For LED TV ES7000 Series

UE40ES7000
UE46ES7000
UE55ES7000
UE40ES7500(CIS)
UE46ES7500(CIS)
UE55ES7500(CIS)
 index

I. Product Concept
II. UES7000 Overview
III. Inside of UES7000
IV. Main board
V. New Function of UES7000
VI. Disassembly and Reassembly
VII. Change IR
VIII. Cables
IX. Troubleshooting
Product Concept

SAMSUNG
Ⅰ. Product Concept
“Voice/Gesture Control, Face Recognition SI, New Experience NEW Smart TV” (ES7000)
- SI (Smart Interactive) : Quick approch to menu and service by voice control. Direct navigation by
Gesture control

“New Experience(SI), ’12 TV New Design Trend’s New Concept Premium Design, and
Support world best picture quality. High-end Smart TV” (ES8000)
- Design : Flower Petal look Metallic Design (Detailed Premium design)
Curved line Stand: ’12 New Trend of TV Design
- Picture Quality (Micro Dimming Ultimate) : By 576 block’s detaild picture control,
Support world best clear quality

■ External Value Curve ■ Strategic Positioning

Premium
Sony HX929 D8000 ES8000
ES8000
ES7000

HX929 D8000
D7000

SONY

Technology Emotional

Cost Picture Sound Design New Userability

Quality Experience
Basic
UES7000 Overview

SAMSUNG
UE8Y Overview
Spec Comparison to the Old Models
Model UES7000 UD7000

Design

Diplay Type LED TV LED TV

Built-in Tuner O O
Resolution 1920 x 1080 1920 x 1080
LCD Panel TFT LCD Panel 240Hz TFT LCD Panel 240Hz
Screen Size 40"/46"/55" 40"/46"/55"
Picture ratio 16:9 16:9
914.4 * 611.2 * 241.3 mm with stand 40": 908.6 X 29.7 X 524.9 mm with stand
914.4 * 545.7 * 29.7 mm without stand 908.6 X 241.3 X 600 mm without stand
46": 1046.8*691.2*276.7 mm with stand 46": 1041.1 X 29.7 X 599.4 mm with stand
Dimensions(W x H x D)
1046.8*620.2*29.7 mm without stand 1041.1 X 276.5 X 607.5 mm without stand
55": 1238.4*790.4*276.7 mm with stand 55": 1232.6 X 29.7 X 707.2 mm with stand
1238.4*728*29.7 mm without stand 1232.6 X 309.3 X 789.7 mm without stand
40” : 9.55kg_without stand 40” : 10.0kg_without stand
11.8kg_with stand 12.0kg_with stand
46” : 11.98kg_without stand 46” : 12.4kg_without stand
Weight
14.6kg_with stand 14.3kg_with stand
55” : 16.6kg_without stand 55” : 16.2kg_without stand
19.3kg_with stand 18.6kg_with stand
Contrast Ratio MEGA CR MEGA CR
Picture Enhancer 3D HyperReal Engine 3D HyperReal Engine
Equalizer 5 Band 5 Band
Auto Volume Control O O
Surround Sound Dolby Digital Plus / Dolby Pulse, DNSe Dolby Digital Plus/Pulse
40"/ 46": 10W + 10W
Speaker Output 10W + 10W
55"/65" : 15W +15W
PIP O O
Double Window X X
Caption O O
Entertainment Mode X X
Game Mode O O
Energy Saving O O
Anynet+ O O
Antenna 1(Cable/Air/Satellite) 1(Cable/Air/Satellite)
UE8Y Overview

UES7000 Key parts

- 1080P FULL HD
- 3HDMI, HDMI CEC support
- 240Hz Auto Motion Plus
- All Share Play
- Smart Hub (Full browser, Media play)
- Built–in Wifi
- Motion Control & Voice Contol
- Built-in Camera
- 3D
- Smart Control
-IR Blaster

UES7000

- Vesel: Super Narrow Bezel (Factory Option: U-MOIP-7K)

- Panel: 40”,46”,55”, Super Clear
- memory: 2G
- power consumtion: 40”: 135W / 46”: 150W / 55”:160W/Standby <0.1W
UE8Y Overview
Control & Connection Panel
Eco sensor

Remote sensor : light up

UE8Y Overview
Remote controller
UE8Y Overview
Remote controller
UE8Y Overview
Remote controller
UE8Y Overview
Accessories
UE8Y Overview
Accessories
UE8Y Overview
Accessories
Inside of UE8Y

Inside of UES7000
SAMSUNG
Inside of UE8Y
Inner Feature of UE8Y
IP board, Main board, Panel

