G.

SHDSL Router - WS5300-4port

User’s Manual
G.SHDSL Router – WS5300-4port Version 2.0

Table of Contents

1. PRODUCT OVERVIEW....................................................................................1
1.1 PREFACE.......................................................................................................1
1.2 OVERVIEW.....................................................................................................1
2. HARDWARE INSTALLATION .........................................................................2
2.1 FRONT PANEL LEDS INDICATORS ....................................................................2
2.2 REAR PANEL CONNECTORS ............................................................................3
2.3 INSTALLATION PROCEDURE .............................................................................3
3. CONFIGURING WITH CLI................................................................................4
3.1 CONSOLE SETUP ...........................................................................................4
3.2 MENU OVERVIEW ...........................................................................................5
3.3 LOGIN ...........................................................................................................5
3.3.1 Login .....................................................................................................5
3.3.2 Changing System Password.................................................................5
3.4 SETUP...........................................................................................................5
3.4.1 Main Menu ............................................................................................5
3.4.2 System Overview ..................................................................................7
3.4.3 System Operation Mode .......................................................................7
3.4.4 Bridge Mode .........................................................................................8
3.4.5 Router Mode .......................................................................................18
3.5 SYSTEM MAINTENANCE ................................................................................39
3.5.1 Load Factory Default...........................................................................40
3.5.2 General Maintenance..........................................................................41
3.5.3 Ping Test.............................................................................................42
3.5.4 Display Configuration..........................................................................43
3.5.5 Time Settings......................................................................................44
3.6 PERFORMANCE AND STATISTIC .....................................................................45
3.6.1 DSL.....................................................................................................46
3.6.2 ATM ....................................................................................................47
4. CONFIGURING WITH WEB ...........................................................................48
4.1 LOGIN .........................................................................................................48
4.2 WEB MENUS ................................................................................................48
4.3 SETUP.........................................................................................................49
4.3.1 System Information .............................................................................49
4.3.2 System Operation Mode .....................................................................50
4.3.3 Bridge Mode .......................................................................................52
4.3.4 Router Mode .......................................................................................60
4.4 MAINTENANCE .............................................................................................76
4.4.1 General Maintenance..........................................................................76
4.4.2 Time Settings......................................................................................76

1
G.SHDSL Router – WS5300-4port Version 2.0

4.4.3 Factory Default ...................................................................................77

4.4.4 Save....................................................................................................78
4.5 PERFORMANCE ............................................................................................78
4.5.1 DSL Performance & Statistic ..............................................................78
4.5.2 ATM Performance & Statistic..............................................................79
5. UPGRADING FIRMWARE .............................................................................80
5.1 UPGRADE USING ETHERNET PORT .................................................................80
5.2 UPGRADE USING SERIAL PORT ......................................................................81
APPENDIX..........................................................................................................90
APPENDIX A:INSTALL TFTP SOFTWARE ...............................................................90

2
G.SHDSL Router – WS5300-4port Version 2.0

1. Product Overview
1.1 Preface

The primary objective of this manual is to help network administrator operate WS5300-4port
bridge and router product. Strongly committed to user friendly, this manual will guide the users
step by step to turn the product up and running in the simplest way ever.

1.2 Overview

With the symmetrical data transmission up to 2.3 Mbps, also can up to 5.7M with the G.shdsl.bis
(Support only for RT mode) over the ordinary telephone line, SHDSL satisfies the needs of
multiple user of small office/home office (SOHO), who needs both bandwidth and permanent data
connection. Although SHDSL transmits data over the telephone line, it does not interrupt the
voice because it uses different frequency for data transmission. Therefore, the end-users are
able to access internet and to talk over the telephone simultaneously.

WS5300-4port is designed to provide user all features needed in the SOHO environment. This
product supports multiple virtual channels to connect to different location. Bridge and router
features are also supported in WS5300-4port.

1
G.SHDSL Router – WS5300-4port Version 2.0

2. Hardware Installation
2.1 Front Panel LEDs Indicators

There are eight LED indicators on the front panel of WS5300-4port. They show the statuses of
the device.

The functions of LED indicators are described in the following table:

LED Color Status Meaning

Steady The device is on.
PWR Orange
Off The device is off.
Steady The device is on and functioning properly.
SYS Orange
Off The device is booting or Off

Steady The device is Sync Status.

DSL Orange Blinking The link is synchronizing - this may take several minutes.
Off The device is unplugged or disconnected.

Blinking The device is sending or receiving data

ACT Orange
Off There’s no data sending or receiving.

LN1 Orange Steady Link 1 - The LAN connection is successfully established.

LN2 Orange Steady Link 2 - The LAN connection is successfully established.

LN3 Orange Steady Link 3 - The LAN connection is successfully established.

LN4 Orange Steady Link 4 - The LAN connection is successfully established.

2
G.SHDSL Router – WS5300-4port Version 2.0

2.2 Rear Panel Connectors

The rear panel connectors connecting the device to the LAN and xDSL network are illustrated as
below.
Note：Press the RESET button for more than 5 seconds, the device will be loaded to
factory default and reset automatically.

Power Adapter
Reset Console LAN 110VAC / 220 VAC~5VDC

RJ-11 RS-232 RJ-45

...
Phone Line
(xDSL)

Emulator Terminal
PC PC
VT-100

Figure 1 Rear Panel and Installation

2.3 Installation Procedure

Step 1. - Use RJ-11 cable to connect the device to xDSL line.

Step 2. - Use RS-232 cable to connect the console port of the device to serial port of the PC with
terminal emulator software installed.

Step 3. - Use RS-45 cable to connect the device and the PC which has the Network Interface
Card (NIC) installed. If you want to connect to an external hub, you have to use the RJ-45 cross-
over cable.

Step 4. - Plug in the Power adaptor to the DC Power socket of the device, then connect the
Power adaptor to the AC outlet.

3
G.SHDSL Router – WS5300-4port Version 2.0

3. Configuring with CLI

3.1 Console Setup

Step 1: Connect computer to the device through the console port as shown in the figure 1.
Step 2: Open the terminal emulator software (like Hyper-Terminal on Microsoft Windows machine,
or “ Minicom” on Linux machine), then select the proper COM port for the connection. Set the
terminal and port to the following parameters:

- Terminal Mode: VT-100

- Baud rate : 115200 bps
- Data bits :8
- Parity : None
- Stop bits :1
- Flow Control : None

Turning on the WS5300-4port, then after few seconds of machine initialization, the system
management terminal will display the login screen. Details see section 3.3.1.

Emulator Terminal
VT-100

10/100Base-T
DSLAM/ISP
RS-232

RJ-45 RJ-11
WS5300-4port
G.SHDSL
Bridge/Router INTERNET/
ATM

Figure 2 Console Setup

4
G.SHDSL Router – WS5300-4port Version 2.0

3.2 Menu Overview

You can refer to Main Menu, see section 3.4.1.

3.3 Login

3.3.1 Login

- Default Password: admin

3.3.2 Changing System Password

You can change the system password by following steps:

Login to the Main Menu:

Step 1. - Press ‘E’ to open menu ‘System Maintenance’

Step 2. - Press ‘B’ to open menu ‘General Maintenance’
Step 3. - Press ‘C’ to enter the old password.
Step 4. - Press ‘D’ to enter a new password.
Step 5. - Press ‘E’ to re-type the new password to confirm.
Step 6. - Press ‘ENTER’ key to update.

NOTE: To cancel the setup, press the key ‘ESC’.

3.4 Setup

3.4.1 Main Menu

It contains all the submenus of management system terminal in which the configuration of device
can be set.

5
G.SHDSL Router – WS5300-4port Version 2.0

6
G.SHDSL Router – WS5300-4port Version 2.0

3.4.2 System Overview

From Main Menu, press ‘A’ to open menu System Overview.

