GOVT.

COLLEGE OF ENGINEERING,
AMRAVATI

B. Tech. (Instrumentation)
V & VI Semester
Department of Instrumentation Engineering
2012-13

Page 1 of 33
 GOVERNMENT COLLEGE OF ENGINEERING AMRAVATI
DEPARTMENT OF INSTRUMENTATION ENGINEERING
PROPOSED SCHEME FOR B.Tech.( Instrumentation Engineering )
Evaluation Scheme
Teaching Scheme
Theory Practical
Course
Name of the course Theory Credits
Code Tutorial Practical Total
Hrs Total TA CT1 CT2 ESE ICA ESE
Hrs/week Hrs/week
/week

Sem III
SHU303 Engineering Mathematics III 3 0 --- 3 10 15 15 60 --- --- 100 3
INU 302 Electronic Devices and Circuits 3 1 --- 4 10 15 15 60 --- --- 100 4
INU303 Numerical Methods 3 1 --- 4 10 15 15 60 --- --- 100 4
INU304 Circuit Theory 3 --- --- 3 10 15 15 60 --- --- 100 3
INU305 Digital Electronics 3 --- --- 3 10 15 15 60 --- --- 100 3
INU306 Electronic Devices and Circuits Lab --- --- 2 2 --- --- --- --- 25 25 50 1
INU307 Circuit Theory Lab --- --- 2 2 --- --- --- --- 25 25 50 1
INU308 Digital Electronics Lab --- --- 2 2 --- --- --- --- 25 25 50 1
INU309 Computational Method Lab -I --- --- 2 2 --- --- --- --- 50 -- 50 1
SHU305 General Proficiency II 1 2 3 -- -- -- -- 25 25 50 2
Total 16 2 10 28 50 75 75 300 150 100 750 23
Sem IV
SHU401 Engineering Mathematics IV 3 - --- 3 10 15 15 60 --- --- 100 3
INU402 Sensors and Transducer 3 1 --- 4 10 15 15 60 --- --- 100 4
INU403 Control System Component 3 1 --- 4 10 15 15 60 --- --- 100 4
INU404 Linear Integrated Circuits 3 -- --- 3 10 15 15 60 --- --- 100 3
EEU411 Signals and Systems 3 1 --- 4 10 15 15 60 --- --- 100 4
INU406 Sensors and Transducer Lab --- --- 2 2 --- --- --- --- 25 25 50 1
INU407 Control System Component Lab --- --- 2 2 --- --- --- --- 25 25 50 1
INU408 Linear Integrated Circuits Lab --- --- 2 2 --- --- --- --- 25 25 50 1
INU 409 Computational Method Lab -II -- -- 2 2 --- -- -- -- 25 25 50 1
SHU403 Engineering Mathematics Lab --- --- 2 2 --- --- --- --- 50 -- 50 1
Total 15 3 10 28 50 75 75 300 150 100 750 23

Page 2 of 33
 GOVERNMENT COLLEGE OF ENGINEERING AMRAVATI
DEPARTMENT OF INSTRUMENTATION ENGINEERING
PROPOSED SCHEME FOR B.Tech.( Instrumentation Engineering )

Evaluation Scheme
Teaching Scheme
Theory Practical
Course
Name of the course Theory Credits
Code Tutorial Practical Total
Hrs Total TA CT1 CT2 ESE ICA ESE
Hrs/week Hrs/week
/week

Sem V
INU501 Microprocessor and Interfacing 3 1 --- 4 10 15 15 60 --- --- 100 4
INU502 Instrumental Methods of Analysis 3 --- --- 3 10 15 15 60 --- --- 100 3
INU503 Digital Signal Processing 3 --- --- 3 10 15 15 60 --- --- 100 3
INU504 Electronic Instrumentation 3 --- --- 3 10 15 15 60 --- --- 100 3
INU505 Control System Engineering 3 --- --- 3 10 15 15 60 --- --- 100 3
INU506 Microprocessor and Interfacing Lab --- --- 2 2 --- --- --- --- 25 25 50 1
INU507 Instrumental Methods of Analysis Lab --- --- 2 2 --- --- --- --- 25 25 50 1
INU508 Electronic Instrumentation Lab --- --- 2 2 --- --- --- --- 25 25 50 1
INU509 Digital Signal Processing Lab --- --- 2 2 --- --- --- --- 25 25 50 1
INU510 Control System Engineering Lab 2 2 --- --- --- --- 25 25 50 1
INU511 Self Study-I --- --- --- --- 25 --- --- --- --- --- 25 2
Total 15 1 10 26 75 75 75 300 125 125 775 23
• The self study I is based on INU501,INU502,INU503,INU504,INU505 class test each on the basis of 20% curriculum of the courses declared by the course
coordinator at the beginning of semester
• One faculty member should be appointed as course coordinator for self study I & his/her teaching work load shall be considered one hour per week
Sem VI
INU601 Microcontroller and It's Application 3 --- --- 3 10 15 15 60 --- --- 100 3
INU602 Power Electronics 3 --- --- 3 10 15 15 60 --- --- 100 3
INU603 Material Science and Process 3 --- --- 3 10 15 15 60 --- --- 100 3
INU604 Process Control 3 1 --- 4 10 15 15 60 --- --- 100 4
INU605 Project Engineering and Management 3 -- --- 3 10 15 15 60 --- --- 100 3
INU606 Microcontroller and It's Application Lab --- --- 2 2 --- --- --- --- 25 25 50 1
INU607 Power Electronics Lab --- --- 2 2 --- --- --- --- 25 25 50 1
INU608 Process Control Lab --- --- 2 2 --- --- --- --- 25 25 50 1
INU609 Minor Project --- --- 2 2 --- --- --- --- 25 25 50 2
INU610 Self Study-II --- --- --- --- 25 --- --- --- --- 25 2
INU611 Industrial Lecture -I 1 --- --- 1 --- --- --- --- --- --- --- ---
Total 16 1 8 25 75 75 75 300 100 100 725 23
• The self study-II is based on INU601,INU602,INU603,INU604,INU605 class test each on the basis of 20% curriculum of the courses declared by the course
coordinator at the beginning of semester
• One faculty member should be appointed as course coordinator for self study II & his/her teaching work load shall be considered one hour per week
• Credit shall be awarded on the basis of combined assessment of Industrial Lectures-I & Industrial Lectures-II