MoiP(IR)
Power Board
MoiP Cable

Main board

LVDS Cable

T-CON

Speaker(R) Speaker(L)
Inside of UE8Y
Wiring Diagram of UE8Y

CNM803

CN8015

CON3
Main Board
SAMSUNG
Explanation of Main board
Main board LAYOUT

USB3

Please show
USB2
Moip
bottom of board
OPTICAL (move photo up or
IC1202 CN201
make smaller)
USB1
IC Video Power
process

HDMI3

IC801
HDMI2 CN1601
IC Video
decoder LVDS

HDMI1 CN1201
Function
PC sound & LED
Deco

H/P
CN301
Speaker
EXT1

RF(S2) Component
LAN

RF
UK/Nordic:
T2/C
EU: T/C
FRONT BACK
Explanation of Main board
ECHO--P/ECHO
ECHO P/ECHO--A Block Diagram
DAC
OUT DDR3 I/F DDR3-1866
TMDS 256MB x4
HDMI 800/933MHZ
Max : 300MHz
4x1 SW OD : 1066MHz
SIL9587
eMMC4.41 eMMC4.41
2GB
Echo-P USB1/2/3

USB 2.0 USB SW

CI • 2 X Cortex-A9 4X1
T-con b’d
(@1GHz)
• 32/32/1M Echo-Fp Echo-T
• eMMC4.41 DEBUG UART Debug LVDS
. 240 FRC
• DDR3-2133 MAX3222
TS . 3D . 240 T-con
• 2MFD
SIF_I2S RMII
NIM Tuner • H.264 (720p) Ethernet LAN
Encoder RTL8201F DDR3
DDR3 Flash
128MB
128MB
• HDMI 1.4 TX Optical
300MHz
RF CVBS
LVDS 2ch LVDS SW
LVDS 2ch
DTV_CVBS SD VIDEO 13bit DS90LV804
X3
HD VIDEO 33bit Main_check

Smart
AV2 In

SC1 CVBS
UART Sub Micom
WT61P806
UART
Evolution
Echo-A
RF_CVBS USB 2.0
USB SW
USB2.0
Kit
Scart1_LR • CVBS AFE 2:4 USB2.0
Scart RGB • 3channel
Bluetooth
AFE
• Audio Interrupt USB Hub Wi-fi
Codec 4X1
Component I2C
IIC MOIP
or AV1 Buffer
Comp/AV_LR SPDIF
AV1 CVBS PCM_I2S I2S
YPbPr SC1_I2S I2S_Tx0_SDO
0
Mon./HP_I2S I2S_Tx1_SDO Speaker
1/2 I2S_TX1_SDO 0 Speaker A5V
AMP
Line out (미주)
24bit Line out / Headphone TAS5735
PC/DVI_LR 96KHz Headphone (구주)
PC/DVI Audio DAC 2 WOV
24bit Scart 1 Audio AMPScart 1 (구주)
96KHz
DAC 1 2V RMS
B13V
24bit
96KHz
DAC 3
New Function of
UES7000
SAMSUNG
New Function of UE8Y

Motion Control

2. Indicate a menu about CH, VOL in Screen

1. Shake your hand in front of TV

5. If your hand let down on the screen, 4. Grabbing hand is a Click. 3. Move a cursor by using hand gesture, move a
the manu will be a close (If you maintain hand grabbed, TV execute cursor to Chanel up area
channel up consecutively
New Function of UE8Y

Voice Control

Chanel up

채널 올려

Hi TV 2. Control CH by command “Channel

up/down”

Volume down
1. Show a Voice cognition Menu by command “Hi TV”

볼륨 내려

3. Control Volume by command

“Volume up/down”
New Function of UE8Y
Limitation of Voice control and Gesture Control
New Function of UE8Y

Smart Control
New Function of UE8Y
IR Bluster
Legacy Device Main TV

1 Push SMART touch control Key

- Key Data sending to TV (Bluetooth)

2 TV  IR Bluster, Key Data Transfer IR

- Bluetooth 2
3 BT
BT
3 External Device control
- IR Bluster  Device, IR commend Send 1

IR IR Bluster
SMART
Touch
Control
2
6
New Function of UE8Y
HID Connection Sold Saparately,
Support models are below.

