Action 1: Determine The Scope of Problems

呼叫建立成功率Call Setup Success Rate
Required Steps Required Actions KPI 名称(Chinese Name)
Action 1: Determine the scope of problems

Determine whether call setup fail occurs on some top
呼叫建立成功率
Step1: Demarcati cells or the entire network.
if local formula is not the same with the one in D4,
please write donw in D5 like the demo 呼叫建立成功率--印度
Action 2.1:Alarm Checking
Alarm ID
7604
7606
7738
7767
Mandatory checking 7744
7745
7746
2725
7164
Except above, if other alarms exist, please list them

here
Action 2.2: Parameters Checking

参数名称
Paramter Name
maxNumberRetransmission
numberOfSlotsSpreadTrans
penaltyTime
temporaryOffset
cellReselectParamInd
cellBarQualify
cellBarred
Step2:Checking cellReselectOffset
cellReselectHysteresis
drInUse
drmethod
drThreshold
msTxPwrMax *GSM*dBm
msTxPwrMax *DCS*dBm
minMSTxPower *GSM*dBm
minMSTxPower *DCS*dBm
rxLevAccessMin
msTxPwrMaxCCH *GSM*dBm
msTxPwrMaxCCH *DCS*dBm
bsTxPwrMax *GSM*dBm
bsTxPwrMax *DCS*dBm
bsTxPwrMin
Action 2.3: Neighbor Cell Checking
Perform Neighbor Cell Checking by OMStar Neighbor Cell Checking and Analysis functions
Action 2.3: Feature Checking
Feature Name
AMR Capacity
(E)GPRS DL Power Control
Increased Dynamic SDCCH Capacity
OSC Half Rate with SAIC MS
Extended CCCH
Intelligent Selective Paging
Paging coordination in BSC
Flexible MCPA TX Power Pooling
STIRC
2G TRX Automatic Power Down
Action 3.1: Identify call fail causes
SD占用原因
TCH指配成功率=TCH占用成功次数/TCH请求次数*100%
SD指配成功率=SD占用成功次数/SD请求次数*100%
SDCCH掉话率
Action 3.2: Radio Enviroment Analysis
下行电平质量分布
Identify poor coverage or Interference Analysis
上行电平质量分布
上行弱覆盖比例
下行弱覆盖比例
(Cell Level) Coverage Analysis
TA分布
平均TA值
小区级下行0~4级质量占比
(Cell Level) Interference Analysis 小区级上行0~4级质量占比

小区级4~5级干扰比例
因为无线原因掉话
因为无线口切换原因掉话
因为Abis接口掉话
因为Abis接口切换掉话
因为A接口掉话
SDCCH DROP reason 因为A接口切换掉话
因为LAPD失败导致的掉话
因为BTS原因掉话
因为用户行为导致的掉话
因为BCSU重配导致掉话
Step3: Anylysis 因为网络重置导致的掉话
载频级掉话
载频级0~5级质量占比
TRX Level Coverage and Interference Analysis
载频级4~5级干扰占比
载频级分配失败次数
Action 3.3: Capacity Analysis
TCH拥塞率
TCH拥塞次数（不含切）
TCH拥塞次数（含切）
TCH话务量
TCH全速率话务
TCH半速率话务
每线话务量
数据业务等效话务量
SDCCH话务量
SDCCH拥塞次数
Action 3.4: Transmission Anaysis
不可用时长
一般误码秒
严重误码秒
Action 3.5: RF Tunnel Analysis
TCH配置信道数
TCH可用信道数
TCH可用率
SDCCH配置信道数
SDCCH可用信道数
SDCCH可用率
全速率可用信道数
半速率可用信道数
链路平衡
Step4: Escalate TAction 4.1:TT by Local Flow
Description
KPI Name(English Name) Counter/Formula Tables Name
100*(1-
Call Setup Success Rate p_nbsc_service
sum(call_setup_failure)/sum(setup_succ+call_setup_failure))
Call Setup Success Rate--india
Alarm Name Influence(Major,Medium,Minor) Meaning
BTS OPERATION DEGRADED Medium 0

TRX FAULTY Medium 0
BTS WITH NO TRANSACTIONS Major 0
BCCH MISSING Major 0
EXCESSIVE TCH INTERFERENCE Major 0
CHANNEL FAILURE RATE ABOVE Major 0
CH CONGESTION IN BTS ABOVE D Major 0
ADJACENT CELL IDENTIFIER CON Major 0
MASTER CLOCK UNIT HARDWARE Major 0
ABBREV Value Range Reference Val
RET (1,2,4,7) 4
SLO (3..12, 14, 16, 20, 25, 32, 50)TDMA 12
PET (20…640) sec 20
TEO (0…70 step 10)dB 0
PI (Y/N) Y
QUA (Y/N) N
BAR (Y/N) N
REO (0…126 step 2)dB 0
HYS (0…14,step 2dB)dB 10
DR (Y/N) Y
DRM (0~1) 1
DRT (-100~-47) -80
PMAX1 (5…43 step 2) *GSM*dBm 33
PMAX2 (0…36 step 2) *DCS*dBm 30
PMIN (5…43 step 2) *GSM*dBm 5
PMIN (0…36 step 2) *DCS*dBm 0
RXP (-110…-47)dBm -102~-98
TXP1 (5…43 step 2) *GSM*dBm 33
TXP2 (0…30 step 2) *DCS*dBm 30
PMAX1 (0…30 step 2)DB 0
PMAX2 (0…30 step 2)DB 0
PMIN (0…30 step 2)DB 20
g and Analysis functions
Feature's Meaning Adapted Scenario and Gain

The “Wideband AMR” (BSS20960) featureBy i providing good voice quality and increased communication capabilities, to accelerate the return of investment in G
The (E)GPRS Downlink (DL) Power Control•It reduces transmit power, which in turn helps in reducing the interference in the network, and hence the mobiles exp
•It helps in reducing BTS power consumption.
It is increased to a maximum of 24 chan for railway, subway, highway location area boundary, avoid SD congestion
Orthogonal subchannel (OSC) is a feature •The increased capacity per TRX reduces the energy consumption per user. This reduces the energy consumption re
•Increased
•It avoids the use of packet
need to addswitched
new sites,(PS)
as itservices is possible
maintains without
the coverage being
area constrained
in capacity by the access grant channel (A
extensions.
Extended CCCH" feature increases the CCCH •Due to the increased rate of success in paging,
The increase in paging capacity may be experienced as: calls are established faster.
Precise Paging feature enhances the signal•The •Fewer revenue is improved
and possibly largerwith
sitesmore
can established/served
be used calls.
With the introduction of the feature "Paging coordination
•Reduced Abis in BSC", the
signaling BSCinperforms
load CCCH CS paging coordination internally when in the network operation mode II (NOM II).
TRX
'在PS数据业务期间，用户也可以收到CSSend SDCCH
the paging message'BSC not only in the PCH channel is still the traditional PACCH channel joint paging to avoi
SEIZURES
The Flexi Multiradio BTS RF Module (FXxx•It increases the capacity of the BTS for a given coverage area without the need ofadditional Radio Frequency (RF) m
REASON/Sum(SUCC_SEIZ_TERM+SUCC_SEIZ_ORIG+SDCCH_LOC_UPD+SU
•It reduces the call drop rate in coverage limited networks.
CC_SDCCH_SMS_EST+SDCCH_CALL_RE_EST+SDCCH_EMERG_CALL)
STIRC is designed to cancel uplink interf to enhance the MOS value, reduce the words
SDCCH
When this SEIZURES
featureREASON:
is activated in the network, the operator can lower the network operating costs by reducing energy
2G automatic power down" feature introdu Successful SDCCH seizures for location updating：SDCCH_LOC_UPD
Successful SDCCH seizures for a mobile terminated call(MTC)：
100*(A.MS_TCH_SUCC_SEIZ_ASSIGN_CMPLT+B.BSC_I_TCH_TCH+B.BSC_
SUCC_SEIZ_TERM
I_SDCCH_TCH+B.MSC_I_TCH_TCH+B.MSC_I_SDCCH_TCH+B.CELL_TCH_T P_NBSC_RES_ACCE
SDCCH seizures reason ratio Successful SDCCH seizures for a mobile originating call(MOC).： Counters from
CH+B.CELL_SDCCH_TCH)/(A.TCH_CALL_REQ- SS
table(s): from
SUCC_SEIZ_ORIG
A.A_IF_CRC_MISMATCH_CALL_SETUP+B.MSC_I_TCH_TCH_AT+B.MSC_I_ Counters
TCH Assignment Success Rate The number of successful SMS establishments on the
100*SUM(A.SDCCH_ASSIGN+B.MSC_I_SDCCH+B.BSC_I_SDCCH+B.CELL_SSDCCH: A=P_NBSC_TRAFFI
SDCCH_TCH_AT+B.BSC_I_TCH_TCH_AT+B.BSC_I_SDCCH_TCH_AT+B.CELL table(s): C
SUCC_SDCCH_SMS_EST
DCCH)
_TCH_TCH_AT+B.CELL_SDCCH_TCH_AT+A.TCH_FAST_REQ- A=P_NBSC_TRAFFI
SDCCH Assignment Success Rate 100*(A.SDCCH_RADIO_FAIL+A.SDCCH_RF_OLD_HO+A.SDCCH_A_IF_FAIL Counters
B=P_NBSC_HOfrom
The number of successful SDCCH seizures for call reestablishment：
/SUM(C.SDCCH_REQ+B.MSC_I_SDCCH_AT+B.BSC_I_SDCCH_AT+B.CELL_S
B.MSC_O_SDCCH_TCH_AT+B.BSC_O_SDCCH_TCH_AT+B.CELL_SDCCH_T
_CALL+A.SDCCH_A_IF_FAIL_OLD+A.SDCCH_LAPD_FAIL+A.SDCCH_BTS_F C
table(s):
SDCCH Call Drop Rate SDCCH_CALL_RE_EST
DCCH_AT)
CH_AT)
AIL+A.SDCCH_USER_ACT+A.SDCCH_BCSU_RESET+A.SDCCH_NETW_ACT)/ B=P_NBSC_HO
A=P_NBSC_TRAFFI
The number of successful SDCCH seizures for an emergency call：
SUM(A.SDCCH_ASSIGN+B.MSC_I_SDCCH+B.BSC_I_SDCCH+B.CELL_SDCC C=P_NBSC_SERVICE
C
SDCCH_EMERG_CALL
H) B=P_NBSC_HO
Counters from
sum over a range (class_upper_range) table(s):
DL LEV & QUAL Distribute KPI
(freq_dl_qual0+freq_dl_qual1+freq_dl_qual2+freq_dl_qual3+freq_d Counters from
p_nbsc_rx_statisti
sum
l_qual4over a range (class_upper_range) table(s):
cs
UL LEV & QUAL Distribute KPI
(freq_ul_qual0+freq_ul_qual1+freq_ul_qual2+freq_ul_qual3+freq_u
+freq_dl_qual5+freq_dl_qual6+freq_dl_qual7)/ p_nbsc_rx_statisti
UL Weak coverage rate 100*(SUM(freq_ul_qual0+freq_ul_qual1+freq_ul_qual2+freq_ul_qu
l_qual4
sum over all ranges cs
P_NBSC_RX_ST
al3+freq_ul_qual4+freq_ul_qual5+freq_ul_qual6+freq_ul_qual7)
(freq_dl_qual0+freq_dl_qual1+freq_dl_qual2+freq_dl_qual3+freq_d ATISTICS
+freq_ul_qual5+freq_ul_qual6+freq_ul_qual7)/
DL Weak coverage rate 100*(SUM(freq_dl_qual0+freq_dl_qual1+freq_dl_qual2+freq_dl_qu
Where
sum
l_qual4over all ranges P_NBSC_RX_ST
al3+freq_dl_qual4+freq_dl_qual5+freq_dl_qual6+freq_dl_qual7) Counters
ATISTICSfrom
CLASS_UPPER_RANGE<=15)/SUM(freq_ul_qual0+freq_ul_qual1
(freq_ul_qual0+freq_ul_qual1+freq_ul_qual2+freq_ul_qual3+freq_u
+freq_dl_qual5+freq_dl_qual6+freq_dl_qual7)
TA:class_upper_range
WHERE table(s):
TA Distribution +freq_ul_qual2+freq_ul_qual3+freq_ul_qual4+freq_ul_qual5+freq_
l_qual4
TA=0
CLASS_UPPER_RANGE<=20)/SUM(freq_dl_qual0+freq_dl_qual1 p_nbsc_timing_ad
ul_qual6+freq_ul_qual7)
+freq_ul_qual5+freq_ul_qual6+freq_ul_qual7) p_nbsc_timing_ad
Ave TA distance ave_ms_bs_dist
TA=1
+freq_dl_qual2+freq_dl_qual3+freq_dl_qual4+freq_dl_qual5+freq_ vance
100*sum(freq_dl_qual0+freq_dl_qual1+freq_dl_qual2+freq_dl_qual vance
…….
dl_qual6+freq_dl_qual7) Counters from
3+freq_dl_qual4)/sum(freq_dl_qual0+freq_dl_qual1+freq_dl_qual2
DL HQI KPI TA=63
100*sum(freq_ul_qual0+freq_ul_qual1+freq_ul_qual2+freq_ul_qual table(s):
+freq_dl_qual3+freq_dl_qual4+freq_dl_qual5+freq_dl_qual6+freq_ Counters from
sum over a range (class_upper_range)
3+freq_ul_qual4)/sum(freq_ul_qual0+freq_ul_qual1+freq_ul_qual2 p_nbsc_rx_qual
UL HQI KPI dl_qual7) table(s):
(freq_reports)/
+freq_ul_qual3+freq_ul_qual4+freq_ul_qual5+freq_ul_qual6+freq_ Counters from
sum over all ranges p_nbsc_rx_qual
Interferences KPIs ul_qual7)
100*Sum(Ave_Idle_f_Tch_4/Res_Av_Denom7+Ave_Idle_h_Tch_4/ table(s):
(freq_reports)
Number of SDCCH transaction p_nbsc_res_avail
Number of SDCCH SDCCH_RADIO_FAIL
failures due to radiotransaction
failures due to radio
failure
failure of the former channel during SDCCH_RF_OLD_HO
an SDCCH-SDCCH
Number of SDCCH transaction failures SDCCH_ABIS_FAIL
or SDCCH-TCH
due
Number to Abis
of SDCCH handover
interface failure during
transaction a call
failures
due to Abis interface failure on the old SDCCH_ABIS_FAIL_OLD
channel during a SDCCHSDCCH or TCH-
Numberhandover
SDCCH of SDCCH transaction failures
due to A-interface failure during a call SDCCH_A_IF_FAIL
Number
attempt of SDCCH transaction failures Counters from
due to A-interface failure on the old
SDCCH_A_IF_FAIL_OLD table(s):
channel during an SDCCH-SDCCH or P_NBSC_TRAFFIC
SDCCH-TCH
Number handover
of SDCCH transaction failures SDCCH_LAPD_FAIL
due to LAPD failure
Number of SDCCH transaction failures SDCCH_BTS_FAIL
due to BTS failure
Number of SDCCH transaction failures SDCCH_USER_ACT
due to user actions
Number of SDCCH transaction failures SDCCH_BCSU_RESET
due to BCSU reset
Number of SDCCH transaction failures
due to radio network reconfiguration SDCCH_NETW_ACT
actions
TCH_fail_call_ho
sum(freq_ul_qual0+freq_ul_qual1+freq_ul_qual2
Drop call number in TRX p_nbsc_underlay
tch_radio_fail
+freq_ul_qual3+freq_ul_qual4+freq_ul_qual5)/sum(freq_ul_qual0+f
TRX Quality (AVE_FULL_TCH_IF4+AVE_HALF_TCH_IF4+AVE_FULL_TCH_I
req_ul_qual1+freq_ul_qual2+freq_ul_qual3+freq_ul_qual4+freq_ul_ p_nbsc_rx_qual
F5+AVE_HALF_TCH_IF5/AVE_FULL_TCH_IF1+AVE_HALF_TCH
qual5+
TRX interference _IF1+AVE_FULL_TCH_IF2+AVE_HALF_TCH_IF2+AVE_FULL_T
freq_ul_qual6+freq_ul_qual7) p_nbsc_underlay
CH_IF3+AVE_HALF_TCH_IF3+AVE_FULL_TCH_IF4+AVE_HALF P_NBSC_UNDERLA
CALL FAIL NUMBER IN TRX TCH_REQUEST-TCH_SUCC_SEIZ
_TCH_IF4+AVE_FULL_TCH_IF5+AVE_HALF_TCH_IF5） Y
100*[sum(a.tch_call_req-a.tch_norm_seiz)-sum(b.msc_o_sdcch_tch+
.bsc_o_sdcch_tch+b.cell_sdcch_tch)+sum(a.tch_succ_seiz_for_dir_acc)-
sum(a.tch_rej_due_req_ch_a_if_crc - Counters from
TCH Congestion ratio (b.bsc_i_unsucc_a_int_circ_type))]/[sum(a.tch_call_req) table(s):
a = p_nbsc_traffic
- sum(a.tch_rej_due_req_ch_a_if_crc-
(a.QUE_ALL_ASS_REQ_FAIL+a.QUE_NALL_ASS_REQ_FAIL- Counters from
b = p_nbsc_ho
(b.bsc_i_unsucc_a_int_circ_type+b.msc_controlled_in_ho+b.ho_unsucc
a.A_IF_CRC_MISMATCH_CALL_SETUP+a.REMOVAL_FROM_QUE_DUE_T table(s):
TCH Congestion num (not include handovO_DR)-
_a_int_circ_type))] a = p_nbsc_traffic
(b.MSC_O_SDCCH_TCH+b.BSC_O_SDCCH_TCH+b.CELL_SDCCH_TCH) b = p_nbsc_ho
TCH Congestion num (include handover) sum(TCH_REQ_REJ_LACK-TCH_REJ_DUE_REQ_CH_A_IF_CRC) p_nbsc_traffic
Average TCH traffic sum(ave_busy_tch / res_av_denom14) p_nbsc_res_avail
Average FTCH traffic AVE_TCH_BUSY_FULL p_nbsc_res_avail
Average HTCH traffic SUM(AVE_BUSY_TCH/RES_AV_DENOM14)/
AVE_TCH_BUSY_HALF p_nbsc_res_avail
(SUM(AVE_AVAIL_TCH_SUM/AVE_AVAIL_TCH_DEN)
AVE ERL PER CHANNEL +SUM(AVE_GPRS_CHANNELS_SUM/AVE_GPRS_CHANNELS_DEN)- p_nbsc_res_avail
SUM(AVE_PERMANENT_GPRS_CH_SUM/AVE_PERMANENT_GPRS_CH_D
AVE PS traffic AVE_BUSY_GPRS_CH_DL/AVE_BUSY_GPRS_CH_DEN
EN)) p_nbsc_packet_contr
Average SDCCH traffic (AVE_BUSY_SDCCH/RES_AV_DENOM15) P_NBSC_RES_AVAIL
SD CONGESTION NUM SDCCH_BUSY_ATT P_NBSC_TRAFFIC
Not available time NOT_AVAIL_TIME Counters from

table(s):
Error second ERR_SEC
P_NBSC_ET_BS
Serious error second ERR_SEC_SEVER C
(AVE_AVAIL_TCH_SUM/AVE_AVAIL_TCH_DEN)+
(AVE_GPRS_CHANNELS_SUM/AVE_GPRS_CHANNELS_DEN)-
TCH CONFIGURATION CHANNEL ((AVE_AVAIL_TCH_SUM/AVE_AVAIL_TCH_DEN)+ P_NBSC_RES_AVAIL
(AVE_PERMANENT_GPRS_CH_SUM/AVE_PERMANENT_GPR
(AVE_GPRS_CHANNELS_SUM/AVE_GPRS_CHANNELS_DEN)-
TCH AVALIBLE CHANNEL 100*[sum(ave_avail_TCH_sum/ave_avail_TCH_den+ave_GPRS_c P_NBSC_RES_AVAIL
S_CH_DEN)
(AVE_PERMANENT_GPRS_CH_SUM/AVE_PERMANENT_GPR
hannels_sum/ave_GPRS_channels_den)]/ Counters from table(s):
TCH Availability KPIs S_CH_DEN)+AVE_NON_AVAIL_TCH_TIMESLOT)
[sum(ave_avail_TCH_sum/ave_avail_TCH_den+ave_GPRS_chan
(AVE_SDCCH_SUB/RES_AV_DENOM3+AVE_NON_AVAIL_SDC p_nbsc_res_avail
SD CONFIGURATION CHANNEL nels_sum/ave_GPRS_channels_den+ave_non_avail_TCH)] P_NBSC_RES_AVAIL
CH)
SD AVALIBLE CHANNEL (AVE_SDCCH_SUB/RES_AV_DENOM3) P_NBSC_RES_AVAIL
SDCCH Availability KPIs 100*(AVE_SDCCH_SUB/RES_AV_DENOM3)/
(AVE_AVAIL_FULL_TCH/RES_AV_DENOM2)+
(ave_bs_power - ave_dl_sig_str) - (ave_ms_power - P_NBSC_RES_AVAIL
(AVE_SDCCH_SUB/RES_AV_DENOM3+AVE_NON_AVAIL_SDCCH)
(AVE_GPRS_CHANNELS_SUM/ AVE_GPRS_CHANNELS_DEN)-
ave_ul_sig_str)
Full rate available channel num p_nbsc_res_avail
(AVE_PERMANENT_GPRS_CH_SUM/
43 - 2*sum(ave_ms_power) / sum(power_denom1)
Half rate available channel num AVE_TCH_AVAIL_HALF
AVE_PERMANENT_GPRS_CH_DEN)
ave_ms_power, p_nbsc_res_avail
Counters from table(s):
LINK BALANCE 43 - 2*sum(ave_bs_power) / sum(power_denom2) p_nbsc_power
ave_bs_power,
sum(ave_dl_sig_str) / sum(power_denom3) - 110 ave_dl_sig_str,
sum(ave_ul_sig_str) / sum(power_denom4) - 110 ave_ul_sig_str,
Manual Written Item by the FL
Shotscree
Instruction Self-Check
Reference Value Operation Required Currnent Value n/Attachm
s Conclusion
ent
Judge Call
failure reason:
>99% TOPN cell or
Whole network TOPN Cell
if TOPN cell ,
then perform
action2
Shotscree
Self-Check(Existing
Instructions
or not?) n/Attachm
ent
Antenna alarm: according to the alarm Existing
information check antenna
Fault: the replacement of TRX Not Existing
No business warning: restart Not Existing
Cell interrupt service : Maintenance Based on
information Not Existing
Interference alarm: find the interference Not Existing
Slot allocation failure alarm: the replacement of
the TRX Not Existing
Channel congestion alarm: open half rate or
capacity expansion channel error alarm: Not Existing
Neighbor cell configuration
according to the alarm additional information Not Existing
processing
Clock alarm: change alarm hardware Not Existing
Not Existing
Not Existing
Not Existing
Not Existing
Influence Shotscree
Self-Check
Influence When Increa When Operation Required Currnent Value n/Attachm
Conclusion
Decreased ent
Suitable for smaller traffic are Suitable for traffic intensive area Satisfied
When the number of RACH confli In the case of less RACH conflict, the SLO value should be Satisfied
Specifies the time that TEO hasSpecifies the time that TEO has a role for the C2, and the Satisfied
Defined in the time of PET, the Defined in the time of PET, the temporary offset value of tSatisfied
0 0 Satisfied
0 0 Satisfied
0 0 Satisfied
IDLE state is more likely to be Reduce traffic to enter MS enter /prevent Satisfied
Under the condition of Standby The
o boundary of the location area reduced cell reselection Satisfied
0 0 Satisfied
0 0 Satisfied
Difficult to become a candidate Easy
c to become a candidate cell, but does not guarantee theSatisfied
Increase the transmission pow Reduced cell phone (900M) transmit power Satisfied
Increase the transmission pow Reduced cell phone (1800M) transmit power
Reduce coverage, improve serviIncrease coverage, reduce service quality
When the mobile phone is conneWhen the mobile phone is connected to the 900M network, the maximum transmission power is reduced, the covera
When the mobile phone is conneWhen the mobile phone is connected to the 1800M network, the maximum transmission power is reduced, the cover
Reduce the 900M area transmitIncrease the 900M cell emission power, reduce the coverage
Reduce the 1800M area transmi Increase the 1800M cell emission power, reduce the coverage
Cell can reduce the power of t Cell can be reduced power range
s, to accelerate the return of investment in GSM network, no need to replace the existing equipment or any hardware
ce in the network, and hence the mobiles experience better radio conditions.
ser. This reduces the energy consumption required per Erlang significantly.
gcapacity
constrained by the access grant channel (AGCH) capacity.
extensions.
ster.
aditional PACCH channel joint paging to avoid packet transmission in mobile phone state because the paging message cannot receive the PCH channel lead to receiving C
he need ofadditional Radio Frequency (RF) modules and also helps in network planning.
network operating costs by reducing energy consumption. In Flexi EDGE BTS, the operator saves around 40 W by powering down one dual TRX.
If SDCCH
congestion
:SDCCH
TCH issue: for
location
Refer to
>99% updating
SDCCH
document issue:
ratio<50%
Refer to
processing
>99% SDCCH
document
procedureissue:
Refer to
processing
<2% document
procedure
Weak
processing
coverage :check
procedure
cell transmit
level [-80,-47]:qual [6~7] power, adjust
Investigation
check cell of interference and hardware failure
proportion<5% the antenna,
level [-110,-90]:qual [6~7] transmit
replaced by the
proportion<5% power,
high gainadjust
1 Check
the antenna,
<3% antenna,
frequency add
replaced
the pull far by
cell
1 Check
interference
the
<3% ,add new gain
high
frequency
2, whether the
antenna,
station add
interference
cell
the with
pull far
TA>5 ratio<20% 2, whether the
repeater
cell
Adjust
cell with the antenna or reduce cell power. ZEUG:SEG=X,PMAX2=4;
3, Check
,add new
urban: 0~2 repeater
whether
station
Help to determine the cell coverage distance
surban:2~4 3, check the
external
district TA,
interference
>94% whetherby the
caused
overshooting of
investigation
>94% 4, check the trx
interference
level
sourcesquality,
1 Check
<5% determine
4, check the the
frequency
trx hardware
district TA,
interference
0 issue
whetheror
2, whether the
frequency
with issue
overshooting
cell
0 5, check the trx
repeater
level quality,
3, Check
0 determine the
whether
trx hardware
external
0 issue or
interference
frequency
caused issue
by the
0 investigation of
interference
0 sources
0
0
TCH congestion
0 The drop is higher and the poor quality can exchange frequency, locking trx, modify frequency, replace TRX
11frequency
See whether problem, change the frequency
>95% 2 the
TRXhardware
problem, change TRX
failure or TCH
1 single carrier frequency interference, frequency issue or TRX may be a hardware problem
<5% availability
2 all carrier interference may be outside interference or repeater reason
2 burst traffic
0 interference
congestion,issue or hardware issue , swap trx, lock trx, replace frequency
observation
3 opening half
rate and tuning
<2% FRL,FRU
4 Retuning
traffic balance
0 PI=Y,REO,PET
5 Reduce cell
0 coverage use
>0 parameter
RXP,PMAX1
6 expansion
SD congestion
1 view the
hardware alarm
>0.1 or SD available
2 IF cell is in
>0 border and
SDCCH for
location
updating
ratio>50% then
tuning HYS
3 the
expansion of SD
channel
6 expansion
SD congestion
1 view the
hardware alarm
or SD available
2 IF cell is in
border and
>0 SDCCH for
location
0 updating
ratio>50% then
tuning HYS
3 the
expansion
Inform the customer to check of SD
transmission MML ZYMO:ET,111;
channel
4 open
dynamic SD
5 open
BSC_RES_AVAIL enhanced
dynamic SD
=TCH CONFIGURATION CHANNEL
>99%
BSC_RES_AVAIL
=SD CONFIGURATION CHAN
>99% may be a failure to check the alarm, according to the alarm processing manual for processing.
n behalf of the hardware
<10
NOTES
NOTES
NOTES
on power is reduced, the coverage is reduced, and the network uplink bottom noise is reduced.
ion power is reduced, the coverage is reduced, and the network uplink bottom noise is reduced.
he PCH channel lead to receiving CS service
切换成功率 Handover Success Rate Description
KPI Name(English Name)
Step1: Demarcation Determine whether handover fail
切换成功率 Handover Success Rate
if local formula is not the same 切换成功率--印度 Handover Success Rate--India
Action 2.1：Alarm Checking

