Scribd
Upload
226 views3 pages

How Stresses Are Transferred From RC Columns To Footings

Stresses from loads on columns are transferred to footings through two main methods: (1) extending longitudinal reinforcement bars from the column into the footing to transfer compressive and tensile forces, with a minimum of four bars extending a sufficient distance for stress transfer; and (2) using dowels embedded in both the column and footing to transfer compressive and tensile forces, with a minimum of four dowels of appropriate size and embedment. Proper design and detailing of this reinforcement and doweling is crucial to ensure sound transfer of stresses from columns to the underlying footing and soil.

Uploaded by

venkateswara rao Pothina
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
226 views3 pages

How Stresses Are Transferred From RC Columns To Footings

Stresses from loads on columns are transferred to footings through two main methods: (1) extending longitudinal reinforcement bars from the column into the footing to transfer compressive and tensile forces, with a minimum of four bars extending a sufficient distance for stress transfer; and (2) using dowels embedded in both the column and footing to transfer compressive and tensile forces, with a minimum of four dowels of appropriate size and embedment. Proper design and detailing of this reinforcement and doweling is crucial to ensure sound transfer of stresses from columns to the underlying footing and soil.

Uploaded by

venkateswara rao Pothina
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

The Constructor - Civil Engineering Home

How Stresses are Transferred from R.C. Columns to


Footings?
theconstructor.org/practical-guide/stresses-transferred-columns-footings/32419

April 28,
2019

A proper understanding of the transfer of stresses(generated due to applied loads) from


columns to the footings or piles is crucial for the design of sound footings. Factored
forces and moments at the base of columns are transferred to the supporting
foundations by bearing on concrete and by the extension of longitudinal reinforcement
into the footing or provision of dowels.

Either technique should be executed based on the specifications of the applicable design
codes such as ACI 318-14. The detailing of reinforcement shall be executed adequately
for proper distribution of stresses to footings and then further over the underlying soil
layer.

How Stresses are Transferred from Columns to Footings?

1. Extending the Longitudinal Steel into the Footing


Extended reinforcement shall be designed to transfer compressive forces that
exceed the lesser of the concrete bearing strengths of either the supported
member or the foundation, and any calculated tensile force across the column-
footing interface.
At least four bars should be extended.
The stress-transfer bars should project into the base a sufficient compression-
embedment distance to transfer the stress in the column bars to the base
concrete.

1/3
In any case, a minimum steel area of 0.5% of the column-area should be supplied
for load transfer.

Fig. 1: Extending Longitudinal Reinforcement into the Footing

2. Dowel
Dowels shall be designed to transfer compressive forces that exceed the lesser of
the concrete bearing strengths of either the supported member or the foundation,
and any calculated tensile force across the column-footing interface.
At least four dowels should be used.
The dowel diameter should not exceed the column-bar diameter by more than 0.15
in.
If the required dowel length is larger than the footing depth less 3 in, either
smaller-diameter bars with the equivalent area should be used or a monolithic
concrete cap should be added to increase the concrete depth.
The dowels should provide at least one-quarter of the tension capacity of the
column bars on each column face.
The dowels should extend into the column a distance equal to that required for
compression lapping of column bars.

Fig. 2: Dowels

2/3
3/3

You might also like