In this menu, it shows the current system information such as: System Name, Model, Firmware
Version, CPU, RAM, Flash size, DSL chipset and Current Time.

3.4.3 System Operation Mode

You can set System Operation Mode: BRIDGE or ROUTER from two different menus:-

a. In menu ‘Quick Setup’:

From Main Menu,

Step 1: - Press ‘B’ - to open menu ‘Quick Setup’
Step 2: - Press ‘A’ - to select item Operation Mode
Step 3: - Press ‘Space Bar’ - to toggle between BRIDGE / ROUTER mode
Step 4: - Press ‘Enter’ - to update the system operation mode

b. In menu ‘System Setup’

From Main Menu,

Step 1: - Press ‘C’ - to open menu ‘Basic Configuration’
Step 2: - Press ‘A’ - to open menu ‘System Setup’
Step 3: - Press ‘A’ - to select item Operation Mode
Step 4: - Press ‘Space Bar’ - to toggle between BRIDGE / ROUTER mode
Step 5: - Press ‘Enter’ - to update the system operation mode

NOTE: You must press ‘Enter’ to update system configuration after selecting the operation mode.

7
 G.SHDSL Router – WS5300-4port Version 2.0

3.4.4 Bridge Mode

In Bridge mode, WS5300-4port provides frame forward services between two or more LANs. It
forwards frames based on the MAC (Medium Access Control) addresses which is hardware-level
of NICs (Network Interface Card)

The operation mode of the system must set to BRIDGE Mode. To change the mode, please see
the section 3.4.3. The following sections will help you to do configuration the device in BRIDGE
mode by using the system management terminal.

The application of the G.SHDSL Modem in Bridge Mode are illustrated in the following figures

DSLAM / ISP

G.SHDSL Modem
WS5300-4port
Bridge VPI/VCI INTERNET
IP Address RFC2684

Corporation LAN

Figure 4 Bridge Mode - Application of TC-505GL: Internet Access

G.SHDSL Modem G.SHDSL Modem

WS5300-4port ATM WS5300-4port

Bridge VPI/VCI Bridge

IP Address VPI/VCI RFC2684 IP Address
RFC2684

Branch Office LAN

Corporation LAN

Figure 5 Bridge Mode - Application of TC-505GL: LAN-to-LAN

8
G.SHDSL Router – WS5300-4port Version 2.0

3.4.4.1 Quick Setup:

From Main Menu, press ‘B’ to open menu ‘Quick Setup’

Using this setup, the device can be quickly configured and operated properly. The WAN
configuration is for the first Virtual Circuit ( VC 1 ) in twelve VC set available in the device.

The details of the items are described in the following table:

Item Field Name Description Value

BRIDGE /
System operation mode. Press ‘Space Bar’ to
A Operation Mode ROUTER
select the setting.
Default: BRIDGE
System service type. System can be
RT / COT
Service Type operated as RT or COT type. Press ‘Space
Default: RT
Bar’ to select the setting.
B
ETSI / ANSI/
Standard Mode Physical standard mode. ANNEX-F**
Default: ETSI
VPI Virtual Path Identifier, given by ISP. 0 - 16
C
VCI Virtual Channel Identifier, given by ISP. 33 - 4096
Bridge IP
D The device IP address. i.e ‘192.168.0.2’
Address
Note: **WS5300-4port only support ANNEX-F in RT mode with 2 Wire.

9
G.SHDSL Router – WS5300-4port Version 2.0

3.4.4.2 Basic Configuration:

From Main Menu,
- Press ‘C’ to open menu ‘Basic Configuration’.

In menu Basic Configuration, the system can be configured in submenus: System Setup and
WAN setup.

10
G.SHDSL Router – WS5300-4port Version 2.0

System Setup

From Main Menu,

- Press ‘C’ to open menu ‘Basic Configuration’.
- Press ‘A’ to open menu ‘System Setup’

In menu System Setup, it contains the system related configuration such as: operation mode,
service type, physical standard mode, Data Rate mode and so on.

The details of the items are described in the following table:

Item Field Name Description Value

System operation mode. Press ‘Space Bar’ BRIDGE / ROUTER
A Operation Mode
to select the setting. Default: BRIDGE
System service type. System can be
RT / COT
Service Type operated as RT or COT type. Press ‘Space
Default: RT
Bar’ to select the setting.
B
ETSI / ANSI/
Physical standard mode. Press ‘Space Bar’
Standard Mode ANNEX-F**
to select the setting.
Default: ETSI
Data transferred rate mode. Press ‘Space ADAPTIVE / FIXED
C Data Rate Mode
Bar’ to select the setting. Default: ADAPTIVE
Date rate range.
In Adaptive mode, the data rate can be
ADAPTIVE: 192~2304
D* Range changed in the range 192~2304 kbps.
FIXED: 64 - 2304
In Fixed mode, it is set in the range 64~2304
kbps. Press ‘Space Bar’ to select the setting.
Auto-Negotiation/10M
ETHERNET
E Specify the operation mode of LAN port. half/10M full/100M
Connectivity
half/100M full
Note: * applicable for Data Rate FIXED mode only
Note: **WS5300-4port only support ANNEX-F in RT mode with 2 Wire.

11
G.SHDSL Router – WS5300-4port Version 2.0

WAN setup

From Main Menu,

- Press ‘C’ to open menu ‘Basic Configuration’.

- Press ‘B’ to open menu ‘WAN Setup’

In menu WAN Setup, it shows the list of Virtual Circuits (VCs) and their statuses.

If a VC is already configured then it displays its name as a identification, otherwise it displays a

underscore line.

If a VC is already activated, then in the field ‘Active’, it displays the word ‘Yes’, otherwise it
displays a dash.

12
G.SHDSL Router – WS5300-4port Version 2.0

1)To setup VC configuration,

- Press an key ‘A’ to ‘L’ for an appropriate VC, i.e ‘A’ for VC 1, ‘B’ for VC 2...

13
G.SHDSL Router – WS5300-4port Version 2.0

2)To Delete VC configuration,

- Press ‘Space Bar’, then follow the instructions in the bottom line.

The details of the items are described in the following table:

Item Field Name Description Value

A ISP Name ISP Name Max. 18 characters

B VPI Virtual Path Identifier, given by ISP 0 - 16

VCI Virtual Channel Identifier, given by ISP 33 - 4096

Encapsulation Encapsulation type Always set RFC2684

Header to identify the protocol that Virtual
Circuit being carrying.
LLC / VCMUX
Multiplex LLC: Logical Link Control Multiplexing
Default: LLC
VCMUX : VC-based Multiplexing
By press ‘Space Bar’ to select the setting.
Quality of Services
UBR: Unspecified Bit Rate. UBR / CBR / rt-VBR /
CBR: Constant Bit Rate. nrt-VBR
C QoS rt-VBR: Real-Time Variable Bit Rate. Default: UBR
nrt-VBR: Non-Real-Time Variable Bit
Rate.
Press ‘Space Bar’ to select the setting.
Peak Cell Rate
D The maximum transmission rate. 0 - 5424
(PCR)
Sustained Cell
E The Transmission rate in a burst traffic. 0 - PCR
Rate (SCR)
Maximum Burst Maximum number of transmission cell at
F 0 - 1000
Size (MBS) the peak rate.

14
G.SHDSL Router – WS5300-4port Version 2.0

3.4.4.3 Advanced Configuration:

From Main Menu,

- Press ‘D’ to open menu ‘Advanced Configuration’.

In submenu Bridging and SNMP under menu Advanced Configuration, it will help you to configure
the system related information such as: Bridging IP address, Spanning Tree, Priority, SNMP.