Alarm ID Alarm Name
7604 BTS OPERATION DEGRADED
7606 TRX FAULTY
7738 BTS WITH NO TRANSACTIONS
7767 BCCH MISSING
Mandatory checking 7744 EXCESSIVE TCH INTERFERENCE
7745 CHANNEL FAILURE RATE ABOVE DEFINED THRESHOLD
7746 CH CONGESTION IN BTS ABOVE DEFINED THRESHOLD
2725 ADJACENT CELL IDENTIFIER CONFIGURATION ERROR
7164 MASTER CLOCK UNIT HARDWARE FAULTY
8099 RECEIVED BIT ERROR RATIO (BER) > 1E-3

Except above, if
7725 TRAFFIC CHANNEL ACTIVATION FAILURE
other alarms exist,
please list them
here

参数名称
ABBREV
Paramter Name
PLMN
PLMN permitted
PI
CellReselectParamInd
REO
cellReselectOffset
EFH
enaFastAveHo
EIC
enableIntraHoInterUL
EIH
enableIntraHoInterDL
EPB
enablePwrBudgetHandover
HPP
hoPeriodPBGT
BTL
btsLoadThreshold
PRI
hoPriorityLevel
OF
hoLoadFactor
Step2:Checking
SL
rxLevMinCell
PMAX1
msTxPwrMax *GSM*dBm
PMAX2
msTxPwrMax *DCS*dBm
Step2:Checking
PMIN
PMIN
RXP
rxLevAccessMin
TXP1
TXP2
PMAX1
bsTxPwrMax *GSM*dBm
PMAX2
bsTxPwrMax *DCS*dBm
PMIN
bsTxPwrMin
SYNC
syncronised
TSC
TSC
FREQ
bcchFrequency
LAC
adjacentCellIdLac
NCC
adjCellBsicNcc
BCC
adjCellBsicBcc
Perform Neighbor Cell CheckinPerform Neighbor Cell Checking by OMStar Neighbor Cell Checking and A
Feature Name Feature's Meaning

Energy Saving mode for BCCH In the "Energy saving mode for BCCH TRX" feature, the
Double Power TRX for 2G BTS (BSS20870), is a licence based application software. W
Double Power TRX for 2G BTS
Flexible MCPA TX Power Pooli The Flexi Multiradio BTS RF Module (FXxx) has three b
STIRC STIRC is designed to cancel uplink interference and als
2G TRX Automatic Power Dow 2G automatic power down" feature introduces an energy
in poor wireless environment to improve the anti interference of the signal, improve
AMR HO Signalling Optimizati
Action 3.1: Identify Handover Fail Causes

切换原因占比 Handover Cause reason ratio
切换成功率(切入） Handover success rate（in）

Intra-PLMN& 切换成功率(切出） Handover success rate（out）
Inter-PLMN
切出成功率(小区对小区） Handover success rate（out cell to cell ）
切入成功率(小区对小区） Handover success rate（in cell to cell ）

Identify poor
下行电平质量分布 DL LEV & QUAL Distribute KPI
coverage or
Interference 上行电平质量分布 UL LEV & QUAL Distribute KPI
Analysis
上行弱覆盖比例 UL Weak coverage rate
下行弱覆盖比例 DL Weak coverage rate

TA分布 TA Distribution
平均TA值 Ave TA distance
下行0~4级质量占比 DL HQI KPI
(Cell Level) Interference Analysis

上行0~4级质量占比 UL HQI KPI
4~5级干扰比例 Interferences KPIs
载频级掉话 Drop call number in TRX
载频级0~5级质量占比 TRX Quality

(TRX Level) Coverage and Interference Analysis
Step3: Anylysis 载频级4~5级干扰占比 TRX interference
载频级分配失败次数 CALL FAIL NUMBER IN TRX

TCH拥塞率 TCH Congestion ratio
TCH拥塞次数（不含切） TCH Congestion num (not include handover)
TCH拥塞次数（含切） TCH Congestion num (include handover)
TCH话务量 Average TCH traffic
TCH全速率话务 Average FTCH traffic

Intra-PLMN
TCH半速率话务 Average HTCH traffic
每线话务量 AVE ERL PER CHANNEL
数据业务等效话务量 AVE PS traffic
切入时缺少资源数 Number of lack of radio resources during incoming han
切出时缺少资源数 Number of lack of radio resources during outgoing han
Inter-PLMN MSC 控制的的切出时，因为对方小区没有资源而导致的失败次数

The number of unsuccessful handovers due to no availab

不可用时长 Not available time
一般误码秒 Error second
严重误码秒 Serious error second

Step4: Escalate TicketAction 4.1:TT by Local Flow
Description Manual Writ
Counter/Formula Tables Name
Reference Value Instructions Operation Required

a = p_nbsc_traffic >99%
Sum(MSC_I_SUCC_HO+ MSC_O_SUCC_HO+ BSC_I_SUCC_HO+ Judge Handover failure reason: TOPN cell or Whole network
b = p_nbsc_service if TOPN cell , then perform action2
c = p_nbsc_ho
0.50%
Influence(Major,Medium,Minor) Meaning Instructions

Medium 0 Antenna alarm: according to the alarm information check antenna
Medium 0 Fault: the replacement of TRX
Major 0 No business warning: restart
Major 0 Cell interrupt service : Maintenance Based on information
Major 0 Interference alarm: find the interference
Major 0 Slot allocation failure alarm: the replacement of the TRX
Major 0 Channel congestion alarm: open half rate or capacity expansion channel
Major 0 Neighbor cell configuration error alarm: according to the alarm additional information proce
Major 0 Clock alarm: change alarm hardware
Major 0 Notification transfer view fault
Major 0 GENA or PCU to solve the switching
Influence When
Value Range Reference ValInfluence Operation Required
Decreased
(0…7) 0 0 0
(Y/N) Y 0 0
(0…126 step 2)dB 0 IDLE state is m Reduce traffic to enter MS enter /prevent
(Y/N) Y 0 0
(Y/N) Y for non-hopping, N0 0
(Y/N) Y for non-hopping, N0 0
(Y/N) Y 0 0
(0…63)SACCH 6 Slow PBGT hanFast PBGT handover speed
(0…100)% 80 Allow more trafReduce traffic (by switching) into the cell
(0…7) 3 The adjacent are

Adjacent area list in the list of the more after
(0…7) 1 Priority downgrPriority to downgrade the step size, the smaller the more slow down
(-110…-47) dbm -98 Cut into the moThe cut is easier, but can not guarantee the quality of the cut
(5…43 step 2) *GSM*dBm 33 Increase the t Reduced cell phone (900M) transmit power
(0…36 step 2) *DCS*dBm 30 Increase the t Reduced cell phone (1800M) transmit power
(5…43 step 2) *GSM*dBm 5 Increase the t Reduced cell phone (900M) transmit power
(0…36 step 2) *DCS*dBm 0 Increase the t Reduced cell phone (1800M) transmit power
(-110…-47)dBm -102~-98 Reduce coveragIncrease coverage, reduce service quality
(5…43 step 2) *GSM*dBm 33 When the mobil

When the mobile phone is connected to the 900M network, the maximum tra
(0…30 step 2) *DCS*dBm 30 When the mobil

When the mobile phone is connected to the 1800M network, the maximum tr
(0…30 step 2)DB 0 Reduce the 900Increase the 900M cell emission power, reduce the coverage
(0…30 step 2)DB 0 Reduce the 180Increase the 1800M cell emission power, reduce the coverage
(0…30 step 2)DB 20 Cell can reduc Cell can be reduced power range
(Y/N) Same BCF set Y Setting the erro0
(0…7) Must equal BCC OF TSet the error c 0
0 Must equal with BTSSetting the erro0
1...65533 Must equal with BTSSetting the erro0
(0…7) Must equal with BTSSetting the erro0
(0…7) Must equal with BTSSetting the erro0
y OMStar Neighbor Cell Checking and Analysis functions
Adapted Scenario and Gain

The reduced electricity consumption due to the "Energy saving mode for BCCH TRX" helps operators to reduce network operating costs.
When
CAUSE this feature is activated in the network, most of the energy savings are provided by the dummy burst power reduction during periods of low traffic, e.g. at n
The reduced transmit power of dummy bursts, and the limited dynamic power control allowed for active CS channels, result in a reduction in downlink interferenc
REASON/SUM(CAUSE_UP_QUAL+CAUSE_UP_LEVEL+CAUSE
_DOWN_QUAL+CAUSE_DOWN_LEV+CAUSE_DISTANCE+CA
Increase cover distance
The Flexible MCPA TX Power Pooling feature provides the following benefits to operators:
USE_MSC_INVOC+CAUSE_INTFER_UP+CAUSE_INTFER_DW
•It allows the operators to utilize the output power of the MCPAs optimally.
N+CAUSE_UMBR+CAUSE_PBDGT+CAUSE_OMC+CAUSE_CH
•It increases the capacity of the BTS for a given coverage area without the need ofadditional Radio Frequency (RF) modules and also helps in network planning.
_ADM+CAUSE_DIR_RETRY)
•It reduces
CAUSE the call drop rate in coverage limited networks.
REASON:
•It enables the user to enhance coverage and capacity at the same time. It also enhances the coverage or capacity individually which results in flexibility.
因为上行质量发起的切换尝试次数：
to enhance the MOS value, reduce the words
CAUSE_UP_QUAL
因为上行电平发起的切换尝试次数：
When this feature is activated in the network, the operator can lower the network operating costs by reducing energy consumption. In Flexi EDGE BTS, the oper
CAUSE_UP_LEVEL Check which cell have low
success rate.
因为下行质量发起的切换尝试次数：
improve customer perception 1 interference issue
CAUSE_DOWN_LEVEL 2 hardware issue
因为下行电平发起的切换尝试次数： 3 frequency issue
CAUSE_DOWN_LEVEL 4 missing Neighbor
5 Wrong define adj
因为距离发起的切换尝试次数： parameter
CAUSE_DISTANCE p_nbsc_ho PBGT handover U nder normal circumstances, a good wireless environment PB
6 overshooting
因为MSC发起的切换尝试次数： 7 Check Parameter
sum(MSC_I_TCH_TCH+MSC_I_SDCCH_TCH+MSC_I_SDCCH+BS p_nbsc_ho >80% Check the hardware ,clock issue,Interference problem, Action 2,3,4
SL,AUCL,EPB,BLT,PRI,OF,SYN
CAUSE_MSC_INVOC C,PMRG,LMRG,QMRG
因为上行干扰发起的切换尝试次数：
Sum(MSC_O_SUCC_HO+BSC_O_SUCC_HO+CELL_SUCC_HO)/p_nbsc_ho >95% 8 for Inter-plmn,To check if
CAUSE_INTFER_UP 3 days sum
the neighbour LAC has been
因为下行干扰发起的切换尝试次数：
100*sum(ho_att_to_adj - ho_succ_to_adj)/Sum(ho_att_to_ap _nbsc_ho_adj ho att>100
defined in the MSC( Telnet
CAUSE_INTFER_DWN >95% MSC ,ZEIO:LACID;) To check
3 days sum inter-plmn handover
因为伞切换发起的切换尝试次数：
100*sum(ho_att_from_adj - ho_succ_from_adj)/Sum(ho_attp _nbsc_ho_adj ho att>100 agreements use command
CAUSE_UMBR >80% ZMXP:NAME=*;
因为PBGT发起的切换尝试次数：
sum over a range (class_upper_range) 9 for Inter-plmn, check
(freq_dl_qual0+freq_dl_qual1+freq_dl_qual2+freq_dl_qual3+freq_dl_qual4 whether any issue in the first
CAUSE_PBDGT
+freq_dl_qual5+freq_dl_qual6+freq_dl_qual7)/ Counters from table(s): 1~7 points in Target cell.
sum over a range (class_upper_range) level [-80,-47] Investigation
因为信道操作发起的切换尝试次数：
sum over all ranges p_nbsc_rx_statistics
(freq_ul_qual0+freq_ul_qual1+freq_ul_qual2+freq_ul_qual3+freq_ul_qual4 10 If uper steps allofnointerference
used and hardware failure
CAUSE_CH_ADM
(freq_dl_qual0+freq_dl_qual1+freq_dl_qual2+freq_dl_qual3+freq_dl_qual4
Counters from table(s): Weak
,you cancoverage :check celland
delete neighbor transmit power, adjust the antenna, replaced by th
因为直接重试发起的切换尝试次数：
sum over all ranges p_nbsc_rx_statistics level [-110,-9 ,add
then new station
recreate relation
(freq_ul_qual0+freq_ul_qual1+freq_ul_qual2+freq_ul_qual3+freq_ul_qual4 11 Step 1 to 10 are all
CAUSE_DIR_RETRY checked, there is no use,
100*(SUM(freq_ul_qual0+freq_ul_qual1+freq_ul_qual2+fre P_NBSC_RX_STATIST<3%
+freq_ul_qual5+freq_ul_qual6+freq_ul_qual7)
please
check carry
cell out the DT test,
transmit powe
and in the background
100*(SUM(freq_dl_qual0+freq_dl_qual1+freq_dl_qual2+fre P_NBSC_RX_STATIST<3% tracking signaling
TA=0
TA=1
…….
TA=63 TA>5 ratio<20 Adjust the antenna or reduce cell power. ZEUG:SEG=X,PMAX2=4;
p_nbsc_timing_advance
(freq_reports)/ urban: 0~2
ave_ms_bs_dist p_nbsc_timing_advasurban:2~4 Help to determine the cell coverage distance
sum over all ranges 1 Check frequency interference
(freq_reports) Counters from table(s): 2 whether the cell with repeater
100*sum(freq_dl_qual0+freq_dl_qual1+freq_dl_qual2+freq_p_nbsc_rx_qual >94% 1
3 Check
check thefrequency
district interference
TA, whether overshooting
Counters from table(s): 2
4 whether
check thethe trxcell with
level repeater
quality, determine the trx hardware issue or frequency is
100*sum(freq_ul_qual0+freq_ul_qual1+freq_ul_qual2+freq_ >94% 3 Check whether external interference caused by the investigation of interfer
p_nbsc_rx_qual 4 check the district TA, whether overshooting
1
5 Check frequency
trx levelinterference
100*Sum(Ave_Idle_f_Tch_4/Res_Av_Denom7+Ave_Idle_h_ Counters from table(s): <5% check the quality, determine the trx hardware issue or frequency is
2 whether the cell with repeater
p_nbsc_res_avail
TCH_fail_call_ho 3 Check whether external interference caused by the investigation of interfer
tch_radio_fail p_nbsc_underlay 0 The drop is higher and the poor quality can exchange frequency, locking trx, m
+freq_ul_qual3+freq_ul_qual4+freq_ul_qual5)/sum(freq_ul
_qual0+freq_ul_qual1+freq_ul_qual2+freq_ul_qual3+freq_ p_nbsc_rx_qual >95% 1 frequency problem, change the frequency
ul_qual4+freq_ul_qual5+ 2 TRX problem, change TRX
freq_ul_qual6+freq_ul_qual7) 1 single carrier frequency interference, frequency issue or TRX
(AVE_FULL_TCH_IF4+AVE_HALF_TCH_IF4+AVE_FULL_TCH_IF5+AVE_HALF_TCH_IF5)/(AVE_FULL_TCH_IF1+AVE_HALF_TCH_IF1+AVE_FULL_TCH_I
p_nbsc_underlay <5% 2 all carrier interference may be outside interference or repeater reason
TCH_REQUEST-TCH_SUCC_SEIZ P_NBSC_UNDERLAY 0 interference issue or hardware issue , swap trx, lock trx, repl

100*[sum(a.tch_call_req-a.tch_norm_seiz)-sum(b.msc_o_sdcch_tch+ .bsc_o_sdcch_tch+b.cell_sdcch_tch)+sum(a.tch_succ_seiz_for_dir_acc)- sum(a.tch_rej_due_req_ch_a_
a = p_nbsc_traffic <2% TCH congestion
- sum(a.tch_rej_due_req_ch_a_if_crc-(b.bsc_i_unsucc_a_int_circ_type+b.msc_controlled_in_ho+b.ho_unsucc_a_int_circ_type))]
b = p_nbsc_ho
Counters from table(s): 1 See whether the
(a.QUE_ALL_ASS_REQ_FAIL+a.QUE_NALL_ASS_REQ_FAIL- a = p_nbsc_traffic 0 hardware failure or TCH
b = p_nbsc_ho availability
sum(TCH_REQ_REJ_LACK-TCH_REJ_DUE_REQ_CH_A_IF_CRCp_nbsc_traffic 0 2 burst traffic congestion,
observation
3 opening half rate and
sum(ave_busy_tch / res_av_denom14) p_nbsc_res_avail >0 tuning FRL,FRU
4 Retuning traffic balance
AVE_TCH_BUSY_FULL p_nbsc_res_avail PI=Y,REO,PET
5 Reduce cell coverage use
parameter RXP,PMAX1
AVE_TCH_BUSY_HALF p_nbsc_res_avail 6 expansion
SD congestion
SUM(AVE_BUSY_TCH/RES_AV_DENOM14)/(SUM(AVE_AVAI p_nbsc_res_avail >0.1 1 view the hardware alarm
or SD available
AVE_BUSY_GPRS_CH_DL/AVE_BUSY_GPRS_CH_DEN p_nbsc_packet_contr>0 2 IF cell is in border and
SDCCH for location updating
ratio>50% then tuning HYS
HO_FAIL_RES_TO_ADJ P_NBSC_HO_ADJ 0
3 the expansion of SD
channel
HO_FAIL_RES_FROM_ADJ P_NBSC_HO_ADJ 0 3 open dynamic SD
4 open enhanced dynamic
MSC_O_FAIL_LACK P_NBSC_HO 0 SD
NOT_AVAIL_TIME
ERR_SEC Inform the customer to check transmission
P_NBSC_ET_BSC
ERR_SEC_SEVER
Currnent Value Self-Check NOTES
r Whole network
TOPN Cell
2.10%
Self-Check(Existing
NOTES
or not?)
Existing
Not Existing
Not Existing
Not Existing
Not Existing
Not Existing
Not Existing
larm additional information processing Not Existing
Not Existing
Not Existing
Not Existing
Not Existing
Not Existing
Currnent Value Self-Check NOTES
aller the more slow down
quality of the cut

e 900M network, the maximum transmission power is reduced, the coverage is reduced, and the network uplink bottom noise is reduced.
e 1800M network, the maximum transmission power is reduced, the coverage is reduced, and the network uplink bottom noise is reduced.
uce the coverage
duce the coverage
ng costs.
g periods of low traffic, e.g. at night time. With dynamic power control of active dedicated channels, the feature reduces electricity consumption throughout the day.
reduction in downlink interference caused by the BCCH frequency.
also helps in network planning.
hich results in flexibility.
n. In Flexi EDGE BTS, the operator saves around 40 W by powering down one dual TRX.
od wireless environment PBGT handover accounted for more than 50%, to view the reasons for the proportion of the handover, you can quickly locate t
e problem, Action 2,3,4
ardware failure
adjust the antenna, replaced by the high gain antenna, add the pull far cell
ower. ZEUG:SEG=X,PMAX2=4;
ng
trx hardware issue or frequency issue
sed by the investigation of interference sources
ng
trx hardware issue or frequency issue
sed by the investigation of interference sources
exchange frequency, locking trx, modify frequency, replace TRX
ence, frequency issue or TRX may be a hardware problem

erference or repeater reason
e , swap trx, lock trx, replace frequency
ption throughout the day.
andover, you can quickly locate the cell wireless environment.

