Scribd
Upload
26 views2 pages

WWW - Substech.com Dokuwiki Doku - PHP Id Drawing

The document discusses the metal forming process of drawing. Drawing involves pulling a workpiece made of metal through a die to reduce its cross-sectional area. The drawing process uses a series of dies with openings that gradually decrease in size. As the workpiece passes through each die, its length increases as its cross-sectional area decreases. Friction from passing through the dies causes heating at the workpiece surface which can result in sticking or breaking if not properly lubricated. Drawing is used to produce small diameter wires and seamless tubes from metals like steel and brass.

Uploaded by

rahul srivastava
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
26 views2 pages

WWW - Substech.com Dokuwiki Doku - PHP Id Drawing

The document discusses the metal forming process of drawing. Drawing involves pulling a workpiece made of metal through a die to reduce its cross-sectional area. The drawing process uses a series of dies with openings that gradually decrease in size. As the workpiece passes through each die, its length increases as its cross-sectional area decreases. Friction from passing through the dies causes heating at the workpiece surface which can result in sticking or breaking if not properly lubricated. Drawing is used to produce small diameter wires and seamless tubes from metals like steel and brass.

Uploaded by

rahul srivastava
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Drawing [SubsTech] Page 1 of 2

Roll Forming Machine


Colored steel / cold roll forming machine,etc.China factory direct.
www.hbfxywj.com
Ads by Google

Metal Forming PDF


Deep Drawing Steel
Sheet Metal Work

Ads by Google Metal Stamping Dies Steel Stamping Hot Forming CNC Wire Forming

to Metals
to Metal forming technologies

Drawing
Dr. Dmitri Kopeliovich

Drawing is a metal forming process involving pulling a workpiece (cold or hot) through a die providing
reduction of the cross section of the workpiece.

The drawing process employs a series of dies


with opening of similar shape and of size
which is slightly reduced in each consequent
die.

As the cross section decreases after passing


each die, the length of workpiece increases,
requiring corresponding increase of the
speed.

The draw force is dependent on the yield


strength of the metal, reduction of the cross
section area (amount of deformation),
contact area of the bar with the die and the
coefficient of friction.

Friction and deformation in the die cause heating the workpiece (wire, tube, rod) surface and may result in
sticking and breaking.

Contact friction, which is about a half of the total draw force, is controlled by lubricating the bar before it
enters the die.

When the total amount of deformation is too large and the wire undergoes hardening as a result of the
previous cold work operations, drawing is carried out in steps with annealing after each step.

Dies are made of alloy steel (die steel) hard alloys and diamond (drawing steel wires).

Drawing provides good surface quality and very low dimensions tolerances.

http://www.substech.com/dokuwiki/doku.php?id=drawing 10/11/2012
Drawing [SubsTech] Page 2 of 2

Drawing is used for production of wires (diameter down to 2µm) , seamless tubing, rods and other products
from brass and steel.

to top

Related internal links

■ Rolling
■ Forging
■ Extrusion
■ Deep drawing
■ Steel strip processing
■ Shot peening
■ Laser peening
■ Plastic deformation
■ Imperfections of crystal structure

Related external links

https://www.tntech.edu/me/courses/Zhang/ME30103110/Chap11pt5.ppt
[https://www.tntech.edu/me/courses/Zhang/ME30103110/Chap11pt5.ppt]
http://mechatronic.me.hfu.edu.tw/Luo2/2Forming.pdf [http://mechatronic.me.hfu.edu.tw/Luo2/2Forming.pdf]
http://courses.washington.edu/courseli/me355/Lectures/Sp2006/lecture10-11-Bulk%20Deformation%
20Processes.ppt [http://courses.washington.edu/courseli/me355/Lectures/Sp2006/lecture10-11-Bulk%
20Deformation%20Processes.ppt]
http://iesu5.ust.hk/dfaculty/ajay/courses/ieem215/lecs/3_forming.pdf
[http://iesu5.ust.hk/dfaculty/ajay/courses/ieem215/lecs/3_forming.pdf]

to Metals
to Metal forming technologies
drawing.txt · Last modified: 2012/05/31 by dmitri_kopeliovich

Ads by Google Steel Rolling Mill Steel Bar Stainless Steel Mechanical Drawing

Except where otherwise noted, this work is licensed under a Creative Commons Attribution-
Noncommercial-Share Alike 3.0 License

http://www.substech.com/dokuwiki/doku.php?id=drawing 10/11/2012

You might also like