15
G.SHDSL Router – WS5300-4port Version 2.0

Bridging

From Main Menu,

- Press ‘D’ to open menu ‘Advanced Configuration’.

- Press ‘A’ to open menu ‘Bridging’.

The details of the items are described in the following table:

Item Field Name Description Value

A Bridge IP Address Bridge IP Address i.e: ’192.168.0.2’

Specify Default Gateway address of the
B Default Gateway None
unit.
Spanning Tree Learning Bridge Protocol. Disable/Enable
C Spanning Tree
Press ‘Space Bar to select the settings. Default: Disable
D Priority Specify the priority. 0-65535

16
G.SHDSL Router – WS5300-4port Version 2.0

SNMP

From Main Menu,

- Press ‘D’ to open menu ‘Advanced Configuration’.

- Press ‘B’ to open menu ‘SNMP.

The details of the items are described in the following table:

Item Field Name Description Value

Disable or Enable the SNMP management Disable/Enable
A SNMP
feature. Default: Disable
Specify the community name of external
B Read-Only Community SNMP Managers allowed with access level Public
of “ Read “ to the unit’s MIB.
Specify the community name of external
C Read-Write Community SNMP Managers allowed with access level Private
of “ Read & write “ to the unit’s MIB.
Specify the community name of external
D TRAP Community SNMP Managers allowed to receive the Public
TRAP message.
Specify TRAP version and destination IP
E-H Version address that the TRAP message is intended None
for.

17
 G.SHDSL Router – WS5300-4port Version 2.0

3.4.5 Router Mode

The operation mode of the system must set to ROUTER Mode. To change the mode, please see
the section 3.4.3. The following sections will help you to do configuration the device in Router
mode.

The application of the G.SHDSL Modem in Router Mode are illustrated in the following figures

DSLAM / ISP
G.SHDSL Router VPI/VCI
TC-505GL Encapsulation
Multiplexing

TC-505GL
INTERNET
LAN
IP Address / WAN Remote
Subnet Mask IP Address / IP Address
Subnet Mask

Corporation LAN

Figure 6 Router Mode - Application of TC-505GL: Internet Access

DSLAM / ISP DSLAM / ISP

G.SHDSL Router G.SHDSL Router

TC-505GL TC-505GL

TC-505GL ATM TC-505GL

VPI/VCI VPI/VCI
LAN Encapsulation Encapsulation
IP Address / Multiplexing Multiplexing LAN
SubnetMask IP Address /
SubnetMask

Branch Office LAN

Corporation LAN

Figure 7 Router Mode - Application of TC-505GL: LAN-to-LAN

18
G.SHDSL Router – WS5300-4port Version 2.0

3.4.5.1 Quick Setup:

From Main Menu, press ‘B’ to open menu ‘Quick Setup’.

Using this setup, the device can be quickly configured and operated properly.

Note: The WAN configuration is for the first Virtual Circuit ( VC 1 ) in twelve VC set available in
the device.

19
G.SHDSL Router – WS5300-4port Version 2.0

The details of the items are described in the following table:

Item Field Name Description Value

System operation mode. Press ‘Space BRIDGE / ROUTER
A Operation Mode
Bar’ to select the setting. Default: BRIDGE
System service type. System can be
RT / COT
B Service Type operated as RT or COT type. Press
Default: RT
‘Space Bar’ to select the setting.
ETSI / ANSI/
Physical standard mode. Press ‘Space
Standard Mode ANNEX-F**
Bar’ to select the setting.
Default: ETSI
Default:
C LAN IP Address Local IP Address of router.
‘192.168.0.1’
LAN IP Subnet Default:
Local Subnet Mask of router.
Mask ‘255.255.255.0’
D VPI Virtual Path Identifier 0 – 16

VCI Virtual Channel Identifier 33 - 4096

RFC2684 / IPoA /
The encapsulation type is given by ISP. PPPoE / PPPoA
Encapsulation
Press ‘Space Bar’ to select the setting.
Default: PPPoA
Dynamic IP Disable/Enable
E Press ‘Space Bar’ to select the setting.
Address Default: Disable
F IP Un-numbered Press ‘Space Bar’ to select the setting. Disable/Enable
The WAN local IP Address of router,
G WAN IP Address i.e ‘123.221.79.2’
given by ISP
WAN IP Subnet The WAN local IP subnet mask of router,
i.e ‘255.0.0.0’
Mask given by ISP
H Remote IP Address The IP Address of DSLAM, given by ISP i.e ‘229.122.79.32’
ISP login user name, given by ISP. It is
I User Name set for the encapsulation type of PPPoE Max. 30 characters
or PPPoA
ISP login password, given by ISP. It is
Password set for the encapsulation type of PPPoE Max. 30 characters
or PPPoA
IP Sharing or NAT (Network Access
Disable / Enable
J IP Sharing Translation). Press ‘Space Bar’ to select
Default: Disable
the settings.

Note: **WS5300-4port only support ANNEX-F in RT mode with 2 Wire.

20
G.SHDSL Router – WS5300-4port Version 2.0

3.4.5.2 Basic Configuration:

From Main Menu,

- Press ‘C’ to open menu ‘Basic Configuration’.

In menu Basic Configuration, the system can be configured in individual submenu: System Setup,
LAN Setup and WAN setup.

System Setup:

From Main Menu,

- Press ‘C’ to open menu ‘Basic Configuration’.

- Press ‘A’ to open menu ‘System Setup’

In menu System Setup, it contains the system related configuration such as: operation mode,
service type, physical standard mode, Data Rate mode.

21
G.SHDSL Router – WS5300-4port Version 2.0

The details of the items are described in the following table:

Item Field Name Description Value

System operation mode. Press ‘Space Bar’ to
A Operation Mode BRIDGE / ROUTER
select the settings.
System service type. System can be operated RT / COT
Service Type as RT or COT type. Press ‘Space Bar’ to Default: RT
select the settings.
B
ETSI / ANSI/
Physical standard mode. Press ‘Space Bar’ to
Standard Mode ANNEX-F **
select the settings.
Default: ETSI
Data transferred rate mode. Press ‘Space Bar’
C Data Rate Mode ADAPTIVE / FIXED
to select the settings.
Date rate range.
In Adaptive mode, the data rate can be ADAPTIVE:
D* Range changed in the range 192~2304 kbps. 192~2304
In Fixed mode, it is set in the range 64~2304 FIXED: 64 - 2304
kbps. Press ‘Space Bar’ to select the settings.

ETHERNET Auto-Negotiation/10M
E Connectivity Specify the operation mode of LAN port. half/10M full/100M
half/100M full

Note: * applicable for Data Rate FIXED mode only

Note: **WS5300-4port only support ANNEX-F in RT mode with 2 Wire.

22
G.SHDSL Router – WS5300-4port Version 2.0

LAN Setup

From Main Menu,

- Press ‘C’ to open menu ‘Basic Configuration’.
- Press ‘B’ to open menu ‘LAN Setup’

23
G.SHDSL Router – WS5300-4port Version 2.0

The details of the items are described in the following table:

Item Field Name Description Value

Default:
LAN IP Address LAN IP address of router
‘192.168.0.1’
A
LAN IP Subnet Default:
LAN IP subnet mask of router
Mask ‘255.255.255.0’
No/Yes
B IP Alias IP Alias
Default:No
Dynamic Host Configuration Protocol -
allows dynamically for any of the
Disable / Enable
C DHCP Server connected hosts on a LAN that support
Default:Disable
DHCP clients. Press ‘Space Bar’ to
select the settings.
DHCP Relay
D DHCP Relay Server IP None
Server IP
Starting IP Address in the range in which
the IP address of hosts on the LAN will
Starting IP Address i.e: ‘192.168.0.2’
be assigned, case of DHCP server set
Enable
E
Ending IP Address in the range in which
the IP address of hosts on the LAN will
Ending IP Address i.e: ‘192.168.0.254’
be assigned, case of DHCP server set
Enable
Disable/Enable
F DNS Proxy Enable or Disalbe DNS Proxy
Default:Disable
Domain Name System - Primary DNS
server IP address for resolving the
DNS 1 i.e: ‘209.226.174.220’
symbolic IP (like www.yahoo.com) to
G
numeric IP address (like 216.109.118.74)
DNS 2 Secondary DNS server IP address i.e: ‘198.235.217.132’
Amount of time that a given IP address
H Leased Time 0-864000
will be valid.