掉话分析Drop Call Analysis Descriptio
Required Steps Required Actions KPI 名称(Chinese
KPIName)
Name(English N
Determine whether call drop
occurs on some top cells or 掉话率 Drop call rate
Step1: Demarcation the entire network.
if local formula is not the same
with the one in D4, please
write donw in D5 like the 掉话率--印度 Drop call rate--India
demo
Alarm ID Alarm Name
7604 BTS OPERATION DEGRAD
7606 TRX FAULTY
7738 BTS WITH NO TRANSACT
7767 BCCH MISSING
Mandatory checking 7744 EXCESSIVE TCH INTERF
7745 CHANNEL FAILURE RATE
7746 CH CONGESTION IN BTS
2725 ADJACENT CELL IDENTIF
7164 MASTER CLOCK UNIT HA
8099 RECEIVED BIT ERROR RATI
Except above, if other alarms 7725 TRAFFIC CHANNEL ACTIV

exist, please list them here

参数名称
Paramter ABBREV
Name
radioLinkTimeout RLT
PI
cellReselectParamInd
cellReselectOffsetREO
powerCtrlEnabled PENA
EPB
enablePwrBudgetHandover
PMAX1
msTxPwrMax *GSM*dBm
PMAX2
msTxPwrMax *DCS*dBm
PMIN
PMIN
rxLevAccessMin RXP
TXP1
TXP2
PMAX1
bsTxPwrMax *GSM*dBm
Step2:Checking
PMAX2
bsTxPwrMax *DCS*dBm
bsTxPwrMin PMIN
callReestablishmentA RE
optimumRxLevUL LEV
msMaxDistanceInCallSetup
UL dtxMode DTX

AMR Capacity The “Wideband AMR” (BSS20960
(E)GPRS DL Power The (E)GPRS Downlink (DL) Pow

Wideband AMR Wideband AMR is adopted by bo
Separate UL&DL AMRindependent UL/DL AMR link thr

in poor wireless environment to improve the anti interference of the signal, improve
AMR HO Signalling
Optimization
AMR Progressive AMR Progressive Power Control
Power Control
AMR Unpacking This feature provides new AMR
Optimization
Adjustable UL RLT This feature allows the operato
Increase Step
FACCH and SACCH r
FACCH repetition f
y speech quality in radio channels whose carrier-to-interference ratio (C/I) is up to 4 dB worse than that needed to give reliable operation of the FACCH and SACCH control channels. T
The effective C/I for downlink FACCH and uplink/downlinkFACCHSACCHrepetition f
can be improved by increasing the base station (BTS) Tx power for FACCH, or by repeating the
FACCH Power Incre
AMR Signalling Mea
Double Power TRX for 2G BTS (BSS20870), is a licence based application software. W
Double Power TRX f
Flexible MCPA TX PThe Flexi Multiradio BTS RF M
STIRC STIRC is designed to cancel up
2G TRX Automatic 2G automatic power down" feat

Action 3.1: Identify call drop causes
Radio Link Faults Number of TCH transaction
因为无线环境掉话
failures due to radio failure
Number of TCH transaction
Handover Faults 因为切换导致的掉 failures due to a radio
话 failure of the old channel
during a of
Number TCHTCHhandover
transaction
因为Abis接口原因 failures due to Abis
导致的掉话 interface failure during a
call
failures due to Abis
因为Abis接口切换
interface failure on the old
原因导致的掉话
channel during a TCH
handover
因为A接口掉话 failures due to A-interface
failure during a call
因为A接口掉话（切 failures due to A-interface
换中） failure on the old channel
during a handover attempt
因为TR掉话 failures due to transcoder
failure of TCH
Number
transactions ended due to
因为TR掉话（切换
transcoderfailure of an old
中）
Equipment and Link Faults channel during a handover
on a TCH.
因为LAPD导致的掉 Number of TCH transaction
话 failures due to LAPD failure
因为BTS原因掉话 Number of TCH transaction fa

The number of TCH
因为激活失败导致 transaction failures due to
的掉话 activation
failure
因为用户行为导致 Number of TCH transaction
的掉话 failures due to user actions
因为BCSU重置导致
Number of TCH transaction f
掉话
The number of TCH
transaction failures due to
因为网络重配导致 radio
掉话
network reconfiguration
actions
下行电平质量分布 DL LEV & QUAL Distribute
Identify poor coverage or
Interference Analysis
上行电平质量分布 UL LEV & QUAL Distribute

(Cell Level) Interference Analysis上行0~4级质量占比 UL HQI KPI
载频级掉话 Drop call number in TRX
载频级0~5级质量占
(TRX Level) Coverage and Interference Analysis TRX Quality
比
载频级4~5级干扰占
TRX interference
比
Step3: Anylysis
TCH Congestion num (not incl

TCH拥塞次数（不含切）
TCH Congestion num (include

TCH拥塞次数（含切）
数据业务等效话务量AVE PS traffic
SDCCH话务量 Average SDCCH traffic
SDCCH拥塞次数 SD CONGESTION NUM

Action 3.5: Handover Analysis

Handover success
切换成功率(切入）
rate（in）
Handover success
切换成功率(切出）
rate（out）
Handover success
切出成功率(小区对小区）
rate（out cell to cell ）
Handover success rate（in
切入成功率(小区对小区）
cell to cell）
切入时缺少资源数 Number of lack of radio res
Number of lack of radio resources during outgoing handovers
切出时缺少资源数
handovers.
TCH配置信道数 TCH CONFIGURATION CH
TCH可用信道数 TCH AVALIBLE CHANNEL
TCH可用率 TCH Availability KPIs
SDCCH配置信道数 SD CONFIGURATION CHA
SDCCH可用信道数 SD AVALIBLE CHANNEL
SDCCH可用率 SDCCH Availability KPIs
全速率可用信道数 Full rate available channel
半速率可用信道数 Half rate available channel
链路平衡 LINK BALANCE
Step4: Escalate Ticket Action 4.1:TT by Local Flow

Description
Counter/Formula Tables Name Reference Value
100*[sum(a.tch_radio_fail+a.tch_rf_old_ho+a.tch_abis_fail_cal
l+a.tch_abis_fail_old+a.tch_a_if_fail_call+a.tch_a_if_fail_old+a
.tch_tr_fail+a.tch_tr_fail_old+a.tch_lapd_fail+a.tch_bts_fail+a.t Counters from table(s):
ch_user_act+a.tch_bcsu_reset+a.tch_netw_act+a.tch_act_fail a = p_nbsc_traffic
100*sum(a.TCH_RADIO_FAIL+a.TCH_RF_OLD_HO+a.TCH_ <1%
_call)- sum(b.tch_re_est_assign)]/[sum(a.tch_norm_seiz) b = p_nbsc_service
TR_FAIL_OLD+a.TCH_ABIS_FAIL_OLD+a.TCH_A_IF_FAIL_
+sum(c.msc_i_sdcch_tch+c.bsc_i_sdcch_tch+c.cell_sdcch_tc c = p_nbsc_ho
OLD+a.TCH_TR_FAIL+a.TCH_LAPD_FAIL+a.TCH_BTS_FAI
h)-sum(a.tch_succ_seiz_for_dir_acc)+ Counters from table(s):
L+a.TCH_USER_ACT+a.TCH_BCSU_RESET+a.TCH_NETW
sum(a.tch_seiz_due_sdcch_con)- sum(b.tch_re_est_assign)] a = p_nbsc_traffic
_ACT+a.TCH_ABIS_FAIL_CALL+a.TCH_A_IF_FAIL_CALL)/s
c = p_nbsc_ho
um(a.MS_TCH_SUCC_SEIZ_ASSIGN_CMPLT+c.MSC_I_SD
CCH_TCH+c.BSC_I_SDCCH_TCH+c.MSC_HO_WCDMA_R
AN_SUCC)
Antenna alarm: according to the alarm information
Medium 0 check antenna

Major 0 information
Slot allocation failure alarm: the replacement of the
Major 0 TRX
Channel congestion alarm: open half rate or capacity
Major 0 expansion channel
Neighbor cell configuration error alarm: according to
Major 0 the alarm additional information processing
Major 0 Clock alarm: change alarm hardware
Value Range Reference Value Influence When

(4…64,step 4)SACCH 32 reduce drop call
(Y/N) Y 0
(0…126 step 2)dB 0 IDLE state is more like
(Y/N) Y Open to reduce networ
(Y/N) Y 0
(5…43 step 2) *GSM*dBm 33 Increase the transmis
(0…36 step 2) *DCS*dBm 30 Increase the transmis
(-110…-47)dBm -102~-98 Reduce coverage, impr
(5…43 step 2) *GSM*dBm 33 When the mobile phone
(0…30 step 2) *DCS*dBm 30 When the mobile phone
(0…30 step 2)DB 0 Reduce the 900M area
(0…30 step 2)DB 0 Reduce the 1800M are
(0…30 step 2)DB 20 Cell can reduce the p
(Y/N) Y Open can reduce the
(-109…-47)(dbm) -80 Uplink optimization lev
(0,,,255)TA 255 Setting errors can cause the network to be unable to access
(0(MS may use DTX)/1(MS shall use DTX)/2(MS shall not use 1 Open can reduce uplin
g by OMStar Neighbor Cell Checking and Analysis functions

Adapted Scenario and Gain
By providing good voice quality and increased communication capabilities, to accelerate the return of investment in GSM network, no need to re
The (E)GPRS DL Power Control feature provides the following benefits to the operator:
•It reduces transmit power, which in turn helps in reducing the interference in the network, and hence the mobiles experience better radio condit
•It maintains
to improve voice
the quality
quality whencalls
of voice the data usage
and MOS increases.
value of mobile users
independent UL/DL AMR link threshold can make a certain wireless condition to obtain more effective optimization effect
improve customer perception
drop rate by half or the same rate of drop out rate of 15% of the traffic gain, which is equivalent to the same traffic energy savings of 15%
CAPEX savings & improved network quality by reducing drop call rate
Reduction in CS Dropped Call Ratio
•reduced dropped call rate in heavily loaded networks

•increased coverage, including in-building coverage, in lightly loaded networks
•FACCH and SACCH repetition improve the C/I by up to 4 dB
The Flexible MCPA TX Power Pooling feature provides the following benefits to operators:
Increase
•It allowscover distanceto utilize the output power of the MCPAs optimally.
the operators
•It increases the capacity of the BTS for a given coverage area without the need ofadditional Radio Frequency (RF) modules and also helps in ne
•It enables the
to enhance theuser
MOStovalue,
enhance coverage
reduce and capacity at the same time. It also enhances the coverage or capacity individually which results in fl
the words
When this feature is activated in the network, the operator can lower the network operating costs by reducing energy consumption. In Flexi EDG
tch_radio_fail a = p_nbsc_traffic 0
tch_rf_old_ho a = p_nbsc_traffic 0
tch_abis_fail_call a = p_nbsc_traffic 0
tch_abis_fail_old a = p_nbsc_traffic 0
tch_a_if_fail_call a = p_nbsc_traffic 0
tch_a_if_fail_old a = p_nbsc_traffic 0
a = p_nbsc_traffic 0
tch_tr_fail
tch_tr_fail_old
tch_lapd_fail
tch_bts_fail
TCH_ACT_FAIL
tch_user_act a = p_nbsc_traffic 0
tch_bcsu_reset a = p_nbsc_traffic 0
tch_netw_act a = p_nbsc_traffic 0
sum over a range (class_upper_range) Counters from table(s): level [-80,-47]:qual

(freq_dl_qual0+freq_dl_qual1+freq_dl_qual2+freq_dl_qual3+fr p_nbsc_rx_statistics [6~7] proportion<5%
eq_dl_qual4
+freq_dl_qual5+freq_dl_qual6+freq_dl_qual7)/
sum over all ranges
(freq_dl_qual0+freq_dl_qual1+freq_dl_qual2+freq_dl_qual3+fr
eq_dl_qual4
(freq_ul_qual0+freq_ul_qual1+freq_ul_qual2+freq_ul_qual3+fr p_nbsc_rx_statistics [6~7] proportion<5%
eq_ul_qual4
TA:class_upper_range Counters from table(s): <3%
TA=0 p_nbsc_timing_advance
sum
TA=1 over all ranges
ave_ms_bs_dist
(freq_ul_qual0+freq_ul_qual1+freq_ul_qual2+freq_ul_qual3+fr <3%
……. p_nbsc_timing_advance
eq_ul_qual4
TA=63
100*(SUM(freq_ul_qual0+freq_ul_qual1+freq_ul_qual2+freq_u
sum over a range (class_upper_range) P_NBSC_RX_STATISTIC
l_qual3+freq_ul_qual4+freq_ul_qual5+freq_ul_qual6+freq_ul_ S TA>5 ratio<20%
(freq_reports)/
qual7) Where
sum over all ranges
100*(SUM(freq_dl_qual0+freq_dl_qual1+freq_dl_qual2+freq_d P_NBSC_RX_STATISTIC urban: 0~2
CLASS_UPPER_RANGE<=15)/SUM(freq_ul_qual0+freq_ul_q
(freq_reports)
l_qual3+freq_dl_qual4+freq_dl_qual5+freq_dl_qual6+freq_dl_ S surban:2~4
100*sum(freq_dl_qual0+freq_dl_qual1+freq_dl_qual2+freq_dl
ual1+freq_ul_qual2+freq_ul_qual3+freq_ul_qual4+freq_ul_qua
qual7) WHERE
_qual3+freq_dl_qual4)/sum(freq_dl_qual0+freq_dl_qual1+freq Counters from table(s):
l5+freq_ul_qual6+freq_ul_qual7)
CLASS_UPPER_RANGE<=20)/SUM(freq_dl_qual0+freq_dl_q >94%
_dl_qual2+freq_dl_qual3+freq_dl_qual4+freq_dl_qual5+freq_d
100*sum(freq_ul_qual0+freq_ul_qual1+freq_ul_qual2+freq_ul p_nbsc_rx_qual
ual1+freq_dl_qual2+freq_dl_qual3+freq_dl_qual4+freq_dl_qua
l_qual6+freq_dl_qual7)
_qual3+freq_ul_qual4)/sum(freq_ul_qual0+freq_ul_qual1+freq
l5+freq_dl_qual6+freq_dl_qual7) Counters from table(s):
>94%
_ul_qual2+freq_ul_qual3+freq_ul_qual4+freq_ul_qual5+freq_u p_nbsc_rx_qual
l_qual6+freq_ul_qual7)
100*Sum(Ave_Idle_f_Tch_4/Res_Av_Denom7+Ave_Idle_h_Tc Counters from table(s):
<5%
p_nbsc_res_avail
TCH_fail_call_ho
sum(freq_ul_qual0+freq_ul_qual1+freq_ul_qual2 p_nbsc_underlay 0
tch_radio_fail
+freq_ul_qual3+freq_ul_qual4+freq_ul_qual5)/sum(freq_ul_qu
（AVE_FULL_TCH_IF4+AVE_HALF_TCH_IF4+AVE_FULL_T
al0+freq_ul_qual1+freq_ul_qual2+freq_ul_qual3+freq_ul_qual p_nbsc_rx_qual >95%
CH_IF5+AVE_HALF_TCH_IF5）/
4+freq_ul_qual5+
freq_ul_qual6+freq_ul_qual7) p_nbsc_underlay <5%
CH_IF2+AVE_HALF_TCH_IF2+AVE_FULL_TCH_IF3+AVE_
100*[sum(a.tch_call_req-a.tch_norm_seiz)-
HALF_TCH_IF3+AVE_FULL_TCH_IF4+AVE_HALF_TCH_IF
sum(b.msc_o_sdcch_tch+ .bsc_o_sdcch_tch+b.cell_sdcch_tch)
4+AVE_FULL_TCH_IF5+AVE_HALF_TCH_IF5）
+sum(a.tch_succ_seiz_for_dir_acc)-
sum(a.tch_rej_due_req_ch_a_if_crc - Counters from table(s):
(b.bsc_i_unsucc_a_int_circ_type))]/[sum(a.tch_call_req)
a = p_nbsc_traffic <2%
b = p_nbsc_ho
(a.QUE_ALL_ASS_REQ_FAIL+a.QUE_NALL_ASS_REQ_FAIL-
(b.bsc_i_unsucc_a_int_circ_type+b.msc_controlled_in_ho+b.ho_un
a.A_IF_CRC_MISMATCH_CALL_SETUP+a.REMOVAL_FROM_QUE_D Counters from table(s):
succ_a_int_circ_type))]
UE_TO_DR)- a = p_nbsc_traffic 0
(b.MSC_O_SDCCH_TCH+b.BSC_O_SDCCH_TCH+b.CELL_SDCCH_TCH b = p_nbsc_ho
)
sum(TCH_REQ_REJ_LACK-TCH_REJ_DUE_REQ_CH_A_IF_CRC) p_nbsc_traffic 0
sum(ave_busy_tch / res_av_denom14) p_nbsc_res_avail >0
AVE_TCH_BUSY_FULL p_nbsc_res_avail
SUM(AVE_BUSY_TCH/RES_AV_DENOM14)/
+SUM(AVE_GPRS_CHANNELS_SUM/AVE_GPRS_CHANNELS_DEN)- p_nbsc_res_avail >0.1
SUM(AVE_PERMANENT_GPRS_CH_SUM/AVE_PERMANENT_GPRS_
CH_DEN))
AVE_BUSY_GPRS_CH_DL/AVE_BUSY_GPRS_CH_DEN p_nbsc_packet_control_unit >0
(AVE_BUSY_SDCCH/RES_AV_DENOM15) P_NBSC_RES_AVAIL >0
SDCCH_BUSY_ATT P_NBSC_TRAFFIC 0
NOT_AVAIL_TIME
ERR_SEC
P_NBSC_ET_BSC
ERR_SEC_SEVER
sum(MSC_I_TCH_TCH+MSC_I_SDCCH_TCH+MSC_I_SDC
CH+BSC_I_TCH_TCH+BSC_I_SDCCH_TCH+BSC_I_SDCC
H +CELL_TCH_TCH+CELL_SDCCH_TCH+ CELL_SDCCH)/
Sum(MSC_O_SUCC_HO+BSC_O_SUCC_HO+CELL_SUCC
sum(MSC_I_TCH_TCH_AT+MSC_I_SDCCH_TCH_AT+MSC p_nbsc_ho >80%
_HO)/Sum((MSC_O_TCH_TCH_AT+MSC_O_SDCCH_TCH_
_I_SDCCH_AT+BSC_I_TCH_TCH_AT+BSC_I_SDCCH_TCH
AT+MSC_O_SDCCH_AT+BSC_O_TCH_TCH_AT+BSC_O_S
_AT+BSC_I_SDCCH_AT+CELL_TCH_TCH_AT+CELL_SDC p_nbsc_ho >95%
DCCH_TCH_AT+BSC_O_SDCCH_AT+CELL_TCH_TCH_AT
CH_TCH_AT+CELL_SDCCH_AT) 3 days sum
100*sum(ho_att_to_adj - ho_succ_to_adj)/Sum(ho_att_to_adj) p _nbsc_ho_adj
+CELL_SDCCH_TCH_AT+CELL_SDCCH_AT) ho att>100
3 days sum
>95%
100*sum(ho_att_from_adj -
p _nbsc_ho_adj ho att>100
ho_succ_from_adj)/sum(ho_att_from_adj)
>80%
HO_FAIL_RES_TO_ADJ P_NBSC_HO_ADJ 0
HO_FAIL_RES_FROM_ADJ P_NBSC_HO_ADJ 0
(AVE_GPRS_CHANNELS_SUM/AVE_GPRS_CHANNELS_D
EN)- P_NBSC_RES_AVAIL
((AVE_AVAIL_TCH_SUM/AVE_AVAIL_TCH_DEN)+
(AVE_PERMANENT_GPRS_CH_SUM/AVE_PERMANENT_
GPRS_CH_DEN)
EN)- P_NBSC_RES_AVAIL =TCH CONFIGURATION CHANNEL
100*[sum(ave_avail_TCH_sum/ave_avail_TCH_den+ave_GP
RS_channels_sum/ave_GPRS_channels_den)]/
GPRS_CH_DEN)+AVE_NON_AVAIL_TCH_TIMESLOT)
[sum(ave_avail_TCH_sum/ave_avail_TCH_den+ave_GPRS_
>99%
p_nbsc_res_avail
channels_sum/ave_GPRS_channels_den+ave_non_avail_TC
(AVE_SDCCH_SUB/RES_AV_DENOM3+AVE_NON_AVAIL_
H)] P_NBSC_RES_AVAIL
SDCCH)
(AVE_SDCCH_SUB/RES_AV_DENOM3) P_NBSC_RES_AVAIL =SD CONFIGURATI
100*(AVE_SDCCH_SUB/RES_AV_DENOM3)/ P_NBSC_RES_AVAIL >99%

(AVE_SDCCH_SUB/RES_AV_DENOM3+AVE_NON_AVAIL_SDCCH)
(AVE_GPRS_CHANNELS_SUM/
(ave_bs_power - ave_dl_sig_str) - (ave_ms_power -
AVE_GPRS_CHANNELS_DEN)- p_nbsc_res_avail
ave_ul_sig_str)
43 - 2*sum(ave_ms_power) / sum(power_denom1)
AVE_TCH_AVAIL_HALF
ave_ms_power,
p_nbsc_res_avail
43 - 2*sum(ave_bs_power) / sum(power_denom2)
ave_bs_power, p_nbsc_power <10
sum(ave_dl_sig_str) / sum(power_denom3) - 110
ave_dl_sig_str,
sum(ave_ul_sig_str) / sum(power_denom4) - 110
ave_ul_sig_str,
Instructions Operation Required Currnent Value Self-Check NOTES
Judge Call drop reason:

TOPN cell or Whole network
if TOPN cell , then perform TOPN Cell
action2
0.50% 2.10%
Self-Check(Existing
Instructions NOTES
or not?)
a alarm: according to the alarm information
ntenna Existing
he replacement of TRX Not Existing
ness warning: restart Not Existing
errupt service : Maintenance Based on
tion Not Existing
ence alarm: find the interference Not Existing
ocation failure alarm: the replacement of the
Not Existing
l congestion alarm: open half rate or capacity
on channel Not Existing
or cell configuration error alarm: according to
m additional information processing Not Existing
arm: change alarm hardware Not Existing
tion transfer view fault Not Existing
r PCU to solve the switching Not Existing
Not Existing
Not Existing
Influence When
Operation Required Currnent Value Self-Check NOTES
Decreased
Added drop call
0
Reduce traffic to enter
MS enter /prevent
0
0
Reduced cell phone
(900M) transmit power
Reduced cell phone
Reduced cell phone
Reduced
When thecell phone
mobile phone
(1800M)
is transmit
connected power
to the
Increase
When coverage,
900M network, thephone
the mobile
reduce
is service
connected to quality
the
maximum transmission
1800M
power network,
is reduced,thethe
maximum
coveragetransmission
is reduced,
power
and theisnetwork
reduced,uplink
the
Increase
coverage the 900M cell
is reduced,
bottom noise is
emission
and power, reduce
the network
reduced. uplink
Increase
the the
coverage
bottom 1800M
noise is cell
emission
reduced. power, reduce
the
Cellcoverage
can be reduced
power range
0
0
errors can cause the network to be unable to access
0
e return of investment in GSM network, no need to replace the existing equipment or any hardware
and hence the mobiles experience better radio conditions.
e effective optimization effect
ent to the same traffic energy savings of 15%
Radio Frequency (RF) modules and also helps in network planning.
e coverage or capacity individually which results in flexibility.

costs by reducing energy consumption. In Flexi EDGE BTS, the operator saves around 40 W by powering down one dual TRX.
"Action 3.2: Radio

Enviroment Analysis"
go to "Action 3.5:
Handover Analysis"
go to "action3.2: Radio
Enviroment Analysis" and
"Action 6: Transmission
Anaysis"
If the A interface drop even

distributed in all areas of
BSC,
1 Youthen
can the basicthrough
observe A
interface
the ZAHP circuit
command is a fault
reset
A interface dropped
carrier
generally
2 If trx reset no used MSC
due to cross
caused by the
,rebuilding thehandover,
trx to the
need to check the action
observation
2.2&3.5
3 The above is invalid to
confirm whether the trx fault
or transmission data
configuration error
4 If TR drop evenly
go to "action2.1:
distributed AlarmBSC,
in a certain
may be TC or BCS other unit
Checking"
fault (2992/2993), through
the alarm
there manualsome
are always processing
alarm
related, then go to "Action
2.1：Alarm checking" to
check alarm
go to "action3.4:
Transmission Analysis"
When locking the cell,

customer must be forced to
handover to other cell
there are always some alarm
related, then go to "Action
2.1：Alarm checking" to
check alarm
Investigation of interference and hardware failure

Weak coverage :check cell
transmit power, adjust the
antenna, replaced by the
high gain antenna, add the
pull far cell
check
,add new cell transmit
station
power, adjust the
antenna, replaced by
the high gain antenna,
add the pull far cell
,add new station
Adjust the antenna or reduce cell power. ZEUG:SEG=X,PMAX2=4;

1 Check frequency interference
2, whether the cell with repeater
3, check frequency
1 Check the districtinterference
4,
2, check thethe
whether trxcell
level quality,
with determine the trx hardware issue or frequency issue
repeater
3, Check whether external interference caused by the investigation of interference sources
4, check the district TA, whether overshooting
1
5,Check
check frequency interference
the trx level quality, determine the trx hardware issue or frequency issue
The drop is higher and the poor quality can exchange frequency, locking trx, modify frequency, replace TRX
1 frequency problem, change the frequency

2 TRX problem, change TRX
1 single carrier frequency interference, frequency issue or TRX may be a hardware problem
2 all carrier interference may be outside interference or repeater reason
TCH congestion
1 See whether the
hardware failure or TCH
availability
2 burst traffic congestion,
observation
tuning FRL,FRU
PI=Y,REO,PET
parameter RXP,PMAX1
6 expansion
SD congestion
1, view the hardware alarm
or SD available
2 IF cell is in border and
2, the expansion of SD
channel
3, open dynamic SD
4, open enhanced dynamic
SD
Inform the customer to

check transmission
the hardware
Check which cell have,clock
low success rate.
issue,Interference
1、interference issueproblem,
Action 2,3,4 issue
2、hardware
3、frequency issue
4、missing Neighbor
5、Wrong define adj parameter
6、overshooting
7、Check Parameter SL,AUCL,EPB,BLT,PRI,OF,SYNC,PMRG,LMRG,QMRG
8、Inter-plmn
Handover failurecheck
due whether Add Neighbor
to congestion LAC cell
of the target in MSC
9、Inter-plmn check Target side whether have 1~7 issue
Handover failure due to congestion of the cell
CONFIGURATION CHANNEL
On behalf of the hardware

may be a failure to check the
alarm, according to the
alarm processing manual for
processing.
TBF建立成功率 TBF ESTABLISHMENT SUCCESS RATE D
KPI Name(English Name)
Determine whether TBF

establishment rate occurs on TBF ESTABLISHMENT SUCCESS RATE
some top cells or the entire TBF建立成功率
network.
Step1: Demarcation

write donw in D5 like the TBF建立成功率-India TBF ESTABLISHMENT SUCCESS RATE
demo

Alarm ID Alarm Name
7604 BTS OPERATION DEGRADED
7606 TRX FAULTY
7738 BTS WITH NO TRANSACTIONS
7767 BCCH MISSING
Mandatory checking 7744 EXCESSIVE TCH INTERFERENCE
7745 CHANNEL FAILURE RATE ABOVE DEFIN
7746 CH CONGESTION IN BTS ABOVE DEFIN
7725 TRAFFIC CHANNEL ACTIVATION FAILUR
3033 UNKNOWN ROUTING AREA OR LOCATION
3068 EGPRS DYNAMIC ABIS POOL FAILURE
3073 FAULTY PCU PCM TIMESLOTS IN PCU
3164 PCU PROCESSOR OVERLOAD ALARM
Except above, if other alarms 3273
exist, please list them here EGPRS TERRITORY FAILURE
7730 CONFIGURATION OF BCF FAILED

参数名称
Paramter Name ABBREV
EGPRS Init MCS Ack Mode MCA
MCU
EGPRS Init MCS Un Ack Mode
alpha ALPHA
gamma GAMMA
defaultGPRScapacity CDEF
dedicatedGPRScapacity CDED
gprsEnabled GENA
EGPRSEnabled EGENA
maxGPRScapacity CMAX
trxPriorityInTCHAlloc TRP
preferBCCHFreqGPRS BFG
ELA
EGPRS Link Adaptation Enabled
Step2:Checking
mean BEP offset 8PSK MBP
GPRSenabledTRX GTRX
msTxPwrMax *GSM*dBm PMAX1
msTxPwrMax *DCS*dBm PMAX2
minMSTxPower *GSM*dBm PMIN

minMSTxPower *DCS*dBm PMIN
rxLevAccessMin RXP
gprsRxlevAccessMin GRXP
msTxPwrMaxCCH *GSM*dBm TXP1

msTxPwrMaxCCH *DCS*dBm TXP2
bsTxPwrMax *GSM*dBm PMAX1
bsTxPwrMax *DCS*dBm PMAX2
bsTxPwrMin PMIN
gprsDlPcEnabled DLPC
dlpcwindowsize PCWC
dlpcpowerreduction PCPOW
dlpc8pskbeptarget PCPSK
dlpccitarget PCCI