Page 3 of 33
 GOVERNMENT COLLEGE OF ENGINEERING AMRAVATI
DEPARTMENT OF INSTRUMENTATION ENGINEERING
PROPOSED SCHEME FOR B.Tech.( Instrumentation Engineering )
Evaluation Scheme
Teaching Scheme
Theory Practical
Course
Name of the course Theory Credits
Code Tutorial Practical Total
Hrs Total TA CT1 CT2 ESE ICA ESE
Hrs/week Hrs/week
/week
Sem VII
3
INU701 Distributed Control System 3 --- --- 3 10 15 15 60 --- --- 100
INU702 Biomedical Engineering 3 --- --- 3 10 15 15 60 --- --- 100 3
INU703 Elective-I 3 --- --- 3 10 15 15 60 --- --- 100 3
INU704 Interdisciplinary Elective 3 --- --- 3 10 15 15 60 --- --- 100 3
INU705 Distributed Control System Lab --- --- 2 2 25 25 50 1
INU706 Biomedical Engineering Lab --- --- 2 2 --- --- --- --- 25 25 50 1
INU707 Elective-I Lab --- --- 2 2 --- --- --- --- 25 25 50 1
INU708 Project- I --- --- 4 4 --- --- --- --- 50 --- 50 2
INU709 Seminar --- --- 2 2 --- --- --- --- 25 25 50 2
INU710 Industrial Training/ Visit --- --- --- 0 --- --- --- --- 50 --- 50 1
INU711 Industrial Lecture II 1 --- --- 1 --- --- --- --- 25 --- 25 1
INU712 Self Study-III --- --- --- 0 25 --- --- --- --- --- 25 2
Total 13 0 12 25 65 60 60 240 225 100 750 23
• Interdisciplinary electives will be offered to students other than this department
• The self study-III is based on INU701,INU702,INU703,INU705 class test each on the basis of 20% curriculum of the courses declared by the course coordinator at
the beginning of semester
• One faculty member should be appointed as course coordinator for self study III & his/her teaching work load shall be considered one hour per week
• Credit shall be awarded on the basis of combined assessment of Industrial Lectures I & Industrial Lectures II
Sem VIII
INU801 Virtual Instrumentation 3 1 --- 4 10 15 15 60 --- --- 100 4
INU802 Power Plant Instrumentation 3 1 --- 4 10 15 15 60 --- --- 100 4
INU803 Elective -II 3 --- --- 3 10 15 15 60 --- --- 100 3
INU804 Elective-III 3 --- --- 3 10 15 15 60 --- --- 100 3
INU805 Virtual Instrumentation Lab --- --- 2 2 --- --- --- --- 25 25 50 1
INU806 Elective-II Lab --- --- 2 2 --- --- --- --- 25 25 50 1
INU807 Project-II --- --- 6 6 --- --- --- --- 75 100 175 5
INU808 Self Study-IV --- --- --- --- 25 --- --- --- --- --- 25 2
Total 12 2 10 24 65 60 60 240 125 150 700 23
• The self study IV is based on INU801,INU802,INU803,INU804 class test each on the basis of 20% curriculum of the courses declared by the course coordinator at
the beginning of semester
• One faculty member should be appointed as course coordinator for self study IV & his/her teaching work load shall be considered one hour per week
Page 4 of 33
 # For project there will be 8 students in each batch (two groups of 4 students) * 1 hour working load to coordinate for coordination

INU703 INU704 INU803 INU804

A) Instrumentation A) Distributed Control A) Opto- Electronics
A) Image processing
System Design System Instrumentation

B) Instrumentation for B) Neural network

B) Sensors&
Agriculture &food and Fuzzy logic B) Adaptive Control
Transducer
processing control

C) Biomedical C) Biomedical Signal &

C) System Identification C) Advance Sensors
Instrumentation Processing
D) Nonlinear Control
D) Process D) Digital Control System
D) Embedded Systems
Instrumentation System

E) Introduction to
System Engineering

Page 5 of 33
 INU501 MICROPROCESSORS AND INTERFACING
Teaching Scheme : 03 L+01 T Total 04 Credit: 04
Evaluation Scheme: 15 CT1 + 15 CT2 +10 TA+ 60 ESE Total Marks: 100
Duration of ESE : 2hrs 30min.

Introduction to 8085: Architecture and operation, pin out diagram. Assembly

language programming for 8085 microprocessor instruction classification, instruction
set study in details, addressing modes, writing assembly language programs, stacks
subroutines, floating point routines. Instruction set timing diagrams, minimum
configuration for 8085.

Parallel I/O and Interfacing: In Basic interfacing concept, Memory- mapped I/O,
I/O mapped I/O concept interfacing memory. Interfacing memories EPROM and
RAM with 8085 with exhaustive and partial decoding techniques interrupt structure of
8085.

Interfacing with 8085: Interfacing with 8254, 8255, 8284, 8288, 0808, 0809,
interfacing seven segment displays keyboard, , RS 232, IEEE 488.

Introduction to 8086: Overview of 8086 Architecture. Signals and pins of 8086

microprocessor, Pin Diagram, Addressing Modes, Instruction set and Interrupt Table.

Assembly Language Programming of 8086: Fixed Point Arithmetic, Byte and

String Manipulation, Code Conversion, Assembler Directives and Operators.

Special Architectural Features And Related Programming: Stack Structure of

8086, Interrupts and Interrupt Service Routines, Maskable and Non-Maskable,
Interrupts, Interrupt Programming, Timings and Delays, Protected Mode-
Segmentation support registers, related instructions descriptors, memory management
through segmentation, logical to linear/physical address translation, protection in
segmentation, Privilege instructions, Paging-support registers, descriptors, linear to
physical address translation, TLB, page level protection, virtual memory, entering into
PM mode and returning back to RM mode

Advance Microprocessors: The Pentium and Pentium Pro Microprocessor:

Introduction to Pentium Microprocessor, Special Pentium Registers, Pentium Memory
Management, New Pentium Instructions, Introduction to 80386, 80486 and Pentium
processors.

Microprocessor based data acquisition and control system: Temperature control

system, Flow control system.

Text Books:
1. Microprocessor Architecture, Programming and application with the 8085,
R. S. Gaonkar, 5th Edition, Willey Eastern Ltd., 1995.
2. Microprocessors and Interfacing programming and Hardware, Douglas V.
Hall, 2nd Edition, McGraw Hill, 2003.
Reference Books:
1. Microprocessor and programming logic, K. L. Short, 2nd Edition, Prentice-
Hall India Pvt. Ltd., 2005.