24
G.SHDSL Router – WS5300-4port Version 2.0

WAN setup

From Main Menu,

- Press ‘C’ to open menu ‘Basic Configuration’.

- Press ‘C’ to open menu ‘WAN Setup’

To setup VC configuration,
- Press an key ‘A’ to ‘L’ for an appropriate VC, i.e ‘A’ for VC 1, ‘B’ for VC 2...
-
To Delete VC configuration,
- Press ‘Space Bar’, then follow the instruction in the bottom line.

In menu WAN Setup, it shows the list of Virtual Circuits (VCs) and their statuses.

If a VC is already configured then it display its name as a identification, otherwise it displays a

underscore line.

If the VC is already activated, then in the field ‘Active’, it displays the word ‘Yes’, otherwise it
displays a dash.

If the VC set with the encapsulation type of PPPoE or PPPoA, then in the field PPP Status it
displays the status of PPP connection: ‘Disconnected’, ‘Connecting’ or ‘Connected’.

25
G.SHDSL Router – WS5300-4port Version 2.0

VC setup:
From Main Menu,
- Press ‘C’ to open menu ‘Basic Configuration’.
- Press ‘C’ to open menu ‘WAN Setup’
- Press ‘A’ to ‘L’ to open the menu ‘VC Setup’ for the appropriate VC set.

26
G.SHDSL Router – WS5300-4port Version 2.0

The detail of item are described in the following table:

Item Field Name Description Value

A ISP Name ISP Name Max. 18 characters

VPI Virtual Path Identifier, given by ISP 0 – 16

VCI Virtual Channel Identifier, given by ISP 33 - 4096

RFC2684 / IPoA /
The encapsulation type is given by ISP.
Encapsulation PPPoE / PPPoA
B Press ‘Space Bar’ to select the setting.
Default: PPPoA
Header to identify the protocol that Virtual
Circuit being carrying.
LLC / VCMUX
Multiplex LLC: Logical Link Control Multiplexing
Default: LLC
VCMUX : VC-based Multiplexing
By press ‘Space Bar’ to select the seting.
Quality of Services
UBR / CBR / rt-
UBR: Unspecified Bit Rate.
VBR / nrt-VBR
CBR: Constant Bit Rate.
C QoS Default: UBR
rt-VBR: Real-Time Variable Bit Rate.
nrt-VBR: Non-Real-Time Variable Bit Rate.
Press ‘Space Bar’ to select the setting.
Peak Cell Rate
D The maximum transmission rate. 0 - 5424
(PCR)
Sustained Cell
E The Transmission rate in a burst traffic. 0 - PCR
Rate (SCR)
Maximum Burst Maximum number of transmission cell at the
F 0 - 1000
Size (MBS) peak rate.
Dynamic IP Disable/Enable
G Press ‘Space Bar’ to select the setting.
Address Default: Disable
H IP Un-numbered Press ‘Space Bar’ to select the setting. Disable/Enable
The WAN local IP Address of router, given
I WAN IP Address i.e ‘123.221.79.2’
by ISP
WAN IP Subnet The WAN local IP subnet mask of router,
i.e ‘255.0.0.0’
Mask given by ISP
J Remote IP Address The IP Address of DSLAM, given by ISP i.e ‘229.122.79.32’
ISP login user name, given by ISP. It is set
User Name for the encapsulation type of PPPoE or Max. 30 characters
PPPoA
K
ISP login password, given by ISP. It is set
Password for the encapsulation type of PPPoE or Max. 30 characters
PPPoA
IP Sharing or NAT (Network Access
Disable / Enable
L IP Sharing Translation). Press ‘Space Bar’ to select
Default: Disable
the settings.

27
G.SHDSL Router – WS5300-4port Version 2.0

3.4.5.3 Advanced Configuration:

From Main Menu,

- Press ‘D’ to open menu ‘Advanced Configuration’.

In menu Advance Configuration, the system can be configured in the submenu Routing, SNMP,
Forwarding, DMZ ,VPN, Access List &IP Filtering, and WAN-DHCP Relay

28
G.SHDSL Router – WS5300-4port Version 2.0

Routing

From Main Menu,

- Press ‘D’ to open menu ‘Advanced Configuration’.

- Press ‘A’ to open menu ‘Routing’.

The details of the items are described in the following table:

Item Field Name Description Value

With Dynamic Routing, you can enable WS5300- Disable /
4port to automatically adjust to physical changes in Enable
RIP
the network’s topology. Default:
Dynamic
Enable or disable the Routing Information Protocol. Disable
Routing
RIP version determines the format and broadcasting RIP-1 / RIP-2
Version method of any RIP transmissions by the WS5300- Default: RIP-
4port. 2
A static route is a pre-configured path that data must
traverse to reach a specific host or network. i.e ’10.10.10.
IP Address
Specify the Destination IP Address for entry in the 50’
static routing table.
Static
i.e
Routing Specify the Subnet Mask for the network configured
IP Subnet Mask ‘255.255.255.
in the static routing table.
0’
i.e ’192.168.0
Gateway Specify the IP address of Gateway.
.1’

29
G.SHDSL Router – WS5300-4port Version 2.0

SNMP

From Main Menu,

- Press ‘D’ to select ‘Advanced Configuration’ menu.

- Press ‘B’ to select ‘SNMP’ menu.

The details of the items are described in the following table:

Item Field Name Description Value

Disable or Enable the SNMP management Disable/Enable
A SNMP
feature.. Default: Disable
Specify the community name of external
B Read-Only Community SNMP Managers allowed with access level Public
of “ Read “ to the unit’s MIB.
Specify the community name of external
C Read-Write Community SNMP Managers allowed with access level Private
of “ Read & write “ to the unit’s MIB.
Specify the community name of external
D TRAP Community SNMP Managers allowed to receive the Public
TRAP message.
Specify TRAP version and destination IP
E-H Version address that the TRAP message is intended None
for.

30
G.SHDSL Router – WS5300-4port Version 2.0

Forwarding

From Main Menu,

- Press ‘D’ to select ‘Advanced Configuration’ menu.
- Press ‘C’ to select ‘Forwarding’ menu.

The details of the items are described in the following table:

Item Field Name Description Value

A WEB Map WEB server on LAN for external Internet services. None
None
B FTP Map FTP server on LAN for external Internet services.
None
C TELNET Map TELNET server on LAN for external Internet services.
Specify application parameters including VC Index, Port None
D-K
Number, Protocol, IP addresses.

31
G.SHDSL Router – WS5300-4port Version 2.0

DMZ

From Main Menu,

- Press ‘D’ to open ‘Advanced Configuration’ menu.
- Press ‘D’ to open ‘DMZ’ menu.

The details of the items are described in the following table:

Item Field Name Description Value

Specify DMZ application parameters
A None
including VC Index, Host IP addresses

32
G.SHDSL Router – WS5300-4port Version 2.0

VPN

From Main Menu,

- Press ‘D’ to open the ‘Advanced Configuration’ menu.
- Press ‘E’ to open the ‘VPN’ menu.

