Skip this channel and pass on to the next.
?? Click on OK when the message “Data Gathering Complete appears.

NOTE:
The limits for the old coins
will now be read from the old
PROM or E+1 on the
validator ready to be put into
the E+1
?? Remove the old PROM or E+1 from the validator and insert it into the
PROM socket on the top of the Programmer. Ensure that the notch at the
end of the PROM is next to the red spot beside the socket (Opposite the
lever) and push down the lever.
?? Click on OK to copy the data.
NOTE:
Having collected all the data
required the limits are generated
and will be displayed on the next
page.
?? Remove the PROM from the socket and click on OK and the Limits Screen
appears.
NOTE:
*The limits
calculated for
the Euro
coins are
ready to
transfer to
the E+1
*Segment 2
is displayed.
To read the
rest of the
data, click on
the segment
in Display
PROM
Segments .
?? The estimated acceptance of each coin is displayed. If required adjust the

limits by overtyping then click on Change Limits to see the revised
Acceptance. Adjust if necessary. Clicking on Restore Limits will restore
the limits to their original values.
?? Select the type of device to programme in Target Prom type
?? Click on Program New PROM
NOTE:
The number of credits
which will be deducted to
complete the programming
is displayed.
?? Click on OK to proceed.
ON
1 2
?? Insert an E+1 in the socket of the Programmer.

?? Check that both switches are ON

?? Click on OK to programme the device.
?? The E+1 has been programmed

?? Set Switch 2 to OFF to allow verification of the data and to prevent
erasure of E+1 when fitted to validator.
?? Click on OK to verify
?? Click on OK to complete.
?? Remove the E+1 from the programmer and insert it into the socket on the
rear of the validator. Ensure that the legs are correctly seated in the
socket, the orientation is correct and that the bottom of the PCB rests on
the loom connector as shown. Replace the validator in the stand for
testing.
Switch 2 set to OFF.
Switch 1 to ON for Segment 1.
Legs firmly seated in socket.
Correct orientation and rear of PCB

seated on connector.
?? Click on Validator Test
?? Drop each type of old coin through the validator and confirm that the
appropriate lamp lights.
?? Set Switch 1 to OFF and confirm acceptance of the Euro coins and any
known slugs are rejected. Set Switch 1 back to ON.
?? If one or more coin limits need to be widened to improve acceptance or
narrowed to reject a slug, click on Back to Main Menu to return to the
Prom Limits screen. Adjust limits as required and reprogram the E+1 as
before then retest. Further adjustments and retests can be carried out on
the mechanism without consuming another credit provided you do not go
back to the Measurement Window.
?? Click on Back to Main Menu and Back to Measurement Window ready
for the next validator.
?? Remove the validator from the stand, disconnect loom, and affix a suitable
label to the front giving details of the new coins accepted.
Coin Controls/NRI – example G13-6000

Note: The basic Programming routine is the same for both for Coin Controls
and NRI mechanisms.
?? Click on NRI TIPS!
** If a new type of mechanism if to be
?? Click on Program Mech programmed, save the original data using
“Save to File” so it can be restored if
required. See Additional Features.
** To confirm the mech is ready to
program select the Mech Type and click
on Memory Utilities. If the memory reads
correctly the mech is communicating
correctly.
HELP:
If “No response from programmer box”
or “No validator detected” appears check
the Fault-Finding Table in the Appendix.
?? Click on Run Coinset File
?? Open the appropriate coinset file (In this example MK10–G13 6000 which
adds up to 6 new coins in Channels 1 to 6 retaining the existing output
mapping.) We will add just three new coins - 50c, 1Euro & 2Euro.
NOTES:
Coin Channel:
?? Once the Coinset File has been opened the following typeCoin
of message
1 goes into will
channel
appear. The Coin Type may be generic such as 1 or specific 1. Coin
such as 5c.2
into channel 2 etc.
?? Click on OK to start the coin drop Number of Coins
Remaining: Will
decrease to zero as
coins requested are
dropped through
the validator.
Mech Type : The
family of mechs
suitable for use with
this Coinset File.
?? Drop the coins through the validator until the Number of Coins
Remaining field drops to zero and the following message appears.
NOTE:
*The readings for each measurement
parameter are displayed for each coin as it
is dropped along with various statistics.
*The upper and lower limit for each
parameter is calculated and updated as
each coin drops.
?? Click on OK to repeat the process for the rest of the coins which require
data gathering (2 and 3) or Cancel to Skip and pass on to the next.
?? Click on OK when the message “Data Gathering Complete” appears.
?? The contents of the

EEPROM are read to
pick up any required
data.
NOTE:
If any
overlapping
limits are
shown (Yellow
highlights)
adjust the
limits to
remove the
overlaps or
the coins will
be rejected
after
programming.
?? The estimated acceptance of each coin is displayed. If required adjust the