Page 6 of 33
 2. Microprocessor Principles and Application, Ajit Pal Mc-Graw Hill, New
Delhi, 1999.
3. Advanced Microprocessor and Interfacing, B. Ram, 3rd Edition, McGraw-
Hill Publishing Company Ltd., New Delhi, 1995.
4. The 8086 microprocessor programming and Interfacing the PC, Kenneth J.
Ayala, 4th Edition, Penram International, 2000.
5. Intel Microprocessor; 8086/8088, 80186/188, 80286, 386, 486, Pentium
and Pentium Pro-Processor, B. B. Brey, Prentice-Hall India Pvt. Ltd.
6. An Introduction to The Intel Family of Microprocessors, James L.
Antonakos, Pearson Education, 2006.
7. Microcontroller Systems: The 8086/8088 Family Architecture,
Programming and Design Yu-Cheng Liu, Glean A. Gibson, 2nd Edition,
Prentice-Hall India Pvt. Ltd, 2003.
8. http://www.nptel.iitm.ac.in

Page 7 of 33
 INU 502 INSTRUMENTAL METHODS OF ANALYSIS
Teaching Scheme : 03 L + 0 T Total 03 Credit: 03
Evaluation Scheme: 15 CT1 + 15 CT2 +10 TA+ 60 ESE Total Marks: 100
Duration of ESE : 2hrs 30min.

Measurement Basics: Introduction, Electrical components and circuits, Operational

amplifiers in chemical instrumentation, Digital electronics and microcomputers

pH and Conductivity measurement: pH measurement-Construction, advantages,

disadvantages, factors affecting measurement, applications. Electrical conductivity
measurement-Electrical conductivity and molecular conductivity (definitions),
Methods of measurement, Applications.

Introduction to Chemical Instrumental Analysis: Introduction, Advantages over

classical methods. Ultraviolet (UV) and visible absorption instruments components,
Laws of Photometry, Monochromator, Colorimeter, Spectrophotometer: Single and
Dual Beam. Introduction to Electro analytical methods, potentiometry, voltametry,
coulometry

Atomic Spectroscopy: An introduction to spectrometric methods.

Atomic Flame Photometry: Principle, Constructional details, Fuel gases, Atomizer,
Burner, Optical and Recording System.
Atomic absorption Spectrometer: Theoretical concept and Instrumentation, hollow
cathode lamp, Burner and flames, Plasma excitation sources.
Atomic mass spectrometry: Theoretical concept and Instrumentation.

Molecular Spectroscopy: Introduction to ultraviolet/visible molecular absorption

spectrometry, Applications of ultraviolet/visible molecular absorption spectrometry.
Infra-Red (IR) Spectrophotometers: Basic components and their types.
Nuclear magnetic Resonance (NMR) Spectrometry: Principle, Nuclear spin, Chemical
shift, constructional details, Spin decoupler, Fourier transform NMR Spectroscopy.
Raman Spectrometry: Raman Effect, Components, Laser types. Photoacoustic and
photo thermal spectrometers.

Separation Methods: An introduction to chromatographic separations,

Chromatography- introduction, definitions, classification, Gas chromatography
apparatus, details of different parts, applications, factors affecting separation.
Introduction to Liquid Chromatography.

Methods of Gas Analysis: Oxygen, Carbon monoxide, Nitrogen analyzer, gas

density analyzer.

Refractometry: Principle, Abbe and Dipping types.

Text Books:
1. Hand Book of Analytical Instrumentation, R. S. Khandpur, 2nd Edition,
McGraw Hill Publication, 2006.
2. Instrumental Methods of Analysis, Willard, Merrit and Dean , 6th Edition,
CBS Publication, 1988.

Page 8 of 33
Reference Books:
1. Instrumental Methods of Chemical Analysis, G. W. Ewing, 5th Edition,
McGraw Hill Publication, 1985.
2. Instrumental Methods of Chemical Analysis, G.R. Chatwal and S.
Anand, 2nd Edition, Himalaya Publishing House, New Delhi, 2004.
3. Principles of Instrumental Analysis, Skoog, Holler, Nieman, 5th
Edition, Saunders College Publishing, 1998.
4. http://www.nptel.iitm.ac.in

Page 9 of 33
 INU 503 DIGITAL SIGNAL PROCESSING
Teaching Scheme : 03 L + 0 T Total 03 Credit: 03
Evaluation Scheme: 15 CT1 + 15 CT2 +10 TA+ 60 ESE Total Marks: 100
Duration of ESE : 2hrs 30min.

Introduction to signal processing: Introduction to DSP, Typical signal processing

operations, typical signal processing applications, advantages of digital signal
processing.

Structures for discrete time systems: Block diagram and signal flow representation
of constant coefficient linear difference equation. Basic structures for IIR
systems, basic structures for FIR systems, lattice structures.

Digital Filter design techniques: Design of discrete time IIR filters from continuous
time filters – Bilinear transformation, Impulse invariant transformation, Low pass IIR
digital filters, Spectral transformations, FIR filter design using windowing techniques,
Frequency sampling technique, and Computer aided design.

Algorithm implementation: Computation of DFT, FFT algorithms, Decimation in

time, Decimation in Frequency, Different algorithms of FFT such as DIT and DIF
where input and output is in order, radix-n algorithms.

Introduction to DSP Processors: Introduction to fixed point and floating point DSP
processors, architectural features of TMS320C67XX

Applications of DSP Processor: Speech, images, applications in biomedical

instrumentation, control systems, sampling rate alterations, introduction to sub-band
coding.

Text Books:
1. Digital signal processing- A computer based approach, S. K. Mitra, 2nd
Edition, Tata McGraw Hill, 2002.
2. Discrete time signal processing by A. V. Oppenheim, R. W. Schafer, 3rd
Edition, Prentice-Hall of India, 2001.
Reference Books:
1. Digital Signal Processing- A Practical Approach by E. C. Ifeachor, B. W.
Jarvis, , 2nd Edition, Pearson Education, New Delhi, 2002.
2. Digital signal processing –Principles, algorithms and applications, J. G.
Proakis, D. G. Manolakis, 3rd Edition, Prentice Hall of India, 2002.
3. Understanding Digital Signal Processing, R. G. Lyons, Pearson Education,
New Delhi, 1999.
4. http://www.nptel.iitm.ac.in

Page 10 of 33
 INU504 ELECTRONIC INSTRUMENTATION
Teaching Scheme : 03 L + 0 T Total 03 Credit: 03
Evaluation Scheme: 15 CT1 + 15 CT2 +10 TA+ 60 ESE Total Marks: 100
Duration of ESE : 2hrs 30min.