OSC Half Rate with SAIC MS Orthogonal subchannel (OSC) is a feature that in
Dynamic PCU2 Pooling Dynamic PCU2 Pooling” feature reallocates segmen
Extended Cell for Data through this function to achieve the expansion of
Energy Saving mode for BCCIn the "Energy saving mode for BCCH TRX" feature
Double Power TRX for 2G BTDouble Power TRX for 2G BTS (BSS20870), is a licence based application softwar
Flexible MCPA TX Power PooThe Flexi Multiradio BTS RF Module (FXxx) has t
(E)GPRS DL Power Control The (E)GPRS Downlink (DL) Power Control feature
PCU2 Basic SW per 256 ch (A0
Action 3.1: Identify TBF establishments fail cause

上行TBF建立成功率% UL TBF ESTABLISHMENT SUCCESS RATE
The number of uplink GPRS TBF

UL ISSUE 由于手机没有响应上行GPRSestablishments
TBF建立失败次数 that have failed due to no
response from MS. This counter does not
The number of uplink EGPRS TBF
consider
由于手机没有响应上行EGPRS EGPRS TBFs.
TBF建立失败次数
establishments that have failed due to no
response from MS.
下行TBF建立成功率% DL TBF ESTABLISHMENT SUCCESS RATE
The number of downlink GPRS TBF
DL ISSUE 由于手机没有响应下行GPRS TBF建立失败次数
response from MS. This counter does not
consider
The EGPRS
number TBFs. EGPRS TBF
of downlink
由于手机没有响应下行EGPRS TBF建立失败次数
response from MS.
Action 3.2: No resource
CS resource condition TCH全速率话务 Average FTCH traffic
下行TBF阻塞率 DL mlslot allocation blocking rate
PS resource condition
上行TBF阻塞率 UL mlslot allocation blocking rate
下行PDCH复用度 AVERAGE DL TBFS PER TSL
上行PDCH复用度 AVERAGE UL TBFS PER TSL

PS resource condition
Step3: Anylysis TCH争夺PDCH次数 Number of GPRS territory downgrades made becaus
PDCH平均可用数 AVERAGE NUM OF PDCH
占用的PDCH的最大数目 The peak number of radio time slots delivered f
动态PDCH配置时隙数 Default_GPRS_CAPACITY
静态PDCH配置时隙数 DEDICATED_GPRS_CAPACITY
Action 3.3: no responding

下行电平质量分布 DL LEV & QUAL Distribute KPI
上行电平质量分布 UL LEV & QUAL Distribute KPI


MCS-7、8、9 编码RLC块在EGPRS
MCS7~9 code rate
RLC块中所占的比例

Description
Counter/Formula Tables Name Reference Value
100*sum(NBR_OF_DL_TBF+NBR_OF_UL_TBF-
DL_TBF_ESTABLISHMENT_FAILED-
DL_EGPRS_TBF_REL_DUE_NO_RESP-UL_TBF_Establishment_Failed- P_NBSC_PACKET_CONTROL_ >98%
UL_EGPRS_TBF_REL_DUE_NO_RESP)/sum(NBR_OF_DL_TBF+NBR_ UNIT
OF_UL_TBF)


Major 0 information
Major 0 TRX
Medium 0 Related to SGSN side, LAC/RAC configuration error
Medium 0 Configuration or hardware, PCU capacity will reduce
Medium 0 GSWB hardware issues, PCU capacity will reduce
Medium 0 PCU load is high, if the need to adjust
Medium 0 Congestion due to insufficient PCU resources
Medium 0 BCF configuration and hardware does not match

(1…9) 7 But for the C/I high ar
(1…9) 6 "To improve the rate,
7 (GSM 900)
(0…10) The greater the ALPHA,
8 (GSM1800)
34 (GSM 900)
(0…62) The larger the GAMMA
36 (GSM1800)
(1…100%) 50 Increase the number o
(0…100%) 1 Increase the number of
(Y/N) Y 0
(Y/N) Y 0
(0…100%) 100 Increase the number o
(0…2) 0 According to the actu
(Y/N) N The GPRS channel is g
(0,1,2) 2 Link adaptation
(-31…31) 0 Can increase the high
Y/N Y 0
(-110…-47)dBm -102~-98 Reduce coverage, impr
(-110...-47) -98 Reduce coverage, improve service quality
(5…43 step 2) *GSM*dBm 33 When the mobile phone
(0…30 step 2) *DCS*dBm 30 When the mobile phone
(0…30 step 2)DB 0 Reduce the 900M area
(0…30 step 2)DB 0 Reduce the 1800M are
(0…30 step 2)DB 20 Cell can reduce the p
(Y/N) Y Reduce downlink inter
0...10 dB, step 2
8 This parameter define
dBm
0...10 dB, step 3
4 After the TBF is establ
dBm
The greater the value, the lower the EGPRS downlink power co
0...31, step 1 17
The greater the value, the GPRS downlink power control is abo
0...30 dB, step 1 dB 12
Cell Checking and Analysis functions
•The feature is applicable with existing GSM SAIC handsets, thus providing an immediate gain with just a software upgrade in the GSM radio network.
Adapted
•It increasesScenario
the capacityand Gain
for voice and releases capacity for data traffic without requiring new TRXs or related hardware. This reduces the number of TRXs
•Improvement
•The increasedincapacity
BSC PCU perutilization
TRX reduces factor.
the energy consumption per user. This reduces the energy consumption required per Erlang significantly.
•Reduction
•It avoids thein need
CAPEX investments.
to add new sites, as it maintains the coverage area in capacity extensions.
•Increase in revenue
•The increased dueper
capacity to decreased PS call
TRX effectively drops site
reduces caused by athrough
density single PCU capacity
reduced limitation.
combining losses.
•OPEX saving as
•When another radio
radio network resource
technology needs toallocation
share the is donesite,
same automatically.
antennas or input ports of combiners may be released by the introduction of OSC Half Rate
•More accurate PCU pool analysis in the PCU selection algorithm.
When this feature is activated in the network, most of the energy savings are provided by the dummy burst power reduction during periods of low traffic, e.g
reduced MCPA
The Flexible transmitTXpower
Power ofPooling
dummy feature
bursts, provides
and the limited dynamic
the following power to
benefits control allowed for active CS channels, result in a reduction in downlink interfe
operators:
Increase
•It allows cover distanceto utilize the output power of the MCPAs optimally.
the operators
•It increases the capacity of the BTS for a given coverage area without the need ofadditional Radio Frequency (RF) modules and also helps in network plan
The (E)GPRS
•It reduces the DL
callPower Control
drop rate feature provides
in coverage the following benefits to the operator:
limited networks.
•It
•It reduces transmit
enables the power,
user to which
enhance in turn helps
coverage in reducing
and capacity thesame
at the interference
time. It in theenhances
also network, the
andcoverage
hence theormobiles experience
capacity better
individually whichradio conditions.
results in flexibility.
to
•It enhance
maintainsPCUvoicecapacity
quality when the data usage increases.
100*(NBR_OF_UL_TBF-UL_TBF_ESTABLISHMENT_FAILED- P_NBSC_PACKET_CONTROL_
UL_EGPRS_TBF_REL_DUE_NO_RESP)/NBR_OF_UL_TBF UNIT >98%
P_NBSC_PACKET_CONT
UL_TBF_ESTABLISHMENT_FAILED 0
ROL_UNIT
P_NBSC_PACKET_CONT
UL_EGPRS_TBF_REL_DUE_NO_RESP 0
ROL_UNIT
100*(NBR_OF_DL_TBF-DL_TBF_ESTABLISHMENT_FAILED- P_NBSC_PACKET_CONTROL_
DL_EGPRS_TBF_REL_DUE_NO_RESP)/NBR_OF_DL_TBF UNIT >98%
P_NBSC_PACKET_CONTROL_
DL_TBF_ESTABLISHMENT_FAILED UNIT 0
DL_EGPRS_TBF_REL_DUE_NO_RESP P_NBSC_PACKET_CONT
0
ROL_UNIT
a = p_nbsc_traffic <2%
b = p_nbsc_ho
sum(ave_busy_tch / res_av_denom14) p_nbsc_res_avail >0
succ_a_int_circ_type))]
SUM(AVE_BUSY_TCH/RES_AV_DENOM14)/
(SUM(AVE_AVAIL_TCH_SUM/AVE_AVAIL_TCH_DEN) >0.1
+SUM(AVE_GPRS_CHANNELS_SUM/AVE_GPRS_CHANNELS_DEN)- p_nbsc_res_avail
CH_DEN)) >0
AVE_BUSY_GPRS_CH_DL/AVE_BUSY_GPRS_CH_DEN p_nbsc_packet_control_unit
sum(NO_RADIO_RES_AVA_DL_TBF) /
UM(REQ_1_TSL_DL+REQ_2_TSL_DL+REQ_3_TSL_DL+REQ_4_TSL_D p_nbsc_packet_control_unit <1%
L+REQ_5_TSL_DL+REQ_6_TSL_DL+REQ_7_TSL_DL+REQ_8_TSL_DL)
sum(NO_RADIO_RES_AVA_UL_TBF)
/sum(req_1_tsl_ul+req_2_tsl_ul+req_3_tsl_ul+req_4_tsl_ul+req_5 p_nbsc_packet_control_unit <1%
_tsl_ul+req_6_tsl_ul+req_7_tsl_ul+req_8_tsl_ul)
sum(aver_tbfs_per_tsl_dl_sum) /sum(aver_tbfs_per_tsl_dl_den) * p_nbsc_packet_control_unit
100 <3
sum(aver_tbfs_per_tsl_ul_sum) /sum(aver_tbfs_per_tsl_ul_den) *
p_nbsc_packet_control_unit <2
100
GPRS_TER_DG_DUE_INC_IN_CSW_TR P_NBSC_TRAFFIC 0
if(x>Default_GPRS_
decode(floor(cdef *gtchch / 100),0,1,floor(cdef * gtchch / 100)) CAPACITY,Default_
CDEF:c_bsc_bts.BTS_DGS_92 AVE_GPRS_CHANNELS_DEN) P_NBSC_RES_AVAIL GPRS_CAPACITY=
gtchch:sum(decode(TRX_GPRS_ENA_TRX,1, x,Default_GPRS_CA
decode(floor(cded*gtchch
decode(ch.trx_ch_0_type,0,1,2,1,0)/ 100),0,1,floor(cded * gtchch / 100)) PACITY)
PEAK_GPRS_CHANNELS
CDED:c_bsc_bts.BTS_DGS_91 P_NBSC_RES_AVAIL
+ decode(ch.trx_ch_1_type,0,1,2,1,0)
gtchch:sum(decode(TRX_GPRS_ENA_TRX,1,
+ decode(ch.trx_ch_2_type,0,1,2,1,0) Counters from table(s):
decode(ch.trx_ch_0_type,0,1,2,1,0)
+ decode(ch.trx_ch_3_type,0,1,2,1,0) a = c_bsc_bts
++ decode(ch.trx_ch_1_type,0,1,2,1,0)
decode(ch.trx_ch_4_type,0,1,2,1,0) b=c_bsc_trx
decode(ch.trx_ch_5_type,0,1,2,1,0) Counters from table(s):
decode(ch.trx_ch_6_type,0,1,2,1,0) a = c_bsc_bts
decode(ch.trx_ch_7_type,0,1,2,1,0),0)) b=c_bsc_trx
+Fromdecode(ch.trx_ch_5_type,0,1,2,1,0)
+c_bsc_trx
+sum over a range (class_upper_range)
decode(ch.trx_ch_7_type,0,1,2,1,0),0)) Counters from table(s): level [-80,-47]:qual
(freq_dl_qual0+freq_dl_qual1+freq_dl_qual2+freq_dl_qual3+freq_
From p_nbsc_rx_statistics [6~7] proportion<5%
dl_qual4
c_bsc_trx
(freq_ul_qual0+freq_ul_qual1+freq_ul_qual2+freq_ul_qual3+freq_ p_nbsc_rx_statistics [6~7] proportion<5%
sum over all ranges
ul_qual4
100*(SUM(freq_ul_qual0+freq_ul_qual1+freq_ul_qual2+freq_ul_q
(freq_dl_qual0+freq_dl_qual1+freq_dl_qual2+freq_dl_qual3+freq_
P_NBSC_RX_STATISTICS <3%
ual3+freq_ul_qual4+freq_ul_qual5+freq_ul_qual6+freq_ul_qual7)
dl_qual4
sum
Whereover all ranges
100*(SUM(freq_dl_qual0+freq_dl_qual1+freq_dl_qual2+freq_dl_q
(freq_ul_qual0+freq_ul_qual1+freq_ul_qual2+freq_ul_qual3+freq_
P_NBSC_RX_STATISTICS <3%
CLASS_UPPER_RANGE<=15)/SUM(freq_ul_qual0+freq_ul_qual1+fre
ual3+freq_dl_qual4+freq_dl_qual5+freq_dl_qual6+freq_dl_qual7)
ul_qual4
q_ul_qual2+freq_ul_qual3+freq_ul_qual4+freq_ul_qual5+freq_ul_q
WHERE
+freq_ul_qual5+freq_ul_qual6+freq_ul_qual7) Counters from table(s):
ual6+freq_ul_qual7)
CLASS_UPPER_RANGE<=20)/SUM(freq_dl_qual0+freq_dl_qual1+fre
TA=0 p_nbsc_timing_advance TA>5 ratio<20%
q_dl_qual2+freq_dl_qual3+freq_dl_qual4+freq_dl_qual5+freq_dl_q
TA=1
ave_ms_bs_dist
ual6+freq_dl_qual7) p_nbsc_timing_advance urban: 0~2
…….
100*sum(freq_dl_qual0+freq_dl_qual1+freq_dl_qual2+freq_dl_qua surban:2~4
TA=63
l3+freq_dl_qual4)/sum(freq_dl_qual0+freq_dl_qual1+freq_dl_qual Counters from table(s):
100*Sum(Ave_Idle_f_Tch_4/Res_Av_Denom7+Ave_Idle_h_Tch_4/
2+freq_dl_qual3+freq_dl_qual4+freq_dl_qual5+freq_dl_qual6+freq p_nbsc_rx_qual >94%
100*sum(freq_ul_qual0+freq_ul_qual1+freq_ul_qual2+freq_ul_qua
Res_Av_Denom12+Ave_Idle_f_Tch_5/Res_Av_Denom8+Ave_Idle_h
(freq_reports)/
_dl_qual7)
l3+freq_ul_qual4)/sum(freq_ul_qual0+freq_ul_qual1+freq_ul_qual
_Tch_5/Res_Av_Denom13)/ Counters from table(s):
sum over all ranges >94%
2+freq_ul_qual3+freq_ul_qual4+freq_ul_qual5+freq_ul_qual6+freq
(Sum(Ave_Idle_f_Tch_1/Res_Av_Denom4+Ave_Idle_h_Tch_1/Res_
(freq_reports) p_nbsc_rx_qual
_ul_qual7)
Av_Denom9)+Sum(Ave_Idle_f_Tch_2/Res_Av_Denom5+Ave_Idle_h Counters from table(s):
_Tch_2/Res_Av_Denom10)+Sum(Ave_Idle_f_Tch_3/Res_Av_Deno p_nbsc_res_avail <5%
m6+Ave_Idle_h_Tch_3/Res_Av_Denom11)+Sum(Ave_Idle_f_Tch_4
Sum over MCS 7-
/Res_Av_Denom7+Ave_Idle_h_Tch_4/Res_Av_Denom12)+Sum(Ave
9(DL_RLC_Blocks_In_Ack_Mode+UL_RLC_Blocks_In_Ack_Mode)/Su
p_nbsc_coding_scheme >60%
_Idle_f_Tch_5/Res_Av_Denom8+Ave_Idle_h_Tch_5/Res_Av_Deno
m over MCS 1-9(DL_RLC_Blocks_In_Ack_Mode+
m13))
UL_RLC_Blocks_In_Ack_Mode)
NOT_AVAIL_TIME
ERR_SEC P_NBSC_ET_BSC
ERR_SEC_SEVER
Instructions Operation Required Currnent Value Self-Check NOTES
Judge TBF establishment

rate reason: TOPN cell or
Whole network TOPN Cell
if TOPN cell , then perform
action2
Self-Check(Existing
Instructions NOTES
or not?)
a alarm: according to the alarm information
ntenna Existing
he replacement of TRX Not Existing
ness warning: restart Not Existing
errupt service : Maintenance Based on
tion Not Existing
ence alarm: find the interference Not Existing
ocation failure alarm: the replacement of the
Not Existing
l congestion alarm: open half rate or capacity
on channel Not Existing
r PCU to solve the switching Not Existing
to SGSN side, LAC/RAC configuration error Not Existing
ration or hardware, PCU capacity will reduce Not Existing
hardware issues, PCU capacity will reduce
d is high, if the need to adjust
tion due to insufficient PCU resources
nfiguration and hardware does not match Not Existing
Not Existing
Not Existing
"But for the C/I poor
Influence
area is set When
smaller to Operation Required Currnent Value Self-Check NOTES
Decreased
improve the success
rate
The of the
smaller
"Reduce the the
rate,ALPHA,
can
establishment
the smallerthetheofslope
guarantee TBF,
thus
is, increasing
the more the
diffuse
efficiency of data
EDGE
the coverage
transmission
transmission power
The smaller
of the mobilethephone
GAMMAis
value,
with thethechange
greaterof the
the
Reducing the
transmission dynamic
received fieldpower of
PDCH,
the will increase
mobile
strength. phone. the
access
Reducedfailure
static caused
PDCH,
by
willnoincrease
resourcesaccess to
failure
0
0
Reduced dynamic PDCH,
will increase access to
failure
0
0
Reduce the high 0

encoding ratio,
increase the anti-
interference ability 0
Reduced cell phone
Reduced cell phone
Reduced cell phone
Reduced cell phone
Increase
When coverage,
the mobile phone
reduce
is servicetoquality
connected the
When
900M the
e coverage, improve mobile
network,
service thephone
quality
is connected
maximum to the
transmission
1800M
power network,
is reduced, thethe
maximum
is reduced,
power
and theisnetwork
reduced,uplink
the
Increase
coverage
bottom noise the 900M
is reduced,
is cell
emission
and power, reduce
the network uplink
reduced.
Increase
the
bottom the 1800M
coverage
noise is cell
emission
Thiscoverage
the
Cell parameter defines
ThisPScan
the
be reduced
value is about
downlink power
power
small,
After range
EGPRS
the TBF downlink
is
control
This valuerelative
isthe to
about
power control
established,
full power amplitude
emission 0
small,
is about
initial GPRS downlink
deep,
power the
control
maximumcontrol
power power amplitude
down
interference
is carried
control outeffect
the is
is aboutrange,
better, deep,thethe
smaller but
according
interferencethetothe
power PCPOW
effect is
corresponding
parameter
control but impact
setting
amplitude is on
better,
the
value,datathe the
service
smaller is the
smaller
corresponding impactis, on
greater.
interference The rate
effect
the
the data
priority
smallerservice
the isisset
scheme
greater.
to 29, andThetherate
interference poweris
effect
priority schemeisisset
control scheme set
to
to 17, and the power
20, and the
control
compromise scheme
schemeis set
is
to
set15,to and
17. the
compromise scheme is
set to 15.
just a software upgrade in the GSM radio network.

s or related hardware. This reduces the number of TRXs required to realize a specific capacity or spectral efficiency.
gy consumption required per Erlang significantly.
s.
s may be released by the introduction of OSC Half Rate with SAIC MS.
ors to reduce network operating costs.

my burst power reduction during periods of low traffic, e.g. at night time. With dynamic power control of active dedicated channels, the feature reduces electricity consumpti
ctive CS channels, result in a reduction in downlink interference caused by the BCCH frequency.
Frequency (RF) modules and also helps in network planning.

ce theormobiles
rage experience
capacity better
individually whichradio conditions.
results in flexibility.
TCH congestion
1 See whether the
hardware failure or TCH
availability
observation
tuning FRL,FRU
PI=Y,REO,PET
parameter RXP,PMAX1,RLT
6 expansion
SD congestion
or SD available
2, PDCH congestion
the expansion of SD
1 See whether the
channel
hardware failure
3, open dynamic SD
2 open
4, burst enhanced
traffic congestion,
dynamic
observation
SD
tuning FRL,FRU
PI=Y,REO,PET
parameter GRXP,PMAX1
6 Increace
CDED,CDEF,CMAX
7 expansion
PDCH congestion
1 See whether the
hardware failure
observation
tuning FRL,FRU
PI=Y,REO,PET
parameter GRXP,PMAX1
6 Increace
CDED,CDEF,CMAX
7 expansion
Weak coverage :check cell

Investigation
transmit of interference
power, adjust the and hardware failure
high gain antenna, add the
check
pull far cell
cell transmit
power,
,add newadjust
station the
antenna, replaced by
the high gain antenna,
add the pull far cell
,add new station

1 Check frequency interference
1
3,Check
check frequency
the districtinterference
2,
4, whether
check thethe
trxcell
levelwith repeater
quality, determine the trx hardware issue or frequency issue
4, check the district TA, whether overshooting
1
5,Check
the trx level quality, determine the trx hardware issue or frequency issue
This index reflects the quality of the PDTCH channel, including the wireless environment of the network
Inform the customer to

check transmission
e reduces electricity consumption throughout the day.
TBF掉线率 TBF Drop rate Descrip
Required Steps Required Actions KPI 名称(Chinese Name) KPI Name(English N
occurs on some top cells or TBF掉线率 TBF Drop RATE
the entire network.
Step1: Demarcation
with the one in D4, please UL TBF Drop RATE-India
write donw in D5 like the UL TBF掉线率--印度
demo

Alarm ID Alarm Name
7604 BTS OPERATION DEGRAD
7606 TRX FAULTY
7738 BTS WITH NO TRANSACT
7767 BCCH MISSING
Mandatory checking
7744 EXCESSIVE TCH INTERF
7745 CHANNEL FAILURE RATE
7746 CH CONGESTION IN BTS
7725 TRAFFIC CHANNEL ACTIV
8099 RECEIVED BIT ERROR RATI
Except above, if other alarms


参数名称
Paramter Name ABBREV
EGPRS Init MCS Ack Mode MCA
EGPRS Init MCS Un Ack Mode MCU
alpha ALPHA
gamma GAMMA
defaultGPRScapacity CDEF
dedicatedGPRScapacity CDED
gprsEnabled GENA
EGPRSEnabled EGENA
maxGPRScapacity CMAX
trxPriorityInTCHAlloc TRP
preferBCCHFreqGPRS BFG
EGPRS Link Adaptation Enabled ELA
mean BEP offset 8PSK MBP
GPRSenabledTRX GTRX
temporaryOffset TEO
cellReselectParamInd PI
cellReselectOffset REO
Step2:Checking
cellReselectHysteresis HYS
msTxPwrMax *GSM*dBm PMAX1
msTxPwrMax *DCS*dBm PMAX2
minMSTxPower *GSM*dBm PMIN

minMSTxPower *DCS*dBm PMIN
rxLevAccessMin RXP
msTxPwrMaxCCH *GSM*dBm TXP1
msTxPwrMaxCCH *DCS*dBm TXP2
bsTxPwrMax *GSM*dBm PMAX1
bsTxPwrMax *DCS*dBm PMAX2
bsTxPwrMin PMIN
gprsDlPcEnabled DLPC
dlpcwindowsize PCWC
dlpcpowerreduction PCPOW
dlpc8pskbeptarget PCPSK
PCCI
dlpccitarget

Dynamic PCU2 Pooling Dynamic PCU2 Pooling” feature
Extended Cell for Data through this function to achiev
Energy Saving mode for BCCH TRX In the "Energy saving mode for
Double Power TRX for 2G BTS (BSS20870), is a licence based application so
Double Power TRX for 2G BTS
Flexible MCPA TX Power Pooling The Flexi Multiradio BTS RF M
Dynamic Frequency and Channel Alloca0
STIRC STIRC is designed to cancel upl
Adjustable Intelligent Shutdown 2G BT0
2G TRX Automatic Power Down 2G automatic power down" featu
PCU2 Basic SW per 256 ch (Abis 16kbit/0
Action 3.1: Identify call drop causes

上行TBF掉线率% UL TBF ESTABLISHMENT SUCCE
因为CS话务导致的上行掉线 UL TBF REL DUE CSW

TRAFFIC
UL ISSUE 因为手机无响应导致的上行掉线 UL TBF REL DUE NO
RESP MS
因为小区重选导致的上行掉线 UL TBF REL DUE TO
FLUSH
因为手机挂起导致的上行掉线 UL TBF REL DUE TO
SUSPEND
下行TBF掉线率% DL TBF ESTABLISHMENT SUCCE
因为CS话务导致的下行掉线 DL TBF REL DUE CSW

TRAFFIC
DL ISSUE 因为手机无响应导致的下行掉线 DL TBF REL DUE NO
RESP MS
因为小区重选导致的下行掉线 DL TBF REL DUE TO
FLUSH
因为手机挂起导致的下行掉线 DL TBF REL DUE TO
SUSPEND
下行电平质量分布 DL LEV & QUAL Distribute
上行电平质量分布 UL LEV & QUAL Distribute


MCS-7、8、9 编码RLC块在EGPRS RLC块中所占的比例

MCS7~9 code rate
Step3: Anylysis TRX 级下行RLC/MAC重传率 RLC/MAC Retransmission Rate
(TRX Level) Coverage and Interference Analysis TRX Quality
载频级4~5级干扰占比 TRX interference