limits by overtyping then click on Change Limits to see the revised
Acceptance. Adjust if necessary. Clicking on Restore Limits will restore the
limits to their original values.
?? Click on Program EEPROM
NOTE:
The number of credits
which will be deducted to
complete the programming
is displayed.
?? Click on OK to continue.
?? Click on OK to complete.
?? Click on Validator Test
?? Drop each type of Euro coin through the validator and confirm that the
appropriate lamp lights to confirm acceptance of the Euro coins. If slugs
are suspected drop these and confirm that they are rejected.
?? If one or more coin limits need to be widened to improve acceptance or
narrowed to reject a slug, click on Back to Main Menu to return to the
Prom Limits screen. Adjust limits as required by overtyping and clicking
on Change Limits, reprogram the EEPROM as before then retest. Further
adjustments and retests can be carried out on the mechanism without
consuming another credit provided you do not go back to the
Measurement Window.
?? Click on Back to Main Menu, Back to Measurement Window and Back
to Main Menu ready for the next mechanism.
?? Remove the mechanism from the stand, disconnect loom, and affix a
suitable label to the front giving details of the new coins accepted.
Wizards
Wizards are special routines to carry out specific tasks without going through a
complete programming sequence. They do not require the use of a Coinset
File. Each use of a Wizard consumes a credit. There are three wizards
included in this version.
Access the Wizards from the Main Menu
?? Select make of mech to be used eg. Mars (NRI/CC are similar)
?? Click on Program Mech
?? Click on Wizards
Add/Replace Coin
Used to gather data on a new coin and add it into a spare coin channel on an
existing coinset held in a PROM/ E+1. Instead of adding it into a spare
channel, it can also replace an existing coin.
?? Select Mech Type
?? Select the PROM segment and Coin Channel to position the new coin.
?? Click on Add/Replace Coin
?? Click on OK and drop 20 coins

?? Click on OK and the follow the screen prompts to read the old PROM.
?? The PROM limits screen will appear with the limits from the old PROM and
those generated by the coins dropped. ( 2 Standard Deviations +/-2).
Adjust as required and then Program New PROM and Validator Test as
per the Basic Programming Routine.
Slug Fix
A Slug is an item which a validator incorrectly assumes is a particular genuine
coin. eg machined blanks, foreign coins, two coins glued together. The
validator can usually be recalibrated to discriminate between the real coin and
slug by running the slug through the Programmer and adjusting the existing
limits for the coin to exclude the slug. Slug Fix can be used at any time to carry
out this task.
?? The routine for this is the same as per Add/Replace a Coin above except
that in addition the programme asks for a Slug Drop. ie drop 20 of the slug
through the validator as if it were a coin. Adjust the limits as required to
remove the yellow overlap between coin and slug and confirm rejection of
the slug using validator test.
Edit Limits
This routine reads the data from an existing PROM or E+1 and displays it on
the PROM limits screen. The limits can be manually adjusted. (For example:
Opening up to improve acceptance or shutting to zero to remove a coin).
The routine for this is the same as per Add/Replace a Coin above except that
no coin drop is required.
Discriminating against a known slug

If a known slug exists it can be removed while programming for new coins
using a suitable Coinset file or at a later date using the Slug Fix wizard.
Using a Coinset file:

Select a Coinset file for the mech to be programmed which has the letter “S” in
the title sequence. Eg “MK04S ME111”
When requested drop through the quantity shown of the slug to be removed.
At the Limits screen the slug and the coin affected will be highlighted in yellow.
Adjust one or more of the Limits of the coin to remove the overlap and click on
Change Limits. The estimated acceptance of the coin and reject %age of the
slug will be displayed. If suitable proceed with programming, if not retry using a
different adjustment.
Notes: In a few cases, due to the nature of the mechanism and slug, it may
prove difficult to completely remove the slug while still retaining adequate coin
acceptance. In this case contact your Programmer supplier for advice.
Using a Slug Fix Wizard:

See Basic Reprogramming Routines section above.
Additional Features
Mars
PROM utilities
From the Main Menu or the Prom Limits screen the option of PROM Utilities
can be selected.
?? Click on PROM Utilities
Read PROM
?? Insert the PROM or E+1 into the socket on the Programmer.
?? Click on Read PROM
NOTE:
If entering
from the
PROM Limits
screen, this
box will
contain the
limits/data for
the validator
being
programmed.
?? The contents of the PROM will be displayed in the left box.

?? Select Limits or Data from the Display box.
?? In the Limits display the upper and lower limit for each parameter of each
coin are shown.
?? In the Data display the data is displayed in HEX format.
?? Click on Close Window to return to previous screen.
Flier limits
Occasionally, spurious readings are generated by the a sensor
as a coin passes. This can be due to the coin bouncing, following another coin
too closely etc. and is termed a “Flier”. If Fliers occur during programming an
error message is shown and further coin drops may be requested to complete
the Data Gather. Click on OK and drop the coins if required.
Coin Controls/NRI
EEPROM/Memory Utilities
?? From the Main Menu select the make of mechanism
?? Click on EEPROM Utilities (Coin Controls) or Memory Utilities (NRI)
?? The Limits contained in the Memory are displayed.
Display of other information (eg parameters, mapping, etc):

Depending on which type of mech is being used other information may be
available. See individual mechanism section for details.
Save to File:
Click on Save to File to save the EEPROM/Memory data to a file. Used as
part of the Cloning Routine and to save the data from a mechanism in case it
needs to be returned to it’s original settings.
Program from File:

Click on Program from File to program the EEPROM from a previously saved
file. Used as part of the Cloning Routine and to return a mechanism to it’s
original data if stored.
Cloning Routines:
Cloning of additional parameter settings:
Note: All coin mechanisms
When converting to different coinage, additional must be individually
parameters in some mechanisms (eg G13, G18, reprogrammed for coins as
G10, C120, C220B, C335, C435, C450) may part of the Cloning Routine.
require changing. The facility to change these as
part of the Programming is included in some cases but not all. Also, a
mechanism programmed with an incorrect coinset may need to be returned to
it’s original configuration. Cloning has been introduced in software version
V1.2C onwards to allow this. Cloning takes this data from a sample
mechanism that already has the required settings and puts it into the
mechanisms being programmed.
NRI only - method

?? Connect sample mechanism of same type to be programmed with
known correct additional parameter settings. Using Memory Utilities, Save
EEPROM to file.
?? Connect mech to be programmed.
?? Programme using Coinset file which does not change other parameters
(or Wizard) as normal but do not program the EEPROM.
?? Before leaving the PROM Limits screen go to EEPROM utilities and
Program From File using saved file above. Close window.
?? Click on Restore Limits and adjust limits if necessary..
?? Program EEPROM and Validator Test in usual manner.
Notes: Only one credit will be deducted per mech programmed.
The saved file from the sample mech can be used for any other mechs of the
same type requiring the same configuration.
Coin Controls only - method:

?? Connect sample mechanism of same type to be programmed with
known correct additional parameter settings. Using Memory Utilities, Save
EEPROM to File.
?? Connect mech to be programmed. From the Main Menu go to
EEPROM Utilities, select Program from File and program using the saved
file above. This will deduct one credit.
?? Go back to Main Menu and program in the usual manner using a
Coinset file which does not change the additional parameter settings. This
will deduct another credit.
Reprogramming – by coin mech type

Mars
MS1000 family: See Appendix for listing of individual mechs supported.
Programme as basic MARS routine but note the following:
?? Connect loom E1 MS1000 (Ribbon) from Socket 4 of programmer to
bottom of validator.
Switch 2 set to OFF.
Switch 1 to ON for Segment 1.
E+1 usage:
?? Use E+1V (Blue) fitted as
Legs firmly seated in socket.
shown.
?? MS1900 has two PROMs – fit Correct orientation and rear of PCB
seated on connector.
E+1 to lower one. Remove
upper PROM when switching
to Segment 2 coin set to stop acceptance of old coins G, H & I.
?? If more than 6 coins are required in one coinset program coins A to F into
Segment 1 of the E+1V and Coins G to I into Segment 2 of a PROM.
Insert the E+1V into the lower socket and the PROM into the upper socket.
Selecting Segments:
?? If all coins are rejected on Validator Test the validator may have been
modified to use Segment 2. Check the areas around the PROM socket for
signs of a cut or drilled out track. If found repair the cut to return the
validator to Segment 1.
?? Switch from Segment 1 to Segment 2 using SW1 on the E+1.
Fitting to Changegiver:
?? Consult the manufacturer’s documentation for details of mapping coins to
change tubes etc.
?? Mektek coin tube sleeves to convert change tubes to new coins are
available from your Programmer supplier.
MS1400 Klix

?? Connect loom E7 MS1400 from Socket 4 of programmer to rear of
validator as shown.
E+1 usage:
?? Use E+1K (Red) fitted as shown.
Selecting Segments:
?? If all coins are rejected on Validator Test the validator may have been
modified to use Segment 2. Check the areas around the PROM socket for
signs of a cut or drilled out track. If found repair the cut to return the
validator to Segment 1. If no cuts are found reprogram with the coins in
Segment 2 and SW1 set to OFF.
?? Switch from Segment 1 to Segment 2 using SW1 on the E+1.
Changegiver compatibility:
?? Consult Mektek Europe for advice & assistance before programming.
ME111 family: See Appendix for listing of individual mechs supported.

?? Connect loom E2 from Socket 4 of

Programmer to 20 -way connector
E+1 usage:
?? Most of these mechs will have a number of sets of pins – see below -
above the PROM socket. Before fitting E+1A (Green) clip off the tops of
these pins to the level of the links to allow E+1 to seat onto PROM socket.
?? The mech may have been set to Segment 2 or 1. If only one set of coins is
to be programmed use a Coinset that puts the new coins into Segment 2.
Program the E+1A and set Switch 1 to OFF. This will allow the new coins
to be accepted regardless of which Segment the mech has been set to.
Selecting Segments:
?? To return the mech to Segment 1 in order to use a

A B C D E PROM see below.
??
ME115TS – link on “C” but not on “E”
ME111/ME126 - no link on “C” or “E”
Leave other links unaltered.
MS111B1 – there are no sets of pins on this

mech. Sometimes the mech was modified to
read Segment 2 only. To select Segment 1
solder a link between pins
14 & 15 on the rear of the PROM socket.
Validator test:
If all coins are rejected after programming:
E+1A - see section in E+1 usage above.
PROM – if the links above have been set correctly it is likely that the
mechanism has been incorrectly modified. In this case reprogram using a
Coinset File that puts the coins into Segment 2.
MS111 family: See Appendix for listing of individual mechs supported.

Programme as basic MARS routine and ME111 above but note the following:
?? Coinset files as per ME111
?? Connect loom E8 from Socket 4 on

Programmer to 16 -way connector
Bipolar PROM usage:

To use a PROM first establish which Segment is set.
?? Before programming run Validator Test to verify
existing coin acceptance. Examine the PROM to see
if Leg 15 has been withdrawn or removed – if so the
mech is set to Segment 1. If not withdrawn or
removed, remove PROM, bend up leg 15 and refit.
Retry Validator Test and if the coins are rejected the
mech is also set to Segment 1. Proceed with
Programming in normal manner.
?? If the coins are still accepted after withdrawing Leg 15 the mech has been
modified to read Segment 2. In this case use a Coinset File that adds the
coins to Segment 2 and withdraw Leg 15 of PROM before fitting.
E+1 usage:
?? On some MS100 variants there may be insufficient clearance for an E+1A
to be fitted. In this case use a bipolar PROM.
?? See section in E+1 usage for the ME111.
Selecting segments:
?? E+1 – use SW1 to switch from Segment 1 to Segment 2.
?? PROM – withdraw Leg 15 to switch to Segment 2.