Experimental data and errors: fundamentals of measurements, measurement

recording and reporting, graphical presentation of data, Static and Dynamic
characteristics of instruments, dead zone, hysteresis, threshold, resolution, input and
output impedance, loading effects, calibration of instruments.

Electrical Lab practice: Safety, grounds, circuit protection devices, cables,

connectors, switches and relays, input impedance, output impedance and loading
power transfer and impedance matching.

Analog DC and AC meters: Classification, deflecting, controlling, damping,

breaking torques. Basic principles of operation of Ammeter and Voltmeter: PMMC,
Moving iron, Electro dynamic, Electrostatic: construction, Principle of operation.

Digital electronic meters: Counting and encoding, display devices, digital

voltmeters, digital multimeters.

D.C and A.C bridges and applications: Whetstone Bridge, Kelvin bridge, Schering
and Maxwell bridge, Wein bridge, Q meter.

The oscilloscope: Dual Trace Oscilloscope, sweep modes, active, passive probes,
delay line, Digital Storage Oscilloscope and its features like roll, refresh, sampling
rate, application of the same in instrumentation and measurement, sampling
oscilloscope, special purpose oscilloscope.

Time and frequency measurement: Universal counter and its mode – totalizing,
frequency, period, time interval, ratio, measurement errors, application of counters for
frequency meter, capacitance meter and timers, automation in digital instruments,
Tan-Delta measurement, Dielectric loss measurement.

Text Books:
1. Electronic Instrumentation, H. S. Kalsi, 3rd Edition, McGraw- Hill, New
Delhi, 2005.
2. Digital Measurement Techniques, T.S. Rathore, 2nd Edition, Narosa
Publishing House, 2004.

Reference Books:
1. Modern Electronic Instrumentation and Measurement Techniques, A. D.
Helfric and W. D. Cooper, 5th Edition, Prentice Hall of India, 2005.
2. A Course in Electrical and Electronic Measurements and Instrumentation, A.
K. Sawhney, 17th Edition, Dhanpat Rai and Sons, New Delhi, 2001.
3. Student Reference Manual, Stanley wolf, I. M. Richard Smith, 2nd Edition,
Prentice Hall of India.
4. Digital Instrumentation, A. J. Bouwens, McGraw Hill Book Co., 2001
5. http://www.nptel.iitm.ac.in

Page 11 of 33
 INU505 CONTROL SYSTEM ENGINEERING
Teaching Scheme : 03 L + 0 T Total 03 Credits: 03
Evaluation Scheme : 15 CT1 + 15 CT2 +10 TA+ 60 ESE Total Marks: 100
Duration of ESE : 2hrs 30min.

Introduction to control system: Basic definition of control system and related terms,
historical development of automatic control system, Different kinds of control system,
basic feedback structure, open loop and closed loop system.

Mathematical modeling of physical systems: Definition of physical system, linear,

non linear, time varying, time invariant systems, Transfer function models of
mechanical, electrical, thermal and hydraulic systems, Analogy between electrical and
mechanical system, Concepts of state, state variable, state model, state models for
linear continuous time functions.

Block diagram and signal flow graph analysis: Block diagram Algebra, reduction
rules, signal flow graph- definition, construction properties, Masons gain formula,
Application of gain formula to block diagrams.

Time response analysis: Standard test signals, Analysis of first order and second
order systems, performance specifications in time-domain, steady-state errors and
error constants.

Stability analysis: Concept of stability, Necessary condition for stability, Routh’s

stability criterion, Relative stability analysis, Root locus technique concepts, General
rules for construction of root locus, Root locus plots, effect of addition of poles and
zeros to system, Stability Analysis on Root Locus Plots by using Matlab.

Frequency response analysis: Relationship between time and frequency response,

Bode plots, stability margins for the Bode plot, stability analysis of system using bode
plot-MATLAB can be used to do the stability analysis, Introduction to polar plots,
Nyquist plot and its stability criterion.

State variable Analysis: solution of state equations, computation of state transition

matrix, concept of controllability and observability.

Text Books:

1. Control system Engineering, I. J. Nagrath, M. Gopal, 5th Edition, New Age

Intern (P) Ltd, 2000.
2. Modern Control Engineering, K. Ogata, 2nd Edition, Pearson Education India,
2002.

Reference Books:
1. Control System Principles and Design, M. Gopal, 2nd Edition, McGraw Hill
Publishing Company Limited, New Delhi, 2002.

Page 12 of 33
 2. Feedback and control systems, Joseph J. Distefano, Stubberud, Ivan Williams,
2nd Edition, Tata McGraw hill publishing Co. Ltd., 1995.
3. Control systems by Ashok Kumar, 1stEdition, McGraw Hill Publishing co.
Ltd., New Delhi.
4. Automatic Control System, Benjamin C. Kuo, 6thEdition, Prentice-Hall of
India,, New Delhi,
5. Feedback control system, Norman Nise , 5th Edition, Wiley publication, 2008.
6. http://www.nptel.iitm.ac.in

Page 13 of 33
 INU506 MICROPROCESSOR AND INTERFACING LAB
Teaching Scheme : 02 P Total 02 Credit: 01
Evaluation Scheme: 25 ICA + 25 ESE Total Marks: 50
Duration of ESE : 3 Hrs

Minimum 8 Experiments should be conducted from the sample list given below.
However experiment beyond the list and based on curriculum of INU501 may be
conducted. Any four from Group A and any four from Group B
Group A:
1. Addition and subtraction of 8/16/32 bit numbers
a. Number should be placed in memory.
b. Multiplication and division of 8 bit numbers using add and shift
method
2. Write an assembly language program to handle RST7.5 interrupt
3. Block transfer instruction for 8 bit number
4. Searching and Sorting of 8 bit number
5. Write 8086 ALP to convert an analog signal in the range of 0V to 5V to its
Corresponding digital signal using either successive approximation ADC
or dual slope ADC.
6. Write 8086 ALP to interface DAC and generate following waveforms on
oscilloscope,
a. Square wave - Variable Duty Cycle and frequency,
b. Ramp wave - Variable direction,
c. Trapezoidal wave,
d. Stair-case wave.
Group B:
7. Write 8086 ALP to rotate a stepper motor for given number of steps at a
given angle and in the given direction of rotation based on the user choice.
8. Write 8086 ALP to read command line arguments using PSP(Program
Segment Prefix) and implement “DOS COPY Command “
9. Interfacing 7-segment displays with 8255.
10. Interfacing Keyboard matrix with 8255.
11. Interfacing DAC
12. Interfacing ADC
13. Programming for 8253.
14. Software implementation of ADC
15. Observing timing diagram on CRO.
16. Interfacing programs must be based on applications used in process
industries.