下行PDCH复用度 AVERAGE DL TBFS PER TSL
上行PDCH复用度 AVERAGE UL TBFS PER TSL
TCH争夺PDCH次数 Number of GPRS territory downg
PDCH平均可用数 AVERAGE NUM OF PDCH
占用的PDCH的最大数目 The peak number of radio time
动态PDCH配置时隙数 Default_GPRS_CAPACITY
静态PDCH配置时隙数 DEDICATED_GPRS_CAPACITY


Description
Counter/Formula Tables Name Reference Value Instructions
100*sum(UL_TBF_REL_DUE_NO_RESP_MS+DL_TBF_REL_DUE_NO_
RESP_MS)/sum(NBR_OF_UL_TBF-
UL_TBF_ESTABLISHMENT_FAILED-
UL_EGPRS_TBF_REL_DUE_NO_RESP+NBR_OF_DL_TBF- P_NBSC_PACKET_CONTROL_
DL_TBF_ESTABLISHMENT_FAILED- UNIT <2%
DL_EGPRS_TBF_REL_DUE_NO_RESP) Judge Call drop reason:
TOPN cell or Whole network
action2


Major 0 information
Major 0 TRX
"But for the C/I poor

Influence
area is set When
smaller to
Decreased
improve the success
(1…9) 7 But for the C/I high ar The
ratesmaller
of the
"Reduce the the
rate,ALPHA,
can
establishment
the smaller theofslope
TBF,
(1…9) 6 "To improve the rate, guarantee
thusthe
is,
the
increasing
more the
efficiency ofdiffuse
data
7 (GSM 900) EDGEtransmission
the coverage
transmission power
(0…10) The greater the ALPHA, The smaller the GAMMAis
8 (GSM1800) of the mobile phone
34 (GSM 900) value,
with the change of the
the greater the
(0…62) The larger the GAMMA Reducing
36 (GSM1800) received the
transmission
field dynamic
power of
(1…100%) 50 PDCH,
the will
mobile
Increase the number ostrength. increase
phone. the
access failure
Reduced caused
static PDCH,
(0…100%) 1 Increase the number of by noincrease
will resources access to
failure
(Y/N) Y 0 0
(Y/N) Y 0 0
Reduced dynamic PDCH,
(0…100%) 100 Increase the number owill increase access to
failure
(0…2) 0 According to the actu 0
(Y/N) N The GPRS channel is g 0
(0,1,2) 2 Link adaptation Reduce the high 0
(-31…31) 0 Can increase the highencoding ratio,
increase the anti-
Y/N Y 0 interference ability
Defined in the time of 0
(0…70 step 10)dB 0 Defined in the time of PET, the temporary
offset value of the C2
(Y/N) Y 0 temporary. 0
(0…126 step 2)dB 0 Reduce traffic to
IDLE state is more likeThe boundary of theenter
MS enter /prevent
(0…14,step 2dB)dB 10 Under the condition oflocation area reduced
cell reselection
(5…43 step 2) *GSM*dBm 33 Reduced cell phone
Increase the transmis difficulty
(0…36 step 2) *DCS*dBm 30 Increase the transmis Reduced cell phone
(5…43 step 2) *GSM*dBm 5 Increase the transmis Reduced cell phone
(0…36 step 2) *DCS*dBm 0 Reduced
Increase the transmis When thecell
mobilephone
phone
(1800M)
is transmit
connected to thepower
(-110…-47)dBm -102~-98 Reduce coverage, impr Increase
When the coverage,
900M network, thephone
mobile
reduce
is service
connected to
maximum transmissionquality
the
(5…43 step 2) *GSM*dBm 33 When the mobile phone 1800M
power network,
is reduced, thethe
maximum
is reduced,
(0…30 step 2) *DCS*dBm 30 When the mobile phone power
and theisnetwork
reduced,uplink
the
Increase
coverage the 900M
is cell
is reduced,
bottom noise
(0…30 step 2)DB 0 Reduce the 900M areaemission
and power, reduce
the network
reduced. uplink
Increase
the the 1800M
coverage
bottom noise is cell
(0…30 step 2)DB 0 Reduce the 1800M areemission
Thiscoverage
the parameter defines
(0…30 step 2)DB 20 Cell can reduce the p Cell
the
can be reduced
PSrange
downlink power
power
After the TBF is to
control relative
(Y/N) Y Thispower
valueemission
Reduce downlink interestablished,
full isthe
about 0
0...10 dB, step 2 small,
initial
maximum GPRS
power
powerdownlink
control
down
8 This parameter definepower
is control
carried outamplitude
dBm control range, the
0...10 dB, step 3 is aboutthe
deep, thethePCPOW
4 After the TBF is establaccording
smaller
interference
topower
dBm parameter setting isis
effect
The greater the value,control
the lower
better,
value,
amplitude
the
but EGPRS
the downlink power contro
0...31, step 1 17 smallerthe smaller the
The greater the value,corresponding
interference impactpower
effect
the GPRS downlink on control is about sh
is,
0...30 dB, step 1 dB 12 the
the data service
smaller the is
greater. The rate
interference effect is
priority scheme is set
to 20, and the power
control scheme is set
ghbor Cell Checking and Analysis functions to 15, and the
compromise scheme is
set to 15.
•Improvement in BSC PCU utilization factor.

Adapted
•Reduction in Scenario and Gain
CAPEX investments.
•Increase in revenue due to decreased PS call drops caused by a single PCU capacity limitation.
•OPEX saving as radio network resource allocation is done automatically.
•More accurate PCU pool analysis in the PCU selection algorithm.
When this feature is activated in the network, most of the energy savings are provided by the dummy burst power reduction during periods of low traffic, e.g. at n
reduced MCPA
The Flexible transmitTXpower
Power ofPooling
dummy feature
bursts, provides
and the limited dynamic
the following power to
benefits control allowed for active CS channels, result in a reduction in downlink interferenc
operators:
Increase
•It allows cover distanceto utilize the output power of the MCPAs optimally.
the operators
•It increases the capacity of the BTS for a given coverage area without the need ofadditional Radio Frequency (RF) modules and also helps in network planning.
•It enables
improve the user
speech to enhance
quality and MOS coverage
value and capacity at the same time. It also enhances the coverage or capacity individually which results in flexibility.
to enhance the MOS value, reduce the words
energy saving and emission reduction, and reduce network interference
When this feature is activated in the network, the operator can lower the network operating costs by reducing energy consumption. In Flexi EDGE BTS, the oper
to enhance PCU capacity
100*sum(UL_TBF_REL_DUE_NO_RESP_MS)/Sum(NBR_OF_UL_TBF- P_NBSC_PACKET_CONTROL_
UL_TBF_ESTABLISHMENT_FAILED-
UNIT
<2%
UL_EGPRS_TBF_REL_DUE_NO_RESP)
UL_TBF_REL_DUE_CSW_TRAFFIC P_NBSC_PACKET_CONTROL_ 0
UNIT
UL_TBF_REL_DUE_NO_RESP_MS P_NBSC_PACKET_CONTROL_ 0
UNIT
UL_TBF_REL_DUE_TO_FLUSH P_NBSC_PACKET_CONTROL_ 0
UNIT
UL_TBF_REL_DUE_TO_SUSPEND P_NBSC_PACKET_CONTROL_ 0
UNIT
DL:100*sum(DL_TBF_REL_DUE_NO_RESP_MS)/Sum(NBR_OF_DL_T
BF-DL_TBF_ESTABLISHMENT_FAILED- P_NBSC_PACKET_CONTROL_ <2%
DL_EGPRS_TBF_REL_DUE_NO_RESP) UNIT
DL_TBF_REL_DUE_CSW_TRAFFIC P_NBSC_PACKET_CONTROL_ 0
UNIT
DL_TBF_REL_DUE_NO_RESP_MS P_NBSC_PACKET_CONTROL_ 0
UNIT
DL_TBF_REL_DUE_TO_FLUSH P_NBSC_PACKET_CONTROL_ 0
UNIT
DL_TBF_REL_DUE_TO_SUSPEND P_NBSC_PACKET_CONTROL_ 0
UNIT
sum over a range (class_upper_range) Counters from table(s): level [-80,-47]:qual Weak coverage :check cell
Investigation of interference
transmit power, adjust the and hardwar
(freq_dl_qual0+freq_dl_qual1+freq_dl_qual2+freq_dl_qual3+fr p_nbsc_rx_statistics [6~7] proportion<5%
eq_dl_qual4
sum over a range (class_upper_range) Counters from table(s): level [-110,-90]:qual high gain antenna, add the
(freq_ul_qual0+freq_ul_qual1+freq_ul_qual2+freq_ul_qual3+fr p_nbsc_rx_statistics [6~7] proportion<5% pull far cell
sum over all ranges
eq_ul_qual4 ,add new station
eq_dl_qual4
sum over all ranges
(freq_ul_qual0+freq_ul_qual1+freq_ul_qual2+freq_ul_qual3+fr
eq_ul_qual4
check cell transmit
100*(SUM(freq_ul_qual0+freq_ul_qual1+freq_ul_qual2+freq_u P_NBSC_RX_STATISTIC <3% power, adjust the
l_qual3+freq_ul_qual4+freq_ul_qual5+freq_ul_qual6+freq_ul_ S antenna, replaced by
qual7) Where
100*(SUM(freq_dl_qual0+freq_dl_qual1+freq_dl_qual2+freq_d P_NBSC_RX_STATISTIC <3% the high gain antenna,
CLASS_UPPER_RANGE<=15)/SUM(freq_ul_qual0+freq_ul_q S
l_qual3+freq_dl_qual4+freq_dl_qual5+freq_dl_qual6+freq_dl_ add the pull far cell
qual7) WHERE
TA:class_upper_range Counters from table(s): TA>5 ,add new station
Adjust the antenna or reduce cell power.
CLASS_UPPER_RANGE<=20)/SUM(freq_dl_qual0+freq_dl_q
TA=0 p_nbsc_timing_advance proportion<20%
TA=1
ave_ms_bs_dist urban: 0~2
p_nbsc_timing_advance Help to determine the cell coverage distance
l5+freq_dl_qual6+freq_dl_qual7)
……. surban:2~4 1 Check frequency interference
_qual3+freq_dl_qual4)/sum(freq_dl_qual0+freq_dl_qual1+freq
TA=63 Counters from table(s): 2, whether the cell with repeater
>94% 1
3,Check
check frequency
100*sum(freq_ul_qual0+freq_ul_qual1+freq_ul_qual2+freq_ul
sum over a range (class_upper_range) p_nbsc_rx_qual TA, whether overshooting
2,
4, whether
check thethe
trxcell
levelwith repeater
quality, determine the trx ha
_qual3+freq_ul_qual4)/sum(freq_ul_qual0+freq_ul_qual1+freq
(freq_reports)/ Counters from table(s):
>94% 3, Check whether external interference caused by
_ul_qual2+freq_ul_qual3+freq_ul_qual4+freq_ul_qual5+freq_u
sum over all ranges p_nbsc_rx_qual 4, check the district TA, whether overshooting
l_qual6+freq_ul_qual7)
100*Sum(Ave_Idle_f_Tch_4/Res_Av_Denom7+Ave_Idle_h_Tc Counters from table(s):
(freq_reports) 1
5,Check
the trx level quality, determine the trx ha
<5%
p_nbsc_res_avail 2, whether the cell with repeater
Sum over MCS 7-9(DL_RLC_Blocks_In_Ack_Mode+ 3, Check whether external interference caused by
UL_RLC_Blocks_In_Ack_Mode)/Sum over MCS 1- p_nbsc_coding_scheme >60% This index reflects the quality of the PDT
9(DL_RLC_Blocks_In_Ack_Mode+ UL_RLC_Blocks_In_Ack_Mode) 1 frequency problem,
SUM(RETRANS_DL_RLC_MAC_BLOCKS)/SUM(DL_RLC_MAC_BLOCK P_NBSC_RLC_BLOCKS_PER_T change the frequency
S) RX <5%
2 frequency
1 TRX problem, change
problem,
+freq_ul_qual3+freq_ul_qual4+freq_ul_qual5)/sum(freq_ul_qu TRX TCH congestion
（AVE_FULL_TCH_IF4+AVE_HALF_TCH_IF4+AVE_FULL_T change the frequency
al0+freq_ul_qual1+freq_ul_qual2+freq_ul_qual3+freq_ul_qual p_nbsc_rx_qual >95%
CH_IF5+AVE_HALF_TCH_IF5）/ 2 TRX1 problem,
See whether the
change
4+freq_ul_qual5+ TRXhardwarecarrier
failure orfrequency
TCH
（AVE_FULL_TCH_IF1+AVE_HALF_TCH_IF1+AVE_FULL_T 1 single interference,
freq_ul_qual6+freq_ul_qual7) p_nbsc_underlay <5% availability
100*[sum(a.tch_call_req-a.tch_norm_seiz)- 2 all carrier interference may be outside interferen
sum(b.msc_o_sdcch_tch+ .bsc_o_sdcch_tch+b.cell_sdcch_tch) observation
4+AVE_FULL_TCH_IF5+AVE_HALF_TCH_IF5） 3 opening half rate and
a = p_nbsc_traffic <2% tuning FRL,FRU
b = p_nbsc_ho 4 Retuning traffic balance
- sum(a.tch_rej_due_req_ch_a_if_crc- PI=Y,REO,PET
sum(ave_busy_tch / res_av_denom14)
(b.bsc_i_unsucc_a_int_circ_type+b.msc_controlled_in_ho+b.ho_un p_nbsc_res_avail >0
succ_a_int_circ_type))] parameter RXP,PMAX1
6 expansion
SD congestion
AVE_TCH_BUSY_HALF
SUM(AVE_BUSY_TCH/RES_AV_DENOM14)/ p_nbsc_res_avail 1, view the hardware alarm
(SUM(AVE_AVAIL_TCH_SUM/AVE_AVAIL_TCH_DEN) or SD available
+SUM(AVE_GPRS_CHANNELS_SUM/AVE_GPRS_CHANNELS_DEN)- p_nbsc_res_avail >0.1 2 IF cell is in border and
SUM(AVE_PERMANENT_GPRS_CH_SUM/AVE_PERMANENT_GPRS_ SDCCH for location updating
CH_DEN))
AVE_BUSY_GPRS_CH_DL/AVE_BUSY_GPRS_CH_DEN p_nbsc_packet_control_unit >0 ratio>50% then tuning HYS
2, the expansion of SD
sum(aver_tbfs_per_tsl_dl_sum) /sum(aver_tbfs_per_tsl_dl_den) * p_nbsc_packet_control_uni/ PDCH congestion
channel
100 该指标反映了网络下行软阻 <3 3,1 open
See whether
dynamicthe SD
塞的情况 hardware failure
sum(aver_tbfs_per_tsl_ul_sum) /sum(aver_tbfs_per_tsl_ul_den) * p_nbsc_packet_control_uni/ 4, open enhanced
2 burst traffic
dynamic
congestion,
100 该指标反映了网络上行软阻 <2 SD
塞的情况 observation
GPRS_TER_DG_DUE_INC_IN_CSW_TR P_NBSC_TRAFFIC 0
if(x>Default_GPRS_ 3 opening half rate and
decode(floor(cdef *gtchch / 100),0,1,floor(cdef * gtchch / 100)) tuning FRL,FRU
CAPACITY,Default_ 4 Retuning traffic balance
CDEF:c_bsc_bts.BTS_DGS_92
(AVE_GPRS_CHANNELS_SUM/ AVE_GPRS_CHANNELS_DEN)
gtchch:sum(decode(TRX_GPRS_ENA_TRX,1, P_NBSC_RES_AVAIL GPRS_CAPACITY= PI=Y,REO,PET
decode(floor(cded*gtchch / 100),0,1,floor(cded * gtchch / 100)) x,Default_GPRS_CA
CDED:c_bsc_bts.BTS_DGS_91 5 Reduce cell coverage use
PEAK_GPRS_CHANNELS
gtchch:sum(decode(TRX_GPRS_ENA_TRX,1, P_NBSC_RES_AVAIL PACITY) parameter GRXP,PMAX1
decode(ch.trx_ch_0_type,0,1,2,1,0) Counters from table(s): 6 Increace
decode(ch.trx_ch_3_type,0,1,2,1,0) a = c_bsc_bts CDED,CDEF,CMAX
Counters from table(s): 7 expansion
decode(ch.trx_ch_5_type,0,1,2,1,0) a = c_bsc_bts
decode(ch.trx_ch_7_type,0,1,2,1,0),0))
+From
+c_bsc_trx
NOT_AVAIL_TIME
From
c_bsc_trx
Counters from table(s): Inform the customer to
ERR_SEC
P_NBSC_ET_BSC check transmission
ERR_SEC_SEVER
TOPN Cell
0.50% 2.10%
Self-Check(Existing
NOTES
or not?)
Existing
Not Existing
Not Existing
Not Existing
Not Existing
Not Existing
Not Existing
Not Existing
Not Existing
Not Existing
Not Existing
Not Existing

he EGPRS downlink power control amplitude, the lower the interference effect is worse, but the corresponding impact on the perception of the data business is smaller. The rate
ting costs.
ring periods of low traffic, e.g. at night time. With dynamic power control of active dedicated channels, the feature reduces electricity consumption throughout the day.
a reduction in downlink interference caused by the BCCH frequency.
nd also helps in network planning.
which results in flexibility.
tion. In Flexi EDGE BTS, the operator saves around 40 W by powering down one dual TRX.
on of interference and hardware failure

antenna or reduce cell power. ZEUG:SEG=X,PMAX2=4;
mine the cell coverage distance

uency interference
he cell with repeater
uency
districtinterference
he
rxcell
levelwith repeater
ther external interference caused by the investigation of interference sources
district TA, whether overshooting
uency interference
rx level quality, determine the trx hardware issue or frequency issue
he cell with repeater
ther external interference caused by the investigation of interference sources
reflects the quality of the PDTCH channel, including the wireless environment of the network
rrier frequency interference, frequency issue or TRX may be a hardware problem

terference may be outside interference or repeater reason
he data business is smaller. The rate priority scheme is set to 29, and the power control scheme is set to 17, and the compromise scheme is set to 17.
mption throughout the day.

EDGE下行每TBF吞吐量 EDEG DL throughput per TBF

occurs on some top cells or EDGE下行每TBF吞吐量
the entire network.
Step1: Demarcation
write donw in D5 like the
demo

Alarm ID
7604
7606
7738
7767
Mandatory checking
7744
7745
7746
7725
8099
Except above, if other alarms

Step2:Checking
Feature Name
NACC
NCCR
EUTM
Smart resource adaptation
Extended Dynamic Allocation (EDA)
High Multislot Classes (HMC)
OSC Half Rate with SAIC MS
AMR Capacity
Dynamic PCU2 Pooling
Action 3.1: Identify low throughput causes
MCS-7、8、9 编码RLC块在EGPRS RLC块中所占的比例

Identify poor coverage or 下行电平质量分布
上行电平质量分布
上行弱覆盖比例
下行弱覆盖比例
TA分布
平均TA值
下行0~4级质量占比
(Cell Level) Interference Analysis上行0~4级质量占比
4~5级干扰比例
TRX 级下行RLC/MAC重传率
(TRX Level) Coverage and Interference Analysis
载频级4~5级干扰占比

TCH拥塞率
TCH话务量
TCH全速率话务
TCH半速率话务
每线话务量
数据业务等效话务量
Step3: Anylysis
下行PDCH复用度
上行PDCH复用度
TCH争夺PDCH次数
PDCH平均可用数
占用的PDCH的最大数目
动态PDCH配置时隙数
静态PDCH配置时隙数
上行GPRS拥塞使得TBF分配到EDGE时域
下行GPRS拥塞使得TBF分配到EDGE时域
GPRS降级因为语音负荷
下行MCS编码受限因为PCU资源
PCU拥塞率
EDAP拥塞率
GB 拥塞率

不可用时长
一般误码秒
严重误码秒

TCH配置信道数
TCH可用信道数
TCH可用率
全速率可用信道数
半速率可用信道数
链路平衡
+sum(ALLOC_2_TSL_DL)+sum(ALLOC_3_TSL_DL)
+sum(ALLOC_4_TSL_DL)+sum(ALLOC_5_TSL_DL)))
EDGE throughput per RTSL：
((((sum(DL_RLC_IN_ACK_MODE_MCS_1)+sum(DL_RLC_IN_UNACK_
MODE_MCS_1))*22)+
((sum(DL_RLC_IN_ACK_MODE_MCS_2)+sum(DL_RLC_IN_UNACK_
MODE_MCS_2))*28)+
Description
MODE_MCS_3))*37)+
KPI Name(English Name) Counter/Formula
MODE_MCS_4))*44)+
blems MODE_MCS_5))*56)+
MODE_MCS_6))*74)+
EDEG DL throughput per TBF MODE_MCS_7))*56)+
MODE_MCS_8))*68)+
MODE_MCS_9))*74))*8)/1000)
/
(((sum(DL_RLC_IN_ACK_MODE_MCS_1)+sum(DL_RLC_IN_ACK_MO
DE_MCS_2)+sum(DL_RLC_IN_ACK_MODE_MCS_3)+sum(DL_RLC_IN
_ACK_MODE_MCS_4)+sum(DL_RLC_IN_ACK_MODE_MCS_5)+sum(
DL_RLC_IN_ACK_MODE_MCS_6)+sum(DL_RLC_IN_UNACK_MODE_
MCS_1)+sum(DL_RLC_IN_UNACK_MODE_MCS_2)+sum(DL_RLC_IN
Alarm Name Influence(Major,Medium,Minor)
_UNACK_MODE_MCS_3)+sum(DL_RLC_IN_UNACK_MODE_MCS_4)
+sum(DL_RLC_IN_UNACK_MODE_MCS_5)+sum(DL_RLC_IN_UNACK
BTS OPERATION DEGRADED Medium
_MODE_MCS_6)+sum(RETRANS_RLC_DL_MCS_1)+sum(RETRANS_R
LC_DL_MCS_2)+sum(RETRANS_RLC_DL_MCS_3)+sum(RETRANS_RL
TRX FAULTY Medium
C_DL_MCS_4)+sum(RETRANS_RLC_DL_MCS_5)+sum(RETRANS_RLC
_DL_MCS_6))/50)+
BTS WITH NO TRANSACTIONS Major
((sum(DL_RLC_IN_ACK_MODE_MCS_7)+sum(DL_RLC_IN_ACK_MO
DE_MCS_8)+sum(DL_RLC_IN_ACK_MODE_MCS_9)+sum(DL_RLC_IN
BCCH MISSING Major
_UNACK_MODE_MCS_7)+sum(DL_RLC_IN_UNACK_MODE_MCS_8)
+sum(DL_RLC_IN_UNACK_MODE_MCS_9)+sum(RETRANS_RLC_DL_
EXCESSIVE TCH INTERFERENCE Major
MCS_7)+sum(RETRANS_RLC_DL_MCS_8)+sum(RETRANS_RLC_DL_
MCS_9))/100))
CHANNEL FAILURE RATE ABOVE DEFINED THRESHOLD Major
CH CONGESTION IN BTS ABOVE DEFINED THRESHOLD Major
TRAFFIC CHANNEL ACTIVATION FAILURE Major
RECEIVED BIT ERROR RATIO (BER) > 1E-3 Major
Feature's Meaning Adapted Scenario and Gain

network
The NACCcontrol
featurefunction of cell reselection,
is a prerequisite to achieveNCCR make thefunctionality.
the IB-NACC network more reduceresource
effective
There the cellallocation
reselection caused by data to stop the transmission time, increase th
Prevent MS GPRS access EDGE cell
= > make EDGE MS to get a better throughput Better throughput for EDGE MS
Make EDGE MS stay
TBF longer
Mode in the EDGE cell
Extended Uplink The'EUTM the
•Increases function canefficiency
network significantly as improve
less radiothe performance
resources of WAP to
are reserved forbrowse,
signalingdo
=With
> make EDGE MS totheget
ULaTBFs
better throughput
EUTM feature last EUTM
longer and it is less typical that an MS requests
•Makes features
a new
the UL TBFofvia
network high encoding
CCCH
more aaccounted
duringPhone
Smart data transfer
friendlyfor,session.
single
as slot throughput
Hence,
it allocates with EUTM
resources increased
featureon
based sig
thet
Smart Resource Adaptation" allocates only single timeslot (TSL) for new downlink •Increases
temporary theblock
number
flowof
(DLPS users
TBF) that can
by default, be simultaneously
if the size of the protocolaccommodated
data unit (PDU)ontoth
Extended Dynamic Allocation (EDA) is an extension to the Dynamic Allocation (DA) •Reduces
medium theaccess
TBF blocking
method. Itasenables
more PS userstocan
a mobile usebe accommodated
more on the same
uplink (UL) timeslots, and th
Prior to the version of R4'3GPP, up and down
'使GPRS/EDGE上行峰值速率达到236.8 kbit/sTSL and can not be more than 5 makePrior
the GPRS/EDGE uplink peak rate up to 236.8 kbit/s
to the version of R4'3GPP, up and down TSL and can not be more than 5
Release 3GPP 5 (TS 45.002) introduces the new terminal classes multislot, up •The feature
and down TSL is applicable
and up to 6 with existing GSM SAIC handsets, thus providing an imm
HMC enables the GPRS/EDGE downlink peak rate to reach 296 kbit/s Release
•It increases3GPP the5capacity
(TS 45.002) introduces
for voice the new
and releases terminalforclasses
capacity multislot,
data traffic up requ
without and
HMCincreased
•The enables the GPRS/EDGE
capacity per TRXdownlink
reduces peak rate toconsumption
the energy reach 296 kbit/s
per user. This re
Orthogonal subchannel (OSC) is a feature that increases the radio channel capa
•It avoids the need to add new sites, as it maintains the coverage area in capacity e
•Improvement in BSC PCU utilization factor. communication capabilities, to accele
The “Wideband AMR” (BSS20960) feature introduces wideband AMR coding asBy spproviding
•The increased
•Reduction
good voice
capacity quality
per TRX
in CAPEX investments.
and increased
effectively reduces site density through reduced c
•When another radio technology needs to share the same site, antennas or input po
Dynamic PCU2 Pooling” feature reallocates segments automatically between PCUs •Increase in revenue due to decreased PS call drops caused by a single PCU capac
•OPEX saving as radio network resource allocation is done automatically.
uses •More accurate PCU pool analysis in the PCU selection algorithm.
Sum over MCS 7-9(DL_RLC_Blocks_In_Ack_Mode+