Duplicate segments (Mars):
When adding a single coinset to a Mars mechanism we recommend putting
the same limits data into both segments of the E+1/PROM so that it works
regardless of the segment that the mech is set to. At the Capture
Measurements screen, before selecting Run Coinset, tick the box marked
Duplicate Segments.
ME181/ME112
?? Programme as per basic Mars routine but see below.
?? Obtain a Coinset File with the required Coin Values from your Programmer
supplier.
Looms required:
ME181:
E4 : ME181 2/2 (Wire) - socket 4 to side of mechanism
E3 : ME181 1/2 (Ribbon) – socket 3 to flying lead from mechanism
ME112:
E4 : ME181 2/2 (Wire) - socket 4 to side of mechanism
E3 : ME181 1/2 (Ribbon) – socket 3 to end of E31
E31: ME112 2/3 (Ribbon) – between the end of E3 & bottom of mechanism
E+1 usage
?? Use only E+1A (Green) or 2k PROM. Two segments are programmed
with the coinsets and the other two segments have the values for the coins
in these segments. Follow the on-screen prompts when programming.
Selecting segments
?? Set switch 1 (SW1) on the validator to
OFF to select Segment 1 and ON to
select Segment 2.
Coin Controls
C120 family: See Appendix for listing of individual mechs supported.

Programme as basic Coin Controls routine but note the following:
?? CAUTION: Different connections are used for Acceptors and
Totalisers. Connecting the E10 Ribbon Cable from an Acceptor to the
G13 Tote Only socket on the Programmer can damage the
Programmer and/or mechanism.
?? Looms required:
E10 G13/C120 from socket 1 to rear of validator as shown
E11 C120/C435 from socket 2 to rear of validator as shown.
?? Any overlapping limits or limit greater than 254 will cause coins to be
rejected.
Old & new type mechanism identification:

Remove the rear cover. Old type C120s usually
have the word “Jaguar” in the top right hand
corner of the PCB.
Output Mapping:
?? The ouput mapping – which Channel is
output on which pin – can be changed by use
of a suitable Coinset File. As the mapping
data is stored differently in the old and new
types it is important that the Coinset File
chosen relates to the correct type if the mapping is to be changed.
?? If no coins are accepted on Validator Test after programming or when
fitted to the host machine it is likely that an unsuitable Coinset File has
been used.
Display of other information:

?? Read EEPROM and from Display select Other Information
The mapping is displayed. The settings are defined in the Coinset File and
cannot be altered during programming.
Bank selection:
?? Up to 12 coins can be accepted. They are split into two Banks - coins 1 to
6 in Bank 1 and 7 to 12 in Bank 2.
?? Switch from Bank 1 to Bank 2 using the 4-way switch on the PCB.
?? Switch 1 to ON and Switch 2 to OFF to select Bank 1. Reverse for Bank 2.
Coin Inhibit:
?? Individual coins in the active Bank can be inhibited using the 6-way
switch on the PCB.
?? Switch 1 to ON to inhibit Coin Channel 1, switch 2 to ON to inhibit Coin
Channel 2 etc.
C220B:
?? Looms required;
E12 C220B/335 from socket 2 to validator
E17 C220B from socket 3 to validator
Coin Accept Mode:

?? In normal mode coins 1 to 4 are output on pins 1 to 4 and coins 5 to 8 (If
enabled) are also output on pins 1 to 4. To use the 8-coin mode the host
machine must tie the SELECT line (Pin 6) on the interface connector to 0V
(Pin 10). In the 8-coin mode all 8 coins are accepted.
Coin Inhibits:
?? Coins are inhibited by the host machine via the interface connector rather
than via switches on the mechanism.
Acceptance faults when fitted to host machines:

?? If coins are not being accepted on some host machines ensure that the
Programmer software used is V1.2C or later.
?? If problems still occur, use the Cloning Routine described in a later
chapter.
rejected.
C335:
?? Looms required;
E12 C220B/335 from socket 2 to validator
E16 C335 from socket 3 to validator
Coin Accept Mode:

?? In parallel mode there are 5 outputs for up to 8 coins with coins 6,7 & 8
paired with coins 1,2 & 3 respectively. In binary mode up to 8 coins can be
accepted.
.
Validator test:
?? Select Output Mode of either Single or Binary.
?? In binary display as well as the coins accepted in binary mode the credit
code in single output is shown by lights A1 to A5.
Coin Inhibits:
?? Coins are inhibited by the host machine via the interface connector rather
than via switches on the mechanism.
Acceptance faults when fitted to host machines or validator test:

?? If problems occur, use the Cloning Routine described in a later chapter.
rejected.
C435 & C435A:

?? Looms required;
E11 C120/C435 from socket 2 to validator
?? Overlapping limits must be removed or coins will be rejected.
Binary coding & Coin Routing etc:
?? The binary coding – which Channel is output on which pin – can be
changed or left unchanged by use of a suitable Coinset File. Usually the
output for the C435 is straight binary and for the C435A is the UK BACTA
standard but these may have been changed. It is vital that the correct
binary coding is used for a particular application.
?? Generally, we recommend strongly that a Coinset File which leaves the
coding, routing etc unchanged is used. See the Coinset File Description
section in the Appendix.
?? Routing is normally set to the Plug default – if EEPROM routing is required
consult your Programmer supplier for a new Coinset File.

?? Read EEPROM and from Display select Other Information.
C435 BACTA C435 Binary
?? The C435 Ancillary Settings of Coin Routing and Binary Output code
for each coin are shown. To change the settings manually overtype and
then click on Programme Routing to programme the memory. This will
use a credit.
Piezo sensor:
Due to problems experienced by our customers with the reliable working of the
Piezo sensor (Parameter 5) it has been disabled in the generic Coinset Files. If
this sensor is required for specific coins, please consult your Programmer
supplier for a new Coinset File.
Coins accepted:
?? Up to 16 coins in 2 banks of 8 can be accepted in binary output and up to
5 coins in dedicated output.
?? Channels 5 & 13 are often set to a Token. To replace a Token with a coin
during programming set the Rotary Switch to F to start and return it to C
after programming.
Coin Inhibit:
?? Coins are usually inhibited by the host machine via the interface
connector and Bank Select switch on the mechanism.

