What Is The Relationship Between Pressure Drop and Flow Rate in A Pipeline?

Relationship Between Pressure Drop and Flow Rate in a
Pipeline
What is the relationship between pressure drop and flow

rate in a pipeline?
by Jeff Sines, Senior Product Engineer at Engineered Software, Inc.
To understand the relationship between the pressure drop across a pipeline and the flow rate
through that pipeline, we need to go back to one of the most important fundamental laws that
governs the flow of fluid in a pipe: the Conservation of Energy, which for incompressible
liquids, can be expressed using the Bernoulli Equation.
Total Fluid Energy

Daniel Bernoulli, a Swiss mathematician and physicist, theorized that the total energy of a
fluid remains constant along a streamline assuming no work is done on or by the fluid and no
heat is transferred into or out of the fluid. The total energy of the fluid is the sum of the
energy the fluid possesses due to its elevation (elevation head), velocity (velocity head), and
static pressure (pressure head).
Total Energy=Elevation Head+Velocity Head+Pressure HeadT
otal Energy=Elevation Head+Velocity Head+Pressure Head
or:
TE=Z+v22g+144PρTE=Z+v22g+144Pρ
where (in US Imperial Units):
 TE = total fluid energy (feet of fluid)

 Z = elevation of the fluid measured from a reference plane (feet)
 v = fluid velocity (feet/sec)
 g = gravitational constant (32.2 ft/sec2)
 P = static pressure (psi, or lb/in2)
 ρ = fluid density (lb/ft3)
 144 = conversion from in2 to ft2
Bernoulli Equation Applied Between Two Points

In reality, the flow of fluid between two points cannot be achieved without a loss of fluid
energy due to friction and changes in momentum. The energy loss, or head loss, is seen as
some heat lost from the fluid, vibration of the piping, or noise generated by the fluid flow.
Head loss is a reduction in the capability of the fluid to do work and will act to reduce the
static pressure of the fluid.
Between two points, the Bernoulli Equation can be expressed as:
Z1+v212g+144P1ρ=Z2+v222g+144P2ρ+HLZ1+v122g+144P1ρ=Z2+v222g+1
44P2ρ+HL
where:
 1 = upstream location
 2 = downstream location
 HL = head loss between the upstream and downstream locations (feet of fluid)
The Bernoulli Equation can now be re-arranged to show that the change in static pressure (dP
= P1 - P2) is due to three components: a change in elevation, a change in velocity, and the
energy lost to heat, noise, and vibration:
(P1−P2)=ρ144[(Z2−Z1)+(v22−v212g)+HL](P1−P2)=ρ144[(Z2−Z1)+
(v22−v122g)+HL]
Pressure Change due to Elevation Change

The change in elevation can either be positive or negative. In other words, the upstream
location can be at a lower or higher elevation than the downstream location. If the fluid is
flowing up to a higher elevation, this energy conversion will act to decrease the static
pressure. If the fluid flows down to a lower elevation, the change in elevation head will act to
increase the static pressure.
For example, evaluating just the change in elevation, consider 60 °F water flowing up a hill
from an inlet elevation of 25 ft to an outlet elevation of 75 ft:
(P1−P2)=ρ144(Z2−Z1)=62.4lbft3144in2ft2(75−25ft)=21.7 psi(P1−P2)=ρ144
(Z2−Z1)=62.4lbft3144in2ft2(75−25ft)=21.7 psi
The positive value of dP indicates that the inlet pressure is greater than the outlet pressure, so
pressure will decrease by 21.7 psi solely due to the change in elevation of the fluid as it flows
uphill. Conversely, if the fluid is flowing down hill from an elevation of 75 ft to 25 ft, the
result would be negative and there will be a 21.7 psi gain in pressure and the outlet pressure
will be greater than the inlet pressure.
Pressure Change due to Velocity Change