The details of the items are described in the following table:

Item Field Name Description Value

IPSec pass Enable or disable the pass through of IPSec Disable/Enable
A
through tunnel between two VPN end points. Default:Disable
Enable or disable the pass through of L2TP Disable/Enable
B L2TP pass through
tunnel between two VPN end points. Default:Disable
PPTP pass Enable or disable the pass through of PPTP Disable/Enable
C
through tunnel between two VPN end points. Default:Disable

33
G.SHDSL Router – WS5300-4port Version 2.0

Access List & IP Filtering

From Main Menu,

- Press ‘D’ to open the ‘Advanced Configuration’ menu.

- Press ‘F’ to open the ‘Access Control List’ menu.

34
G.SHDSL Router – WS5300-4port Version 2.0

- Press ‘A’ to open the ‘Standard Access Control List’ menu.

Item Field Name Description Value

A Select index Specify a standard ACL number from 1 to 99 None

B Show ACL Show all current Access Control List. None

35
G.SHDSL Router – WS5300-4port Version 2.0

- Press ‘B’ to open the ‘Extended Access Control List- IP Filtering’ menu.

Item Field Name Description Value

A Select index Specify a standard ACL number from 101 to 199 None

B Show ACL Show all current Access Control List. None

36
G.SHDSL Router – WS5300-4port Version 2.0

- Press ‘C’ to open the ‘Denial of Service Protection’ menu.

Item Field Name Description Value

Disable/Enable
A Anti-spoofing Disable/Enable Anti-spoofing
Default:Disable
Illegal TCP flags Disable/Enable
B Disable/Enable Illegal TCP flags detection
detection Default:Disable
SYN flooding Disable/Enable
C Disable/Enable SYN flooding detection
detection Default:Disable

37
G.SHDSL Router – WS5300-4port Version 2.0

WAN-DHCP Relay

Item Field Name Description Value

A VC Index Specify VC Index None

DHCP Relay
B Specify DHCP Relay Server IP None
Server IP
WAN-DHCP Disable/Enable
C Disable/Enable WAN-DHCP relay
relay Default:Disable

38
G.SHDSL Router – WS5300-4port Version 2.0

3.5 System Maintenance

From Main Menu,

- Press ‘E’ to open menu ‘System Maintenance’.

39
G.SHDSL Router – WS5300-4port Version 2.0

3.5.1 Load Factory Default

From Main Menu,

- Press ‘E’ to open the ‘System Maintenance’ menu.

- Press ‘A’ to open the ‘Load Factory Default’ menu.

If you type “Y” to re-load factory default, the device will reboot by itself.

40
G.SHDSL Router – WS5300-4port Version 2.0

3.5.2 General Maintenance

From Main Menu,

- Press ‘E’ to open the ‘System Maintenance’ menu.

- Press ‘B’ to open the ‘General Maintenance’ menu.

The details of the items are described in the following table:

Item Field Name Description Value

A System Name The system name Max. 18 characters

System service type. System can be
RT / COT
B Service Type operated as RT or COT type. Press
Default: RT
‘Space Bar’ to select the setting.
You must input the corrected old
C Old Password Max. 18 characters
password before set new password.
D New Password The new password Max. 18 characters
Re-type New It must be exactly the same new
E Max. 18 characters
Password password in the item ‘D’

41
G.SHDSL Router – WS5300-4port Version 2.0

3.5.3 Ping Test

From Main Menu,

- Press ‘E’ to open the ‘System Maintenance’ menu.

- Press ‘C’ to open the ‘Ping Test’ menu.

Note: If the test is successful then it will display a message: ‘ <Host IP> is alive! ’. Otherwise it will
display a message “Network is unreachable” or “No response”.

42
G.SHDSL Router – WS5300-4port Version 2.0

3.5.4 Display Configuration

From Main Menu,

- Press ‘E’ to open the ‘System Maintenance’ menu.

- Press ‘D’ to open the ‘Display Configuration’ menu

Press “m” or “M” to see more information

43
G.SHDSL Router – WS5300-4port Version 2.0

3.5.5 Time Settings

Item Field Name Description Value

A Time Server IP Specify Time Server IP None

B Time Zone Specify Time Zone None

Disable/Enable
C Auto Synchronisation Disable/Enable Auto Synchronisation
Default:Disable

44
G.SHDSL Router – WS5300-4port Version 2.0

3.6 Performance and Statistic

From Main Menu,

- Press ‘F’ to open menu ‘Performance & Statistic’.

In menu ‘Performance & Statistic’, you can test the performance of the DSL line and the ATM
interfaces which are already setup and activated.

45
G.SHDSL Router – WS5300-4port Version 2.0

3.6.1 DSL

From Main Menu,

- Press ‘F’ to open the ‘Performance & Statistic’ menu.
- Press ‘A’ to open the ‘DSL Performance & Statistic’ menu.

And you can see the information of Line Code,Standard,Service mode,Attenuation,and Line
Status.

An Example of DSL performance in active operation

46
G.SHDSL Router – WS5300-4port Version 2.0

3.6.2 ATM

From Main Menu,

- Press ‘F’ to open the ‘Performance & Statistic’ menu.

- Press ‘B’ to open the ‘ATM Performance & Statistic’ menu.

47
G.SHDSL Router – WS5300-4port Version 2.0

4. Configuring with WEB

4.1 Login

When connected, the WS5300-4port has the following pre-configured host IP addresses
“ 192.168.0.1 “ as shown below.

To access the Web Utility,

„ Configure your PC to the same network segment as the WS5300-4port. For example, you
could set the PC to IP address 192.168.0.10 with a subnet mask of 255.255.255.0.
„ Connect the PC to any of LAN port designated 1, 2, 3 or 4 on the Front Panel.
„ Open the Web browser.
„ Enter the IP address of the WS5300-4port.in the address field of the browser as exampled:
http://192.168.0.1 and then press <Enter> to connect.
„ There is a default User Name “admin” for the WS5300-4port.
„ Enter Password “ admin “.

4.2 Web Menus

On each Web Menu, there are two areas to illustrate:

‹ Menu Item: On the left side of the Web Menu is the menu items.
‹ Main Menu: The remaining area of Web Menu provides fields for configuration, specific to
each menu item, and displays prompt or Performance & Diagnostic data.

48
G.SHDSL Router – WS5300-4port Version 2.0

4.3 Setup

4.3.1 System Information

Menu “ System Information “ allows you to view and verify the unit’s identity information as shown
below.

In this menu, it shows the current system information such as: System Name, Model, Firmware
Version, CPU, RAM, Flash size and DSL chipset.

Items Description
System Name : Display the name of the unit.
Model : Display the model name.
Firmware Version : Display the current software version.
CPU : Display the CPU chipset and its operating frequency.
RAM : Display the size of the RAM Memory.
Flash : Display the size of the Flash Memory.
Uptime : Display the time of the System get up
DSL uptime : Display the time of the DSL get Sync
SHDSL Chipset : Display the chip name.

49
G.SHDSL Router – WS5300-4port Version 2.0

4.3.2 System Operation Mode

You can set System Operation Mode: BRIDGE or ROUTER from two different menus:-

1. From menu “Quick Setup”,

Step 1: - Click the option button Router or Bridge to select Operation Mode
Step 2: - Click Apply button to update the system operation mode

50
G.SHDSL Router – WS5300-4port Version 2.0

2. From menu “System”

Step 1: - Click the option button Router or Bridge to select Operation Mode
Step 2: - Click Apply button to update the system operation mode

51
G.SHDSL Router – WS5300-4port Version 2.0

4.3.3 Bridge Mode

In Bridge mode, WS5300-4port provides frame forward services between two or more LANs. It
forwards frames based on the MAC (Medium Access Control) addresses which is hardware-level
of NICs (Network Interface Card)

The operation mode of the system must set to BRIDGE Mode. To change the mode with WEB,
please see the section 4.3.2. The following sections will help you to do configuration the device
in BRIDGE mode.