?? If some types of coin are rejected check and remove any overlapping
limits.
?? If all coins are rejected it is likely that an unsuitable Coinset File has been
used. Reprogram using a Coinset File that changes the binary coding etc
to the standard required.
rejected.
?? If problems persist, use the Cloning Routine described in a later chapter.
C450
?? Looms required:
rejected.
Routing:
?? The coin routing is usually set to BDTA standard but it may have been
changed. See below to check.
?? Generally it is advisable to a Coinset File which leaves the routing
unchanged. See the Coinset File Description section in the Appendix.

?? Read EEPROM and from Display select Other Information.
The routing for each coin is displayed.
Function of the banks of switches on rear of mechanism;

Switch Bank A:
?? Coin Inhibits
Individual coins in six coin mode or pairs of coins in 12 coin mode can be
inhibited using the 6-way switch.
Switch 1 UP to inhibit Coin Channels 1 & 7, switch 2 UP to inhibit Coin
Channels 2 & 8 etc.
Switch Bank C:
?? Coin mode:
Switch 4 DOWN selects six coin ouput and UP selects 12 coin binary output.
?? Bank select:
Up to 12 coins can be accepted in two banks of 6 coins
Switch 5 DOWN enables coins 1 to 6.
Switch 6 DOWN enables coins 7 to 12.
Validator Test:
?? Similar to C335 above but Binary display is not available.

?? If some types of coin are rejected check and remove any overlapping
limits.
?? If coins exit from the wrong router path it is likely that an unsuitable
Coinset File has been used. Reprogram using a Coinset File that changes
the routing to the standard required.
?? If problems persist, use the Cloning Routine described in a previous
section.
C220 & Sentinel:

See Appendix for listing of individual mechs supported
?? Looms required;
E17 C220/Sentinel from socket 3 to validator
E25 C220/Sentinel from socket 2 to validator
Coin accepted:
?? In normal mode coins 1 to 4 are output on pins 1 to 4 and coins 5 to 8 (If
enabled) are also output on pins 1 to 4.
Coin Inhibit:
?? Coins are usually inhibited by the host machine via the interface
connector.
Acceptance faults when fitted to host machines:

?? Reprogram using a Coinset File with larger windows. See the Coinset File
Description section in the Appendix.
rejected.
?? If problems still occur, use the Cloning Routine described in a later
chapter.
NRI:
G13 family: See Appendix for listing of individual mechs supported.
Programme as basic NRI/Coin Controls routine but note the following:
?? CAUTION: Different connections used for Acceptors and Totalisers.
Connecting the E10 Ribbon Cable from an Acceptor to the G13 Tote
socket on the Programmer can damage the Programmer and/or
mechanism.
?? Coinset Files with individual coin values are required for Totaliser variants.
Consult your Programmer supplier for a Coinset File specific to your
needs.
?? Looms required:
E10 G13/C120 (Ribbon) from socket 1 to validator as shown
E14 G13 from socket 2 to validator as shown.
?? Validator Test is not available for Totaliser variants.
Mechanism type identification:

Acceptors:
Type G13-0000 – one loom connection visible though back cover.
Type G13-6000 – both loom connections visible through back cover.
G13-1000 is a front plate version of G13-0000
G13-7000 is a front plate version of G13-6000
Totalisers:
A “2”, “3” or “4” in the red position indicates a Totaliser variant.
G13-0000
G13-60000
Measuring Parameters:
?? The G13-6000 variants have selectable measuring parameters which
are defined in the Coinset File.
Output & Inhibit Mapping: (G13-6000 series only)

?? The ouput & inhibit mapping – which Channel is output on which pin and
which Channel is inhibited by which switch – can be changed by use of a
suitable Coinset File.
?? If no coins are accepted on Validator Test after programming or when
fitted to the host machine it is likely that an unsuitable Coinset File has
been used.
Coins accepted:
?? Up to 12 coins can be accepted in the G13-6000 family and up to 6
coins in the G13-0000 family
Coin Inhibit:
Individual coins can be inhibited using the 6-way switch(es) on the PCB.
?? G13-0000 has one bank of switches. Switch 1 UP to inhibit Channel 1,
switch 2 UP to inhibit Channel 2 etc.
?? G13-6000 has 2 banks of switches. On Bank 1, Switch 1 UP to inhibit
Channel 1, switch 2 UP to inhibit Channel 2 etc. On Bank 2, Switch 1 UP to
inhibit Channel 7, switch 2 UP to inhibit Channel 8 etc.
?? Totaliser: Refer to NRI Data Sheets.

?? Read EEPROM and from Display select Parameter Map
The parameters used for each coin are displayed. The parameters used
are defined in the Coinset File and cannot be altered during programming.
?? From Display select Other Information

The output mapping and inhibit mapping
for each coin are displayed.
The “Values” column refers to Totalisers
only. These are defined in the Coinset
File and cannot be altered during
programming.
G10 family: See Appendix for listing of individual mechs supported.