Fluid velocity will change if the internal flow area changes. For example, if the pipe size is
reduced, the velocity will increase and act to decrease the static pressure. If the flow area
increases through an expansion or diffuser, the velocity will decrease and result in an increase
in the static pressure. If the pipe diameter is constant, the velocity will be constant and there
will be no change in pressure due to a change in velocity.
As an example, if an expansion fitting increases a 4 inch schedule 40 pipe to a 6 inch
schedule 40 pipe, the inside diameter increases from 4.026" to 6.065". If the flow rate
through the expansion is 368 gpm, the velocity goes from 9.27 ft/sec to 4.09 ft/sec. The
change in static pressure across the expansion due to the change in velocity is:
(P1−P2)=ρ144(v22−v212g)=62.4lbft3144in2ft2((4.09 ft/sec)2−(9.27 ft/
sec)22(32.2ft/sec2))=−0.466 psi(P1−P2)=ρ144(v22−v122g)=62.4lbft3144in2ft2
((4.09 ft/sec)2−(9.27 ft/sec)22(32.2ft/sec2))=−0.466 psi
The negative value of dP indicates that the outlet pressure will be greater than the inlet
pressure. In other words, pressure has increased by almost 0.5 psi from inlet to outlet solely
due to the conversion of velocity head to pressure head.
Pressure Change due to Head Loss

Since head loss is a reduction in the total energy of the fluid, it represents a reduction in the
capability of the fluid to do work. Head loss does not reduce the fluid velocity (consider a
constant diameter pipe with a constant mass flow rate), and it will not be effect the elevation
head of the fluid (consider a horizontal pipe with no elevation change from inlet to
outlet). Therefore, head loss will always act to reduce the pressure head, or static pressure, of
the fluid.
There are several ways to calculate the amount of energy lost due to fluid flow through a
pipe. The two most common methods are the Darcy-Weisbach equation and the Hazen-
Williams equation. The root form of the Darcy equation can be found in the Crane TP-410,
among other industrial references, and is:
HL=fLDv22gHL=fLDv22g
where:
 HL = head loss (feet)

 f = Darcy friction factor (dimensionless)
 L = pipe length (feet)
 D = pipe inside diameter (feet)
 v = fluid velocity (ft/sec)
 g = gravitational constant (32.2 ft/sec2)
The Darcy friction factor, f, takes into account the pipe roughness, diameter, fluid viscosity,
density, and velocity by first calculating the Reynolds Number and Relative Roughness. Once
calculated, the head loss can then be converted to a change in pressure using:
dP=ρHL144dP=ρHL144
There are other forms of the Darcy equation in the Crane TP-410 that use variables with
different units and a numerical constant that combines all the unit conversions together. For
example:
dP=2.161∗10−4(fLρQ2d5)dP=2.161∗10−4(fLρQ2d5)
where:
 Q = flow rate (gpm)

 d = pipe diameter (inches)
The graph below shows the resulting pressure drop for water at 60 F over a range of flow
rates for a 100 foot long pipe for both 4 inch and 6 inch schedule 40 piping.
Summary
To determine the total change in the static pressure of a fluid as it flows along a pipeline, all
three components of the Bernoulli Equation must be considered individually and added
together. A change in elevation may cause the pressure to decrease, a change in velocity may
cause it to increase, and the head loss may cause it to decrease. The net effect will depend on
the relative magnitudes of each change.
It is possible that the static pressure of the fluid actually increases from inlet to outlet if the
change in elevation or velocity results in an increase of pressure greater than the decrease that
results due to head loss.
The old saying that "fluid always flows from high pressure to low pressure" is not quite
accurate. The more accurate way to state this is that "fluid always flows from a region of
higher total energy to a region of lower total energy".

What Is The Relationship Between Pressure Drop and Flow Rate in A Pipeline?

Uploaded by

Copyright:

Available Formats

What Is The Relationship Between Pressure Drop and Flow Rate in A Pipeline?

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

What Is The Relationship Between Pressure Drop and Flow Rate in A Pipeline?

Uploaded by

Copyright:

Available Formats

Relationship Between Pressure Drop and Flow Rate in a

What is the relationship between pressure drop and flow

Total Fluid Energy

where (in US Imperial Units):

 TE = total fluid energy (feet of fluid)

Bernoulli Equation Applied Between Two Points

Pressure Change due to Elevation Change

Pressure Change due to Velocity Change

Pressure Change due to Head Loss

 HL = head loss (feet)

 Q = flow rate (gpm)

You might also like