Regarding to the application of the G.SHDSL Modem in Bridge Mode, please see the section
3.4.4.

52
G.SHDSL Router – WS5300-4port Version 2.0

4.3.3.1 Quick Set-up

Using this setup, the device can be quickly configured and operated properly.
Note: The WAN configuration is for the first Virtual Circuit ( VC 1 ) in twelve VC set available in
the device.

The details of the items are described in the following table:

Item Field Name Description Value

BRIDGE / ROUTER
Operation Mode System operation mode.
Default: BRIDGE
System service type. System can be
RT / COT
Service Type operated as RT or COT type. Select
Default: RT
System from the drop-down list.
ETSI / ANSI/
Physical standard mode. Select from ANNEX-F **
Standard Mode
the drop-down list. Default: ETSI

VPI Virtual Path Identifier 0 - 16

Wan VCI Virtual Channel Identifier 33 - 4096

The encapsulation type is given by ISP. RFC2684
Encapsulation
Select from the drop-down list. Default: RFC2684
BRIDGE IP Address The device IP address. i.e ‘192.168.0.1’
Note: **WS5300-4port only support ANNEX-F in RT mode with 2 Wire.

4.3.3.2 Basic Configuration

In menu Basic Configuration, the system can be configured in individual submenu: System Setup,
and WAN setup.

System

53
G.SHDSL Router – WS5300-4port Version 2.0

In menu “System”, it contains the system related configuration such as: operation mode, service
type, physical standard mode, Data Rate mode, and so on.

54
G.SHDSL Router – WS5300-4port Version 2.0

The details of the items are described in the following table:

Item Field Name Description Value

Operation Mode System operation mode. BRIDGE / ROUTER

System service type. System can be
RT / COT
Service Type operated as RT or COT type. Select
Default: RT
from the drop-down list.
ETSI / ANSI/
Physical standard mode. Select from the
Standard Mode ANNEX-F **
drop-down list.
Default: ETSI
ADAPTIVE / FIXED
Data Rate Mode Data transferred rate mode.
Default: ADAPTIVE
System Date rate range.
In Adaptive mode, the data rate can be
ADAPTIVE: 192~2304
Range changed in the range 192~2304 kbps.
FIXED: 64 - 2304
In Fixed mode, it is set in the range
64~2304 kbps.

Auto-Negotiation/10M
ETHERNET
Specify the operation mode of LAN port. half/10M full/100M
Connectivity
half/100M full

Note: **WS5300-4port only support ANNEX-F in RT mode with 2 Wire.

55
G.SHDSL Router – WS5300-4port Version 2.0

WAN

To setup VC configuration,
- Click submenu channel 1 to channel 12 for an appropriate VC, i.e ‘channel1’ for VC 1,
‘channel2’ for VC 2...
-
To Delete VC configuration,
- Click submenu channel 1 to channel 12 for an appropriate VC, then click button “Delete
VC …”

In menu WAN Setup, it shows the list of Virtual Circuits (VCs):channel 1 to channel 12

If a VC is already configured then it display its parameters as ISP Name, VPI,VCI, and so on.

If the VC is already activated, then in the field ‘Active’, it displays the word ‘Yes’, otherwise it
displays a ‘No’.

If the VC set with the encapsulation type of PPPoE or PPPoA, then in the field Encapsulation it
displays the status of PPP connection: RFC2684,IpoA, PPPoE or PPPoA

56
G.SHDSL Router – WS5300-4port Version 2.0

The details of the items are described in the following table:

Item Field Name Description Value

ISP Name ISP Name Max. 18 characters

VPI Virtual Path Identifier, given by ISP 0 – 16

VCI Virtual Channel Identifier, given by ISP 33 – 4096

The encapsulation type is given by ISP. RFC2684
Encapsulation
Select from the drop-down list. Default: RFC2684
Header to identify the protocol that
Virtual Circuit being carrying.
LLC / VCMUX
Multiplex LLC: Logical Link Control Multiplexing
Default: LLC
VCMUX : VC-based Multiplexing
Select from the drop-down list..
VC1 Quality of Services
UBR: Unspecified Bit Rate. UBR / CBR / rt-VBR /
CBR: Constant Bit Rate. nrt-VBR
QoS rt-VBR: Real-Time Variable Bit Rate. Default: UBR
nrt-VBR: Non-Real-Time Variable Bit
Rate.
Select from the drop-down list.
Peak Cell Rate
The maximum transmission rate. 0 – 5424
(PCR)
Sustained Cell
The Transmission rate in a burst traffic. 0 – PCR
Rate (SCR)
Maximum Burst Maximum number of transmission cell at
0 – 1000
Size (MBS) the peak rate.

57
G.SHDSL Router – WS5300-4port Version 2.0

4.3.3.3 Advanced Configuration

In menu “Advance Configuration”, the system can be configured in the submenu Bridge and
SNMP,

Bridge

The details of the items are described in the following table:

Item Field Name Description Value

IP Address Bridge IP Address i.e: ’192.168.0.1’

Specify Default Gateway address of the
Default Gateway None
unit.
Bridge
Disable/Enable
Spanning Tree Spanning Tree Learning Bridge Protocol.
Default: Disable
Priority Specify the priority. 0-65535

58
G.SHDSL Router – WS5300-4port Version 2.0

SNMP

To configure the SNMP, go through the following steps.

„ Click the button to Enable or Disable SNMP management capabilities.

„
Community

Read-Only Community:
„ Specify the community name of external SNMP Managers allowed with access level of
“ Read “ to the unit’s MIB..
„
Read-Write Community:
„ Specify the community name of external SNMP Managers allowed with access level of
“ Read & write “ to the unit’s MIB.

Trap
To configure the Trap, go through the following steps.

„ Select the version number, SNMPv1 or SNMPv2, from the pull-down menu.
„ Specify the IP address of each SNMP Trap Manager in the correspondent Destination IP.
„ Select the options, None, Add or Delete, from the pull-down menu.
„ Click the “ Apply “ button to save the configuration.

59
G.SHDSL Router – WS5300-4port Version 2.0

4.3.4 Router Mode

The operation mode of the system must set to ROUTER Mode. To change the mode with WEB,
please see the section 4.3.2. The following sections will help you to do configuration the device in
Router mode.

Regarding to the application of the G.SHDSL Modem in Router Mode ,please see the section
3.4.5.

4.3.4.1 Quick Set-up

Using this setup, the device can be quickly configured and operated properly.
Note: The WAN configuration is for the first Virtual Circuit ( VC 1 ) in twelve VC set available in
the device.

60
G.SHDSL Router – WS5300-4port Version 2.0

The details of the items are described in the following table:

Item Field Name Description Value

BRIDGE / ROUTER
Operation Mode System operation mode.
Default: BRIDGE
System service type. System can be
RT / COT
Service Type operated as RT or COT type. Select
System Default: RT
from the drop-down list.
ETSI / ANSI/
Physical standard mode. Select from the
Standard Mode ANNEX-F **
drop-down list.
Default: ETS
Default:
LAN IP Address Local IP Address of router.
‘192.168.0.1’
LAN
LAN IP Subnet Default:
Local Subnet Mask of router.
Mask ‘255.255.255.0’
VPI Virtual Path Identifier 0 - 16

VCI Virtual Channel Identifier 33 - 4096

RFC2684 / IPoA /
The encapsulation type is given by ISP.
Encapsulation PPPoE / PPPoA
Select from the drop-down list.
Default: PPPoA
Dynamic IP Disable/Enable
Dynamic IP Address
Address Default: Disable
Disable/Enable
IP Un-numbered IP Un-numbered
Default: Disable
The WAN local IP Address of router,
WAN IP Address i.e ‘123.221.79.2’
WAN given by ISP
WAN IP Subnet The WAN local IP subnet mask of router,
i.e ‘255.0.0.0’
Mask given by ISP
Remote IP Address The IP Address of DSLAM, given by ISP i.e ‘229.122.79.32’
ISP login user name, given by ISP. It is
User Name set for the encapsulation type of PPPoE Max. 30 characters
or PPPoA
ISP login password, given by ISP. It is
Password set for the encapsulation type of PPPoE Max. 30 characters
or PPPoA
IP Sharing or NAT (Network Access Disable / Enable
IP Sharing
Translation). Default: Disable
Note: **WS5300-4port only support ANNEX-F in RT mode with 2 Wire.