MCS7~9 code rate UL_RLC_Blocks_In_Ack_Mode)/Sum over MCS 1-
9(DL_RLC_Blocks_In_Ack_Mode+ UL_RLC_Blocks_In_Ack_Mode)
s
DL LEV & QUAL Distribute KPI sum over a range (class_upper_range)
UL LEV & QUAL Distribute KPI sum over a range (class_upper_range)
eq_dl_qual4
UL Weak coverage rate 100*(SUM(freq_ul_qual0+freq_ul_qual1+freq_ul_qual2+freq_u
eq_ul_qual4
sum over all ranges
l_qual3+freq_ul_qual4+freq_ul_qual5+freq_ul_qual6+freq_ul_
DL Weak coverage rate 100*(SUM(freq_dl_qual0+freq_dl_qual1+freq_dl_qual2+freq_d
qual7)
sum Where
over all ranges
eq_dl_qual4
l_qual3+freq_dl_qual4+freq_dl_qual5+freq_dl_qual6+freq_dl_
CLASS_UPPER_RANGE<=15)/SUM(freq_ul_qual0+freq_ul_q
TA Distribution TA:class_upper_range
qual7) WHERE
eq_ul_qual4
TA=0
CLASS_UPPER_RANGE<=20)/SUM(freq_dl_qual0+freq_dl_q
TA=1
…….
l5+freq_dl_qual6+freq_dl_qual7)
TA=63
(freq_reports)/
sum over all ranges
(freq_reports)
Ave TA distance ave_ms_bs_dist
DL HQI KPI _qual3+freq_dl_qual4)/sum(freq_dl_qual0+freq_dl_qual1+freq
100*sum(freq_ul_qual0+freq_ul_qual1+freq_ul_qual2+freq_ul
UL HQI KPI _qual3+freq_ul_qual4)/sum(freq_ul_qual0+freq_ul_qual1+freq
_ul_qual2+freq_ul_qual3+freq_ul_qual4+freq_ul_qual5+freq_u
Interferences KPIs l_qual6+freq_ul_qual7)
100*Sum(Ave_Idle_f_Tch_4/Res_Av_Denom7+Ave_Idle_h_Tc
SUM(RETRANS_DL_RLC_MAC_BLOCKS)/SUM(DL_RLC_MAC_BLOCK
RLC/MAC Retransmission Rate on TRX sum(freq_ul_qual0+freq_ul_qual1+freq_ul_qual2
S)
+freq_ul_qual3+freq_ul_qual4+freq_ul_qual5)/sum(freq_ul_qu
TRX Quality al0+freq_ul_qual1+freq_ul_qual2+freq_ul_qual3+freq_ul_qual
CH_IF5+AVE_HALF_TCH_IF5）/
4+freq_ul_qual5+
TRX interference freq_ul_qual6+freq_ul_qual7)
4+AVE_FULL_TCH_IF5+AVE_HALF_TCH_IF5）
TCH Congestion ratio sum(a.tch_rej_due_req_ch_a_if_crc -
Average TCH traffic -sum(ave_busy_tch
sum(a.tch_rej_due_req_ch_a_if_crc-
/ res_av_denom14)
Average FTCH traffic succ_a_int_circ_type))]
AVE_TCH_BUSY_FULL
Average HTCH traffic SUM(AVE_BUSY_TCH/RES_AV_DENOM14)/
AVE_TCH_BUSY_HALF
AVE ERL PER CHANNEL +SUM(AVE_GPRS_CHANNELS_SUM/AVE_GPRS_CHANNELS_DEN)-
AVE PS traffic AVE_BUSY_GPRS_CH_DL/AVE_BUSY_GPRS_CH_DEN
CH_DEN))
sum(aver_tbfs_per_tsl_dl_sum) /sum(aver_tbfs_per_tsl_dl_den) *
AVERAGE DL TBFS PER TSL
100
AVERAGE UL TBFS PER TSL sum(aver_tbfs_per_tsl_ul_sum) /sum(aver_tbfs_per_tsl_ul_den) *
100
Number of GPRS territory downgrades made because of the increase in circuitdecode(floor(cdef *gtchch / 100),0,1,floor(cdef * gtchch / 100))
GPRS_TER_DG_DUE_INC_IN_CSW_TR
CDEF:c_bsc_bts.BTS_DGS_92
AVERAGE NUM OF PDCH decode(floor(cded*gtchch / 100),0,1,floor(cded
gtchch:sum(decode(TRX_GPRS_ENA_TRX,1,
(AVE_GPRS_CHANNELS_SUM/ * gtchch / 100))
AVE_GPRS_CHANNELS_DEN)
CDED:c_bsc_bts.BTS_DGS_91
The peak number of radio time slots delivered for GPRS use gtchch:sum(decode(TRX_GPRS_ENA_TRX,1,
+PEAK_GPRS_CHANNELS
Default_GPRS_CAPACITY + decode(ch.trx_ch_1_type,0,1,2,1,0)
DEDICATED_GPRS_CAPACITY + decode(ch.trx_ch_3_type,0,1,2,1,0)
The number of GPRS TBF allocations done in EGPRS territory because of congeul_gprs_tbf_in_egprs_terr
+From
The number of GPRS TBF allocations done in EGPRS territory because of congedl_gprs_tbf_in_egprs_terr
+c_bsc_trx
From
Number of GPRS territory downgrades made because of the increase in the circ gprs_ter_dg_due_inc_in_csw_tr
c_bsc_trx
Number of cases when MCS has been limited by the PCU (for example, DSP resdl_mcs_limited_by_pcu
PCU Congestion rate Sum(DL_MCS_LIMITED_BY_PCU)/Sum(DL_EDAP_ALLOCATION_REQU
EDAP Congestion rate sum(dl_tbfs_with_inadeq_edap_res-dl_msc_limited_by_pcu)/sum(dl
sum(8x(dlci_1_bytes_rec+dlci_2_bytes_rec+dlci_3_bytes_rec+dlci_
GB Congestion rate 4_bytes_rec+dlci_5_bytes_rec)/(period_duration x 60))/sum per
frbc over all unlocked child nsvc
(c_nsvc.committed_info_rate x 16)
Not available time NOT_AVAIL_TIME
Error second ERR_SEC
Serious error second ERR_SEC_SEVER

TCH CONFIGURATION CHANNEL ((AVE_AVAIL_TCH_SUM/AVE_AVAIL_TCH_DEN)+
EN)-
TCH AVALIBLE CHANNEL 100*[sum(ave_avail_TCH_sum/ave_avail_TCH_den+ave_GP
EN)-
GPRS_CH_DEN)
RS_channels_sum/ave_GPRS_channels_den)]/
TCH Availability KPIs [sum(ave_avail_TCH_sum/ave_avail_TCH_den+ave_GPRS_
(ave_bs_power - ave_dl_sig_str) - (ave_ms_power -
GPRS_CH_DEN)+AVE_NON_AVAIL_TCH_TIMESLOT)
channels_sum/ave_GPRS_channels_den+ave_non_avail_TC
ave_ul_sig_str)
Full rate available channel num AVE_GPRS_CHANNELS_DEN)-
H)] - 2*sum(ave_ms_power) / sum(power_denom1)
43
ave_ms_power,
Half rate available channel num AVE_TCH_AVAIL_HALF
43 - 2*sum(ave_bs_power) / sum(power_denom2)
LINK BALANCE ave_bs_power,
sum(ave_dl_sig_str) / sum(power_denom3) - 110
ave_dl_sig_str,
sum(ave_ul_sig_str) / sum(power_denom4) - 110
ave_ul_sig_str,
Tables Name Reference Value Instructions Operation Required Currnent Value
P_NBSC_PACKET_CONTROL_
UNIT >20
Judge EDEG DL throughput
per TBF reason: TOPN cell or
Whole network
action2
Meaning Instructions
0 check antenna
0 Fault: the replacement of TRX
0 No business warning: restart

0 information
0 Interference alarm: find the interference
0 TRX
0 expansion channel
0 GENA or PCU to solve the switching
0 Notification transfer view fault
p the transmission time, increase the rate
performance
esources of WAP to
are reserved forbrowse, download
signaling and download small files FTP
type of traffic.
single
as slot throughput
it allocates increased
resources based onsignificantly
the need rather than based on handset's multislot capability.
imultaneously accommodated on the radio resources.
an be accommodated on the same radio resource.
SL and can not
C handsets, beproviding
thus more thanan5 immediate gain with just a software upgrade in the GSM radio network.
w terminalforclasses
capacity multislot,
data traffic up requiring
without and downnew TSLTRXs
and up
or to 6
related hardware. This reduces the number of TRXs required to realize a specific capacity or spectral efficiency.
ate
ergytoconsumption
reach 296 kbit/s
per user. This reduces the energy consumption required per Erlang significantly.
ins the coverage area in capacity extensions.
ommunication
uces capabilities,
site density to accelerate
through reduced the return
combining of investment in GSM network, no need to replace the existing equipment or any hardware
losses.
the same site, antennas or input ports of combiners may be released by the introduction of OSC Half Rate with SAIC MS.
rops caused by a single PCU capacity limitation.
on is done automatically.
election algorithm.
1、capacity issue
2、raido Enviroment
p_nbsc_coding_scheme >60% issue
3、parameter issue
Counters from table(s): level [-80,-47]:qual Weak coverage :check cell

Investigation
transmit of interference
power, adjust the and hardware failure
p_nbsc_rx_statistics [6~7] proportion<5%
Counters from table(s): level [-110,-90]:qual high gain antenna, add the
p_nbsc_rx_statistics [6~7] proportion<5% check
pull far cell
cell transmit
P_NBSC_RX_STATISTIC <3% power,
,add newadjust
station the
S antenna, replaced by
P_NBSC_RX_STATISTIC <3% the high gain antenna,
S add the pull far cell
Counters from table(s): TA>5 ,add new station
p_nbsc_timing_advance proportion<20%
urban: 0~2
p_nbsc_timing_advance Help to determine the cell coverage distance
surban:2~4 1 Check frequency interference
Counters from table(s): 2, whether the cell with repeater
>94% 1
3,Check
check frequency
p_nbsc_rx_qual 2,
Counters from table(s): 4, whether
check thethe trxcell with
level repeater
>94% 3, Check whether external interference caused by the investigation of interference sources
p_nbsc_rx_qual 4, check the district TA, whether overshooting
Counters from table(s): 1
5,Check
check frequency
the trx levelinterference
<5%
p_nbsc_res_avail 12,frequency
whether theproblem,
cell with repeater
P_NBSC_RLC_BLOCKS_PER_T 3, Checkthe
change whether external interference caused by the investigation of interference sources
frequency
<5%
RX 12 frequency
TRX TCH
problem,
congestionchange
problem,
TRX 1 See
change thewhether
frequency the
p_nbsc_rx_qual >95% hardware failurechange
or TCH
2 TRX problem,
p_nbsc_underlay <5% 1 singleavailability
TRX carrier frequency interference, frequency issue or TRX may be a hardware problem
2 2allburst
carriertraffic congestion,
interference may be outside interference or repeater reason
observation
Counters from table(s): tuning FRL,FRU
a = p_nbsc_traffic <2% 4 Retuning traffic balance
b = p_nbsc_ho PI=Y,REO,PET
p_nbsc_res_avail >0 5 Reduce cell coverage use
p_nbsc_res_avail parameter RXP,PMAX1
6 expansion
p_nbsc_res_avail SD congestion
p_nbsc_res_avail >0.1 or SD available
p_nbsc_packet_control_unit >0 SDCCH for location updating
p_nbsc_packet_control_uni <3 2, the expansion of SD
channel
p_nbsc_packet_control_uni <2 3,PDCH
opencongestion
dynamic SD
1 See
4, open whetherdynamic
enhanced the
P_NBSC_TRAFFIC if(x>Default_GPRS_
0 hardwareSD failure
CAPACITY,Default_ 2 burst traffic congestion,
P_NBSC_RES_AVAIL GPRS_CAPACITY= observation
x,Default_GPRS_CA 3 opening half rate and
P_NBSC_RES_AVAIL PACITY) tuning FRL,FRU
a = c_bsc_bts 4 Retuning traffic balance
b=c_bsc_trx PI=Y,REO,PET
a = c_bsc_bts 5 Reduce cell coverage use
b=c_bsc_trx parameter GRXP,PMAX1
0 6 Increace
CDED,CDEF,CMAX
0 7 expansion
P_NBSC_TRAFFIC 0
P_NBSC_DYNAMIC_ABIS 0
p_nbsc_dynamic_abis <5% Retuning PCU
p_nbsc_dynamic_abis <3% ADD EDAP Capacity
p_nbsc_frame_relay <2% ADD GB Capacity
Counters from table(s): Inform the customer to

P_NBSC_ET_BSC check transmission
P_NBSC_RES_AVAIL
P_NBSC_RES_AVAIL ’=TCH CONFIGURATION CHANNEL
>99%
p_nbsc_res_avail
p_nbsc_res_avail
On behalf of the hardwar
p_nbsc_res_avail
<10
p_nbsc_power
Written Item by the FL
Self-Check NOTES
TOPN Cell
Self-Check(Existing
NOTES
or not?)
Existing
Not Existing
Not Existing
Not Existing
Not Existing
Not Existing
Not Existing
Not Existing
Not Existing
Not Existing
Not Existing
Not Existing
fic capacity or spectral efficiency.

erference sources
ncy issue
erference sources
TRX may be a hardware problem

返回 Back
参数(特性的参数单独列出)Parameters（Excluding Features Paramters which will be listed specially）
值域范围建议值
参数名称参数含义 ABBREV Value Recommendation
Paramter Name Paramter's Meaning Range Value
maxNumberRetransmission The maximum number of retransmisRET (1,2,4,7) 4

numberOfSlotsSpreadTrans The number of TDMA frames over whi SLO (3..12, 1 12
penaltyTime OPTIONAL (C2 Cell reselection parame PET (20…640) 20
temporaryOffset OPTIONAL (C2 Cell reselection parame TEO (0…70 step 10)dB
cellReselectParamInd OPTIONAL (C2 Cell Reselection para PI (Y/N) Y
cellBarQualify OPTIONAL (C2 Cell reselection param QUA (Y/N) N
cellBarred The parameter indicates if MSs are notBAR allowed(Y/N) N yes,ms will not camp on
to access the cell.if
cellReselectOffset OPTIONAL (C2 Cell Reselection parame REO (0…126 s 0
cellReselectHysteresis The received RF power level for required (0…14,st The parameter
HYS cell re-selection. 10 belongs to the cell
drInUse OPTIONAL (Directed Retry)DirectedDR R (Y/N) Y
drmethod it's the switch type of para with 0 w DRM (0~1) 1
drThreshold The parameter defines the thresholdDRT va (-100~-47 -80
radioLinkTimeout 无线链路超时/radioLinkTimeout RLT (4…64,st 32
powerCtrlEnabled 是否开启功率控制/power Ctrl Enabled PENA (Y/N) Y
PLMN permitted A list of PLMNs for which the MS is PLMN (0…7)
enaFastAveHo The parameter indicates whether th EFH (Y/N) Y
enableIntraHoInterUL The parameter indicates whether anEIC (Y/N)
Y for non-hopping, N for BB
enableIntraHoInterDL The parameter indicates whether anEIH (Y/N)
Y for non-hopping, N for BB
enablePwrBudgetHandover The parameter indicates whether th EPB (Y/N) Y
hoPeriodPBGT The parameter contains the interva HPP (0…63)SA 6
btsLoadThreshold The parameter is used for the handov BTL (0…100)% 80
hoPriorityLevel The parameter defines the priority levPRI (0…7) 3
hoLoadFactor The parameter indicates how much th OF (0…7) 1
rxLevMinCell Minimum signal level measured by the SL (-110…-4 -98
EGPRS Init MCS Ack Mode With this parameter you indicate t MCA (1…9) 7
EGPRS Init MCS Un Ack Mode With this parameter you indicate t MCU (1…9) 6
The parameter describes the binary A r LPHA (0…10)
7 (GSM 900)
alpha
8 (GSM1800)
34 (GSM 900)
gamma The parameter controls the signal strGAMMA (0…62)
36 (GSM1800)
defaultGPRScapacity The parameter determines the amount CDEF (1…100%) 50
24
16
12
9
8
7
6
5
5
4
4
dedicatedGPRScapacity The parameter determines the amount CDED (0…100%) 1
gprsEnabled The parameter defines whether the GP GENA (Y/N) Y
EGPRSEnabled EGPRS Enabled EGENA (Y/N) Y
maxGPRScapacity With this parameter you define the CMAX
2 Traffic channel is allocated primarily beyond (0…100%) 100
trxPriorityInTCHAlloc the BCCH TRX TRP (0…2) 0
preferBCCHFreqGPRS The parameter defines whether the BC BFG (Y/N) N
1... EGPRS link adaptation is enabled for RLC acknowledged mode
EGPRS Link Adaptation Enabl 2... EGPRS link adaptation is enabled ELA for both (0,1,2)
RLC acknowledged 2 and RLC unacknowledge
mean BEP offset 8PSK With this parameter you can adjust MBP (-31…31) 0
GPRSenabledTRX The parameter defines whether the GGTRX Y/N Y
msTxPwrMax *GSM*dBm The parameter defines the maximumPMAX1 p (5…43 st 33
msTxPwrMax *DCS*dBm The parameter defines the maximumPMAX2 p (0…36 st 30
minMSTxPower *GSM*dBm The parameter defines the minimum PMIN
p (5…43 st 5
minMSTxPower *DCS*dBm The parameter defines the minimumPMIN p (0…36 st 0
rxLevAccessMin The parameter defines the minimumRXP l (-110…-4 -102~-98
msTxPwrMaxCCH *GSM*dBm The parameter indicates the maximuTXP1 (5…43 st 33
msTxPwrMaxCCH *DCS*dBm The parameter indicates the maximuTXP2 (0…30 st 30
bsTxPwrMax *GSM*dBm The attenuation from the (preattenu PMAX1 (0…30 st 0
bsTxPwrMax *DCS*dBm The attenuation from the (preattenu PMAX2 (0…30 st 0
bsTxPwrMin The attenuation from the (preattenu PMIN (0…30 st 20
callReestablishmentAllowed The parameter indicates if call re-estRE (Y/N) Y
enablePwrBudgetHandover The parameter indicates whether th EPB (Y/N) Y
pcLowerThresholdsQualDL The parameters compare the averaged LDR (0…7) 3
nx(1…32) Nx: The total number of averages tha LDN 3
px(1…32) Px: Number of averages that have toLDP 2
pcLowerThresholdsQualUL The parameters compare the averagedLUR (0…7) 3
nx(1…32) Nx: The total number of averages tha LUN 3
px(1…32) Px: Number of averages that have toLUP 2
pcUpperThresholdsQualDL The parameters compare the averagedUDR (0…7) 0
nx(1…32) Nx: The total number of averages tha UDN 5
px(1…32) Px: Number of averages that have toUDP 4
pcUpperThresholdsQualUL The parameters compare the averaged UUR (0…7) 0
nx(1…32) Nx: The total number of averages tha UUN 5
px(1…32) Px: Number of averages that have toUUP 4
pcLowerThresholdsLevDL The parameters compare the averaged LDR (-110…-47)DBM-75
nx(1…32) Nx: The total number of averages tha LDN 1
px(1…32) Px: Number of averages that have toLDP 1
pcLowerThresholdsLevUL The parameters compare the averaged LUR (-110…-47)DBM-91
nx(1…32) Nx: The total number of averages tha LUN 1
px(1…32) Px: Number of averages that have toLUP 1
pcUpperThresholdsLevDL The parameters compare the averaged UDR (-110…-47)DBM-65
nx(1…32) Nx: The total number of averages tha UDN 4
px(1…32) Px: Number of averages that have toUDP 3
pcUpperThresholdsLevUL The parameters compare the averaged UUR (-110…-47)DBM-78
nx(1…32) Nx: The total number of averages tha UUN 3
px(1…32) Px: Number of averages that have toUUP 2
optimumRxLevUL The parameter indicates the optimum LEV (-109…-47)(dbm) -80
UL dtxMode The parameter identifies the mode f DTX (0(MS may 1
msMaxDistanceInCallSetup The parameter defines the maximumDMAX d (0,,,255) 255
syncronised The
Withparameter indicates
this parameter if the adjace
you define SYNC sequence
the training (Y/N) Same BCF set Y
TSC code (TSC) of a carrier TSC (0…7)
Must equal BCC OF The cell
bcchFrequency bcchFrequency FREQ Must equal with BTS setting
adjacentCellIdLac adjacentCellIdLac LAC 1...65533
Must equal with BTS setting
adjCellBsicNcc adjCellBsicNcc NCC (0…7)
Must equal with BTS setting
adjCellBsicBcc adjCellBsicBcc BCC
an MS has to receive before it is allowed to access (0…7)
Must
the equal with BTS setting
gprsRxlevAccessMin cell. GRXP (-110...-47) -98
gprsDlPcEnabled DLPC (Y/N) Y
PCWC
0...10 dB, step 2
dlpcwindowsize dBm 8
PCPOW
0...10 dB, step43
dlpcpowerreduction
dBm
dlpc8pskbeptarget PCPSK 0...31, s 17
dlpccitarget PCCI 0...30 dB 12
With this parameter you indicate the maximum block
egprsMaxBlerAckMode error this
With rateparameter
of first transmission
you indicate in acknowledged
theBLA
maximum block mode.
10-100% 90
egprsMaxBlerUnAckMode error rate in unacknowledged mode. BLU
With this parameter you can adjust the MCS and modulation 1-100 10
egprsMeanBepOffsetGmsk preferences With this parameter you can adjust the MCS and MBG -31..31 0
egprsMeanBepOffset8psk modulation
With preferences
this parameter you define how the MBP -31..31is
GPRS territory 0
gprsTerritoryCalc seen when calculating FR resources CTC
With this parameter you set the time which must elapse 1,2,0 0
#N/A between two subsequent territory updates
GTUGT
With this parameter you define the maximum number of 1-255 5
pcuMaxNoDLtbfInCH TBFsthis
With thatparameter
a radio time youslot can the
define havemaximum
MNDL
in average number1..9of 9
pcuMaxNoULtbfInCH TBFs that a radio time slot can have MNUL
in
availability for circuit switched services in a BTSaverage, 1..7 7
freeTSLsCsDowngrade with GPRS territory. CSD 0-100% 95
freeTSLsCsUpgrade With this parameter you define a pe CSU 0-10
Full rate TCHs are allocated until the number of free full rate resources 4 is reduced below the
btsSpLoadDepTchRateUpper Full rate TCHs are allocated when the FRL (0..100)% 0
number of free full rate resources increases above th
btsSpLoadDepTchRateLower TCH resources that must be available FRUfor traffic(0..100)%
channel 100
amrSegLoadDepTchRateLoweallocation in order to use full rate for AFRL AMR calls(0..100)%
in the cell 40
amrSegLoadDepTchRateUppe With this parameter you define the
The optimization procedure works only for intra-BSC handovers. pe
AFRU (0..100)% 60
msPwrOptLev POPT (-110…-47,N) dbm -80
BS_CV_MAX 0-15 9~11
The parameter
tAvgW controls the signal strength filter period for power control IFPin the packet
(0…25)idle mode.9
The parametertAvgTcontrols the signal strength filter period for power controlTFP in the packet
(0…25)transfer mode.
13
With this
bit error
parameter
probability
you define
filter averaging
the bit error
period
probability filter averaging period for EGPRS (1,2,3,4,5,7,10,12,15,20,25)
BEP channel quality measurements.
10
The parameter
GPRSenabledTRX
Thedefines whether
limit value the that
for r_dif GPRS capability
triggers is control
a flow enabledmessage
or disabled
GTRX for the
(Y/N)
(r_dif>0.1). current TRX.Y
FC_R_DIF_TRG_LIMIT (/10)% 0-1000 100
FC_MS_R_DEF_EGPRS (Bytes/s) MS-specific leak rate default value
Minimum value of MS leak rate for EGPRS 1000-20000 15000
FC_MS_R_MIN Buffering capacity default value 20-200 40
FC_MS_B_MAX_DEF_EGPRS (Bytes) 2000-20000 25000
FC_R_TSL_EGPRS (Bytes/s) EGPRS timeslot transmission capacity 1000-8000 4500
g capacityFC_B_MAX_TSL_EGPRS
of one EGPRS timeslot. This (Bytes)
parameter is used instead of fc_b_max_tsl, if the5000-65280 segment has EGPRS 25000capability. (25 Kb
be listed specially）
调大的影调小的影
网元 MO归属适用版本响响重要程度应用场景
Network MO Version Influence Influence Important Applicati MML
Element Belonged Adapted When When on
degree scenarios Commond
Increased Decreased
SEG Suitable for Suitable for traffic intensive area EQM