Note:
ICA- The Internal Continuous Assessment shall be based on the practical record and
Knowledge/skill acquired. The performance shall be assessed experiment wise
by using continuous assessment formats A and B.

ESE- The End Semester Exam shall be based on performance in one of the
experiments and may be followed by sample questions.

Page 14 of 33
 INU507 INSTRUMENTAL METHODS OF ANALYSIS LAB

Teaching Scheme : 02 P Total 02 Credit: 01

Evaluation Scheme : 25 ICA + 25 ESE Total Marks: 50
Duration of ESE : 3hrs

Minimum 8 Experiments should be conducted from the sample list given below.
However experiment beyond the list and based on curriculum of INU502 may be
conducted.

1. To find pH of given solution.

2. To find conductivity of given solution.
3. Analysis of color by using colorimeter.
4. To analyze UV/VIS spectro-photometer for
a. Single Beam
b. Double Beam
5. To determine the Refractive index by using refractometer
6. To study flame photometer.
7. Use of gas chromatography for analyzing components of gas mixtures
8. To study Atomic absorption spectrometer(AAS)
9. To study Oxygen Gas Analyzer.
10. To study IR spectro-photometry.

Note:
ICA- The Internal Continuous Assessment shall be based on the practical record and
Knowledge/skill acquired. The performance shall be assessed experiment wise
by using continuous assessment formats A and B.

ESE- The End Semester Exam shall be based on performance in one of the
experiments and may be followed by sample questions.

Page 15 of 33
 INU508 ELECTRONIC INSTRUMENTATION LAB
Teaching Scheme : 02 P Total 02 Credit: 01
Evaluation Scheme : 25 Internal + 25 External Total Marks: 50
Duration of ESE : 3hrs

Minimum 8 Experiments should be conducted from the sample list given below.
However experiment beyond the list and based on curriculum of INU504 may be
conducted. Any four from Group A and any four from Group B
Group A:
1. Measurement of resistance (high, medium, low) using Double Kelvin Bridge.
2. Measurement of inductance.
3. Measurement of capacitance.
4. Phase and frequency measurement on CRO using Lissajous pattern
5. Study of digital voltmeter, digital multimeter.
6. Study of recorders.
Group B:
7. Digital measurement of phase and frequency.
8. Study of AC and DC meters.
9. Study and application of Universal counters
10. Study of DSO (measurement of response time of relay using DSO/ECG signal
measurement)
11. Study of DMM and RMS meter,
12. Study of Arbitrary waveform generator
13. Study of Megger

Note:
ICA- The Internal Continuous Assessment shall be based on the practical record and
Knowledge/skill acquired. The performance shall be assessed experiment wise
by using continuous assessment formats A and B.

ESE- The End Semester Exam shall be based on performance in one of the
experiments and may be followed by sample questions.

Page 16 of 33
 INU509 DIGITAL SIGNAL PROCESSING LAB
Teaching Scheme : 02 P Total 02 Credit: 01
Evaluation Scheme : 25 ICA + 25 ESE Total Marks: 50
Duration of ESE : 3hrs

Students are supposed to write the programs (at least eight) on general-purpose
computer using any development environment (MATLAB/ C/C++) or on any
DSP processor and development environment

1. Digital signal generation

2. Simple operations on signals
3. Verify the properties of Linear Convolution.
4. Compute Discrete time Fourier transform.
5. Discrete Fourier Transform - Direct computation, DIT algorithm, DIF
Algorithm
6. Design and implement FIR filter by windowing and Frequency sampling
method.
7. Design and implement IIR Filter with Butterworth and Chebyshev
approximation.
8. FIR filters implementation using DSP Processor.
9. IIR filter implementation using DSP Processor.

Note:
ICA- The Internal Continuous Assessment shall be based on the practical record and
Knowledge/skill acquired. The performance shall be assessed experiment wise
by using continuous assessment formats A and B.

ESE- The End Semester Exam shall be based on performance in one of the
experiments and may be followed by sample questions.

Page 17 of 33
 INU510 CONTROL SYSTEM ENGINEERING LAB
Teaching Scheme : 02 Total 02 Credit: 01
Evaluation Scheme: 25 ICA +25 ESE Total Marks: 50
Duration of ESE : 3hrs

Minimum Eight Experiments should be conducted from the sample list given
below.

Experiments Based on hardware:

1. Analysis of the performance of an open and closed loop control system
2. Analysis of the performance of a First order system
3. To obtain the performance specifications of a Second order system
4. Determination of transfer function of an armature controlled d. c. motor.
Experiments based on Software
1. Introduction to MATLAB, MATLAB’s Simulink and control systems toolbox
(with some examples) or any other control system related software package.
2. Compare and plot the unit-step responses of the unity-feedback closed loop
systems with the given forward path transfer function. Assume zero initial
conditions. Use any computer simulation program.
3. Study of effect of damping factor on system performance by obtaining unit
step response and unit impulse response for a prototype standard second order
system.
4. Write a program that will compute the step response characteristics of a
second order system i.e. percent overshoot, rise time, peak time and settling
time.
5. Study and plot the unit step responses of addition of a pole and a zero to the
closed loop transfer function.
6. Stability analysis on Root Locus Plot for given control system
7. Stability analysis on Bode Plot for given control system
8. Stability margins, and gain and phase crossover frequencies on the plots
generated
using the MATLAB functions Nyquist and bode .
9. Plot and comment on various properties of any three systems (Problems) using
 Root locus technique
 Bode plots
 Nyquist plots.

Note:
ICA- The Internal Continuous Assessment shall be based on the practical record and
Knowledge/skill acquired. The performance shall be assessed experiment wise
by using continuous assessment formats A and B.

ESE- The End Semester Exam shall be based on performance in one of the
experiments and may be followed by sample questions.

Page 18 of 33
 INU 511 SELF STUDY -I
Teaching Scheme: 00L + 00 T Total 00 Credits: 02
Evaluation Scheme: 25 TA Total Marks: 25

Self study-I is based on one class test each, on the basis of 20% curriculum of the
courses INU501, INU502, INU503 and INU504 to be declared by respective course
coordinator at the beginning of the semester. These class tests should be conducted
separately for each course and after CT2. The marks of all such class tests then shall
be converted to out of 25. One faculty member shall be appointed as course
coordinator for Self Study I and his/ her teaching work load shall be considered as one
hr/week.