4.3.4.2 Basic Configuration

In menu Basic Configuration, the system can be configured in individual submenu: System Setup,
LAN Setup and WAN setup.

61
G.SHDSL Router – WS5300-4port Version 2.0

System

In menu “System”, it contains the system related configuration such as: operation mode, service
type, physical standard mode, Data Rate mode.

The details of the items are described in the following table:

Item Field Name Description Value

Operation Mode System operation mode. BRIDGE / ROUTER

System service type. System can be
RT: Client
Service Type operated as RT or COT type. Select
COT: Server
from the drop-down list.
ETSI / ANSI/
Physical standard mode. Select from the
Standard Mode ANNEX-F **
drop-down list.
Default: ETS
System
Data Rate Mode Data transferred rate mode. ADAPTIVE / FIXED

Date rate range.

In Adaptive mode, the data rate can be
ADAPTIVE: 192~2304
Range changed in the range 192~2304 kbps.
FIXED: 64 - 2304
In Fixed mode, it is set in the range
64~2304 kbps.
Note: **WS5300-4port only support ANNEX-F in RT mode with 2 Wire

62
G.SHDSL Router – WS5300-4port Version 2.0

LAN

The details of the items are described in the following table:

63
G.SHDSL Router – WS5300-4port Version 2.0

The details of the items are described in the following table:

Item Field Name Description Value

Default:
IP Address LAN IP address of router
‘192.168.0.1’
TCP/IP Default:
IP Subnet Mask LAN IP subnet mask of router
‘255.255.255.0’
Alias Specify Alias ip and subnet mask Default:NO
Dynamic Host Configuration Protocol -
Disable / Enable
DHCP Server allows dynamically for any of the connected
Default:Disable
hosts on a LAN that support DHCP clients.
Relay Server Specify Relay Server IP None
Disable / Enable
DNS Proxy Enable or Disable DNS Proxy
Default:Disable
Starting IP Address in the range in which
the IP address of hosts on the LAN will be
Starting IP i.e: ‘192.168.0.2’
DHCP assigned, in case of DHCP server set to
“ Enable “.
Ending IP Address in the range in which
the IP address of hosts on the LAN will be
Ending IP i.e: ‘192.168.0.254’
assigned, in case of DHCP server set to
“ Enable “.
Domain Name System - Primary DNS
server IP address for resolving the
DNS 1 i.e: ‘209.226.174.220’
symbolic IP (like www.yahoo.com) to
numeric IP address (like 216.109.118.74)
DNS 2 Secondary DNS server IP address i.e: ‘198.235.217.132’
Amount of time that a given IP address will
Leased Time 0-864000
be valid.

64
G.SHDSL Router – WS5300-4port Version 2.0

WAN

To setup VC configuration,
- Click submenu channel 1 to channel 12 for an appropriate VC, i.e ‘channel1’ for VC 1,
‘channel2’ for VC 2...
-
To Delete VC configuration,
- Click submenu channel 1 to channel 12 for an appropriate VC, then click button “Delete
VC …”

In menu WAN Setup, it shows the list of Virtual Circuits (VCs):channel 1 to channel 12

If a VC is already configured then it display its parameters as ISP Name, VPI,VCI, and so on.

If the VC is already activated, then in the field ‘Active’, it displays the word ‘Yes’, otherwise it
displays a ‘No’.

If the VC set with the encapsulation type of PPPoE or PPPoA, then in the field Encapsulation it
displays the status of PPP connection: RFC2684,IpoA, PPPoE or PPPoA

65
G.SHDSL Router – WS5300-4port Version 2.0

The details of the items are described in the following table:

Item Field Name Description Value

ISP Name ISP Name Max. 18 characters

VPI Virtual Path Identifier, given by ISP 0 - 16

VCI Virtual Channel Identifier, given by ISP 33 - 4096

RFC2684 / IPoA /
The encapsulation type is given by ISP. PPPoE / PPPoA
Encapsulation
Select from the drop-down list.
Default: PPPoA
Header to identify the protocol that
Virtual Circuit being carrying.
LLC / VCMUX
Multiplex LLC: Logical Link Control Multiplexing
Default: LLC
VCMUX : VC-based Multiplexing
Select from the drop-down list..
Quality of Services
UBR: Unspecified Bit Rate. UBR / CBR / rt-VBR /
CBR: Constant Bit Rate. nrt-VBR
QoS rt-VBR: Real-Time Variable Bit Rate. Default: UBR
nrt-VBR: Non-Real-Time Variable Bit
Rate.
Select from the drop-down list.
Peak Cell Rate
The maximum transmission rate. 0 - 5424
VC1 (PCR)
Sustained Cell
The Transmission rate in a burst traffic. 0 - PCR
Rate (SCR)
Maximum Burst Maximum number of transmission cell at
0 - 1000
Size (MBS) the peak rate.
Dynamic IP Disable/Enable
Enable or Disable Dynamic IP Address
Address Default: Disable
Disable/Enable
IP Un-numbered Enable or Disable IP Un-numbered
Default: Disable
The WAN local IP Address of router,
WAN IP Address i.e ‘123.221.79.2’
given by ISP
WAN IP Subnet The WAN local IP subnet mask of router,
i.e ‘255.0.0.0’
Mask given by ISP
Remote IP Address The IP Address of DSLAM, given by ISP i.e ‘229.122.79.32’
ISP login user name, given by ISP. It is
User Name set for the encapsulation type of PPPoE Max.30 characters
or PPPoA
ISP login password, given by ISP. It is
Password set for the encapsulation type of PPPoE Max.30 characters
or PPPoA
IP Sharing or NAT (Network Access
Disable/Enable
IP Sharing Translation). Select from the drop-down
Default: Disable
list.

66
G.SHDSL Router – WS5300-4port Version 2.0

4.3.4.3 Advanced Configuration

In menu “Advance Configuration”, the system can be configured in the submenu Routing, SNMP,
Virtual Server, DMZ ,VPN, WAN-DHCP Relay and Access List

Routing

The details of the items are described in the following table:

Item Field Name Description Value

With Dynamic Routing, you can enable WS5300- Disable /
4port to automatically adjust to physical changes in Enable
RIP
the network’s topology. Default:
Dynamic
Enable or disable the Routing Information Protocol. Disable
Routing
RIP version determines the format and broadcasting RIP-1 / RIP-2
Version method of any RIP transmissions by the WS5300- Default: RIP-
4port. 2
A static route is a pre-configured path that data must
traverse to reach a specific host or network. i.e ’10.10.10.
IP Address
Specify the Destination IP Address for entry in the 50’
static routing table.
Static
i.e
Routing Specify the Subnet Mask for the network configured
IP Subnet Mask ‘255.255.255.
in the static routing table.
0’
i.e ’192.168.0
Gateway Specify the IP address of Gateway.
.1’

SNMP

67
G.SHDSL Router – WS5300-4port Version 2.0

To configure the SNMP, go through the following steps.

„ Click the button to Enable or Disable SNMP management capabilities.