Item Maker Model No

Keyboard+Mouse SRP-9100B
Samsung
Keyboard SRK-5000UB
MK550
MK520
Keyboard+Mouse
MK320
MK260
K750
Logitech
K400
K360
Keyboard
K350
K340
K320
SMO-3500B
Mouse Samsung
Wired or wireless SMO-3200B
V220
connection M510
M505
M325
Mouse Logitech M310
M305
M235
M215
M185
Wireless Mobile Mouse
6000
Wireless Mouse 5000
Wireless Mobile Mouse
4000
Wireless Mobile Mouse
Mouse Microsoft 3500
Wireless Mobile Mouse
3000
Wireless Mouse 1000
Explorer Mini Mouse
Arc Mouse
New Function of UE8Y
AllShare Play

AllShare Play lets you access, view,

or play photos, videos, or music
located on USB devices, digital
cameras, cell phones, and PCs.
PCs, cell phones, and other
compatible devices can be accessed
wirelessly, through your wireless
network.
(Enjoy photos, music and/or movie
files saved on a USB Mass Storage
Class (MSC) device and/or your PC.)
New Function of UE8Y
Evolution Kit ( Sold Separately)

This socket is designed to accept an exten

sion device called Evolution Kit. The Evolut
ion Kit enables the TV to run a variety of th
e latest applications for a better user experi
ence.
The Evolution Kit, which may not be availa
ble depending on the product, will be sold s
eparately in 2013 or later.
Disassembly and Reassembly

Disassembly
and
Reassembly
SAMSUNG
Disassembly and Reassembly
Disassembly and Reassembly
Disassembly and Reassembly
Disassembly and Reassembly
Disassembly and Reassembly
Disassembly and Reassembly

Change IR

SAMSUNG
Cables
SAMSUNG
Troubleshooting
SAMSUNG
Troubleshooting
Service Mode
1. Check the various cable connections first.
• Check to see if there is a burnt or damaged cable.
• Check to see if there is a disconnected or loose cable connection.
• Check to see if the cables are connected according to the connection diagram.
2. Check the power input to the Main Board.
3. How to distinguish if the problem is caused by Main board or T-Con
a. No Video : If the problem is No Video but BLU is on and Indication
LED is blinking repeatedly and faster than nomal booting, replace the T-Con board.
b. Distorted Picture : Check the inner patterns.

*How to check inner pattern?

1.Factory mode(mute -> 1 -> 8 -> 2 -> Power on when TV is in ‘stand-by mode’)
2. Move to SVC menu
3. Move to Test Pattern
4. Check inner patterns. (This model only support FBE, READ PRE, READ POST)
Troubleshooting
Troubleshooting
No Video

No video?

Check LCD Panel

Check TCON input 12V & clock

BLU ON/OFF ? Yes

On 12V & clock OK?

Off No
Check Main Board 12V output
Check SMPS, IP

Yes Check TCON DCDC output Voltage

12V & clock OK?
No

Yes
OK ?
Check SMPS, Main Board Check Cable, CNT No

T-con faulty LCD Panel faulty

Troubleshooting
Picture Quality Problems

Problem Solution
. First of all, please perform the Picture Test and confirm that your TV is properly displaying test image. (Go to Menu → Support → Self Diagnosis → Picture
Test) If the test image is properly displayed, the poor picture may caused by the source or signal.

. If you have an analogue cable / set top box, upgrade to a digital set top box. Use HDMI or Component cables to deliver HD
(high definition) picture quality.
● The TV image does not . Cable / Satellite subscribers: Try HD stations from the channel line up.
look as good as it did in the . Aerial connection: Try HD stations after performing Auto programme.
store. - Many HD channels are up scaled from SD(Standard Definition) contents.
. Adjust the Cable/Set top box video output resolution to 1080i or 720p.
. Make sure you are watching TV at the minimum recommended distance based on the size and definition of the signal.
. Compression of video contents may cause picture distortion especially in fast moving pictures such as sports and action
● The picture is distorted:
movies.
macro block error, small
. Low signal level or bad quality can cause picture distortion. This is not a TV issue.
block, dots, pixelization
. Mobile phones used close to the TV (cca up to 1m) may cause noise in picture on analogue and digital TV.
. If you’re using a component connection, make sure the component cables are connected to the correct jacks. Incorrect or
● Colour is wrong or missing. loose connections may cause colour problems or a blank screen.
. Adjust the Picture options in the TV menu (go to Picture / Colour / Brightness / Sharpness)
● There is poor colour or . Adjust Energy Saving option in the TV menu (go to Menu → System → Eco Solution → Energy Saving)
brightness. . Try resetting the picture to view the default picture settings (go to Menu → Picture → Reset Picture)
● There is a dotted line on . If the picture size is set to Screen Fit, change it to 16:09.
the edge of the screen. . Change cable / satellite box resolution.
● The picture is black and . If you are using an AV composite input, connect the video cable (yellow) to the Green jack of component input 1 on the TV.
white.
● When changing channels,
. If your TV connected with a cable / set-top box, reconnect the AC cord and wait until the cable / set-top box reboots.
the picture freezes or is
. Set the output resolution of the cable box to 1080i or 720p.
distorted or delayed.
Troubleshooting
Sound Quality Problems