Page 19 of 33
 INU601 MICROCONTROLLER AND ITS APPLICATIONS
Teaching Scheme : 03 L + 0 T Total 03 Credit: 03
Evaluation Scheme: 15 CT1 + 15 CT2 +10 TA+ 60 ESE Total Marks: 100
Duration of ESE : 2hrs 30min.

Introduction to microcontrollers: Comparison of microprocessor and

microcontrollers, architecture of 8051 and study of SFR, Overview and features, On
chip and external memory map, Interrupt Structure, Timers and Counters, Generating
Software and Hardware Delays, Serial Communication, Power Down and Idle mode .

Assembly language programming for 8051: Architecture and operation, pin out
diagram microcontroller instruction classification, instruction set Arithmetic and
logical operations, jump and call instructions etc., Writing assembly language
programming based on instruction set, stacks and subroutines.

Interrupts of 8051: Serial data I/P and O/P, serial data transmission and
communication counters and timers, timer modes timer/counter programming.

8051 microcontroller interfacing with: 8255, Keyboard and Display devices like
LED, LCD, Stepper motor interfacing, A/D and D/A chips external memories (RAM
and EPROM), Memory interfacing concepts, I/O interfacing concepts, I/O expansion,

Design of dedicated systems using 8051 for temperature indication control, Flow
indication control, stepper motor control, Embedded control systems, Smart
transmitters.

Bus interfacing standards: Serial: I2C, CAN, Parallel: ISA, PCI, PCIX.

Text Books:
1. 8051 Microcontroller: Architecture, Programming and applications,
Ayala K.J., 2nd Edition, Penram International, 2003.
2. The 8051 Microcontroller and Embedded System, M.A. Mazidi, Pearson
Education, 2004.

Reference Books:
1. Programming and customizing the 8051 Microcontroller, Myke Predko,
McGraw-Hill, New Delhi, 1999.
2. Intel’s PIC AVR, Motorola Manual.
3. http://www.nptel.iitm.ac.in

Page 20 of 33
 INU602 POWER ELECTRONICS
Teaching Scheme : 03 L + 0 T Total 03 Credit: 03
Evaluation Scheme: 15 CT1 + 15 CT2 +10 TA+ 60 ESE Total Marks: 100
Duration of ESE : 2hrs 30min

Introduction: Introduction to basic thyristers, Design of gate triggering circuits using

Thyristor, Thyristor protection circuits, Modern power semiconductor devices and
their characteristics, gate drive specifications, ratings, applications.

Thyristor Commutation Techniques: Principles of Natural commutation, Design of

Forced commutation circuits: Self commutation, Impulse commutation, Resonant
pulse commutation, Complementary commutation, External pulse commutation.

Phase Controlled Rectifiers: Single phase rectifiers: Half wave, Center tapped,
Bridge (half controlled and fully controlled) with R and RL load

Three phase rectifiers: Half wave, Bridge with R and RL load, Effect of source
inductance, voltage and current harmonics analysis, dual converters, Power factor
improvement methods.

DC Chopper: Basic chopper, continuous and discontinuous current conduction;

TRC, CLC methods, Classification of choppers, step-up chopper.

AC Voltage Controller: Types of ac voltage controllers, single-phase ac voltage

controllers with R and RL load, transformer tap changers.

Inverters: Single phase inverters: series, parallel and bridge configurations with R
load, PWM inverters. Three phase inverters with 1200 and 1800 conduction with R
and RL load, voltage control and harmonics reduction.

Speed control of DC motors: Using different rectifiers, principles of regenerative

braking, principles of two/ four quadrant chopper drives, control using multiphase
choppers, microprocessor control of DC drives.

Speed control of Induction motors: Stator voltage control, rotor voltage control,
frequency control, voltage and frequency control, microprocessor control of AC
drives.

Application of Power Electronics: Battery charging, Power extraction from non-

conventional energy sources.

Text Books:
1. An Introduction to Thyristor and Their Application, M. Ramamurty, 2nd
Edition, Affiliated East-West Press Private Limited, New Delhi-110 020
(India), 1991.
2. Power Electronics: Circuits, Devices, and Applications, M. H. Rashid, 2nd
Edition, Prentice Hall of India Private Limited, New Delhi-110 001(India),
1994.

Page 21 of 33
Reference Books:
1. Power Electronics, Singh M. D., Khanchandani K. B., 2nd Edition, McGraw-
Hill Publishing Company Limited, New Delhi (India), 1998.
2. Power Electronics by P. S. Bimbhra, 2nd Edition, Khanna Publishers, Delhi-
110 006 (India), 1998.
3. Electric Drives by N. K. De, P. K. Sen, 5th Edition, Prentice Hall of India
Private Limited, New Delhi-110001(India), 1999.
4. Principles of Thyristorised Converters, De G. Oxford and IBH Publications,
1982.
5. http://www.nptel.iitm.ac.in

Page 22 of 33
 INU603 MATERIAL SCIENCE AND PROCESSES
Teaching Scheme : 03 L + 0 T Total 03 Credit: 03
Evaluation Scheme: 15 CT1 + 15 CT2 +10 TA+ 60 ESE Total Marks: 100
Duration of ESE : 2hrs 30min.

Introduction to Engineering Materials: Materials classification and engineering

requirements of materials, factor affecting the selection of materials for engineering
purposes, properties of engineering materials , testing of materials, tensile test, torsion
and shear test, compression test, impact test, hardness test, fatigue test, S-N diagram,
creep of materials, Erichsen test.

Introduction to Manufacturing Processes: Crystal structure of metals and alloys:

FCC, BCC, HCP and structure -property relationships. Casting, cold working and
hard working processes like rolling, forging, extrusion, etc.

Materials and their applications for electrical and electronic component:

Materials for resistors, properties and applications, Superconducting materials,
Transducers materials, Semiconductors-commonly used type working applications.
Thermistors, Piezoelectric, Ferro-electric and Ferro-ceramic materials, die-electric
materials and dielectric constant, capacitor insulating materials, magnetic materials,
soft and hard magnetic materials ferrites and di, para, antiferro, ferromagnetism, its
applications

Properties of fibrous material, ceramic, mica, glass, rubber, plastics, insulating waxes,
varnishes and coolants

Thermocouple materials, soldering materials, fuse materials, contact materials,

fluorescent and phosphorescent materials

Processing of electronic materials: Crystal growth, purification junction IC

fabrication processes of galvanizing and impregnatism.