„
Community

Read-Only Community:
„ Specify the community name of external SNMP Managers allowed with access level of
“ Read “ to the unit’s MIB..
„
Read-Write Community:
„ Specify the community name of external SNMP Managers allowed with access level of
“ Read & write “ to the unit’s MIB.

Trap
To configure the Trap, go through the following steps.

„ Select the version number, SNMPv1 or SNMPv2, from the pull-down menu.
„ Specify the IP address of each SNMP Trap Manager in the correspondent Destination IP.
„ Select the options, None, Add or Delete, from the pull-down menu.
„ Click the “ Apply “ button to save the configuration.

68
G.SHDSL Router – WS5300-4port Version 2.0

Virtual Server

To configure, go through the following steps.

„ Specify the IP address of the correspondent local server, e.g., Web, FTP or Telnet.
„ Check the button to Enable these servers.
„ Specify the name of the application.
„ Specify the starting global port number as Port Start indicated.
„ Specify the starting global port number as Port End indicated.
„ Select the protocol, TCP or UDP passing through this port from the pull-down menu. .
„ Specify the WAN channel number.
„ Specify the IP address of the local server at which the Internet user is accessible.

Check the button to Enable it.

69
G.SHDSL Router – WS5300-4port Version 2.0

DMZ

Click DMZ from the Configuration menu item for showing the configuration screen.
To configure,

„ Specify the WAN channel number.

„ Specify IP address of the DMZ host intended for.
„ Check the button to Enable or Disable it.

Click the Apply button to save the configuration.

70
G.SHDSL Router – WS5300-4port Version 2.0

VPN

Click VPN from the Configuration menu item for showing the configuration screen.
To configure,

„ Click the button to Enable or Disable the tunnel pass through feature specific to IPSec,
L2TP, or PPTP corresponding to each protocol.

Click the Apply button to save the configuration.

71
G.SHDSL Router – WS5300-4port Version 2.0

WAN DHCP-Relay

72
G.SHDSL Router – WS5300-4port Version 2.0

Access List

Standard Access Control List

73
G.SHDSL Router – WS5300-4port Version 2.0

Extended Access Control List – IP filtering

74
G.SHDSL Router – WS5300-4port Version 2.0

DOS Protection

75
G.SHDSL Router – WS5300-4port Version 2.0

4.4 Maintenance

4.4.1 General Maintenance

From menu item “Admin”, you can get the “General Maintenance” menu.

To configure Password,

„ Check the button “ Yes “ to confirm the change or “ No “ to nullify the action.
„ Enter the Old Password used.
„ Enter the New Password desired.
„ Re-enter the New Password to confirm the change.

Click the “ Apply “ button to save the configuration.

4.4.2 Time Settings

76
G.SHDSL Router – WS5300-4port Version 2.0

The details of the items see section 3.5.5

4.4.3 Factory Default

From Factory Default Menu, you’ll get a dialog as following picture:

If you click “OK” to re-load factory default, the device will reboot by itself.

77
G.SHDSL Router – WS5300-4port Version 2.0

4.4.4 Save

If you click “OK” to save the new configuration, the device will reboot by itself.

4.5 Performance

4.5.1 DSL Performance & Statistic

Display the DSL Performance and Statistics.

78
G.SHDSL Router – WS5300-4port Version 2.0

4.5.2 ATM Performance & Statistic

Displaying ATM Performance and Statistics.

79
G.SHDSL Router – WS5300-4port Version 2.0

5. Upgrading Firmware

There are 2 kinds of methods to update firmware:

- Through Serial port
- Through Ethernet port

5.1 Upgrade using Ethernet port

Step 1:Install TFTP software, such as TFTP Client (Details see Appendix A).
Step 2:Connect the RS-232 & Ethernet cable to PC and GDTU-204
Step 3:Using Hyper Terminal of Windows to check GDTU-204 status.The default setting of Hyper
terminal is 115200 bps, 8 data bit, No Parity, 1 stop bit.
Step 4:Check the IP address of GDTU-204, to make sure it is on the same subnet with your PC
(e.g. PC-192.168.2.10, GDTU-204-192.168.2.105)
Step 5. Do ping test from your PC, to make sure the connection between PC and GDTU-204 unit
is good.
Step 6:Run the TFTP Client software under the Windows's XP or 2000 OS, to get following
screen:

Step 7:Click ‘Settings‘ button, to get following screen, and choose the “Timeout” checkbox
(dfault value is 3 seconds), then click “OK”.

80
G.SHDSL Router – WS5300-4port Version 2.0

Items Description
TFTP server : Enter the IP Address of TFTP Server(GDTU-204’s IP).
Operation : Click the check box for “ Upload “.
Format : Select binary for file format.
Local file name : Specify the targeted file through directory and path associated.
Upload Now --- : Click this button to proceed the update.
Settings : Specify the Local folder , Block size and Timeout

Step 7:Click “Upload Now…” to upgrade firmware.Code in GDTU-204 will be upgraded after
several minutes, and automatically reboot device.

5.2 Upgrade using Serial port

Step 1:Connect PC and GDTU-204 with RS-232 cable.

Step 2:Using Hyper Terminal of Windows to check GDTU-204 status.The default setting of Hyper
terminal is 115200 bps, 8 data bit, No Parity, 1 stop bit.
Step 3:Power on the GDTU-204, then PC will show following screen

81
G.SHDSL Router – WS5300-4port Version 2.0

82
G.SHDSL Router – WS5300-4port Version 2.0

Step 3: Press “Enter” key immediately when you see this message “Hit any key to stop autoboot:
“ then you can see the prompt “=>”. Enter “loadb 100000” and press “Enter” key you can get
following screen

Step 4: Select “Send File…” under the tool’s bar of “Transfer” as following screen.

83
G.SHDSL Router – WS5300-4port Version 2.0

Step 5: Then you can get the following screen:

Step 6: Select “Kermit” Protocol as the following screen:

84
G.SHDSL Router – WS5300-4port Version 2.0

Step 7: Click “Browse” for select file to send as the following screen:

Step 8: Click “OPEN”, you can get the following screen:

85
G.SHDSL Router – WS5300-4port Version 2.0

Step 9: Click “Send” you can get the following screen:

Step 10: Code in GDTU-204 will be uploaded. It will take about 18~20 minutes. The above
screen will automatically disappear after Code was completely updated and you can get the
following screen:

86
G.SHDSL Router – WS5300-4port Version 2.0

Step 11: Enter “erase 2860000 2bfffff “ as the following screen:

Step 12: It will take about few minutes to erase flash memory and the screen will display “done”
message as the following:

87
G.SHDSL Router – WS5300-4port Version 2.0

Step 13: Enter “cp.b 100000 2860000 $(filesize)” as the following screen:

Step 14: It will take about few minutes to copy flash memory and the screen will display “done”
message as the following:

88
G.SHDSL Router – WS5300-4port Version 2.0

Step 15: Enter “reset “ as the following screen:

89
G.SHDSL Router – WS5300-4port Version 2.0

Appendix

Appendix A:Install TFTP software

Step 1:Install the software of TFTP, double click the icon of tptpd_ftp.exe as following:

Step 2:Then the PC will show installing icon as following:

90
G.SHDSL Router – WS5300-4port Version 2.0

Step 3:Click “Next”, the PC will show following screen

Step 4: Select “I agree to the terms of this license agreement.” and click “Next” to get following
screen:

91
G.SHDSL Router – WS5300-4port Version 2.0

Step 5: Click “Next” and to get following screen:

Step 6: Click “Next” and to get following screen:

92
G.SHDSL Router – WS5300-4port Version 2.0

Step 7: Click “Install” and to get following screen:

Step 8: Then click “Finish”, The TFTP software has been installed completely.

93