Problem Solution
. First of all, please perform the Sound Test to confirm that your TV audio is properly operating. (Go to Menu →Support → Self Diagnosis → Sound Test)
If the audio is OK, the sound problem may caused by the source or signal.

● There is no sound or the

sound is too low at maximum Please check the volume the of external device connected to your TV.
volume.
. Set the Speaker Select option to TV Speaker in the sound menu.
● The picture is good but . If you are using an external device, make sure the audio cables are connected to the correct audio input jacks on the TV.
there is no sound. . If you are using an external device, check the device’s audio output option (ex. you may need to change your cable box’s
audio option
. Check the cable connections. Makesure a video cable is not connected
to an audio input.
● The speakers are making . For aerial or cable connections,
an inappropriate noise. check the signal strength. Low signal
level may cause sound distortion.
Troubleshooting
No Picture / No video Problems

Problem Solution
. Make sure the AC power cord is securely plugged in to the wall outlet and the TV.
● The TV won’t turn on.
. Make sure the wall outlet is working.

. Ensure the Sleep Timer is set to Off in the Setup menu.

● The TV turns off . If your PC is connected to the TV, check your PC power settings.
automatically. . Make sure the AC power cord is plugged in securely to the wall outlet and the TV.
. When watching TV from an aerial or cable connection, the TV will turn off after 10~15 minutes if there is no signal.
. Check cable connections (remove and reconnect all cables connected to the TV and external devices).
. Set your external devices’ (Cable / Set top Box, DVD, Blu-ray etc) video outputs to match the connections to the TV input.
● There is no picture/Video. For example, if an external device’s output is HDMI, it should be connected to an HDMI input on the TV.
. Make sure your connected devices are powered on.
. Be sure to select the TV’s correct source by select Source using your remote.
● This file may not be . This may appear because of high bit rate of content. Content generally will play but could experience some playability issue.
playable properly.
Troubleshooting
RF (Cable/Aerial) Connection Problems

Problem Solution
•• Make sure the coaxial cable is connected securely.
The TV is not receiving all •• Please try Auto Program to add available channels to the channel list. Go to MENU - Channel - Auto Program then select
channels. Auto and make surethe correct Cable TV signal type is set in the menu. There are 3 options (STD, HRC and IRC)
•• Verify the Antenna is positioned correctly.
•• Check Caption Setup menu. Try changing Caption Mode Service1 to CC1.
No Caption on digital •• Some channels may not have caption data.
channels

The picture is distorted:

•• Compression of video contents may cause picture distortion, especially
macro
with fast moving pictures such as sports and action movies.
block error, small block, dots,
•• A low signal can cause picture distortion. This is not a TV problem.
pixelization.
Troubleshooting
PC Connection Problems

Problem Solution
“PC” is always shown on the •• This is normal; “PC” is always shown on the source list, regardless of whether a PC is connected.
source list,
even if a PC is not connected.

The video is OK but there is

•• If you are using an HDMI connection, check the audio output setting on your PC.
no audio.
Troubleshooting
Other Problems

Problem Solution
•• HD channels will have black bars on either side of the screen when displaying up scaled SD (4:3) contents.
The picture won’t display in •• Black bars on the Top & Bottom will be shown on movies that have aspect ratios different from your TV.
full screen. •• Adjust the picture size options on your external device or TV to full screen.

•• Caption can not be selected in the TV menu when connected via HDMI or Component.
Caption on TV menu is •• Caption must be activated on the external device.
greyed out.

•• This smell is normal and will dissipate over time.