Advanced materials: Nano-materials and carbon tubes

Text Books:
1. The Structure and Properties of Materials, Vol.- IV , R. M. Rose, L. A.
Shepard, John Wulff, John Wily and Son Inc.1998
2. Materials Science and Engineering, V. Raghavan, Prentice Hall,
Reference Books:
1. Material for Engineering Technician, Raymond A. Higgins, 2nd Edition,
ELBS, 1998.
2. Engineering Material, B. K. Agrawal, Mc-Graw Hill Publishing Company,
2000.
3. Material science and Metallurgy by Dr. Kodgire, V. D. 12th Edition, Everest,
Publishing House, 2002.
5 Engineering electronic material, Dr P. S. Satsangi, IIT Delhi.
6 Electrical Engineering Materials, W. Alagappan, N.T. Kumar, McGraw Hill,
1998.
7 http://www.nptel.iitm.ac.in

Page 23 of 33
 INU604 PROCESS CONTROL
Teaching Scheme : 03 L + 1 T Total 04 Credit : 04
Evaluation Scheme: 15 CT1 + 15CT2 + 10TA+60 ESE Total Marks: 100
Duration of ESE : 2hrs 30min.

Introduction to Process control: Process characteristics, Types of processes, process

characteristics and controllability, self regulating and non self regulating. Processes,
interacting & non-interacting processes. Relative gain array & it’s analysis.

Dynamic Behavior of systems: Dynamic Behavior of First Order, second order and
higher order systems, Dynamic systems with Dead Time/Inverse Response, Computer
simulation of process dynamics, linearization of nonlinear systems

Controllers: Open Loop & Closed Loop Control System, .Multi-loop and
Multivariable Process control system, Design consideration for P, PI, PID, ON OFF
Controller, Tuning of PID controller, Electronic PID controller, pneumatic
controllers,

Design of Feed Back controllers: Outline of design problems; simple performance

criteria, time integral performance content, selection of a feedback controller;
controller tuning using Cohen-Coon method, Bode Stability criterion, gain and phase
margins, Ziegler-Nichols Turning Technique.

Analysis and Design of Advanced Control systems: Feedback control systems with
large dead time or inverse response, feed forward control, Cascade control, ratio
control, auto selective control, Split range Control, adaptive control system,
inferential control system

Application of advanced Process Control to Unit operations: Distillation Column,

heat exchangers, boiler (Basic controls).

Industrial Process Control: Process control for power plant, cement industry, paper
pulp industry, petroleum industry.

Text Books:
1. Process Control System, F. G. Shinskey, 2nd Edition, McGraw Hill, 1979.
2. Chemical process control, George Stephanopoulos, Prentice-Hall of India,
2003.

Reference Books:
1. Process Control Handbook, Bela G. Liptak., Chilton Book Company, 2001.
2. Computer Based Industrial Control, Krishnakant, Prentice-Hall of India, 1997
3. Process Instrumentation & Control Handbook, Considine, 5th Edition, McGraw
Hill, 1995.
4. Instrumentation for Process Measurement & Control, Norman A. Anderson, 3rd
Edition.
5. Process Systems analysis and Control, D.R. Coughanour, 2nd Edition, McGraw
Hill publications.
6 Process Dynamics and Control, D. E. Seborg, T. F. Edger, and D. A.
Millichamp, 2nd Edition, John Wiley and Sons, 2004.

Page 24 of 33
 7 Shreve's Chemical Process Industries by George Austin, 5th edition, McGraw
hill Publication 1990.
8 Automatic Process Control, D. Eckman, Wiley Eastern Publication
9 http://www.nptel.iitm.ac.in

Page 25 of 33
 INU 605 PROJECT ENGINEERING & MANAGEMENT
Teaching Scheme : 03L+ 0T Total 03 Credit: 03
Evaluation Scheme: 15 CT1 + 15CT2 + 10TA+60 ESE Total Marks: 100
Duration of ESE : 2hrs 30min.

Introduction: Basics of Project Engineering & Project Management, Project

Objective, Need, Scope, Project Procedure, Project Schedule, Project Specification,
Work Breakdown Structure, Steps in Project Management, Project Implementation,
Work hour Estimation, Cost Estimation, Project Kickoff. Project Management Tools:
Program Evaluation & Review Techniques (PERT) & Critical Path Method (CPM)

Project Control: Role of Instrumentation Engineer in Execution of Project. Design

and Detailed Engineering documents required for Project Completion – Process flow
sheet, Mechanical flow sheet, Process & Instrumentation Diagram (P&ID),
Instrument Symbols and Identification (ISA S5.1), Instrument Index sheet, Instrument
Specification sheet, Instrument data sheet, Sizing Calculation for Orifice Plate (ISO
5167), Control Valve (ISA S-75.01), Input/output List, Loop wiring diagram, Control
System Engineering documents such as Point data base, Interlock List, Cause &
Effect diagram, Logic Diagram, Functional Loop Schematic.

Field Engineering Activities: Preparation of Instrument Installation Tender,

Instrument Cable details such as Cable Construction, Types of Cable (Signal, Power,
Control, Compensating Cable, Foundation Field Bus Cable, and Fiber Optic Cable).
Selection of cables and applicable Standards (BS, IEC), Cable Schedule.
Instrument Cable installation, Instrument Location Layout, Cable Tray Layout, Cable
Accessories (Cable Tray, Cable Gland) Testing of Cables. Junction Box and JB
Schedule, Instrument Piping & Tubing.
Control Panels – Control Panel Types, Control Panel GA Drawing, Control Panel
Wiring Diagram & earthing. Control Room Layout.

Procurement Activities: Material Requisition / Inquiry, Vendor Offer Evaluation,

Technical Bid Analysis (TBA)/Evaluation. Purchase Order, Vendor Document
Review and Inspection at Vendor works, Shipping Receiving & Storing Instruments.

Project Construction & Start Up : Installation & Commissioning:- Installing

instrument System, Typical Installation Procedure, Coordinating work among craft,
Calibration of Instruments, Check list for good installation practices, Electric &
pneumatic Process Connection, Loop Checking/testing Procedure, Factory
Acceptance Test (FAT) Procedure, Onsite Inspection & Testing (SAT) Procedure,
FAT/SAT Report, Tuning control Loop, Evaluating Process Upsets & disturbances,
Performance Trial & final handover.

Text Books:
1. Applied instrumentation in process industries volume III, Andrew &
Williams, 3rd edition, Gulf Publications.
Page 26 of 33
 2. Introduction to Operations Research, Hiller and Lieberman, 7th Edition,
Tata McGraw Hill, 2003.