Programme as basic NRI/Coin Controls routine but note the following:
?? The Coinset File to be used will contain coin values, tube routing etc and
therefore no generic coinsets are available. Consult your Programmer
supplier for a Coinset File specific to your needs.
?? Loom E15 G10 fitted from socket 4 to validator
Mechanism variants:
?? There are various variants of the G10. Most of these are similar to the
4000 or 4000/5 and are supported by the programmer. If in doubt select
NRI and Mech Type in the Main Menu and then EEPROM Utilities. If the
correct type is selected the contents of the Memory will be displayed.
?? Should you have an unsupported variant, contact your Programmer
supplier to see if it can be added.
?? Validator Test – is only supported on some of the variants.
G40 family: See appendix for listing of individual mechs supported. Check
the loom cross-reference as there are two main types which have different
connections. Program as basic NRI routine but note the following:
?? Coinset files with individual coin values are required. Consult your
Programmer supplier for a Coinset file specific to your needs.
?? Additional looms used – may require removal of rear cover
E13 (socket 3) & E26 (socket 2) for G40-x3xx & G40-x4xx
E14 (socket 2) & E20 (socket 5) for G40-x0xx, G40-x5xx & G40-x6xx
?? Select the exact variant on Validator Test screen
Mechanism variant identification:

?? The second digit in the model number denotes the main variant.
eg G40-x4xx There could be a variety of numbers in the “x” positions
dependent on coin entry exit etc. but it is programmed as a G40-x4xx.
Measuring Parameters:
?? Selectable measuring parameters are defined in the Coinset file.
Output mapping, inhibit mapping and sorter settings:
?? The output and inhibit mapping – which channel is assigned to each of
the 6 output lines and which channel is inhibited by which switch – along
with the coin routings if a sorter is fitted are set by the Coinset file.
Multiple output pulses on one output line:

?? Multi-pulsing – eg one pulse for 50cent & 2 pulses for 1Euro – is
supported by the mechanism and is defined in the Coinset File
Coins accepted:
?? Up to 12 coins can be accepted but there are 6 output lines.
Coin inhibit:
Individual coin channels can be inhibited using the two switches on the PCB.
?? On the upper bank, Switch 1 ON to inhibit Channel 1, Switch 2 ON to
inhibit Channel 2 etc.
?? On the lower bank, switch 1 ON to inhibit Channel 7, Switch 2 ON to
inhibit Channel 8 etc.
Validator Test:
?? Before passing coins through the mech select the appropriate variant
from the drop-down box on Validator Test screen.
?? Some mechanism variants support Binary Output and this can be
selected from the Validator Test screen. See Coin Controls C335 section
for details.

?? Read Memory and from Display select Parameter Map. The
parameters used for each coin channel are displayed. The parameters
used are defined in the Coinset
File and cannot be altered
during programming.
?? From Display select Other
Information. The output
mapping in Hex, inhibit
mapping, coin value, pulses
and sorter routing is displayed
for each coin. These values are
defined in the Coinset File and
cannot be altered during
programming.
Appendix
Keeping Up to Date:
Obtaining Coinset Files:

?? Generic coinset files covering most applications can be downloaded
from the Coinset Download page on our website
www.mektekinternational.com.
?? Specific Coinset files for a particular application will be provided on
request. Please discuss your requirement in detail with your Programmer
supplier.
Updated operating software:

New features, improvements and support of new types of coin mechanism are
regularly being added to the Programmer operating system in response to
user feedback. Check our website www.mektekinternational.com regularly and
download the latest updates free-of-charge.
Technical Help & Fault Reporting

If you require help or advice relating to the operation of Mektek equipment:
?? Check out the Programming Help page on our website
www.mektekinternational.com
?? Contact your local Mektek Programmer supplier directly or Mektek
International Ltd. via our website Contact Page.
?? Check out the technical data available on the manufacturers’ websites.
Mars – www.meiglobal.com
NRI - www.nri.de
Money Controls (Coin Controls) – www.moneycontrols.com

Duplicate segments (Mars):
When adding a single coinset to a Mars mechanism we recommend putting
the same limits data into both segments of the E+1/PROM so that it works
regardless of the segment that the mech is set to. At the Capture
Measurements screen, before selecting Run Coinset, tick the box marked
Duplicate Segments.
Language options: The PcPro software is now available in various languages.

A the Main Menu select Change Config then select language required and
Save Config. Restart the Programmer software to implement.
Tables:
E+1 Switch settings

When used as 1k select the active coin set When used as 2k select the active coin
segment via the validator links/switches
Switch ON OFF OFF ON
1 Seg 1 active Seg 2 active Not to be used Normal setting
When used as 1k or 2k enables erasing and programming

Switch ON OFF
2 Erase and program
1 2 enabled E+1 is Read-only and cannot be altered
WARNING: Data will be erased if Switch 2
left ON when verified or fitted to a validator
Fault-finding:
Description Cause/Action
No response from programmer Comms fault - switch box off/on
box Disconnect mech then if OK = faulty mech
Reboot system
Check PC to box loom
Operating system conflict for selected COM port
No validator detected Check box to mech loom
Comms fault - switch box off/on
Faulty validator – check using Memory/EEPROM utilities if
Coin Controls/NRI.
Coins not recognised when Wrong coinset file used
dropped during programming Wrong looms used or looms not fitted
Mechanism not supported by Operating software version used
– download latest software from our website.
Data device fails verify PROM - check orientation in socket. Notch adjacent to red
spot and opposite end to lever
E+1 - check switch settings and retry Program PROM.
Bipolar PROM – check 16.0 or 16.5v power supply used
Mech fails validator test Mars: Check PROM/E+1 inserted correctly
Check switch settings on E+1
Check links on mechanism set correctly for Segment
programmed – ME111 family.
Mech incorrectly fitted to stand when programmed or tested -
reprogram and retest.
Coin Controls/NRI: Check all looms fitted as specified.
Incorrect Coinset File used when programmed - confirm mech
type, reprogram and retest.
Check and remove overlapping limits on C435/C435A
Maximum limit value of 254 exceeded.
Mech passes validator test but C435/C435A – coinset file used which changed mapping etc.
rejects coins on host machine. to inappropriate standard. Reprogram using correct coinset file
or use Cloning Routine.
C220B – reprogram with version 1.2C or later operating
software.
Coin Controls/NRI unable to Check looms
read memory Check correct mech type selected
Check revision level of interface panel on rear of Programmer
(Ask Programmer supplier for details)
Faulty mechanism
Mechanism type not supported
DESCRIPTION OF GENERIC COINSET FILES