There is a plastic smell from
the TV.
The TV Signal Information is •• This function is only available with digital channels from an Antenna / RF / Coax connection.
unavailable in the Self
Diagnostic
Test menu.
The TV is tilted to the side. •• Remove the base stand from the TV and reassemble it.
The channel menu is greyed •• The Channel menu is only available when the TV source is selected.
out
(unavailable).
Your settings are lost after 30 •• If the TV is in the Store Demo mode, it will reset audio and picture settings every 30 minutes.
minutes or every time the TV Change the settings from Store Demo mode to Home Use mode in the Plug & Play procedure.
is Press the SOURCE button to select TV mode, and go to MENU → System → Plug & Play → ENTER
turned off.
•• Check the cable connections and reconnect them.
You have intermittent loss of •• Loss of audio or video can be caused by using overly rigid or thick cables.
audio or video. Make sure the cables are flexible enough for long term use. If mounting the TV to a wall,
we recommend using cables with 90 degree connectors.
You see small particles when •• This is part of the product’s design and is not a defect.
you look closely at the edge
of
the frame of the TV.
Troubleshooting
Other Problems

Problem Solution
•• Select Home Use under Plug & Play mode. For details, refer to Plug & Play Feature.
POP (TV’s internal banner ad)
appears on the screen.

Melody is not played when television is If the Volume is Mute or set to Volume level 0 or Melody mode is off, or in the case of automatic power off
turned off. due to the 'Sleep timer' function, then no melody will be played at power off.

When the channel is changed, volume

It takes about 2 seconds to adapt to volume levels on different channels.
gradually gets louder.

Even if I change sound mode, monitor out The monitor out sound is independent from the main sound output, therefore changes to the audio output will
sound is constant. not affect the monitor output.

Even if I set mute on, monitor out is still The monitor out sound is independent from the main Speaker output, therefore to Mute or adjust the volume
outputting. of monitor out a separate external decoder (AMP) is required.
The volume buttons and MUTE buttons do not operate when the Speaker Select is
I set Mute on but sound is still outputting.
set to External Speaker. Please set the volume on your Home theater.
■ Speaker Settings
● Speaker Select (External Speaker / TV Speaker)
A sound echo may occur due to a difference in decoding speed between
the main speaker and the audio receiver. In this case, set the TV to External Speaker.
☞When Speaker Select is set to External Speaker, the volume and MUTE buttons
will not operate and the sound settings will be limited.
☞When Speaker Select is set to External Speaker.
● TV Speaker: Off, External Speaker: On
☞When Speaker Select is set to TV Speaker.
● TV Speaker: On, External Speaker: On
☞If there is no video signal, both speakers will be mute.
There is a vertical line(red,green,blue) on This occurs when TV set has a defect on one line from DATA SOURCE DRIVER IC. Contact Samsung
picture. Service centre to resolve this problem.
Troubleshooting
Other Problems

Problem Solution
I can not hear any sound from speaker in If the input signal is DVI RGB signal through an HDMI conversion cable, there is no digital sound data, you
HDMI mode when using a DVI-HDMI can not hear any sound. A DVI connection does not carry any sound data. You should connect an audio cable
conversion cable. to the appropriate input jack for a seperate audio channel.

The HD caption that appears when switching channels or when pressing the Information button on the remote
Although the TV caption shows HD, the
control means the selected channel is simply a digital channel. If the broadcasting station converts an analog
visual quality is not satisfactory.
signal into digital and transmits the signal, the visual quality may not be perfect.
The visual qualities of digital channels may vary depending on the original production method(analog or
digital)
→ Grouping displayed information when switching channels.
The visual qualities of digital channels vary
→ If the original production method is digital: High visual quality program.
→ If the original production method is analog: The digital program displayed on the screen is originally
an analog program which has been converted. The visual quality is of an SD grade.

HDMI Black Level does not work on HDMI This function is active only when the an external device
device that is output by YCbCr. (DVD player, STB etc.) is connected to the TV via HDMI(RGB Signal).

If you use external equipment that support low HDMI version, sound may not be output at TV that support
new HDMI version(HDMI1.3).
There is no sound when using HDMI mode.
→ If sound does not work, use HDMI2 IN for video input and DVI IN(HDMI1) port[R(red) - AUDIO - L(white)]
for audio input.
Troubleshooting

Supported Multi Media format(photo, music, video)

Video Decoder Audio codec

• Supports up to H.264, Level 4.1 • WMA 10 Pro supports up to 5.1 channel. WMA lossless audio is
• H.264 FMO / ASO / RS, VC1 SP / MP / AP L4 and not supported.
AVCHD are not supported. • RealAudio 10 lossless is not supported.
• For all Video codecs except MVC, VP8, VP6: • QCELP, AMR NB/WB are not supported.
−− Below 1280 x 720: 60 frame max • If Vorbis is only in Webm container, supports up to 2 channel
−− Above 1280 x 720: 30 frame max
−− GMC 2 over is not supported.
• Supports only SVAF Top/Bottom and Side by Side.
• Supports only BD MVC Spec.
Troubleshooting

Supported Multi Media format(video)