SEG When the num In the case of less RACH conflict, t EQM
SEG Specifies th Specifies the time that TEO has a ro EQM
SEG Defined in t Defined in the time of PET, the temp EQM
SEG EQM
SEG EQM
SEG EQF
SEG IDLE state i Reduce traffic to enter MS enter /pr EQM
SEG Under the coThe boundary of the location area red EQG
SEG EQF
SEG EQF
SEG Difficult to Easy to become a candidate cell, but EAM
SEG reduce dropAdded drop Highc ZEQM
SEG Open to reduce networkHigh ZEUG
SEG High ZEQF
SEG Medium ZEHG
SEG Medium ZEHG
SEG Medium ZEHG
SEG High ZEHG
SEG Slow PBGT Fast PBGT Medium ZEHG
SEG Allow more trReduce traffiMedium ZEQM
SEG The adjacentAdjacent area Medium ZEAM
SEG Priority dowPriority to Medium ZEAM
SEG Cut into the The cut is e Medium ZEAM
SEG But for the "But for the High ZEQV
SEG "To improve"Reduce the rate, can guarantee the ZEQV
SEG The greater The smaller the ALPHA, the smaller t ZEUO
SEG The larger t The smaller the GAMMA value, the g ZEUO
SEG Increase theReducing the dynamic PDCH, will in ZEQV
SEG
SEG
SEG
SEG
SEG
SEG
SEG
SEG
SEG
SEG
SEG
SEG Increase theReduced static PDCH, will increase a ZEQV
SEG ZEQV
SEG ZEQV
SEG Increase theReduced dynamic PDCH, will increas ZEQV
SEG According to the actual situation of the distri ZEQM
SEG The GPRS channel is given priority in the use o ZEQV
SEG Link adaptation EQV
SEG Reduce the high encoding ratio, incre EQV
Can increase
SEG ERM
SEG Increase th Reduced cell phone (900M) transmi ZEQM
SEG Increase th Reduced cell phone (1800M) transm ZEQM
SEG Increase th Reduced cell phone (900M) transmi ZEQM
SEG Increase th Reduced cell phone (1800M) transm ZEQM
SEG Reduce cove Increase coverage, reduce service q ZEQG
SEG When the mobWhen the mobile phone is connected ZEQG
SEG When the mobWhen the mobile phone is connected ZEQG
SEG Reduce the Increase the 900M cell emission po ZEUG
SEG Reduce the Increase the 1800M cell emission p ZEUG
SEG Cell can redCell can be reduced power range ZEUG
SEG Open can reduce the words
SEG Open can reduce network interference
SEG Reducing the probability of downlink power and reducing the
SEG Increased power rise time
SEG Reducing the uplink power probability and reducing the netw
SEG Increase the downlink power probability, reduce network int
SEG Increased power down time
SEG Increase the uplink power down probability, reduce network
SEG Increase the probability of downlink power, increase network
SEG Increase the uplink power probability, increase network inte
SEG Reducing the downlink power probability and increasing the
SEG Reduce the uplink power probability, and increase the netwo
TRX Uplink optimization level, think this value will not cause upli
SEG Open can reduce uplink interference
SEG Setting errors can cause the network to be unable to access
ADJ Setting the error will cause the switch to fail
TRX Set the error causes the switch failure and crosstalk
SEG Reduce cove Increase coverage, reduce service quality
SEG Reduce downlink interference ZEQO
This parameter defines the PS downlink power control relative to full power emission ma
POC This paramet ZEUO
POC After the TBAfter the TBF is established, the ini ZEUO
The greater This
the value,
value the
is about
lowersmall,
the EGPRS
EGPRSdownlink
downlinkpower
powercontrol
controlamplitude,
amplitudethe
is about
lower deep,
the interfer
the in
BSC The greater the value, the GPRS downlink power ZEEOcontrol is about shallow, lower interference effect is
This value is about small, GPRS downlink power control amplitude is about deep, the int
BSC ZEEO
The maximum block error rate of the first transmission is used in the verification mode, which is used
SEG ZEQV
The maximum block error rate of data transfer is used in the non verification mode, which is used for
SEG ZEQV
GMSK coding compensation, the use of the parameters can be adjusted MCS and modulation param
SEG The smaller the value, the lower t ZEQV
SEG Increased MReduced MBP will make mobile pho ZEQV
BSC 0: neutral, 1: data first, 2: voice priority ZEEM
BSC Too large ca If the parameter setting ZEEN
BSC In order to avoid the TBF congestion, the value i ZEEM
BSC In order to avoid the uplink TBF congestion, the ZEEM
BSC Reduce the I dncrease the probability o ZEEM
BSC Increase theBy reducing the value of CSU can be ZEEM
SEG The higher thThe lower the value, the lower the pro ZEQM
SEG The greater The
t smaller the value, the greater the ZEQM
SEG After AMR actThe lower the value, the lower the pro ZEQM
SEG After AMR actThe smaller the value, the greater the ZEQM
ADJ Will increas The uplink transmission power of the ZEAM
BSC ZEGO
POC ZEUM
POC ZEUM
POC ZEUM
TRX ZERM
BSC ZWOI
BSC ZWOI
BSC ZWOI
BSC ZWOI
BSC ZWOI
BSC ZWOI
返回 Back
特性名称特性的含义该特性的参数名称

Feature Name network control function
Feature's of cell
Meaning Feature Parameter Name
reselection, NCCR make the network
more effective resource allocation
AMR Capacity The “Wideband AMR” (BSS20960) featur AMR
Prevent MS GPRS access EDGE cell
(E)GPRS DL Power Control =
The> make EDGEDownlink
(E)GPRS MS to get(DL)
a better
Power Control feature helps in controlling the downlin
throughput
Increased Dynamic SDCCH Capacity It is increased
Make EDGE MS to stay
a maximum
longer in of
the24 channels in BCCH TRXs and to a maximu
NACC EDGE cell
The NACC feature is a prerequisite to achieve the IB-NACC functionality. Ther
= > make EDGE MS to get a better
NCCR throughput
Extended Uplink TBF Mode PRFILE：046：0071 UL_TBF_REL_DELAY
EUTM With EUTM feature the UL TBFs last longer PRFILE
and046:0072
it is less UL_TBF_SCHED_RATE_
typical that an MS reques
Smart Resource Adaptation Smart Resource Adaptation" allocates only single timeslot (TSL) for new downlink tempora
GPRS CS3 and CS4 Compared to the current network support CS2 encoding, CS4 encoding a single ch
Adjustable TBF Multiplexing Density operator controls upgrades/downgrades of the (E)GPRS territory at the cell level by
Wideband AMR Wideband AMR is adopted by both 3GPP and ITU-T. Therefore, the same codec ca
Separate UL&DL AMR Link Adaption Thindependent UL/DL AMR link threshold can make a certain wireless condition to ob
AMR HO Signalling Optimization
AMR Progressive Power Control AMR Progressive Power Control (PPC) provides a mechanism to change the RXQU
Low-rate AMR FR codecs provide
AMR Unpacking Optimization satisfactory
This speech quality
feature provides new AMR in radio
quality and level based handover parameters to av
channels whose carrier-to-
Adjustable UL RLT Increase Step This feature allows
interference the operator
ratio (C/I) is up to 4todB
adjust the size of a single increase step from the
worse than that needed to give
FACCH and SACCH repetition
reliable operation of the FACCH and
FACCH repetition for AMR FR SACCH control channels. This
results in calls being dropped even
FACCH repetition for AMR HR though their speech quality is still
FACCH Power Increment acceptable.
The effective C/I for downlink FACCH
AMR Signalling Measurement and uplink/downlink SACCH can be
improved by increasing the base
OSC Half Rate with SAIC MS Orthogonal subchannel (OSC) is a feature that increases the radio channel capacit
station (BTS) Tx power for FACCH,
or by repeating the FACCH/SACCH
Multipoint Gb Multipoint Gb feature
block allows single PCU2 to connect with several SGSNs
Dynamic PCU2 Pooling Dynamic PCU2 Pooling” feature reallocates segments automatically between PCUs
Extended Cell for Data through this function to achieve the expansion of residential data services
Packet Abis over IP/Ethernet enables a bandwidth optimized connectivity to packet switched networks. Bandwidt
Energy Saving mode for BCCH TRX In the "Energy saving mode for BCCH TRX" feature, the BTS transmits at a 2 dB lo
Double Power TRX for 2G BTS (BSS20870), is a licence based application softwar
Double Power TRX for 2G BTS Extended BCCH” feature allows the reduction of the number of SI2 quarter messag
When this feature is in use, it reduces the amount of SI2 quarter messages that are
Extended BCCH
Extended CCCH Extended CCCH" feature increases the CCCH channel capacity in the cell. It may b
Intelligent Selective Paging Precise Paging feature enhances the signaling capacity on the Common Control Ch
With the introduction of the feature "Paging coordination in BSC", the BSC performs
Paging coordination in BSC '在PS数据业务期间，用户也可以收到CS寻呼
A5/3 Ciphering For CS calls and SMSs, the A5/3 ciphering code provides more secure air interface
Flexible MCPA TX Power Pooling The Flexi Multiradio BTS RF Module (FXxx) has three branches which are equipped
Dynamic Frequency and Channel Allocation
Prior(DFCA)
to theDynamic
version of R4'3GPP, up and down TSL and canDynamic
not be more than 5(DA)
Extended Allocation (EDA) is an extension to the Allocation
Extended Dynamic Allocation (EDA) Release 3GPP 5 (TS 45.002)
'使GPRS/EDGE上行峰值速率达到236.8 kbit/s introduces the new terminal classes multislot, up and
HMC enables the GPRS/EDGE downlink peak rate to reach 296 kbit/s
High Multislot Classes (HMC)
STIRC STIRC is designed to cancel uplink interference and also to provide improved link b
Adjustable Intelligent Shutdown 2G BTS
2G TRX Automatic Power Down 2G automatic power down" feature introduces an energy saving mechanism for Fle
PCU2 Basic SW per 256 ch (Abis 16kbit/s)
Selective
BCCH
8 Note:
(ZW7I)
mode
BCCH Define
produces
AMR HR:ifTRXs.
set
TRX BSCis FR
001253
HR
Increased
FTP ordownload
number>,NRIB
ZW7I:FEA,FUL AMR TCH
Paging
ZERM:BTS=<B
message
ZW7I:LIC,FULL
defined
Lock
parameter
background
ZEQY:BTS=<B the to
for ON.
buffer
BCCH the
the
SEIZURES
is 'ON'
Dynamic
operation
=<network
L:FEA=3476; (W7I). via
ZW7M:FWA=13
TS
is
TRX already
:LIC=<licence
BTS
neighbor
interference
TS in
with MML
FOR
AMR
SDCCH
the
resource MS
ZW7M:FEA=34 WB-AMR.
HR:
01:ON;
identification>,T
reserved,
code>;
question.
command you
amount
matrix
identification>:
For more
ZW7I:FEA,FUL
Capacity
13.Stop
identifier
76:ON;
3 Test
RX=<TRX
have to
(BIM)
the inERS.
weight,
the
free itto
3 Activate
Reconfigure
ERS:BTS=<bts
MS
tables
HRC=<AMR amount
information
L:FEA=1;
feature
PCU based
state theon on
binary>,PRE=<i
This
feature. function
identification>:P
by giving UseZOEQ the
IB-NACC
them
HR
checking
AMR
ON to
_id>,TRX=<trx_
weight
those codec andsuitable
reports.
FR:
(W7M).
measurement the PS
dentify
involves
GSM
REF=P;
command the and
network
特性参数特性参数 feature
values
id>:L;
traffic
At
mode least
measurement
ZW7I:FEA,FUL
ZW7M:FEA=10
(TPE) ifin
load
set>; 1000 BSC
含义值域范围推荐值网元 configuration
parameter
message
try to reserve it
MO归属适用版本 After (ZW7M)
needed
6 Configure
weight
measurement
The
data,
L:FEA=72
77:ON; see the
value
the forwith 0 the
Feature default：
Feature Recommend type>:RIP=<re
modification
analyzer
again by to the
ZW7M:FEA=66:
ZEEM
BCCH
PCU
samples
means
◦Reporter
2、Check /
TRX ZEQM.
selection
thatper and
thatby
Parameter ation Network
Parameter 2000D（2 MO Version mote
4 MML
Check
measurement
process
check IPCommond
paging that
Element Belonged Adapted ---------------------
ZOEBR.
ON;
3 Activate
modifying
algorithm
neighboring
whole
Performance
the
period
1 licence
feature
Extended
address>,RPN codec
both ifDHR cell
the
's s）'Value Value ⑴
from Close
Abis
---------------------
3.Define
4 Check GENA
the
if the
Meaning Range multiplexing
Extended
needed.
are
mode needed
Management
covering
state
counters,
BCCH
BR=<remote set
change
feature is
AMR in
for
Range： ZEQV:SEG=**:
interfaces.
ZW7M:FEA=3460:ON;
---------------------
monitoring
feature is been
OFF ON BTS the
CCCH
an
disabled.BTS
ZEEQ:NAPSA=
estimation
Principles
PPC
succeeded
SMART
licence
UDP has
port channel
is in
300D- GENA=N:::TBF
1.Create
ZEQV:SEG=<SEG
-----------------
criteria
successfully (ZOEC) ID>:DLPC=Y
Modify
type
<neighbour
and
NetAct
installed
(W7I).
PHONE
installed
number>,:;thethe Product
(W7I).
1using Limit
TSL
ps in controlling the downlink
3000D transmit power on (E)GPRS timeslots and T=**,TBFU=**,T
adjacencies.
decrea
ZOEC::SR:
activated
for
Modify
amount
creationTriggering
Documentation
ZW7I:LIC,FULL
ZW7I:FEA,FUL
DL
the
Repeat TBF
command theweight
of a
this
default： BFD=**;
BTS1,
9 Unlock
((OFAM=14E)O
(ZW7I) BTS2 the
RXs and to a maximu OFF ON BSC OSC
Extended
for PCU
neighbor-cell
◦Converting
:LIC=<licence
L:FEA=1077;
ESTABLISHED
W7I.
step DHR
with aare
4（80ms NACC on the final download rate basically ⑵
and
TRX
can Open
BTS3
R(CFAM=14E))
ZW7I:FEA,FUL(ERS)
not see or
a significant upgrade. Therefore for the use of
Multiplexing
CCCH
selection
specific
BSC
code>;
and SMART
ZW7I:LIC,FULL
different channel
BIM
NSE
ACC functionality. TherOFF ，4个RLC NACC 对最终的下载速率基本看不出明显提升。因此对于NACC
BSC GENA：
adjacent,
;BTS
L:FEA=66; (EQS). while 的使用，由于其作用有限，建议谨慎考
parameter
type
table
3、Check
PHONE (‘CCCHE’
algorithm>,MAP
Measurement entry.
:LIC=<licence
value ifhas 1 TSL
more theThe
块调度一 ZEQV:SEG=**:
BTS4
ZERS:BTS=<B
Conditions noare:
(DHRLIM)
in
and
value
1
DL MML)
SA=<MS
BIM Check
code>:;
SGSN update
TBF of the to to a
次） ZEEM:NCM=Y;
GENA=Y;
adjacencies.
TS
ZOEC:<COMP
value
radio
amount
period
Observation
AMR
whether
REALLOCATE
2 Check
connections time
less
PPC can weight
the
the slot
than
beare
071 UL_TBF_REL_DELAY_EXT Range： 1000 ⑶ Query
2.Turn
identification>,T
>:SR: the MS
or
2,
for
Result4,
equal
printed
feature
license
D
valueTO
needed.PCU and/or
Files
NORMAL to
using
states
isThe
ofconnect the
6 in
2 UL_TBF_SCHED_RATE_EXT 2~50 4 parameter：
on
RX=<TRXand
((((OFAM=14E)
lower
with
(W7I). BCCH
selection
the
installed
TBF limit
following
MEFICO
will be in TRX
the
itExtended
maximum
ZEQO:SEG=**:
to BTS1.
identification>:
OR(CFAM=14E
criterion
with MML
algorithm>,PTL
command. for
6.Stop
Downlink
BSC
updated.
BCCH
SL) for new downlink temporary block flow (DL TBF) by default, if the size of the protocol
number
GPRS data the
feature
of AMR(PDU) to be transferred does not exceed the thre
unit
Remove
U;
))AND((NUM=0
AMR
command
PSA=<PS
ZEEO HR :DFCA; the
measurement
PPC:
ZW7I:LIC,FULL
state
SGSN with thethe
g, CS4 encoding a single channel rate of 60% battery
ZEQS:BTS=<B
D332)AND(DA
packing.
ERM.
traffic
Note: load To fromThe
(TPE).
ZW7I:FEA,FUL
:LIC=<license
command
connections W7I.
MS.
TS
TB29=55))))
other
Time
weight
ensure slot
OSC for
the 2PCU
ZTPE
S territory at the cell level by modifying cell level parameters. This facilitates L:FEA=578;
code>;
ZW7I:FEA,FUL
from one PCU
3.Make
identification>:
D332:
DHR
must
selection
correct be 29 MT must CS
:MEASUR,TRA
Uplink
2 Activate
L:FEA=1858;
is eight. AMR the
call.
U;
be 55(CIPHER
parameters
configured
algorithm>; ofas can
herefore, the same codec can be applied for wireless and wireline services. Woperation FFIC;
PPC:
feature
3
4 Turn
Set the in
the the
CS
MODE
be
CCCHE
9 call
left
Define
DFCA, at isbefore
you their
BSC
ain wireless condition to obtain more effective optimization effect ZW7I:FEA,FUL
BSC
feature
Multipoint state Gbof
unsuccessful.
COMPLETE)
default
time
parameter
must slot
wait values.
4untiland
days
L:FEA=606;
1.Enter
Extended
Interface the
Paging
4.Activate
Enter
time
of
the the slot
BIM the
week,istables
--------------------- 4 done
the
must
following
BCCH
feature
at first to
withstateON LAC if
to
hanism to change the RXQUAL thresholds for AMR calls depending on the used ---------------------
message
following
be
clock
are
commandconfigured
time
updated
powe and
to
needed
ON
+ CI, if needed
BTS1, with
---------------------
monitoring the
command
as
period
before CCCHE
activate
command
(W7M). when theto
handover parameters to avoid unnecessary unpacking in intra-cell FR / HR handovers BTS2
PCU
switching and
-----------------
(ZOEM).
activate
before pooltime OSC DFCA slot
feature
W7M.
ZW7M:FEA=67:
BTS3 license:
areon. is
ZOEM;
DHR
6.
reallocation
hopping
ZW7M:FEA=18
ingle increase step from the default +2 up to +10 for Uplink Radio Link timeo ZW7M:FEA=18
The
ON;
paged.
10 newThen
Test theSEG leve
Monitoring
multiplexing
ZERM:BTS=<bt
done.
5.Make
02:ON:; sure isin
58:ON;
If
the you whole
activation
started. have Wait LAC,
the
2.Modify
4 BTS:
s_id>,TRX=<trx
ZEEQ:PPRD=<
thatCheckthe BIM
configured BSC
that
BTS1,
Expected
few minutes
ZEQM:BTS=<B
_id>:CH2=CCC
PCU
tables poolBTS2.
are so
specific
the feature
Multipoint
BTS3 and PAFILEGb
outcome
that
TS at
HE:CH4=CCCH
reallocation
successfully
parameter least
state
Interface
BTS4,
•Calls
one change
phone isby
are when
re- call of
identification>:
E:CH6=CCCHE
day>,PPRST=<
created
NMO
Extended
the I
feature to NMO
paged.
connected.
is made
DHRLIM
;PCU
printing pool during
out= the
II using
BCCH
state
4.Re-insertis CONF,the the
the
<Limit
Note monitoring.
for
that
reallocation
incoming
following the
succeeded
you
battery
•BSC
5.Stop mustis and
the up set turn
and
Triggering
Extended
start
interference
command:
using
the the
feature OSC
the MS
running.
message
DHR
CCCH on.
command
state
Connect
monitoring tochannel
time>,PPRP=<
BIM tables
ZEGP:19:01; ONthe
ofto
W7I.
s the radio channel capacity for voice calls in GSM networks. Multiplexing>;
can
PCU
the
This also
DFCApool be
(ZOES).tofeature
ZW7I:FEA,FUL
activate
MS
•The
configured BTS4
used
reallocation
BTS(s) (EQI). to
will
be
and activated
L:FEA=1858;
Multipoint
remove Gb the
parameter
ZOES;
the TRX
period>;
ZEQI
after bythe
h several SGSNs 5 Activate
Interface.
battery from
values
Monitoring
creating
:BTS=<BTS
approximately
Extended
are the theis
MS.
correct.
stopped.
TRX
automatically between PCUs within a PCU pool based on the load condition ofidentification>; with
e minutes Totheof
five
BCCH
5.Make Enabled
MTprint CS
check
6.Print
MML
6.Set this,
out
command
DFCA
ntial data services changing
parameter
call.
the
messageparameters
theasto
ERC.
DFCA
PAFILE
shown hopping
below.
CS
with call
EQO,
monitoring.
7 Unlock
mode (EQS,isthe
witched networks. Bandwidth savings are achieved thanks to Abis optimization parameter.
through
ZEQM:BTS=<bt
unsuccessful. If rem
the
ERO,
ZOEG;
BCCH
EQM,
the orTRX
EQS).
activation EEI
s_identification
Paging
commands•No
Copy isthe
message done
e BTS transmits at a 2 dB lower power level for the dummy bursts on idle timeslots Unlock
This
fails, of
requires
the the alarm B
>:EBENA=Y;
at first
alarms
monitoring with
are LAC
to
BCCH
locking
1347,
or TRX
the
CS is
e based application software. With a Double Power TRX, a module that has two + CI,transmitters
triggered.
text-file,
with
BTS. BTS4
MML for and four receivers can be exploited to gain
mber of SI2 quarter messages that are sent in a normal BCCH channel. When PAGING
ZEQM:SEG=<s
this
paged. feature
Then is in use, all the individual SI2 quarter messa
example,
command
ZEQS
COORDINATIO ERS.
2 quarter messages that are sent to the mobile stations (MS) and increases the eg_identificatio
the capacity
whole LAC,
aiv_bxsx.log of these messages. Reducing the number of S
ERS:BTS=<bts
:BTS=<BTS
N
n>:EBENA=Y;
BTS1,
7.Destroy
_id>,TRX=<trx_ BTS2.
identification>:L
ACTIVATION/D
BTS3 and and
capacity in the cell. It may be used for alleviating CCCH paging and access gr ;monitoring
id>:U;
EACTIVATION
BTS4,
free
ZEQM is re-
message
on the Common Control Channel (CCCH) in the Air interface. This feature solve FAILED
paged. is set.
n in BSC", the BSC performs CS paging coordination internally when in the network buffer.
:BTS=<BTS operation mode II (NOM II). The BSC forwards the p
ZOEQ;
identification>:::
Monitoring is
:DMOD=2;
es more secure air interface links to prevent hacking attacks than A5/1 encry ZEQS destroyed.
ranches which are equipped with the Multi Carrier Power Amplifier (MCPA). Each :BTS=<BTS MCPA can include up to 6 TRXs by keeping the TX p
identification>:
can not be more than 5(DA) medium access method. It enables a mobile to use U;
he Dynamic Allocation more uplink (UL) timeslots, and thus reach higher UL th
nal classes multislot, up and down TSL and up to 6
each 296 kbit/s
For
forced HO
instructions
timer>;
on installing
The timer BTS
licences,
site battery see
Overview
backup forcedof
Licensing in
o to provide improved link balance for Single Antenna Interference Cancellat HO timer (TIM)
BSC .is given in
value
3 Check the
seconds.
value of the
STIRC feature
y saving mechanism for Flexi EDGE BTS. This feature automatically shuts down stateTRXs or Dual TRXs when the traffic is low. This featur
(W7I).
ZW7I
:FEA,FULL:FEA
=393;
4 If
necessary,
change the
STIRC feature
state to ON.
ZW7M
:FEA=393:ON;
5 Check that
the STIRC
feature state
change
succeeded
(W7I).
ZW7I
:FEA,FULL:FEA
=393;
6 Change the
value of the
STIRC enabled
parameter of
the STIRC-
enabled BTS
object to Y
(EQM).
ZEQM
:BTS=<bts_id>
:STIRC=Y;
7 Check that
the value
change
succeeded
(EQO).
ZEQO
:BTS=<bts_id>
:MIS;
If you enable
STIRC before
the BCF/BTS
object is
unlocked, and
all unlocked
TRXs are not
STIRC
capable,
alarm 7606 is
raised and
the TRX is
set to
blocked (BL)
state.
instructed in BSS Integration.
•HR or DR (dual rate) channels are
created to the cells that are used for AMR
HR testing. The (E)GPRS DL Power Control feature
HR channel provides the following benefits to the
Licence key creation
controlled and activation is
features operator:
instructed
Dynamic SDCCH in Activating must and be active testinginHalf the
Rate.before •It
Byreduces
providingtransmit good voice power, which
quality and in turn
Check
BSC the software Increased andDynamic
hardware SDCCH
•Licencescan covering AMRinFR and AMR 实施优先 helps in reducing the
increased communication capabilities, interference in the 提升目标
requirements
Capacity described
be activated. BSS20960:
HR are installed 约束条件
as instructed in Licence 级 network,
to适用场景及增益Adapted
accelerate and hence
the the mobiles
return efficiency Scenario
of investment and 项
Wideband
Licence
If the key
licence AMR key and
controlled
（参数&特性） expires, BSS21118:
features
the additional TFO for
Implement •Increases
experience the
better network
Gain
radio conditions. as in Improved
Before
Management
AMR.
'•BSC
SDDCH you
S13 startin BSC.
software,
channels areorWhen later installing the Priority GSM
automatically less network,
radio no need aretoreserved
replace for the
Licence
Before
licences, youkey
the controlled
proceed
initial to
state features
activate
of the the
features IB- •It helps
existing inresources
reducingorBTS
equipment any power
hardware
Target
Make
•A licence
reconfigured sure that
covering
back the toAAMR and
traffic Abis
PPC interfaces
is
channels installed.
as signaling type of traffic.
•It
NACC is supported
should feature,
bereleased
set with
ensure RG20(BSS)
thatinLicensing
the EP2.0. High-直接实施Directly
following consumption.
are
For
they created
more astoinstructed
information, CONF. see BSS in the Implement Phone 话统OSS
•It is are
supported
prerequisites are in met:
UltraSite SW from •Makes
•It maintains network
voice quality more when Smartthe
Integration
BSC.
Need 64 kbit/sandsignalling
that full rate or dual rate
channels friendly as it allocates resources based
CX8.1
•NACC and
is in future
the releases
active statehalf rate data usage increases.
resources
•The
(TRXSIG) AMR are
full created.
rate or AMR on the needfunction rather than based on
•PCU2
Make
functionality is installed
sure thatmust the MSS, MGW and the The'EUTM can significantly
Only surpported bybe active
UltraSite/ in FLEXI
the BSC,BTS High-直接实施Directly
for railway,
handset's subway,
Implement
multislot
improve the performance of WAP highway
capability. location to a 话统OSS
•valid
TCSM3i
before IB-NACC
the AMR licence
support Wideband
PPC can is installed
beAMR and
activated. •Increases the number of PS users that
•SGSN
Tandem
For supports
Free Operation.
instructions RIM procedures browse,the
High-直接实施Directly
reduce download
cell
Implement and download
reselection causedsmall by dat话统OSS
can
files be
FTP simultaneously accommodated
The following
4、Turn the AMR network PPCelements feature states are on the throughput
Better radio resources.
EUTM
•The features
feature isTBF offorhigh
applicable
EDGE encodingMS
with
话统OSS
needed
'ON' for testing
if needed (W7M). the activation of •Reduces
accounted the
for, single blocking
slot as existing
throughputmore PS
WidebandAMR
Downlink AMR:PPC: GSM
users SAIC
can be handsets,
accommodated thus providingon the an 路测Drive Test
•1 MSS and MGW increased
immediate significantly
gain with just a software
ZW7M:FEA=578:ON;
BSC S14 EP9.1 same radio resource.
•1 upgrade in the GSM radio network.
It isTCSM3i
Uplink
PCU AMRifPPC:
PCU2
supported transcoding
with RG20(BSS) is performed in
after the implementation
the BSS
ZW7M:FEA=606:ON; •It increases the capacityofforand voice CS4 and CS3, due to the rate of improvem
Need to carry out BSC/BTS/ network
•1 BSC
5、Check thatand the other
change of the AMR releases capacity for data traffic without
management supporting
•1
PPC BTS feature states succeeded (W7I). requiring new TRXs or related
upgrades to improve the efficiency of data channel occupancy
Hardware
•2 Wideband
Downlink
•To operate AMR theAMR PPC: capable
feature, the MSS
license for hardware. This reduces the number of
Software requirements
BTS :OSC Half
ZW7I:FEA,FULL:FEA=578;
the feature BSS21454: Rate requires “Packet either
Abis over TRXs
to improve required to realize
the quality a specific
of voice calls and MOS value of mobile users
Table: Required software
UltraSite,
Uplink
Ethernet” AMR Flexi
must PPC: EDGE,
be installed.Flexi Multiradio, capacity
independent or spectral
UL/DL efficiency.
AMR link threshold can make a certain wireless co
Network element Software release improve customer perception
Flexi Multiradiolicense10
ZW7I:FEA,FULL:FEA=606;
•The IUA mustor Flexi CompactThis
be installed. base •The increased capacity per TRX
required
stations.
Before
is in order you Intothe beUltraSite
start able to base station,
create the reduces the energy consumption per
BSC S13
OSC Half
Make
association sureRate that
set requires
the
to following
OMUSIG the and use
network of
TRXSIG. user.
drop rateThisby reduces
half or the the energy
same rate of drop out rate of 15% of the traffic
Flexi EDGE BTS EP2.0
UltraSite
elements
The license EDGE
are TRX
available:
code is HW.
899. consumption required per Erlang
Licence UltraSite
key controlled EDGE features BTS CX6.0 ，The BSC S14 software CAPEX is required
savingsand & improved
there arenetwork no specific quality
hardware
by reducing
requirements
drop callfor
rate
th
MS
•BSC
•IPv4
Before :Capable
addresses
you start of SAIC and subnetsand AMR are significantly.
MetroSite EDGE BTS CXM6.0
Software
•BTS
planned.
Licence key the controlled •It avoids the need to add new sites, as
•To operate MSC/HLR Not features
feature, the license for
applicable Reduction in CS Dropped Call Ratio
Network
•PCU2
•S15feature orelement
level PCUM
CPULAN Required software it maintains the coverage area in
the “Extended
SGSN Notand BCCH”PCULAN
applicable must be The•reduced
reduced dropped
electricity callconsumption
rate in heavily
release
•MS
configuration
installed. with L3 connectivity capacity extensions.
NetAct OSS4.2 due loaded networks
BSC S16.1
Make
•The sure
ETP
cell you
ablehave
isplug-in to unit the following
is available
transfer thelater and
traffic. •Thetoincreased
•Improvementthe "Energy incapacity
BSC saving PCU mode
per TRXfor
utilization
Horizon BTS HR2 or BCCH •increased
TRX" coverage,
helps operators including
to through
reduce in-
Flexi
licenses: EDGE
commissioned.
•The BCFRequired BTS
site types EX5.1
Refer andCreating
software and the effectively
factor. reduces site density
Table software shows building
network operating coverage, costs. in lightly loaded
Flexi
•Gb
Managing
versions Multiradio
over IPversion
BSC
(currentlicenseBTS
Hardware
orthatis EX5.1
activated
newer) for used in
details. BSC.
are reduced
•Reduction combining
in CAPEX losses.
investments.
earliest supports Robust When this feature networks
is activated in the
UltraSite
•Packet
•The PCU iswith
compatible BTS
Abis CX9.1
over
available IP/Ethernet
theSignalling.and configured
feature. or Packet
See section to •When
•Increase another
in revenueradio technology
due to decreased needs
software AMR •FACCH most
network, and SACCH of the repetition
energy savingsimprove
Flexi
Abis
use
“4.1 Multiradio
over
Packet
Software TDM Abis. 10
license
For BTS
requirements” isGF1.0
details activated
refer in to
PS share
call the
drops samecaused site, by antennas
a single or are
PCU
Network Hardware
element requirements
Software release provided thethe
by C/Idummyby up toburst 4 dBpower
Flexi
BSC.
Activating
Network
Make Compact
sure and
element BTS
Testing
thatRequired
you have GFC1.0
BSS09006:
Required
installed software
the input ports
capacity of combiners may be
limitation.
required Table: hardware reduction during periods of low traffic,
NetAct
Network
•Dynamic
GPRS.
release
licences OSS5.3
element
for PCU2the CDPoolingSET
following:Required 2license software
is released
•OPEX by
saving theas introduction
radio network of OSC
Network element Hardware
mcBSC mcBSC requirements
Rel. 1 e.g. at night time. With dynamic power
release
installed.
•Configure
BSC
•Gb over BSC IPESB24-D LAN S14 deviceED MP5.0 (using Half Rate
resource with
allocation SAIC is MS.done
No requirements.
S14 control of active dedicated channels,
BSC
The
commands
Flexi following ZWT,features ZUS, S14
need
ZWY, EP3.2to ZW6be (or and automatically.
BTS EDGE
•PCU2
Flexi UltraSite
EDGE BTS
BTS and MetroSite EP3.0 TRXs MP3 have to provide core network disaster recovery and backup
higher)
configured
ZYF).
UltraSite
•Multipoint Three EDGE before
Gb new theEP3
LAN
BTS
Interface activation
topologies,
CX7.0 of T8,T9
MP3 this the
•The
•More
BSC
feature
paging
accurate
multiple
reduces
capacity
corePCU electricity
is enhanced
pool
network analysis
nodes by
in
to be
BTSplus
Flexi
feature.
and T10
EDGE-capable
EDGE BTS
are BTS
introduced.
or
BRG2
EP3
equipped
MP3
with an consumption
increasing
the PCU the
selection throughout
number algorithm.of the
CCCH day. to achieve load sharing
MetroSite
EDGE-capable
Before you EDGE
EDGE start BTS
BTSbaseband CX7.0 MP3 For
unit.Robust The reduced transmit power of dummy
UltraSite
•Packet
•Flexi
MetroSite EDGE BTS
Abis EDGE is configured
BTS with
BTS, CX7SW
the MP2
into
EXin4.0
Extended (or or
the higher)
PCUs.Flexi channels
The Flexible in the MCPA cell. TX The paging
Power Pooling
Tip:AMR
NetAct Signaling
Activate the is
feature
OSSnot supported
first
5.1 CD the
set onBSCs
2 a Increase
bursts, and cover the distance
limited dynamic power
BTSplus
Multiradio
BCCH BTS
support BTS with
is SW 09-40
implemented EX4.1. (or higher)
inTheBSC FIYA/ success
feature rate
providesfor is improved
theactive
following with large
benefits
Horizon
and
hardware then BTS
in the with
MSC atleast
to avoid one service
CTU TRX. control allowed CS channels,
Flexi
FIQA/ Multiradio
FIYB/ BTS1) EX3.1 MP1 (or location areas.
SW S14
disruption
BTS
higher) Flexi TCSMin FIQB
EP5.1
EDGE theNo (or module
higher)
orrequirements.
network. required by
UltraSite EDGE or to operators:
result
•Increasedin a reduction
use of packet in downlink
BTS
BTSplus
To
BTSplus
is available.
test theSGSN
HW No
activation 09-40
requirements.
of Intelligent •It allows the
interference operators
caused by thetoswitched
utilize
BCCH the(PS)
NetAct
Flexi Multiradio OSS5.2 CD Set 1 services is possible without being
Selective
Before
MetroSite2) you startBTS
Paging, make CX7
EX3.1
sureMP3
MP1the
that For
(or higher)
output
End user
frequency.
constrained
power of the MCPAs
experiences
by the access quality optimally.
grantusage in
Flexi
following Multiradio
network BTS,
As a precondition Flexi EDGE BTS needs elements the Extended
and mobileBCCH •It increases
terms of reduced the capacity
latency of the BTS for
hardware
support is implemented in BSC SW S14 channel
a given (AGCH) capacity.
coverage area without the need
stations
to
PCU be are
created available:
and EP2
PCU1, software
PCU2, attached
PCUM The
A5/3
•Due increase
ciphering
to the increased in paging
enables capacity
the operator
rate of success may tobe
in
Network
MP8
•1 MSC (or element
higher)
with activated Required
Intelligent software ofadditional
experienced Radio
as: Frequency (RF)
and
(required
release activated if the extended CCCH channel Increase
offer
paging, modern cover
calls are distance
encryption
established methods faster. in
NetAct Paging
Selective OSS5.2 CD Set 2 modules
•Fewer
order toand andpossibly
support alsothe helps larger in network
subscriber’s sitesmore can
rightbe to
is used with GPRS/EDGE
BSC S14 in the
EP3.2 •The
To revenue
improve
planning. the issystem
improved 're with
delay
•1 BSC
segment.) with S12 ED 4.1 or newer used
use secure
established/served communication calls. paths.
NetAct OSS5.0 CD Set1 •It reduces the call
software
Network
•Reduced
If the decryption Abis keydrop
signaling rate
loadinin CCCH
is unknown, the
•4 BTSs on one LAC and twohardware
element Required different coverage
TRX
decryption limited
probability networks. for A5/3 coding is
release
bands, each having at least one TRX •It enables
•Reduced the
probabilityuser toofenhance
paging overload
BSC PCU2 less than for A5/1 encryption.
coverage
Therefore, and capacity
electronic at the same on
eavesdropping
Send
time. the paging message'BSC not only or in the PCH channel is still the
A5/3 ciphered calls is morecoverage
It also enhances the difficult than
capacity individuallyones.
on A5/1 encrypted which results in
Need to install the LMU module on the flexibility.
MCPA can base
include station,
up to currently
6 TRXs by only support
keeping thefor TX power capac
broadband
improve speech quality and MOS value
more uplink (UL) timeslots, and thus reach higher UL throughput by removing the need for the mobile to detect uplink state flags (USFs)
Prior
maketothe theGPRS/EDGE
version of R4'3GPP, uplink peak up and rate down TSL and
up to 236.8 can not be mo
kbit/s
Release 3GPP 5 (TS 45.002) introduces the new terminal classes mu
HMC enables the GPRS/EDGE downlink peak rate to reach 296 kbit/
When this feature is activated in the
network, the operator can lower the
to enhance
network the MOS
operating value,
costs reduce the words
by reducing
energy consumption. In Flexi EDGE
energy saving
BTS, the andsaves
operator emission reduction,
around 40 W and reduce network interferenc
by powering down one dual TRX.
TRXs or Dual TRXs when the traffic is low. This feature is controlle
to enhance PCU capacity
少系统
RTT（Ro
und Trip
Timers）
其它可能时间和
受影响的 TCP慢启
路测和话动效应的
统KPI 影响。
其它影响应用局点
及效果 EUTM功
Other
DT&OSS Other
Influence (S国S局) 能可以显
KPI that 著提高
may be WAP浏览
Influence 通过提供良好的语音质量和增加通话能力，加速
，图铃下 GSM网络投资的回报，无需更换现有设备或任何硬
d 载和小文
改善网络下行干扰
件FTP下
对于铁路沿线、地铁、高速公路的位置区边界,避免SD拥塞
载的性能
EUTM功
减少了由于小区重选造成数据停传的时间，增加速率
能对高编
码占比、
Better throughput for EDGE MS
单时隙吞
吐率提升
路测Drive Test 明显在使用
AMR的情
较大程度的改善无线信道使用的效率，提升单信道承载速率指标以及降低数据拥塞。在资源受
况 improve the utilization of wireless resources, as well as to improve the user's percep
S3, due to the rate of improvement, you can greatly
下，TCH
提高了移
实施CS3 and CS4之后，由于速率的提升，可以较大程度的改善无线资源的利用，以及
对抗恶劣
动用户的
el occupancy 无线条件
语音通话
提高数据信道占用效率
的能力得
质量和MOS
MOS value of mobile users 值以大大提
can make a certain wireless condition to obtai高，但是 UL/DL链路门限可以使得一定无线条件下获得更有效的优化效果
独立的AMR
对于信令
提高客户感知
信道并未
改善，如
op out rate of 15% of the traffic gain, which 掉话率减半或同样的掉话率水平下15%的话务量增益，也相当于同样话务量节约能耗15％
果经过多
ality by reducing drop call rate 次重传之
CAPEX savings & improved network quality by reducing drop call rate
后信令消
息仍未被 in CS Dropped Call Ratio
Reduction
正确解码
(acknowle
dged)，连
接会被释
放，造成
提供核心
掉话，此
网的容灾
功能改善
，冗余备
份信令导致
的掉话
BSC的多
个核心网
提升网络容量
节点间实
BSC下发
ry and backup 更加有效
现负荷分
寻呼消息
地使用
hieve load sharing 担
时不仅在
Abis/Gb
传统的
接口资源
PCH信道
还在
增加覆盖距离
3GPP R4
PACCH信
之前的版
道进行联
本中，上
合寻呼从
下行TSL
通过降低功耗来大幅节省运维费用
而避免手
的和不能
机在分组
超过5
传输状态
3GPP
时由于无
增加覆盖距离
release
法接收 5
改善系统间重选延时
(TS
PCH信道
45.002)引
的寻呼消
通过扩大CCCH信道容量实现单位时间内paging消息的最大传送，从而解决空口paging传输瓶
息而导致
入新的终
无法接收
端multislot
寻呼精确度进一步提高，寻呼负荷进一步减少；
CS业务。
classes，
y in the PCH channel is still the traditional 上下行
TSL的和
在无线接口上的高度安全模式杜绝偷听
达到6
HMC
More 使 distant and weak CS&PS connection can be served
GPRS/ED
改善语音质量和MOS值
GE下行峰
down TSL and can
e up to 236.8 kbit/s not be more than 5 值速率达
使GPRS/EDGE上行峰值速率达到236.8 kbit/s
es the new terminal classes multislot, up and 到296
down TSL and up to 6
nk peak rate to reach 296 kbit/s kbit/s
提升MOS值，减少掉话
and reduce network interference 节能减排,降低网络干扰
节能减排,降低网络干扰
提升PCU容量
报，无需更换现有设备或任何硬件
以及降低数据拥塞。在资源受限的情况下，可以有效的提升用户感知。
善无线资源的利用，以及改善用户感知
同样话务量节约能耗15％
，从而解决空口paging传输瓶颈的问题，有助于LAC的划分以及寻呼成功率的提高
返回 Back
影响程度（高/中/低）
告警的代码告警名称 Influence(Major,Medium, 故障描述
Alarm ID Alarm Name Meaning
Minor)
7604 BTS OPERATION DEGRADED Medium
7606 TRX FAULTY Medium
7738 BTS WITH NO TRANSACTIONS Major
7767 BCCH MISSING Major
7744 EXCESSIVE TCH INTERFERENCE Major
7745 CHANNEL FAILURE RATE ABOVE DEFINED Major
7746 CH CONGESTION IN BTS ABOVE DEFINED Major
2725 ADJACENT CELL IDENTIFIER CONFIGURAT Major
7164 MASTER CLOCK UNIT HARDWARE FAULTYMajor
GPRS
7725 TRAFFIC CHANNEL ACTIVATION FAILURE Major
3033 UNKNOWN ROUTING AREA OR LOCATIONMedium
3068 EGPRS DYNAMIC ABIS POOL FAILURE Medium
3073 FAULTY PCU PCM TIMESLOTS IN PCU Medium
3164 PCU PROCESSOR OVERLOAD ALARM Medium
3273 EGPRS TERRITORY FAILURE Medium
7730 CONFIGURATION OF BCF FAILED Medium
2993 BTS AND TC UNSYNCHRONIZATION CLEARMajor
7607 TRX OPERATION DEGRADED Medium
8099 RECEIVED BIT ERROR RATIO (BER) > 1E-3 Major
处理建议
Instructions
Antenna alarm: according to the a