NOTE: If a coins or slug is not required select “Skip” when programming to pass onto the next
channel. See the Operator’s Manual for details.
MARS
MS1000 family:
MS1000 coinset files work on most of the MS1000 family including MS1600, MS1604, MS1610,
MS1614, MS1900, MS1904, MS1910, ME1099, ME1100,
Mech variants: If the mechanism is similar in shape to the above and the loom E1 fits the 20-way
ribbon connector on the coin mechanism then use the MS1000 Coinset Files.
MK01S MS1000 add up to 6 new coins to segment 1
MK01AS MS1000 Add up to 12 new coins
MK02S MS1000 add up to 6 new coins to segment 2
MK03S MS1000 add up to 6 new coins to segment 2, copy old segment 1 to new segment 1
MK03AS MS1000 Copy old segment 2 to segment 1 Add up to 6 new coins to segment 2
ME111 family:
ME111 coinset files work on most of the MS100 family including ME111, ME115, ME115TS,
MS111B1, MS111, ME126, ME129, & MS130B1 (For the MS150 consult your Programmer
supplier).
Mech variants: If loom E2 or E8 fits the lower left-hand connector on the coin mechanism then use
ME111 Coinset Files.
MK04S ME111 add up to 6 new coins to segment 1
MK04AS ME111 Add up to 12 new coins
MK05S ME111 add up to 6 new coins to segment 2
MK06S ME111 add up to 6 new coins to segment 2, copy old segment 1 to new segment 1
MK06AS ME111 Copy old segment 2 to segment 1 Add up to 6 new coins to segment 2
NRI
G13 Family:
The G13 0000 and G13 6000 series require different Coinset Files.
The G13 7xxxx is a front plate version.
Notes:
- For Totaliser variants the value of each coin is defined into the mechanism during programming.
Contact your Programmer supplier for specific coinsets.
- G13 6000 series has selectable measuring parameters which are defined for each coin being
programmed in the Coinset File. For this reason mechanisms using the Generic Coinset Files
below should have their discrimination and acceptance thoroughly tested after programming to
ensure that performance levels are acceptable.
MK10S G13-6000 (Acceptor Only) Add up to 6 new coins 1-6, outputs/inhibits 1-6 respectively
MK10AS G13 6000 (Acceptor Only) Add up to 12 new coins
MK10BS G13 6000 (Acceptor Only) Copy coins 1-6 to 1-6 Add up to 6 new coins to 7-12
MK11S G13-0000 (Acceptor Only) Add up to 6 new coins to channels 1-6
MK11AS G13 0000 (Acceptor Only) Copy coins 1-3 to 1-3 Add up to 3 new coins 4-6
G18: Acceptor only – for Totaliser variants contact your Programmer supplier.
MK14S G18-3000 (Acceptor Only) Add up to 6 new coins (Output/inhibit 1-6)
MK14AS G18-3000 (Acceptor Only) Add up to 12 new coins (output/inhibit 1-6 & 1-6)
MK14BS G18-3000 (Acceptor Only) Copy coins 1-6 to 1-6 Add up to 6 new coins 7-12
(Ouput/inhibit 1-6 & 1-6)
G10: These coinsets contain individual coin values for each coin channel and change tube routing.
For other values etc consult your Programmer supplier. For G10-4000/5/6/9 consult your
Programmer supplier.
MK15S G10-4000 Adds coins 5c/10c/20c/50c/1euro/2euro to channels 1-6 & 5c/10c/50c to coin
tubes left/middle/right
Coin Controls
C220B:
MK20S C220B Add up to 4 new coins to channels 1-4
MK20AS C220B Add up to 8 new coins
MK20BS C220B Copy old coins 1-4 to 1-4 Add up to 4 new coins 5-8
C335:
MK21S C335 add up to 5 new coins to channels 1-5
MK21AS C335 Add up to 8 new coins (Coins 6,7,& 8 twinned with coins 1,2 & 3 respectively)
C435 family:
The routing of coins through the in-built sorter in the mechanism can be defined in the memory of
the mech or via an external header routing plug. Generic Coinset files use the routing plug with
default route "A". The Piezo sensor is disabled in the Generic Coinset files for all coins.
The use of MK22CS C435, which does not change the binary Coding or routing, is strongly
recommended for both C435 and C435A. CAUTION:Using MK22B, MK22C or MK29 changes
the Binary Coding output configuration.
C435:
MK22CS C435 Add up to 8 new coins (Binary Coding and Routing unchanged, Piezo disabled)
MK22BS C435 Add up to 8 new coins (Binary Coding 1-8, Plug Routing, Piezo disabled) –
Caution: changes Binary Outputs
C435A:
MK22CS C435 (Also used for C435A) Add up to 8 new coins (Binary coding and Routing
unchanged, Piezo disabled)
MK22AS C435A Add up to 8 new coins (BACTA Binary Coding, Plug routing, Piezo disabled) -
Caution: changes Binary Outputs
MK29S C435A Add up to 14 new coins – not coins 5 & 13 (BACTA Binary Coding, Plug routing,
Piezo disabled) - Caution: changes Binary Outputs
C450 family:
MK24S C450 Add up to 6 new coins (Routing unchanged)
MK24AS C450 Add up to 12 new coins (Routing BDTA)
MK24BS C450 Copy old coins 1-6 to 1-6 Add up to 6 new coins 7-12 (Routing BDTA)
MK24CS C450/5 Add up to 12 new coins (Routing BCADAABCADAA)
MK24DS C450 Add up to 12 new coins (Routing unchanged)
C120 family:
The C120, C122 and C123 use the C120 Coinset Files.
C120
MK23S C120 New/Old Type Add up to up to 6 new coins to channels 1-6 (Mapping unchanged)
MK23AS C120 New Type Add up to 12 new coins (Mapped 1-6 & 1-6)
MK23BS C120 New Type Copy old coins 1-6 to 1-6 Add up to 6 coins 7-12 (Mapped 1-6 & 1-6)
MK23JAS C120Jaguar Type Add up to 12 new coins (Mapped 1-6 & 1-6)
MK23JBS C120Jaguar Type Copy old coins 1-6 to 1-6 Add up to 6 coins 7-12 (Mapped 1-6 & 1-6)
C220, C220A, Sentinel:
MK25S Sentinel Add up to 4 new coins (Routing unchanged)
MK25AS Sentinel Add up to 8 new coins (Routing unchanged)
MK25BS Sentinel Copy old coins 1-4 to 1-4 Add up to new coins 5-8 (Routing unchanged)
Mechanisms Supported by this Programmer Model