Reference Books:
1. Instrument Engineers Handbook, Process Measurement Volume-I and
Process Control Volume- II, Liptak B. G., Chilton Book Company, 2001.
2. Project Management- A systems approach to planning, scheduling and
controlling, Harold Kerzner, 9th Edition, 2006.
3. Management Systems, John Bacon, 3rd Edition, ISA Publications, 2003.
4. Batch Control System, Fisher T. G. 3rd Edition, ISA Publications, 2001.
5. Instrument Installation Project Management, ISA Publications 2000.
6. http://www.nptel.iitm.ac.in

Page 27 of 33
 INU606 MICROCONTROLLER AND ITS APPLICATIONS LAB
Teaching Scheme : 02 P Total 02 Credit: 01
Evaluation Scheme: 25 ICA +25 ESE Total Marks: 50
Duration of ESE : 3hrs

Minimum Eight Experiments should be conducted from the sample list given
below.

1. Simulator and Programmer for 8051

2. Simple Arithmetic Programs
3. Interfacing of A/D and D/A with AT89C51
4. Blinking of LED using AT89C51
5. Frequency Divider Using AT89C51
6. External Interrupt with AT89C51
7. Interfacing a Keypad with AT89C51
8. Interfacing PIC16F877 Microcontroller with an LCD
9. Blinking LED with PIC16F877A
10. PIC Serial Communication using Serial Peripheral Interface (SPI)

Note:

ICA- The Internal Continuous Assessment shall be based on the practical record and
Knowledge/skill acquired. The performance shall be assessed experiment
wise by using continuous assessment formats A and B.

ESE- The End Semester Exam shall be based on performance in one of the
experiments and may be followed by sample questions.

Page 28 of 33
 INU607 POWER ELECTRONICS LAB
Teaching Scheme : 02 P Total 02 Credit: 01
Evaluation Scheme: 25 ICA +25 ESE Total Marks: 50
Duration of ESE : 3hrs

Minimum Eight Experiments should be conducted from the sample list given
below. Any four from Group A and any four from Group B

Group A:

1. Observe characteristics UJT Relaxation oscillator.

2. Observe characteristics of SCR
3. Observe characteristics Triac
4. Power control using SCR.
5. Power control using Triac.
6. Single phase controlled Rectifiers.
7. Single phase half controlled Rectifiers.
8. Single phase fully controlled Rectifiers.

Group B:

9. Single phase inverter using transistor/ MOSFET/IGBT.

10. Basic step-down chopper.
11. Basic step-up chopper.
12. Speed control of D.C. motor using controlled rectifiers.
13. Speed control of D.C. motor using choppers.
14. Speed control of A.C. motor using inverter.

Note:

ICA- The Internal Continuous Assessment shall be based on the practical record and
Knowledge/skill acquired. The performance shall be assessed experiment
wise by using continuous assessment formats A and B.

ESE- The End Semester Exam shall be based on performance in one of the
experiments and may be followed by sample questions.

Page 29 of 33
 INU608 PROCESS CONTROL LAB
Teaching Scheme : 02 P Total 02 Credit : 01
Evaluation Scheme: 25 ICA +25 ESE Total Marks: 50
Duration of ESE : 3hrs

Minimum Eight Experiments should be conducted from the sample list given
below.

1. Design of an electronic ON-OFF controller and plot the characteristics of

natural zone of controller
2. Design an electronic PID controller
3. Simulation of pneumatic and hydraulic controllers for single and double acting
cylinder.
4. To obtain and plot the pressure profile across orifice and venturimeter.
5. To control the pressure in closed tank by using closed loop control system and
plot its characteristics.
6. To interface Pressure control loop to soft PID and plot its characteristics
7. Design of Cascade Control using Cascade control system trainer.
8. Design ratio control system for flow control application.
9. To determine the mathematical model of the given process.
10. To understand the effect of interacting and noninteracting systems as single or
multicapacity process.
11. Analysis of first order and second order system.

Note:

ICA- The Internal Continuous Assessment shall be based on the practical record and
knowledge/skill acquired. The performance shall be assessed experiment
wise by using continuous assessment formats A and B.

ESE- The End Semester Exam shall be based on performance in one of the
Experiments and may be followed by sample questions.

Page 30 of 33
 INU 609 MINOR PROJECTS
Teaching Scheme : 02 P Total 01 Credit: 02
Evaluation Scheme: 25 ICA+25ESE Total Marks: 50

The Minor Project consist of Design and fabrication of Instrumentation oriented

projects based on following areas
1. Process Instrumentation and Industrial Automation
2. Biomedical Instrumentation
3. Electronic Instrumentation
4. Microprocessor based Instrumentation.
5. Virtual Instrumentation

The minor project work should be carried out in Laboratory only. The topic may be
given to the individual student or group of not more than three students. The
evaluation will be based on the quality of work, report, presentation and
demonstration by the students in front of the Expert committee from the department.

Note:

ICA- The Internal Continuous Assessment shall be based on the practical record and
Knowledge/skill acquired. The performance shall be assessed experiment
wise by using continuous assessment formats A and B.

ESE- The evaluation shall be based on demonstration by the students in

front of the Expert committee from the department.

Page 31 of 33
 INU610 SELF STUDY-II

Teaching Scheme: 00L + 00 T Total 00 Credits: 02

Evaluation Scheme: 25TA Total Marks: 25

Self study-II is based on one class test each, on the basis of 20% curriculum of the
courses INU601, INU602,INU604 and INU605 to be declared by respective course
coordinator at the beginning of the semester. These class tests should be conducted
separately for each course and after CT2. The marks of all such class tests then shall
be converted to out of 25. One faculty member shall be appointed as course
coordinator for Self Study I and his/ her teaching work load shall be considered as one
hr/week.

Page 32 of 33
 INU611 INDUSTRIAL LECTURE I
Teaching Scheme: 01L + 00 T Total: 01
Evaluation Scheme: 00 ICA + 00 ESE Total Marks: 00
Duration of ESE: 00hrs. Credits: 00
(* Credits shall be awarded on the basis of combined assessment of INU611 and
INU711.)

Industrial lectures shall be arranged by the experts/Officials from Industries/Govt.

undertaking organizations/ Private Sectors/Public Sectors. These lectures will include
various aspects of project planning, industrial automation, use of control systems in
industries, power plant instrumentation, biomedical instrumentation and it’s scope in
the medical industry modernisation. Topics of Industrial Lectures shall be general in
nature and should not be the specific contents from the curriculum.

Page 33 of 33