Fault: the replacement of TRX
No business warning: restart
Interference alarm: find the interference
Slot allocation failure alarm: the replacement
Channel congestion alarm: open half rate or
Neighbor cell configuration error alarm: accor
Clock alarm: change alarm hardware
GENA or PCU to solve the switching

Related to SGSN side, LAC/RAC configuratio
Configuration or hardware, PCU capacity will
GSWB hardware issues, PCU capacity will r
PCU load is high, if the need to adjust
Congestion due to insufficient PCU resource
BCF configuration and hardware does not ma
Transmission fault and fault frequency
Replace TRX
Notification transfer view fault
编专题/Topic
修订记录/Edit 编者/Edited by 版日期/Date
厂家制式号/Sn Record 本/Version
1 新开发
CS接入性Call Setup Success Rate 赵博 WX395795 V1.11
2 新开发
CS移动性 Handover Success Rate 赵博 WX395795 V1.11
NOKIA 3 CS保持性 TCH Drop Rate 新开发赵博 WX395795 V1.11

GSM
4 新开发
PS 接入性TBF ESTABLISHMENT SUCCESS RATE 赵博 WX395795 V1.11
5 PS 保持性TBF DROP RATE 新开发赵博 WX395795 V1.11

评审/Reviewed by 版日期/Date
本/Version
chenjing 00338617,maominghui 00285487,minge V1.1
00205821,luoying 00162429,caimingliang 00280373



1、删除了载频故障，因为不能
版本V1.11变动说明
1、更新TCH拥塞次数（含切）公式版本V1.12变动说明
1、电平质量分布上下行分开对应具体指标
版本V1.13变动说明
2、法国公式澄清I finally get
2、更新了4~5级干扰比例公式 2、0~4级质量占比，上下行分开 the explanation for [0.0] it
3、增加了上下行弱覆盖比例 3、TA分布改为0~63表示 means that if the value of
1、更新TCH拥塞次数（含切）公式
4、对核查邻区做了文字性描述 4、增加切入和切出成功率
2、更新了4~5级干扰比例公式 1、电平质量分布上下行分开 the denominator = 0 then we
5、参数在形式上的完善 5、增加小区到小区切换成功率
2、0~4级质量占比，上下行分开 have to take the value 0
3、增加了上下行弱覆盖比例
6、增加了TA分布 6、增加法国考核公式
3、TA分布改为0~63表示
4、对核查邻区做了文字性描述 1、电平质量分布上下行分开 For example: If X= A /
1、更新TCH拥塞次数（含切）公式 4、增加切入和切出成功率
2、0~4级质量占比，上下行分开 [0.0] B and B =0 then X = 0
5、参数在形式上的完善
2、更新了4~5级干扰比例公式
6、增加了TA分布 5、增加小区到小区切换成功率
4、参数在形式上的完善 4、增加切入和切出成功率 1、删除了PCU,EDAP拥塞率公式
3、更新了PCU,EDAP拥塞率公式 1、电平质量分布上下行分开
5、增加小区到小区切换成功率，因为该指标不能对应到小区，
5、增加了TA分布 2、0~4级质量占比，上下行分开
4、更新了上下行TBF阻塞率公式 6、增加法国考核公式会使软件复杂
5、参数在形式上的完善 4、增加法国考核公式 2、更新了GPRS上、下行RLC层流
6、增加了TA分布 1、电平质量分布上下行分开 1、更新了GPRS上、下行RLC层流
量公式，单位为（Kbyte)
7、增加了相关PS资源的告警 2、0~4级质量占比，上下行分开量公式，单位为（Kbyte)
3、参数在形式上的完善 3、TA分布改为0~63表示 2、删除了硬件故障，因为不能
4、增加了TA分布 4、增加法国考核公式对应具体的建议
版本V1.14变动说明版本V1.15变动说明-骆瑛162429
更新了静态&动态PDCH配置时隙数公式
格式调整为X板斧格式
更新了静态&动态PDCH配置时隙数公式
1、要求能够支持对接入性(CSSR，立即指配成功率，指配成功率)，保持性(TCH掉话率,SDCCH掉话
率)，移动性(切换成功率)、完整性(上下行语音质量占比)，资源容量(SDCC拥塞率，TCH拥塞率)等
指标分析；
2、要求逻辑树能够清晰的呈现分析该项指标的流程和关键动作；
3、要求详细描述辅助分析指标的公式或Counter，意义，造成指标异常的可能原因，处理建议等；
4、要求详细描述相关参数的MO归属，意义，调大调小的影响，调整建议等；
5、要求详细描述相关告警的代码，影响程度，故障描述，处理建议等；
6、要求详细描述相关特性的功能，参数的意义及调整建议等。

Action 1: Determine The Scope of Problems

Uploaded by

Copyright:

Available Formats

Action 1: Determine The Scope of Problems

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Action 1: Determine The Scope of Problems

Uploaded by

Copyright:

Available Formats

呼叫建立成功率Call Setup Success Rate

Required Steps Required Actions KPI 名称(Chinese Name)

Action 1: Determine the scope of problems

Action 2.1:Alarm Checking

Except above, if other alarms exist, please list them

Action 2.2: Parameters Checking

(Cell Level) Interference Analysis 小区级上行0~4级质量占比

KPI Name(English Name) Counter/Formula Tables Name

Call Setup Success Rate--india

Alarm Name Influence(Major,Medium,Minor) Meaning

BTS OPERATION DEGRADED Medium 0

ABBREV Value Range Reference Val

g and Analysis functions

Feature's Meaning Adapted Scenario and Gain

Not available time NOT_AVAIL_TIME Counters from

if local formula is not the same 切换成功率--印度 Handover Success Rate--India

Action 2.1：Alarm Checking

7606 TRX FAULTY

7738 BTS WITH NO TRANSACTIONS

7767 BCCH MISSING

Mandatory checking 7744 EXCESSIVE TCH INTERFERENCE

7745 CHANNEL FAILURE RATE ABOVE DEFINED THRESHOLD

7746 CH CONGESTION IN BTS ABOVE DEFINED THRESHOLD

2725 ADJACENT CELL IDENTIFIER CONFIGURATION ERROR

7164 MASTER CLOCK UNIT HARDWARE FAULTY

8099 RECEIVED BIT ERROR RATIO (BER) > 1E-3

Action 2.2: Parameters Checking

Action 2.4: Feature Checking

Feature Name Feature's Meaning

STIRC STIRC is designed to cancel uplink interference and als

Action 3.1: Identify Handover Fail Causes

切换成功率(切入） Handover success rate（in）

切入成功率(小区对小区） Handover success rate（in cell to cell ）

下行弱覆盖比例 DL Weak coverage rate

平均TA值 Ave TA distance

下行0~4级质量占比 DL HQI KPI

(Cell Level) Interference Analysis

4~5级干扰比例 Interferences KPIs

载频级掉话 Drop call number in TRX

载频级0~5级质量占比 TRX Quality

载频级分配失败次数 CALL FAIL NUMBER IN TRX

Action 3.3: Capacity Analysis

TCH拥塞次数（不含切） TCH Congestion num (not include handover)

TCH拥塞次数（含切） TCH Congestion num (include handover)

TCH话务量 Average TCH traffic

TCH全速率话务 Average FTCH traffic

每线话务量 AVE ERL PER CHANNEL

数据业务等效话务量 AVE PS traffic

切入时缺少资源数 Number of lack of radio resources during incoming han

切出时缺少资源数 Number of lack of radio resources during outgoing han

Inter-PLMN MSC 控制的的切出时，因为对方小区没有资源而导致的失败次数

Action 3.4: Transmission Anaysis

一般误码秒 Error second

严重误码秒 Serious error second

Action 3.5: RF Tunnel Analysis

Counters from table(s):

Influence(Major,Medium,Minor) Meaning Instructions

Medium 0 Fault: the replacement of TRX

Major 0 No business warning: restart

(5…43 step 2) GSMdBm 33 When the mobil

(0…30 step 2) DCSdBm 30 When the mobil