Mechanism Coinset file family Loom(s) Comments
Mars Mechanisms
ME111, ME115, ME115TS, ME111 E2 20 pin connector
ME126, ME129, MS111B1
MS111, MS125, MS126, MS127 ME111 E8 16 pin connector. Remove
separator
MS110 ME111 E17 & E32 Edge connector
MS1600, MS1900, ME1099 MS1000 E1
MS1400 MS1400 E7 Klix machine
MS130B1, MS180 ME111 E5 & E6
ME181, ME112 ME181 special E3 & E4 & E31 Connect E31 to E3 if no flying
ribbon cable on mechanism
MS150 ME181 special E9
MS15, MS25 ME111 E30
MS140, MS160 Special looms required Contact Mektek
MS10 ME111 E34
MS12 ME111 E33
Coin Controls Mechanisms

Mechanism Coinset file family Loom(s) Comments
C120 C120 new type E10 & E11 See rear of PCB for identity
C120 “Jaguar”
C220/C220A, Sentinel Sentinel E17 & E25
C220B C220B E12 & E13
C335/C335S C335 E12 & E16
C435, C435A, C420 C435, C435A. Ensure correct E11 & E13
binary coding option selected
C450, C455 C450 E20 & E23
NRI Mechanisms
Mechanism Coinset family Loom(s) Comments
G13-0000, G13-1000 acceptor G13-0000 E10 & E14 1x6 way DiL switch only
G13-6000, G13-7000 acceptor G13-6000 E10 & E14 1x6 way DiL & 1x6 or 1x8 way DiL
switches
G13-0000, G13-1000 totaliser Special E10 & E14 As above for acceptor
G13-6000, G13-7000 totaliser Special E10 & E14 As above for acceptor
G10-4000, G10-4000/2 G10-4000
G10-4000/5 & G10-4000/6 & G10-4000/5 Ask for individual variants supported
G10-4000/9 E15
G26 (G10-4000 validator) Special
G26 (G10-4000/5 validator) Special
G18-0000 E20 & E21 & E22 & E24 G18-0000 Interface Adaptor and user-
supplied 24v PSU required
G18-3000 G18-3000 E14 & E20
G40-x3xx, G40-x4xx G40 E13 & E26
G40-x0xx, G40-x5xx, G40-x6xx G40 E14 & E20

Mektek2 Manual Jan 08 PDF

Uploaded by

Copyright:

Available Formats

Mektek2 Manual Jan 08 PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Mektek2 Manual Jan 08 PDF

Uploaded by

Copyright:

Available Formats

Mektek2 Manual V1.

Version 1.0 onwards

Reprogramming coin mechanisms

Mektek International Ltd Tel: (44) 1628 525525

Mektek2 V1.0 English

RS232 cable to PC serial port.

PROM programming socket

Sockets for looms to connect validator for

Socket for G13 Totaliser only

?? Click on Save Config and Exit. To modify settings select Change

How the programmer works

Credits (Lite version only)

Do not request further

If a Fault Message such

Loading Credits Message Table

Data storage devices

E+1V - suitable for both 1k & Switch setting

E+1A - suitable for both 1k &

Basic reprogramming routines

MARS – example MS1600

?? Click on OK when the message “Data Gathering Complete appears.

?? The estimated acceptance of each coin is displayed. If required adjust the

?? Insert an E+1 in the socket of the Programmer.

?? Check that both switches are ON

?? The E+1 has been programmed

Legs firmly seated in socket.

Correct orientation and rear of PCB

?? Click on Validator Test

Coin Controls/NRI – example G13-6000

?? Click on OK when the message “Data Gathering Complete” appears.

?? The contents of the

?? The estimated acceptance of each coin is displayed. If required adjust the

?? Click on Validator Test

?? Click on OK and drop 20 coins

Discriminating against a known slug

Using a Coinset file:

Using a Slug Fix Wizard:

?? The contents of the PROM will be displayed in the left box.

Display of other information (eg parameters, mapping, etc):

Program from File:

NRI only - method

Coin Controls only - method:

Reprogramming – by coin mech type

Programme as basic MARS routine but note the following:

ME111 family: See Appendix for listing of individual mechs supported.

?? Connect loom E2 from Socket 4 of

?? To return the mech to Segment 1 in order to use a

MS111B1 – there are no sets of pins on this

MS111 family: See Appendix for listing of individual mechs supported.

?? Connect loom E8 from Socket 4 on

Bipolar PROM usage:

Additional features included in later version operating software

C120 family: See Appendix for listing of individual mechs supported.

Old & new type mechanism identification:

Display of other information:

Coin Accept Mode:

Acceptance faults when fitted to host machines:

Coin Accept Mode:

Acceptance faults when fitted to host machines or validator test: